316442301 Frigidaire Oven 2600W âŁ8 Coil Element is a resistive tubular coil heating element ârated at 2600 watts, typically installed as a primary oven heating element âin Frigidaire electric ranges. As a direct-resistance heater â˘it converts electrical energy into heat⢠through itsâ coil windings; in common 240 V household installations its design implies an order-of-magnitude DC resistance in the low tens of ohms (R â V²/P, âŁâ22 Ί at 240 V)and it is âconfigured with multiple coil turns and mounting/terminal â˘fittings to fit specific oven cavities and â˘chassis mounting points.
Inside the appliance the element serves as a controlled heat source for baking and roasting cycles and interfaces electrically and thermally with several systems: the oven control board and its relays or solid-state switches âŁthat apply mains voltage,the wiring harness and terminal block that carry supply and ground,the oven temperature sensor/thermistor and thermostat that close the feedback loop for temperatureâ control,and any fan or air-circulation system that affects heat distribution. The element also works in concert with safety devices such as thermal âŁcutouts, fusesand grounding paths; mechanical mounting, insulation and the âŁelement’s exposed surfaceâ geometry influence â˘heat transfer to the cavity and the uniformity of cooking âresults.
This article explains the element’s⢠function, how to verify electrical and thermal compatibility with specific Frigidaire models (electrical âŁrating, terminal type, physical dimensions), common failure symptoms (open circuit, short-to-ground, hot spots, discoloration, uneven heating), stepâbyâstep troubleshooting procedures (visual inspection, continuity and resistance checks, safe voltage âverification at terminalsand insulation-to-ground tests)and âpractical replacement considerations (matching wattage/voltage, correct connector and mounting fit, wiring gauge and secure terminalsand inspection of related controls and safety devices). Emphasis will be placed on diagnosticâ methods a technician or informed appliance owner⣠can use to identify a âŁdefective element and⢠the key factors to confirm before installing a replacement.
Table â˘of âContents
- Functional Role and Electrical and Thermal Specifications of the â˘Oven Coil Heating Element
- How the 316442301 Frigidaire Oven 2600W 8 Coil Element Operates Within the Oven’s Electrical and Thermal Systems
- common Failure Modes, observableâ Symptomsand âDiagnostic Tests for coil Elementâ Degradation
- Compatibility, Replacement Considerationsand StepâbyâStep Installation âŁGuidelines âfor the â˘316442301 Coil⣠Element
- Q&A
- Wrapping Up
Functional Role and Electrical and Thermal Specifications of the Oven Coil heating Element
The 316442301 Frigidaire Oven 2600W 8 Coil Element functions as the oven’s primary resistiveâ heater, converting electrical power into radiant and convective heat to maintain set temperatures during bake and broil cycles. âThe eight-turn⢠coil geometry increases âexposed âsurface area and spreads heat more uniformly âthan a single straight element, reducing hot spots and contributing to more even oven cavity temperature distribution. Technicians replacing this component should confirm the part number, nominal wattageâ and terminal/mounting configuration match the oven’s specificationsâ to avoid changes in heating performance or electrical loading.
Electrically the element is specified at 2600 watts for the appliance supply (commonly 240 volts),yielding a cold resistance near⤠22.2 ohms (R = V²/P); measured cold resistance will be lower than the steady-state resistance as the element⤠alloy’s resistivity increases with temperature.Thermally the surface reaches several hundred degrees Celsiusâ during operation, providing rapid radiant heat while oven air and⤠cookware add thermal inertia; therefore â˘bake times and thermostat cycling depend on element placement, oven insulationand control calibration.â Before installation verify circuit breaker rating, wire gaugeand that the control thermostat isâ rated⣠for a⢠2600 W load to maintain safe, predictable operation.
- Compatibility checks: match wattage,voltage,terminal spacing,and mounting bracket style.
- Electrical check: measure cold resistance to confirm element continuity and absence of short to⣠chassis.
- Installation practice: use appropriate wire gauge⣠and a dedicated circuit; secure terminals and ground connections.
| Item | Description |
|---|---|
| Wattage | 2600 W nominal |
| Rated Voltage | Typically 240 V (confirm â˘appliance rating) |
| Cold Resistance | Approximately 22.2 Ί at room temperatureâ (calculated) |
| Element Type | Eight-turn coiled tubular⤠heating element, high-resistance alloy sheath |
| Typical Surface Temperature | several hundred °C (commonly 400-600 °C under load) |
How the â316442301 Frigidaire Oven 2600W â8 Coil Element Operates Within the Oven’s Electrical and Thermal Systems
The 316442301 Frigidaire Oven âŁ2600W 8 Coil Element âis aâ resistive heating element that converts electrical energy into âthermal energyâ inside⤠the oven cavity. at its rated 2600 W output the element is designed for the oven’s 240â V supply used in most⤠residential⣠ranges, drawing approximately 10.8 A and presenting an electrical resistance on â˘the order of 22 Ί (V²/Pâ = 240²/2600 â 22 Ί). Electrically, âthe â¤coil is integrated into the oven’s control loop and is driven by relays or solid-state switching onâ the control board; the board cycles power to the element to regulate temperature⢠according to sensor feedback.Proper âoperation requires correct terminal connections, compatible switching⤠components rated âfor the element’s currentandâ intact insulation⢠to avoid leakage or short circuits that would degrade performance or safety.
Thermally, the coil geometry and placement determine heat distribution and the element’s time constant: an 8-coil arrangement provides surface area for radiativeâ and convective transfer, heating the oven cavity âand cookware by⣠a mix ofâ direct radiation and heated-air convection.The element will cycleâ on and off during normal â˘use as the thermostat or electronicâ controller maintains setpoint temperature; repeated cycling and thermal expansion are⤠common stressors that can lead to open circuits or⢠grounding⤠faults over time. For compatibility and troubleshooting, match replacement elements on â¤wattage, terminal layoutand mounting brackets; âa cold resistance measurement near the calculated value indicates continuity, while an open circuit or a low-resistance short to chassis indicates â¤failure⣠or grounding. Practical examples: an oven that never reaches temperature often âshows an open element or reduced power delivery, whereas tripping⢠breakers or blown fusesâ can indicate element shorting or a wiring fault.
- Rated power: 2600 W -â determines heat-up rate â¤and controller duty â˘cycle
- Nominal supply: typically 240⣠V in residential ovens
- Approximate cold resistance: ~22 Ί
- Control interface: relay/SSR on oven control board or mechanical thermostat
- Common failures: open circuit, âŁshort to ground, terminal corrosion
| Item | Description |
|---|---|
| Power rating | 2600 W – determines elementâ heat output |
| Nominal voltage | Approximately 240 V (split-phase residentialâ supply) |
| Approximate⤠resistance | ~22 Ί (cold, calculated) |
Common Failure Modes, Observable Symptomsand â¤Diagnostic Tests⢠for Coil⤠Element Degradation
The 316442301 Frigidaire Oven 2600W 8 Coil Element is a resistive heating coil sized and mounted for⢠select⤠Frigidaire ranges; at nominal 240 V its cold resistance calculates to roughly⢠22 âΊ (R = V²/P)and itsâ mechanical layout â˘and terminal spacing determine compatibility with oven brackets and⤠connector tabs. Degradation typically begins⢠with coil breaks, oxidation at terminalsor breakdown of the insulating sheath, each of which alters electrical behavior: partial open⣠circuits raise resistance and reduce heat output, insulation failure produces leakage to the chassis and can trip protective devicesand localized hotspots cause blistering or discoloration visible on the⢠element surface.
- Intermittent or no heat; multimeter shows open circuit at â¤the element terminals.
- Uneven cooking or â˘localized luminous spots; visible bubbling, warpingorâ dark scorch marks on the coil.
- Breaker trips or fuses blow when element is energized, indicating leakage or short to chassis.
- Measured terminal resistance âsubstantially higher than the âexpected range,suggesting poor terminal contact âŁor partial coil â˘failure.
Diagnosticâ tests begin with a de-energized visual inspection and progress to âelectrical checks: perform a continuity/resistance measurement with the element removed-anâ open indicates âa broken coil, while a resistance near the calculated value confirms continuity; measure resistance to⣠chassis or earth to detect insulation leakage (any low-ohm connection is a fault). Under load, measure current with a clamp meter and compute power (P â= â˘V Ă I); a 2600 W element at 240 V should draw about 10.8 A, so substantially lower current suggests a partial open or high contact resistance and higher current or nuisance tripping suggests a short. Use a megohmmeter for definitive insulation testing when availableand always isolate power and disconnect terminals before testing to avoid false readings⤠and ensure safety.
| Item | Description |
|---|---|
| Expected⢠cold resistance | ~20-25 Ί (calculated â˘R â 22 Ί for 2600 W⤠at 240 V) |
| Expected operating â˘current | ~10.8 A at 240 V (2600 W output) |
| Common failure modes | open coil, increased contact resistance, insulation-to-chassis leakage,⣠localized hotspots |
Compatibility, Replacement Considerationsand StepâbyâStep Installation âGuidelines for the 316442301 Coil Element
The 316442301 Frigidaire Oven 2600W 8â Coil Element isâ a resistive surface heating element â¤engineered to deliver approximately 2600 watts of heat at nominal household range supply. It is designed for an 8âinch opening and typically interfaces with the range via dual swiftâdisconnect terminals and a spring or clip mounting at the drip⤠pan. Measured cold resistance âshould be âon the order of V^2/P (240^2/2600 â 22 Ί), so â˘a technician confirming continuity can âexpect a resistance in that range; a completely open circuitâ or a dramatically lower value indicates a failed element or internal short.â Common failure âŁmodes include âŁopenâ coils fromâ broken internal windings,localized overheating from grease accumulation or wire⢠insulation⢠breakdown,and⣠terminal corrosion that compromises the electrical connection or causes erratic heating behavior under load.
When â˘replacing the element, confirm electrical and mechanical compatibility: matching wattage (2600 W), terminal style (straight orâ curled quickâdisconnect),⣠physical diameter (8 in)and âthe range control switch rating. If the existing⢠infinite switch isâ pitted⣠or rated below the element’s current,replace the switch to avoid premature failure. Practical installation steps for a safe and reliable replacement include verifying power isolation, documenting wire⣠locations, testing continuityand observing a controlled powerâup to verify even heating. For exmaple,replacing the element in a Frigidaire⤠range âŁtypically also requires inspection of the⤠drip pan and mounting clips; warped pans or broken clips canâ misposition the coil âand create hot spots even when the element itself is functional.
- Disconnect power at the breaker and verify no voltage at theâ element with a multimeter.
- Remove surface elements or glass cooktop components as required to access the coil and drip pan.
- Note or photograph terminal wiring positions,than disconnect the quickâdisconnects from the old element.
- Remove mounting clips,lift out the old element,and inspect the drip pan and switch terminal for corrosion or arcing damage.
- Install the new element ensuring⢠correct terminal orientation and secure mounting; replace clips or drip pan if deformed.
- Verify⣠cold continuity of the new element (expected â 22 Ί),reassemble,restoreâ power,and perform a lowâpower functional test to check for even heating and proper control response.
| Item | Description |
|---|---|
| Part | 316442301 Frigidaire Oven 2600W 8 Coil Element |
| Wattage | 2600 W |
| Nominal Voltage | 240 V (verify supply) |
| Cold Resistance | Approximately 22â Ί (240²/2600) |
| Physical Size | 8âinch coil (measure for fit) |
| Terminal Type | Dual quickâdisconnect (verify straight vs.curled) |
Q&A
What is the⣠316442301 â¤Frigidaire Oven 2600W⤠8 coil element?
It is an OEM replacement bake element for Frigidaire electricâ ovens, rated at 2600 watts. The part is a coiled heating element (commonly called an “8âinch” or “8⤠coil”â bake element) that produces heat when⢠240 V is applied. The wattage rating describes the heat output at âthe rated âvoltage and helps determine âbake⢠time â˘and performance.
How do I⢠know if this element is compatible with my oven model?
compatibility is determined by your oven’sâ model numberâ and the OEM part number. Check the âowner’s manual or the parts diagram âŁfor your specific Frigidaire modelor search the model number against the part number 316442301 on⣠the manufacturer orâ authorized parts websites. Alsoâ compare mounting style, terminal type and physical dimensions⣠to ensureâ a proper fit.
What are the electrical specifications (voltage/resistance) âŁfor this 2600W element?
the element is rated for typical household electric ranges using 240 volts. At 240 V the expected cold (roomâ temperature) resistance is approximately R⤠= â˘V²/P â 240² / 2600 â˘â 22 ohms.Resistance can vary with temperature and manufacturing âŁtolerance, so a value near 22 Ί â¤indicates the element is likely good.
How do I test âthe element to see if⢠it is indeed bad?
Turn off power at the breaker and remove the element safely. use a multimeter: check for continuity across the two terminals (shouldâ read⣠continuity and ~22 Ί at room temp).Also check there is no continuity between either âterminal and the⣠metal chassis/ground (thatâ would indicate anâ insulation short).If the element is open (infinite⣠resistance) or shows a short to ground,it needs replacing.
What are common symptoms that the bake element is failing?
typical signs include: â˘oven not heating or taking much longer to heat, uneven baking or hot spots, visible breaks or blisters in the element, arcing or sparking when in useor âa burnt/metallic âsmell. If the breakerâ trips when the oven⣠element is turned on, that can also indicate a shorted element.
How âdo I replace the â¤316442301 element safely?
Turn off power at the main breaker. remove oven racks and access the element from inside the oven (or from the rear, depending on model). Remove mounting screws or retainers,carefully pull the⤠elementâ forward âŁto expose terminals,disconnectâ the wires (note terminal positions),install âŁthe new element by reconnecting wires and re-seating mounting hardware and⣠any⣠insulating â˘grommet or bushing,restore covers/racks,then turn âŁpower back on and test. Always follow the oven manufacturer’s service⣠instructions and wear gloves/eye protection.
What can cause this element to fail â˘prematurely,and how can I prevent it?
Causes include â˘spillage and corrosion,frequent â˘heavy use with high temperatures,physical damage from impact,electrical faults (voltage spikes or shorting),and overheating due to restricted airflow. Prevention: keep the oven interior clean, â˘avoid âheavy impacts to the âelement, ensure correct â˘wiring and functioning â¤controls,⢠and fix⣠spills promptly to prevent corrosion.
Where should I buy a replacement and are there warranty considerations?
Buy from Frigidaire authorized dealers, the manufacturer’s partsâ siteor reputable appliance parts retailers to ensure you get the correct OEM part (316442301) or an approved equivalent.â Check the seller’s return policy and any manufacturer âŁwarranty. If â¤your oven is under appliance warranty,contact Frigidaire service first â˘to avoid⢠voiding coverage by using thirdâpartyâ installersâ or parts.
Wrapping Up
The 316442301 Frigidaire Oven 2600W 8 Coil⢠Element functions as a primary heating component in compatible Frigidaire ovens, âproviding the consistent, high-output⢠heat required for bakingâ and broiling. Its â¤design â¤and wattage directly⢠influence temperature stability, cooking performanceand overall⣠appliance efficiency, makingâ it a critical part for achievingâ reliable, predictable results in everyday âuse.
when the element degrades or fails, symptoms such as uneven heating, longer cook times,⤠or intermittent operation⤠can ariseand unresolved issues may affect energy consumption or present safetyâ concerns. Accurate diagnosis-combining visual inspection with appropriateâ electrical testing-helps identify whether⣠the element is the underlying cause or whether another component is âresponsible.
Timely replacement with the âcorrect 316442301 2600Wâ coil element restores intended performance and reduces the risk of further damage.â To ensure safety and proper â¤operation, replacement should follow manufacturer specifications and, when necessary, be performed or verified by a qualified service technician. Proper maintenance and correct âpart selection help maintain oven reliability, safetyand cooking âquality over the long term.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
