WE25M87 GE Washer LP Conversion Kit is a parts kit designed to modify the fuel-delivery components ofâ compatible⢠GE laundryâ appliances soâ they can operate on⢠liquid propane⢠(LP)⤠ratherâ thanâ the factory-set âfuel type. As a conversion kit, it âtypically â˘contains sized orifices, pressure orifices or spacers,â gaskets or fittingsand labelingâ or âŁinstructions required â˘to change the⤠appliance’s gas flow characteristics; its purpose is â¤to ensure⤠correct fuel metering and safe combustion after a fuel-type âchange.
Inside an â˘appliance, âthe conversion â¤kit modifiesâ theâ fuel metering subsystem and interfaces⢠directly⢠with the gas valve, burner orâ heater assemblyand any associated pressure-regulation components and safety devices (igniter/ignition module, flame sensing, thermocouplesand venting). âŁproperly matched orifice sizes and âregulator adjustments âŁmaintain the required volumetric flow â¤and pressure for LPand the â¤conversion therefore affects combustion efficiency, temperature âcontroland safety interlocks. Because gas chemistry⢠and pressures differ between⢠natural gasâ and LP,⢠theâ kit’s components and installation âprocedure are â¤critical âfor â¤maintaining safe flame characteristics, avoiding incomplete combustionand ensuring theâ appliance control⣠systems receive â˘expected thermal feedback.
In this article readers will find a technical overview of the WE25M87â kit’s function, the specific âsystems âŁit interacts withand how to verify model compatibility. The article will cover⣠common âfailure symptoms that indicate incorrect conversion âŁor degraded components (such as weak heat output, soot, irregular ignitionor⤠gas odor), recommended troubleshooting âchecks (pressureâ testingorifice âŁverification, leak testing,â and âŁinspection of ignition and sensing â¤circuits)and practical replacement considerations⢠including parts inspection, torque and sealing âpractices, labeling,â and âŁregulatory/safety steps â¤that should be followed.Theâ guidance âis intended â˘for technicians and engineers familiar with gas appliance servicing; where appropriate, the article will emphasizeâ that â˘conversions should be performed in accordance with local codes⣠and manufacturer âŁinstructions and by qualified personnel.
Table of Contents
- Function and Role of⤠the LP conversion Assembly: Pressureâ regulation, Orifice sizing,⣠and Safety Interfaces
- Howâ the WE25M87 âGE Washer LP⤠Conversion Kitâ Works Inside the Gas Valve and Electronic âcontrol system
- Common Failure â˘Symptoms and Diagnostic⤠Indicators â¤ofâ LP Conversion â˘Components
- Compatibility, replacement Considerations, Installation âŁProceduresand Troubleshooting Diagnostics for LP Conversion âŁKits
- Q&A
- In Retrospect
Function and Role of the LP Conversion Assembly: Pressure â˘Regulation, Orifice Sizing,â and Safety Interfaces
the WE25M87 GE Washer⣠LP Conversion Kit â˘reconfigures âthe â¤gas delivery path so the⣠appliance will⣠operate safely and efficientlyâ on â¤propaneâ (LP) rather â¤of âŁnatural gas. The conversionâ assembly replaces the factory â˘orifices with smaller jets âand modifies theâ regulator âseatingâ to accommodate theâ higher ânominal pressure âand different density of LP fuel; the regulator controls downstream âmanifold⣠pressure while the orifice âsizing determines the volumetric flow and âtherefore the burner heat âoutput. In practice, the kit â˘balances pressure â˘regulation and flow restriction to âmaintain correct âŁair-fuel ratio atâ each burner portand a âcorrect⣠installation requires verification ofâ manifold pressure, leak-free fittingsand observation of flame shape and stability under typical cycles.
The assembly also integrates with⣠the washer’s safety â˘interfaces so that existing valves, flame-sensing devices, âand electronic⢠controls continue to function without modification. Technicians should confirm that â¤the conversion componentsâ are physically âŁcompatible withâ the valve body and use the specified jet sizes⤠supplied with the â¤kit; after conversion,check that burner âignitionâ timing,flame lift,and emissions remain within manufacturer serviceâ limits. Typical âpost-conversion⤠checks include measuring âŁmanifold pressureâ under steady-state âconditions, confirming no persistent yellow tippingâ or â¤flameout during high-demand cycles, âand testing safety⣠shutoffs; these steps ensure that pressureâ regulationorifice sizingand safety interlocks work âŁtogether to preserve safe combustion and appliance âreliability.
- Included features: orifice jets sized for LP, âregulatorâ adjustment â¤or insert, âŁgaskets/sealsand conversion labeling for service⣠records.
| Item | Description |
|---|---|
| Pressure⢠regulator | Reduces and stabilizes âŁinlet pressure to the manifold so downstream valves âsee â˘appropriate set pressureâ for LP⤠operation. |
| Orifice âinsert | Smaller âdiameter jets⢠limit volumetric flow to match propane energy density and âmaintain correctâ burner⢠heat â¤output. |
| Safety interfaces | Mechanical and electrical â˘interfaces (valve seats, flame sensor positioning) that must remain compatible⢠to allow normal safety âŁshutdown behavior. |
How the WE25M87 GE Washer LP âŁConversion Kit Works Inside the Gas Valve and Electronic Control System
The⣠WE25M87 GE Washer⤠LP Conversion Kit modifies the âgas delivery path â˘inside the appliance’s gas valve âassembly so the burner receives the correct fuel quantity and pressure when using liquidâ petroleum (LP) rather of natural â¤gas. Mechanically, the kit provides a smaller orifice/jet âand âan appropriate pressure-regulating â˘insert or shim that⤠changes the⤠effective cross-sectional flow area and the valve’s internal pressure reference. Electrically,the â˘solenoid â˘coils and âŁthe âelectronic âcontrol board continue âŁto operate using the same⢠control signals; the conversion kit does not alter coil voltage or the valve⢠actuation method. Technicians must verify that the kit matches the âŁexisting valve model and coil voltage to ensure âmechanical compatibility â¤and safe operation under the control board’s timing â˘and interlock sequences.
In practice, installing the kit changes⢠manifold âflow characteristics âand thus requiresâ post-conversion functional checks: measure manifold âpressure under a call forâ heat with⣠a â˘manometer, confirm stable flame shape and sensor feedbackand perform leak and combustion tests per service specifications. The conversion can⤠affect burner temperature rise and the⢠control’s⢠thermal response, so controls âŁwith adjustable setpoints or timed purge sequences may need â¤verification after conversion. Typical⤠items âincluded in the⣠kit and checks to run during service⤠are listed below.
- Kit contents and their roles: orifice/jet (flow restriction), regulator⣠insert or shim (pressure adjustment)and gaskets/fasteners.
- Compatibility checks: verify gas valve model,⤠solenoid⢠voltage, â˘and control board interlock requirementsâ before installation.
- Post-installation tests: manifold pressure measurement, flame stability/appearance, control âdiagnosticsand leakâ testing.
| item | Description |
|---|---|
| Orifice/Jet | Reduces bore diameter to limit volumetric fuel flowâ for LP⤠fuel⣠density. |
| Regulator Insert/Shim | Adjusts internalâ valve spring/reference to â¤achieve the manufacturer-specified manifold pressure. |
| Gasket/Hardware | Seals valve passages and secures conversion components without⣠interfering with solenoid movement. |
Common Failure Symptoms and Diagnostic Indicators of LP Conversion Components
The WE25M87 âGE âWasher âLP Conversion Kit adapts a gas-fed heating â¤assembly from natural gas to liquid propane by changing the effective orifice size and adjustingâ the regulator characteristics so⣠the â˘burner receives the correct fuel flow and pressure. Conversion⤠components âŁalter âthe burner/valve interface-smallerâ orifices,â alternateâ regulator springs,â and calibrated fittings-so that combustion behavior⢠(flame shape, â¤heat outputand â˘ignition âŁtiming) matches the properties of propane. Compatibility dependsâ on âthe appliance’s gas valve model and burner geometry; a⣠physical fit and matching thread sizes â¤are⤠requiredand the same conversion parts can âŁproduce different results âon âburners with⤠differentâ port spacing âorâ air shutter designs. Practical evaluation after â˘conversion must include visual⤠flame âinspection andâ pressure verification to confirm the kit is⤠performing asâ intended rather â¤than relying⣠on part fit alone.
- Reduced or uneven â¤heat output during cycles
- Delayed â˘ignition or extended sparking before â¤flame establishes
- Yellow, liftingor sooty flame indicating incomplete combustion
- Gas odor⢠or unusual cycling of âthe gas valve
- Repeated⢠tripping of flame-detection or⣠high-limit safety devices
| item | Description |
|---|---|
| Flame â¤color | Blue and steady indicates correct mixture; persistent âyellow⤠or soot âŁsuggests too ârich mixture or⢠insufficient primary air. |
| Manifold pressure | Measuredâ with aâ manometer â˘against the service⣠spec in the conversion âinstructions; low pressure â¤producesâ weak flame and⣠delayed ignition. |
Diagnosing failures combines simple observations with âa few measurements: inspect⢠flame color âand âpattern, verify orifice size marking against⣠the kit âspecificationand measure manifold pressure while the burner is operating.If ignition is delayed, check for partially blocked⢠orifices or debris in the pilot/igniter path and⤠confirm theâ valve âis seating electrically (verify continuity or â¤coil resistance per service data). A practical example: a⣠steady blue flame at nominal pressure but reducedâ heat output usually points to incorrect orifice sizing or⢠excessive⣠primary air, while aâ yellow sooting flame at normal pressure most â˘frequently⤠enough indicates a rich mixture from oversizedâ orificesâ or incorrect regulator setting. Use âthe appliance service manual and theâ kit’s⤠documentation âfor the specific valve resistance and⤠pressure⤠values when interpreting measurements. â¤
Compatibility, Replacement Considerations, Installation Proceduresand Troubleshooting Diagnostics for LP Conversion Kits
The WE25M87 GE Washer LP Conversion⢠Kit contains the gas orifices, fittingsand any regulator adjustments required to convert aâ gas-fired â˘component from natural âgas to liquid propane â˘(LP).in â˘practice the âkit replaces the larger natural-gas orifices with smaller â˘LPâ orifices and provides the correct regulator setting â¤so manifold âpressure and fuel/air â˘ratio are appropriate for propane’s higher energy density.Compatibility âis steadfast by â¤theâ appliance’sâ gas valve type, â¤burner geometryand mounting provisions; confirm the washer’s model and âŁserial number against the âkit’s submission list before installation. Whenâ selectingâ a replacement, â¤match the valve family and pilot/ignition style rather than ârelying on superficialâ similarities between modelsand avoid modifying⤠the gas valve orifice beyond the manufacturer-supplied âcomponents.
Installation â¤requires⢠isolation of gas and electrical supplies,â replacement⢠ofâ the orifice âand any regulator springâ or cap included in the kitand verification of âinlet andâ manifold⣠pressures with a calibrated manometer. After reassembly perform a leak check on all connections and observe flame shape and stability under steady state and cycling conditions; âLP flames are typicallyâ shorter and must âbe predominantly blue with only⢠a small âyellow â˘tip. Common troubleshootingâ diagnostics include verifying manifold pressure (natural gas â 3.5⤠inches âŁWC vs. LP â 10 inches WC as a reference), checkingâ for âsoot or yellow-tipped flames whichâ indicate rich mixture or restricted air, inspecting orifice seating âand alignmentand confirmingâ that the⤠ignition â˘system producesâ a reliable⣠spark or pilot. If heatingâ is low or combustion noise â¤is present, re-check orifice size andâ regulator setting and replace âany worn gaskets or seals that coudl cause âpressure loss.
- Symptoms to test: weak heat â˘output, yellow/sooty flame, noisy burner, intermittent ignition.
- Fast checks: leak test with soapy âsolution, measure âmanifold âand inlet pressure with manometer, verify⤠correct orifice part and orientation.
- Adjustments: install supplied â˘regulator spring/cap per kit âinstructions andâ re-check manifold â˘pressure â˘under load.
- When to replace components: cracked orifice, damaged valve seator regulator that cannot â˘hold specified pressure.
| Item | Description |
|---|---|
| WE25M87 | LP conversion components â˘(orifices, fittings, regulator adjustment) for applicable GE âunits⤠– verify model/serial compatibility. |
| Typical LP manifold â˘pressure | Approximately 10 inches WC (use calibrated⣠manometer âto confirm and adjust). |
| Key inspection â¤points | Orifice size â˘and seating, regulator⣠spring/cap, gas âconnection integrity, ignition/pilot âoperation. |
Q&A
Is the GE WE25M87â a model that uses an LP conversion kit?
First confirm whether yourâ WE25M87 is âactually aâ gas appliance. Many WE-series GE models are âwashers (whichâ are electric and⣠do not use gas).⢠LP conversion kits â˘onlyâ apply to âgas-fired appliancesâ (for âexample gas dryers). If your unit is â˘a gas⣠model, consult the appliance rating plate and the owner/service manual to verify whether the manufacturer lists an âLP⣠(propane) conversion kit âfor âthat specific model.
What⤠typically âŁcomes inâ an LP conversion⢠kit for a GE gas appliance?
A âmanufacturer-approved LP conversion â¤kit usually includes: burner orifices sized for propane,â any needed regulator âadjustment parts or â¤replacement regulator components, mounting hardware, conversion instructionsand a permanent conversion label/sticker â¤to âapply to the appliance. âŁContents vary by â˘model, soâ always use the kit specified by GE for that exact âmodel number.
Can I â˘install the LP conversion kit myselfor do Iâ need a technician?
Conversion must be done by a⢠qualified service technician or installer â˘who understands⤠gasâ appliance work and local âcodes. Improper conversion⤠can⤠create a fire, explosion or carbon âŁmonoxide hazard. âmany manufacturers (including GE) and local regulations require a trained service âtechnician âŁto perform the âconversion â¤and sign offâ on⤠it.
Will converting to LP void my warranty?
If the conversion is performed according⤠to the manufacturer’s instructions and with anâ official GE conversion kit, âit is typically acceptable. However, unauthorized modifications or use of nonâOEM parts can void the warranty. Always check GE’s warranty terms and have the conversion âŁdocumented by âŁthe technician.
What safety checks should be performed after completing the⣠LP⤠conversion?
After conversion the technician should: verify correct manifold pressure per GE specifications (LP manifold pressure is higher than⤠natural⣠gas and the manual âŁwill list the exact value), inspect⣠flame appearance and stability, performâ a gas leak test âon all fittings (soap solution or electronicâ leak detector), confirm âproper operation of ignition/pilot and safety controlsand apply the conversionâ label.It’s âalso good practice⤠to monitor for⢠proper combustion (no unusual odors; consider COâ testing⤠if concerned).
Do I need⤠a different gas regulator or supply line for propane?
Many â˘appliances require regulator â˘adjustment or replacement whenâ converting to â˘LP as propane operates at a different â¤pressure than natural⢠gas. The conversion kit will specify if a regulator component mustâ be changed. Also ensure thatâ the external gas supply andâ hose are ârated âŁfor LP/propane âand that fittings and piping meet local code requirements.
How do I recognize a correctâ LP flame and properâ operation after⢠conversion?
A⣠properly â¤adjusted LP flame is mostly âblue with âsmall, clean yellow/orange tips; âŁit should be steady and â¤not liftingâ or⤠producing excessive yellow/orange sooting. The appliance should âcycle and heat as⣠specified in the manual without gas odorsâ or popping noises. If the flame âis large, âsmokyor there’s a persistent smell of gas, â˘turn the appliance off and call a technician.
what paperworkâ or labeling should be left on the appliance after conversion?
The technician âshould attach⢠the conversion label provided in theâ kit⢠to the rating plate âor â˘another âvisible location, note the new gas type and any â˘regulator settings, âŁand provide a record of the work performed. keep the conversion instructions, â¤receipts and any updated manualsâ for warranty and âinspection purposes.
In Retrospect
the WE25M87 GE Washer LP Conversion Kit serves an significant role in adapting compatible GE appliances to operate on liquid propane (LP) âfuel.â By providing the correct orifices,regulators and⤠installation components specified for the model,the kit âhelps maintain proper fuel â¤delivery,combustion characteristics and overall appliance performance when switching fuel types. â¤Correct use of the kit supports safeâ operation, energy efficiency and compliance with the â˘manufacturer’s design parameters.
Accurate âdiagnosisâ of fuel-related âsymptoms and⤠confirmation âofâ compatibility with the appliance model âŁare essential before attempting a conversion. If components are worn, damaged orâ incorrectâ for the âspecificâ appliance, â˘replacement with the correct WE25M87 kit or equivalent factory-approved âparts is warrantedâ to prevent improper⣠combustion, reliability problems âor safety risks. âRelying on documented âtroubleshooting procedures and, where applicable, assistance from qualified service personnel reduces the likelihood of errors during diagnosis and repair.
When installation or âreplacement is required, following the manufacturer’sâ instructions, using the exact approvedâ kit for⤠the appliance model, â¤and completing post-installation testing âŁensures âŁthe conversion performs as⣠intended.Properâ installation and recordkeeping preserve⤠appliance reliability, help âmaintain any applicable warranties,â and provide reassurance that âŁthe appliance âŁwill operate safely and âefficiently on LP fuel.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
