WB16K10026 GE Oven Range Stove Cooktop Double Burner is a replaceable cooktop heating element designed for use in GEâ electric ranges. As a double burner (dual-element) assembly, it provides two concentric heating zones on a single surface element to accommodateâ different cookware sizes and heat requirements. The component is a direct â˘replacement â˘part intended to mount into the âŁcooktop surface â˘and connect to the âappliance’s power and control terminals.
Inside the appliance,the double burner converts electrical energy â˘into heat and interfaces with the cooktop control system,including the âinfinite switch (or⢠electronic control),terminal block,wiring harness,and any associated indicator circuitry. Mechanically it interacts with the cooktop âŁsurface (porcelain or glass), âburner âsupportsand cookware, while electrically it must match the range’s voltage and wattage requirements. Proper electrical connection, thermal contact with cookwareand âintact insulation are required for âsafe, predictable operation; failures can affect cooking performance and safety systems.
In this article you will find a technical overview of the WB16K10026’s function and construction, how to determine compatibility with specific GE range models (terminal type, mounting, voltage/wattage and physical dimensions), common failure symptoms (no heat,â intermittent⤠operation, uneven heating, arcing, visible element damage),⢠step-by-step troubleshooting checks (continuity and voltage tests, inspection of wiring and switchesand isolating control faults)and âŁpractical replacement considerations (correct part matching, safe power isolation, âŁterminal connectionsand basic â¤installation tips). The information is â˘presented to aid technicians,engineers,and appliance owners in diagnosing issues and making informed decisions âabout repair or replacement without assuming âadvanced diagnostic equipment.
Table of Contents
- Functional Role and Performanceâ Parameters of the Cooktop Double Burnerâ Assembly
- Internal Design and Operation of⣠the WB16K10026 GE Oven Range Stove Cooktop Double Burner
- Failure Modesâ and Diagnostic Symptoms of the Doubleâ Burner Assembly
- Model Compatibility, Replacement Procedures, Installation Requirements and Troubleshooting
- Q&A
- Wrapping Up
Functional Role and Performance Parameters of the Cooktop Double Burner Assembly
WB16K10026 GE Oven Range Stove Cooktop Double Burner is an OEM dual-ring surface element assembly⢠that provides twoâ concentric heating zones toâ support both low-powerâ simmering and high-power⣠boiling on compatible GE electric ranges.Functionally, the double burner concentrates âŁheat transfer through an inner and outerâ resistive element that can be energized independently or together via the cooktop control. The assembly’s mechanicalâ interface (mounting flange and terminal clips) and electrical characteristics determine fit and operability; installers âshould match element diameter, terminal styleand rated voltage toâ the host cooktop to ensure reliable connection and heat output.
Performance is defined by how the inner and outer circuits share current and by the thermal âresponse of the cooktop surface. In practical service terms this means âthe part will exhibit two distinct resistance paths and predictable warm-up behavior: the inner ring reaches low-to-medium output for simmer tasks, while âenergizing both rings increases total wattage for rapid boiling. Technicians â˘diagnose failures by inspecting the element for physical breaks or corrosion, verifying continuity acrossâ the âinner/outer terminalsand confirming the control switch applies appropriate voltage. when replacing the assembly, confirm âŁmodel compatibility and measure terminal spacing and âelement diameter â¤to avoid mismatches that affect heat distribution or mounting â¤stability.
- Dual-zone heating (inner/outerâ rings) for variable power output
- OEM mounting and terminal styles to match specific GE range models
- Service checks: visual damage,continuity test,and terminal voltage verification
| Item | Description |
|---|---|
| Function | Provides two concentric heating â˘zones allowing self-reliant orâ combined operation for simmer and boil settings |
| Interface | Mounting flange and spade/clip terminals;⢠must âŁmatch cooktop spacing and connector type |
| Behavior | Separate resistance paths⤠for inner/outer rings; combined âoperation increases total heat output |
Internal Design and Operation of the WB16K10026 GE Oven Range Stove Cooktop Double Burner
The WB16K10026 GE Oven Range Stove Cooktop Double Burner â˘is a dual-zone resistive heating element constructed as two concentric circuits housed within a metal sheath and embedded insulating filler. Each circuit terminates at insulated studs that connect to the⤠cooktop wiring âŁharness and the infinite switch; energizing one or both circuits changes the effective surface power. Heat is generated by Joule heating in the â¤internal⢠resistance ribbon or coilâ and conducted through the sheath to the cooktop surface and cookware.â The dual-ring arrangement provides a distinct thermal response⤠for low-power simmering on â˘the inner zone versus higher-power boiling when both zones are energizedand the assembly’s thermal mass and sheath materials determine⣠warm-up and cooldown rates as well as heat-spread characteristics across pans of different sizes.
Technically, the part behaves as two series/parallel resistive elements controlled by the range’s selector switch and protected by the oven’s grounding and safety circuits;⣠common failure modes include an open circuit in one⤠ring, short-to-ground from â¤insulation breakdownand terminal arcing from loose connections.â For service, a technician should verify continuity across each terminal⤠pair, inspect insulation at the stud mountsand confirm mechanical fit and terminal type before replacement. Practical compatibility checks include âmatching the element’s mounting âflange, terminal spacing and styleand rated wattage/voltage to the appliance’s service specifications; using⢠the â˘original part number ensures correct interaction with the range’s controls and reduces risk of overloading the infinite switch.
- dual-zone function: â˘inner and outer circuits for variable heat â˘control
- Connection type: insulated terminal studs compatible with standard range harnesses
- Common faults: open circuit, short-to-ground, terminal âarcing, warped flange
- Service⢠checks: visual inspection, continuity test, fit and rating confirmation
| Item | Description |
|---|---|
| Element type | Concentric dual-zone metal-sheathed⢠resistive element |
| Connections | Insulated terminal studs; verify harness compatibility |
| Control interface | Designed for⢠use with standard range infinite switches (one or two circuits) |
| Failure â¤indicators | No⢠heat on one zone, intermittent heating, visible terminal damage |
Failure Modes andâ diagnostic Symptoms of the Double âBurner Assembly
The WB16K10026 GE Oven Range Stove âŁCooktop Double Burner is a dual-zone surface heating element assembly âthat provides two concentric heating circuits so the user or the range âinfinite switch can selectâ inner, outeror fullâsurface⢠heat. Functionally it⣠must present continuity between its âŁtwo load terminals âwhile remaining⤠electrically isolated from the appliance chassis; failure modes include an âŁopen coil, a short to groundâ from coil insulation breakdown,â or terminal/plug damage that causes intermittent contact. Compatibility â¤with a given GE range is âŁpersistent by terminal configuration, element diameterand mounting style, so technicians should confirm the WB16K10026 part number and inspect the terminal tabs and bracket before replacement to ensure proper electrical and mechanical fitment.
Typical diagnostic symptoms are readily correlated to specific faults and can be confirmed with a âvisual inspection and simple electrical tests: measure continuity between element terminals, check for resistance to chassis (insulation), observe for visible breaks, discolorationor burned terminalsand confirm correct line voltage at the element connector while⣠the control calls for heat. practical troubleshooting sequence: âisolate power, visually inspect element and receptacle, perform a continuity/ohm check, wiggle the element while monitoring continuity for intermittent faults, then test the âŁinfinite switch and terminal block if âthe element tests good. âBelow are common â¤symptoms to watch for and a compact reference mapping likely causes to diagnostic checks.
- No heat at any setting -⤠open circuit within⢠the element or failed connection at terminal.
- Reduced or uneven heat – partial coil break, degraded contactor inner/outer coil separation.
- Intermittent â˘operation or arcing – loose terminal, burned receptacleor insulation breakdown.
- Tripping breakerâ or sparking – short to chassis âor phase-to-phase⣠short; dangerous and requires immediate isolation.
| Item | Description |
|---|---|
| Open element | Multimeter shows infinite resistance between load terminals; element must be replaced. |
| Short⣠to ground | Resistance between either terminal and âchassis is very low; âindicates insulation failure and poses a trip/safety â¤risk. |
| Terminal/receptacle âdamage | Visible melting or arcing; intermittent continuity when manipulated – repair or replace connector and element as appropriate. |
Model Compatibility, Replacement Procedures, Installation Requirements and Troubleshooting
The⢠WB16K10026 GE Oven Range Stove Cooktop Double Burner functions as a direct-replacement surface heating element for compatible GE ranges and cooktops; confirm fit by matching the part number, terminal layoutandâ mounting tab spacing to the original element before ordering. This element âis a resistive heating coil terminated at a two- or three-prong connector that interfaces with the cooktop terminal block or wire harness. Compatibility depends on⤠physical dimensions, terminal⣠type (plug-in or screw terminal)and the appliance’s supply (nominal 240 VAC for most electric ranges). Technicians should verify the stove modelâ and the rangeâ serial/model plate and compare measured cold resistance to OEM specificationsâ to confirm the correct wattage class and to avoid mismatched power and heat distribution that can cause uneven cookingâ or premature failure.
Replacement and troubleshooting follow a safety-frist, test-and-verify workflow: de-energizeâ the appliance at the breaker, remove the cooktop or control panel⤠to access the element terminals, note wiring orientation, âdisconnect the elementand mechanically replace it ensuring secure mounting and correct terminal engagement. Typical failure modes include open circuit (no continuity), intermittent connection at âthe terminal blockand localized hot spots from damaged insulation; use a multimeter to check continuity and resistanceand inspect connectors⤠for corrosionâ or loose fasteners. After replacement tighten mounting hardware to factory torque where specified,restore power,and perform a heat-up test atâ low and high settings to confirm even ramping⤠and stable âoperation.
- Pre-checks: verify part number, terminal typeand mounting spacing; measure cold resistance to estimate wattage.
- Replacement steps: cut power, remove âŁcooktop access, label âwires, disconnect andâ replace element, reassemble, test.
- Common symptoms: no heat (open element),intermittent heating (loose/oxidized âterminal),uneven heat (partial coil damage or⤠wrong wattage).
| Item | Description |
|---|---|
| Part number | WB16K10026 – double surface heating element for⣠select GE ranges |
| Supply | Nominal 240 VACâ single-phase household range supply |
| Connector | Plug-in or screw terminal – match to original harness |
| Diagnostic | Multimeter continuity test; expect low ohms consistent with element wattage class |
Q&A
What is the WB16K10026 GE Oven Range Stove Cooktop Double Burner?
WB16K10026 is a GE replacement surface element assembly (a⤠twoâring or âdoubleââ radiant burner) used on electric smoothâtop or coil cooktops. It contains the inner and outer heating circuits (two concentric rings) that allow variable burner sizes and is installed under or on⤠the glass/ceramic surface or attached as a plugâin element on older âranges.
what are common symptoms that the WB16K10026 â¤element isâ failing?
Common symptoms include: the entire burner does not⢠heat at all, only the inner or outer ring heats,⢠the âburner cycles on/off irregularly, visible cracks or burn marks â¤on the element orâ its ceramic/insulating partsor⢠a tripped breaker when theâ burner is used.Intermittent heating can be caused by loose terminals or⢠a failing element or switch.
How can I test the WB16K10026 element⤠with a multimeter?
First disconnect power to the range. Remove⣠the â¤cooktop access panel and disconnect the element wires.measure continuity between the element terminals with an ohmmeter. A good heating element will show a⢠low resistance value in the tens⤠of ohms (not infinite). Exact resistance â¤depends on the element wattage; you can estimate âexpected R from R â¤= â¤V^2 / P (for example, at 240 V a 2,400 W element would be ~24 Ί). An âopen â(infinite) reading means the elementâ is burned out. Also check for short to ground by measuring resistance between each terminal âand the element chassis-there should be no continuity (very high resistance).
Can I replace the WB16K10026 myselfandâ what are⤠the basic â¤steps?
Yes, a competent DIYer can replace it, but always disconnect the range from power first (turn off the breaker or unplug). Typical⢠steps: remove the cooktop or⤠access panel, note and/or label wiring, disconnect element terminals, remove retaining clips or screws, lift out the âŁold element, install the new element, reconnect wires âŁsecurely, reassemble panelsand restore power. Follow the range’s service manual for modelâspecific instructions and wear safety gloves and eye protection. If unsure, hire a qualified appliance â¤technician.
Why does one ring of the double burner work â¤while the other does not?
Eachâ ring on a dual â¤burner is a separate heating circuit and can fail independently. If one ring is cold, possible causes are: an open element circuit (internal break in⢠the ring), a defective infinite switchâ or selector that supplies âthat ring, a loose or corroded⣠terminal/connectoror a wiring fault.Diagnose by visually inspecting terminals, testing element continuity for each ringand âtesting the corresponding infinite âŁswitch or wiring.
Do I need any other parts when replacing the⣠element (terminal block, clips, etc.)?
Not always, but inspect terminal insulators, wiring harness, clip/retaining hardwareand the terminal block during replacement.Corroded terminals or brittle insulating blocks are âcommon failure points andâ should be replaced if damaged. If the infinite switch was stressed or shows erratic behavior,consider replacing it too. Use OEM or manufacturerâapproved âreplacement âparts for best fit and safety.
How should I clean and care for âŁa cooktop with the WB16K10026 element?
Allow the surface to cool completely before cleaning.Use cleaners and pads recommended for your cooktop type-gentleâ cleaners for glass/ceramic tops, nonâabrasive pads for sealed elements on âŁcoil cooktops.Do not immerse the element assembly in water â¤or use harsh solvents on terminals. Avoid dragging heavy pots that can crack glass and avoid spills of sugary substances which can damage the element if heated ontoâ the surface.
How do â˘I confirm theâ WB16K10026 is the correct replacement for my GE range?
Confirm compatibility by checking your appliance model and serial number (usually on a tag behind the âŁoven door, under the cooktopor on the console) and crossâreferencing with GE’s parts â˘list⢠or âŁan authorized parts dealer. âDo not rely on physical appearance alone-verifyâ the part number and application to ensure correct terminals, mountingand wattage. If in doubt, provide your full range model number to the parts supplier or technician.
Wrapping Up
The WB16K10026 GE Oven Range Stoveâ Cooktop Double Burner serves as a essential â¤component of a range’s âheating system, directly affecting cooking performance, energy use and user safety. As a primary heat source on manny GE cooktops, its condition influences⢠temperature consistency, cook time accuracy and the overall reliability of the appliance; a worn orâ malfunctioning⢠burner can⤠lead to uneven heating, reduced efficiency and potential safety concerns if left unaddressed.
Timely and accurate diagnosis of burner issues-through inspection, continuity testing and verification of electrical connections-is importantâ to determine whether repair or full replacement is⤠appropriate. When replacement â¤is required, using the correct part⢠and âfollowing manufacturer guidelines or engaging a qualified service technician helps restore proper function,⤠maintain⤠safety standards and extend the service life of theâ range. proper diagnosisâ and replacement thus protect performance and provide the most dependable longâterm outcome for the appliance owner.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
