316203301 Frigidaire Oven â¤Broil element is a âresistive heating component designedâ for the broil function in compatible Frigidaire⣠electric ovensâ and ranges. Asâ a broil element it typically consistsâ of a sealed tubularâ resistance element with terminal connections that convert electrical energy into radiative and convective heat when energized; its construction and connectors are intended to meet the âelectrical and mounting requirements of the oven cavity where it âŁis installed.
Inside the appliance,the broil element provides the high,localized heat â¤at the top of the oven cavity used for broiling and finishing dishes,and it interfaces electrically and mechanically with the oven’s control system,selector switches or⢠electronic control board,and safetyâ devices such as thermal fusesâ or limitâ thermostats. Proper function depends on correct electrical supply to⣠the element, âreliable terminal and chassis mountingand coordination with temperature controls and user-selected modes; faults in any of these interacting systems can affect broil performance or cause the element to fail.
This article will explain the â¤element’s functionalâ principles and typical⤠specifications, describe how â¤to determine âcompatibility withâ specific⣠Frigidaire models, âidentify common failure symptoms (such as no broil heat, intermittent operation, visible breaksor⢠short circuits)and⢠provide systematic troubleshooting steps including â˘electrical checks and inspection of connectors and safety devices. It will also cover practical replacement considerations such as matching part number and âŁterminal type, safe disconnectionâ and reinstallation proceduresand verification steps to confirm proper operation after replacement.
Table of Contents
- function and Role of the broil Element in Oven Heat Production and Cooking Control
- How the 316203301 Frigidaire Oven Broil Element Integrates with Internal Wiring, Control Boardsand Thermostat Feedback
- Common Failure Symptoms and Diagnostic Indicators of Broil Element Degradation
- Replacement Considerations, Required Parts and StepâbyâStep Installation for the Broil element
- Q&A
- In Retrospect
Function and Role of the Broil Element in Oven Heat Production and Cooking control
The 316203301 Frigidaire⢠Oven Broil Element is a resistive heating component mounted at the top of the oven cavity that generates concentrated âradiant heat for broilingâ and surface⤠browning. Electrically, it converts line power into infrared radiation via a metal sheath containing a nickel-chromium resistance coil; that radiant⢠output is controlled by the oven’s control board or selector switch and any interposed relays or thermostats. The element isâ intended to operate atâ the appliance’s design voltage and must matchâ the oven’s terminal style, mounting flangeand physical length for proper compatibility-substituting a âvisually similar element that differs electrically or dimensionally can produce weak heating, uneven browningor safety faults.
In practical use,the broilâ element provides short-range,high-intensity heat: closer food placement increases searing and crust formation,while greater distance produces gentler browning. Typical failure modes are open circuit â˘(no heat), localized hotspots or blistering (coil insulation failure)and short-to-ground faults that can trip protection; these are diagnosed by visual inspection⣠and a multimeter continuity/resistance check at theâ disconnected terminals.⣠For service,verify the OEM⢠part number,confirm terminal type and mounting âalignment,disconnect power before handling,and⣠replace the element if resistance is out of expected range or if physical damage is present to restore predictable broiling performance and safe operation.
- No âheat at broil setting – check continuity between⢠element terminals.
- Uneven â˘browning or localized bright spots – inspect for blistering⣠or deformation.
- Circuit trips or⤠blown fuses – test for insulation failure or short to chassis.
| Item | Description |
|---|---|
| Location | Top interior wall of the oven cavity; âexposed to the air stream and positioned above food. |
| Primary function | Produce directional radiant heat for broiling and finishing surfaces. |
| Control âinterface | Operated by oven control board/selector and power relays; cycles according to user setting and safety thermostats. |
| Common service checks | Visual condition, terminal continuity, correct physical fit and secure connections. |
How the 316203301 Frigidaire oven Broil Element Integrates with internal Wiring, Control Boardsand Thermostat âŁFeedback
the 316203301 Frigidaire⢠Oven Broil Element is a simple resistive heater that⤠ties directly into⢠the oven’s highâvoltage circuit via theâ terminal block and the control board. The control board applies line voltage (typically 208-240 VAC in North American ranges) to the element by switching a relay âŁor solidâstate device when the user selects broil; the element itself has â˘no sensing electronics. Thermostat or temperatureâsensor feedback is provided by âthe oven’s temperature sensor/thermostat and the control board logic, not by the element. A technician diagnosing a failure will checkâ continuity across the âelement (a lowâohm reading consistent with its wattage), verify the presence of⢠line voltage at âŁthe element terminals only during a⢠broil calland inspect for⤠highâresistance or corroded terminal connections that can âcause poor heating or arcing.
- No broil heat while other functions work – suggests open element âor brokenâ connection at the terminal block.
- Element glows but cycles abnormally – possible control board modulation responding â˘to sensor input or a failing relay/triac.
- Tripped breaker or âshort to chassis – âindicates insulation failure or shorted element to âground.
- Uneven broiling – warped or partially burned element or bad connection causing uneven â˘current distribution.
- Visible arcing at terminals – replace element and repair wiring/terminals beforeâ restoring service.
| Item | Description |
|---|---|
| Nominal voltage | 208-240 VAC supply switched by control board |
| Typical resistance | Approximately 15-30 Ί â¤depending on element wattage (varies byâ model) |
| Typical power | ~2000-3500 W range for broil elements |
| Common failure modes | open circuit, short⣠to ground, terminal corrosion, mechanical deformation |
| Connector type | Insulated spade/fastâdisconnect terminals via oven terminal block |
For practical service, match replacement parts to the original element’s wattage, terminal orientationand mountingâ so the control âboard sees the intended electrical load; using a mismatched element can alter current draw âand heat profiles and may overload âswitching components.As the oven’s temperature sensor (commonly an NTC⣠probe) provides â¤feedback⤠to the control board, failures â˘in that sensor or its circuit can produce symptoms âthat mimic an element fault; isolate the element â¤by measuring resistance and verifying voltage under a controlled broil command to determine⣠whether to replace the element, repair wiring/terminals,⢠or â¤investigate⤠control board/sensor circuitry. Always disconnect mains power before performing continuity or insulation checks.
Common Failure Symptoms and âDiagnostic Indicators of Broil âElement Degradation
The 316203301 â¤Frigidaireâ Oven⤠Broil Element functions as the primary âradiant heater for the oven’sâ broil mode, converting electrical energy into infrared heat across the ovenâ cavity’sâ top. When the element degrades it typically displays reduced or uneven radiant output, localized cold spots, visible blistering or âdeformation of the sheathor⢠a hairline fracture âthat interrupts the internal heating âconductor. Compatibility checks – confirming terminal type (slip-on lugs vs. screw), overall length, mounting bracket positionand nominal wattage – are necessary before replacementâ to ensure the element mates correctly with the oven’s wiring and control ârelays; mismatched wattage can overload relays or change broil performance even if the physical fit is correct.
- Element does not glow or produces weak broil heat while other elements function normally.
- Uneven browning or localized hot/cold zones on broiled food.
- Visible surface damage: blistering, blister-induced breaksor exposed coil.
- Tripped breakers, blown fuses,â or arcing noises when broil is engaged (possible short or ground fault).
| Item | Description |
|---|---|
| Continuity test | Open circuit (no âcontinuity) indicates a broken internal conductor – replace âŁelement. |
| Insulation/ground leakage | Low resistance from element terminals to chassis indicates short to ground; element mustâ be replaced. |
| Supplyâ verification | Measured line voltage at element terminals during â˘broil confirms control/circuit is delivering power. |
For diagnostics, disconnect power before handling the element. Remove the element anchors â¤and perform a continuity check acrossâ the element â¤terminals; an open reading meansâ the internal heater is severed. Also check resistance from each terminal to âthe element sheath or oven chassis-expect very high (near infinite) resistance; measurable continuity to⢠chassis indicates⣠dielectric failure and risk of ground faults. â¤If continuityâ is present but â¤the element does not heat, measure⤠supply voltage at the element terminals with the broil function energized (restore power only for this measurement) to distinguish â¤between an⢠element â˘fault andâ a control/relay fault. Practical examples: if the element reads open but the oven control supplies correct voltage, the element is⢠defective; if the element has continuity but no heat and there is no supply voltage, investigate the selector switch, relayor âcontrol board and wiring harness compatibility with the replacement element.
Replacement Considerations, Required â˘Parts and â¤StepâbyâStep Installation for the Broil Element
Theâ broil element is the upper heating element that provides â¤intense radiant⤠heat for broiling and⢠finishing dishes; the 316203301 Frigidaire Oven Broil Element is a direct-replacement component⢠that restores that top-heat function in compatible Frigidaire ranges. Electrically, the element presents a low-resistance heater designed for the oven’s line voltage and should show continuity when measured with a multimeter; an open circuit or highlyâ elevated resistance indicates a failed element. Mechanically,the part mounts with two terminal studs and a mounting flange so proper âorientation and secure terminal connections are required for consistent heat⣠output and to avoid arcing. Typical failure modes are open circuits, âlocalized burn-throughor poor contact at the terminal studs, which manifest as inconsistent broil performance or no â¤glow at the element surface while the control calls for broil heat.
Before replacing the âŁelement confirm the âreplacement part number and terminal configuration match the ovenand prepare basic spares such as replacement terminal nuts or mounting âscrews if the originals are âŁcorroded; also have a multimeter and insulated tools available. Commonâ service steps are straightforward and can âbe completed by a technician or competent appliance owner after ensuring safe power isolation:
- Disconnect power at the breaker and verify with a voltage tester.
- Remove oven racks and access the element from the âoven interiorâ by removing the mounting screws or access⣠panel.
- Note wire positions,disconnect the terminal nuts,and âremove the old element from its⢠mounting flange.
- Install the new 316203301 âelement, âŁreattach wires to â¤the correct terminals, secure withâ new or inspected nutsand fasten the mounting âscrews.
- Restore power and perform a continuity check and short functional⢠broil test at âlow duration toâ verify correct operation.
| Item | Description |
|---|---|
| Part⢠number | 316203301 Frigidaire â˘Oven â¤Broil Element – direct-replacement heater with flange and two terminal studs |
| Electrical check | Continuity test with multimeter; open = replace. Inspect for signs of short âto chassis. |
| Required tools | Insulated nutâ driver, âmultimeter, screwdrivers, replacement terminal nuts/screws |
| compatibility note | Fits Frigidaire ovens with matching mounting flange and terminal spacing; consult model wiringâ diagram for confirmation. |
Q&A
What is the 316203301 Frigidaire âoven broilâ element and which ovens use it?
The 316203301 is an⢠OEM upper broil (top) heating element sold for many Frigidaire/Electrolux/Kenmore⣠ranges and wall ovens. it replaces the factory broil â¤element that provides directâ radiant heat from the top of the oven⢠cavity. Compatibility depends on the appliance model – always verify the appliance model number or the original part number âagainstâ the seller’s compatibility list before buying.
What âare common symptoms that the broil element needs replacing?
Typical symptoms include no broil heat (upper element staysâ cool), uneven or weak broiling, visibleâ damage suchâ as blistering, cracks,⣠breaks or exposed metal, sparking/arcing from the element when poweredand a persistent burning smell.If the elementâ shows visible âŁdamage or reads open on a continuity check, it should âbe replaced.
How do I test the 316203301 broil element with a multimeter?
first disconnect power to the appliance. â¤Remove the element’s electrical connections or disconnect⣠one terminal so you don’t backfeed through the circuit. Set a multimeterâ to continuity or the lowest ohms range. Place probes on the two element terminals: a good broil element normally shows a low resistance (typically a few ohms to a few tens â˘of ohms depending on wattage). An âinfinite or very high reading indicates an open (failed) â˘element.
canâ I replace the broil element myselfand⤠what safety steps should â˘I follow?
Yes, most owners can replace the element.Safety steps: disconnect power at the breaker (or unplug the range), let the oven â˘cool fully, wear gloves to protect against sharp edges, support the element while removing mounting screws,⢠note⢠terminal insulation and⢠orientationand reconnect terminals securely. After installation, restore power and test. If âyou’re unsure or uncomfortable with electrical⢠work, hire a qualified technician.
How long does replacing âthe 316203301 element typically take and what tools are needed?
Replacement usually takes 15-45 minutes. Common tools: screwdriver orâ nut driver to remove mounting screws, needle-nose pliers for terminalâ connectorsand a multimeter for testing. Keep the oven power off while⤠working and follow manufacturer instructions for your specific model.
What should I check to⣠make sure I’m⣠ordering the correct⤠replacementâ element?
verify the appliance model numberâ and cross-reference it with the part number.â Compare the old element’s part number, physical shape, âmountingâ bracket position, terminal style (flat blade, spade, âetc.), length and terminal spacing. Pictures and measurements â¤help ensure compatibility. Sellers’ compatibility lists⣠and OEM partsâ diagrams are useful for confirmation.
How much does a 316203301 broil element cost and is it covered by warranty?
Pricesâ vary by retailer butâ typical retail cost forâ a genuineâ OEM broil âelement is often in the $20-$80 range.â Warranty⣠coverageâ depends on where youâ buy it:⤠OEM sellers or appliance⤠manufacturers may offer a limited warranty (frequentlyâ enough 90 days to 1 year), while third-party sellers vary. Check the seller’s warranty and âŁreturn policy before purchase.
Is there any maintenance⤠or cleaning I should do to prolong the lifeâ of a broil element?
Keep the⢠element free of âŁheavy grease or food buildup⤠-⢠clean the âoven regularly and wipe the element only when it is completely cool. Avoid abrasive scrubbing that can damage the â¤element sheath or connections. If you notice persistent soiling that can’t be removedor any damage to the element surface or terminals, replacement is safer than⤠continued cleaning.
In Retrospect
The 316203301 Frigidaire oven broil â˘element âis a key heating component âdesigned to⣠produce⣠the high, concentrated heat required for broiling and finishing dishes.As an OEM-specified part for compatible Frigidaire ranges, itâ helps ensure consistent browning, searing and top-heat performance âwhile contributing to the overall reliability and efficiencyâ of the oven. â¤Properly functioning broil elements support predictable â¤cooking results and maintain the appliance’s intended performance characteristics.
Given its role,addressing symptoms of a âfailing broil⢠element-such as uneven heating,no heat during â˘broil cycles,visible damage,or tripped breakers-requires careful diagnosis to confirm the element is the source of the problem. When replacement is necessary, selecting the correct 316203301 part and following⢠manufacturer guidelines or consulting a qualified technician helps preserve safety, warranty âconsiderations and long-term appliance performance. Timely, accurate diagnosis and proper⢠replacement minimize further damage and restoreâ consistent oven operation.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
