A00099902 Frigidaire âDishwasher Door Latch is âa replaceable door latch and interlock assembly used⢠on Frigidaire dishwashers. it â¤isâ a âcombined mechanical and electrical component that securesâ the door in âthe closedâ position âand provides the⣠control system with aâ reliable signal âthat the⢠door is latched.â Physically the part consists of⢠the latch⢠striker âand mechanism, âmounting points to the door frame,⤠and one⣠or more âelectricalâ switch elements or connectors that communicate door â˘status âto the â˘applianceâ controlâ electronics.
Inside⣠the⤠appliance theâ latch performs two primary functions:⢠it creates â¤and⣠maintains the mechanical â¤seal and alignment required to prevent water escape,and⢠it closes⣠anâ electrical⢠circuit (the âdoor-closed/interlock signal) that⤠permits â˘the control board to start or continue a âŁwash cycle. âThe âlatchâ therefore interfaces directly with âŁthe door gasket and â¤hinge geometry, the control board and its safety logic,â and⢠the⣠user âdoor handle or actuator.A failing latch can allow the door âŁto open or leakor it âŁcan â¤prevent the â¤dishwasher from starting or can cause mid-cycleâ interruptions when the âŁcontrol detects an open-door condition.
In thisâ article you will â¤find a technical âoverview of the A00099902 â˘latch’s function and typical construction, guidance on model compatibility âŁand how to verifyâ whether âŁthe part⤠is appropriate for⣠a given Frigidaire âunit, âŁcommon failure⣠symptoms to⢠recognize, step-by-stepâ troubleshooting methods (mechanical inspection,⣠continuity â˘and voltage checks, alignment and seal verification)and âpractical considerations for âreplacement including removal/installation access, connector and âŁmounting âŁdetails,â and safety⢠precautions.â The intent is â˘to provide technicians, engineersand appliance owners with the information needed to â˘diagnose â˘latch-related problems andâ make âinformed âŁdecisions⢠when ârepairing⤠or replacing the component.
Table of â˘Contents
- Functional role and Mechanical Requirements âof the Dishwasher â˘Door Latch Assembly
- How the A00099902 Frigidaire Dishwasher âDoor latch Integrates â˘with Interlock âswitches,â Control Circuits,â and Door Actuationâ Mechanisms
- Common Failure Symptoms and âŁDiagnostic âIndicators for âDoor latch âMalfunction (mechanical jamming, electrical faults,⢠and water ingress)
- Replacement Considerations and â¤Installation Procedure â˘for Compatible Frigidaire Models
- Q&A
- To⣠Conclude
Functional Role and Mechanical⤠Requirements of the⢠Dishwasher Door Latch âAssembly
The âA00099902 Frigidaireâ Dishwasher Door⢠Latch serves⣠as both the mechanical closureâ and â˘the âsafety interlock that permits the control board to⣠start and maintain a washâ cycle.⤠Mechanically, the latch engages⤠the door striker and âŁholds the door against the tubâ flange⣠against internal â˘spray pressureâ and thermal expansion; simultaneously, an internal⤠actuator â˘operates an electrical interlock (microswitch) so the⣠controller reads a closed-door condition. The assembly’s geometry, mounting â˘hole pattern, â¤and â˘actuator â˘travel â¤are â¤matched â¤to Frigidaire door frames and striker positions,â so â˘correct function depends on proper alignment, intact â˘spring tensionand intact housing âseals⣠to limit water ingress and corrosion⢠of contact surfaces.
Functionallyâ and mechanically,⣠the âŁlatch âmust provide⤠repeatable engagement under load, reliable switch âactuationand durable mounting â¤under vibrational and⣠thermal cycling. Technicians typically⣠verify operation by âobserving fullâ striker⢠engagement, confirming continuity on the interlock âŁswitch during actuationand checking âfor âexcessive play â˘or plasticâ deformation of â˘the⣠latch body. Common âservice indicators include failure to start âthe cycle (open-circuit âon the interlock),⤠intermittent stopping mid-cycle, âorâ a door â¤that â¤will not stay closed. Practical replacementâ steps include confirming â˘part compatibility⣠with⢠the appliance using the part number, ensuring striker alignment before final torqueingâ of fasteners,⣠and⢠testing switch⢠continuity after installation.
- Primaryâ functions:⣠secure door under pressure and actuate control boardâ interlock
- common⣠failure⣠modes: worn⣠actuator, â˘broken housing, â¤corroded electrical contacts
- Service checks: strikerâ engagement,â switch continuity, visual inspection⢠for cracks or⣠water âdamage
- Installation notes: align⣠striker and verify actuator âtravel before âŁtightening mounting screws
| Item | Description |
|---|---|
| Function | Mechanical retention âof door and âelectrical⤠interlock â˘to the control board |
| Failure symptoms | Dishwasher won’tâ start,⣠stops mid-cycleor door won’t âlatch |
| Compatibility | OEM replacement referenced⢠by the A00099902⤠part number for â¤compatible Frigidaire models |
How â¤the A00099902 Frigidaire Dishwasher Door⣠Latch Integrates with Interlock⣠Switches, Control Circuitsand⢠Door Actuation Mechanisms
The A00099902 âFrigidaire Dishwasher Doorâ Latch serves as âboth a mechanical closure and anâ electricalâ safety input âto the appliance control âŁsystem. Mechanically, the latch secures the door against the tub during fill and âwashâ cycles; âelectrically, â˘it contains or actuates an internal interlock switch âŁ(or switches) that report a closed-door state to the control board. When theâ latch engages,the⣠interlock⢠provides a âlow-voltage⣠signal âŁthat allows⣠the âŁcontrol logic to â˘enable⣠pumps,heaters,and door-actuated âtimers;â if âthe⤠switch does â˘not close⢠or the⤠striker âis âmisaligned,the âŁcontrol board will âinhibit theâ start â˘sequence or pause cycles to prevent water loss or injury. This⣠part is a direct-replacement component in specified â˘Frigidaire modelsand compatibility⢠should be âŁverified by matching âthe model number to theâ A00099902 âŁpart number⤠to ensure⢠striker âŁgeometry âŁand⣠mounting bosses âalign⤠correctly â˘with the door and â˘bezel in a particular model series.
In typical â¤installations the latch switch is a normally-open microswitch âor âsensor wired into the dishwasher’sâ safety⣠loop; when⣠closed it â¤completes aâ circuit into a âŁsensing input on âthe main control PCB. Control firmware samples that input to sequence door-actuated operations such as locking motors â¤or timed unlockâ events âduring drain. Technicians commonly verify latch function â˘by visually checking actuator travel and performingâ a continuity test across the switch with the âdoor latched; theyâ may alsoâ measure the presence of the expected âcontrol⤠voltage when the latch is actuated. âPractical troubleshooting steps andâ common characteristics âinclude:
- Continuity test across the latch switch âwith the door closed⢠to âconfirm circuit closure.
- Inspect striker⢠alignment andâ plastic âwear that can prevent complete â¤switchâ actuation.
- Measure control-board âsensing âŁvoltage to seperate wiring/board faults from latchâ failures.
- Replace A00099902 if⣠mechanical deformation âor⣠intermittent switch operation is found.
| Item | Description |
|---|---|
| Switch type | Normally-open âmicroswitch or contact sensor integrated into latch housing |
| Typical wiring | Two-wire âsafety input to control board (low-voltage sensing loop) |
| Common symptom | Cycle won’t start, door unlocks âmid-cycleor leakage at door edge |
Common Failure⤠Symptoms and âŁDiagnostic Indicators for Door Latch Malfunction (mechanicalâ jamming, âelectrical faults,â and water⢠ingress)
The A00099902 frigidaire Dishwasher âDoor Latch âŁperforms two linked⣠functions: it provides a mechanical catch âthat⣠holds âthe door firmly closed against the âŁtub sealand it âŁhouses one or more electrical switches⢠thatâ signalâ the control boardâ that the door is latched. Mechanically,â the latch âmust engage the strike⤠and resist the âwash-cycle torque that can otherwise âpry the door open; âŁelectrically, the â˘internal⣠microâswitch or âŁsolenoid must change state â¤reliably toâ allow the machine âto start. Compatibility concerns âare mainly⣠mechanicalâ fit â˘and connector pinout – replacing a worn or broken latch with the âcorrect A00099902 unit preserves the original âactuator geometry and electrical interface,â reducing theâ need to modify âŁthe door strike or âharness.In field examples, a dishwasher that will not start but âshows⢠an intact door seal often traces to the latch assembly:⣠either the⢠actuator isâ sheared, the switch contacts haveâ burned,⤠or âforeign debris prevents full engagement.
Diagnosis combines visual⢠inspection,simple mechanical checks,and electrical testing. â˘begin with a visual/physical check âforâ bent strike â˘plates,crackedâ plastic,intrusion of detergent residue or hard⤠water deposits,and any⣠signs of corrosion⤠on connector pins; disconnect power ⤠before separating the harness. With the doorâ open, manually â¤operate the latch⢠actuator âto âverifyâ smooth âtravel â˘and audible â˘click; âthen withâ a multimeter check for switchâ state changeâ as the actuator moves â˘-⤠the switch should change continuity state reliably each cycle.If continuity switches but âthe control still â˘reports a door fault, measure the expected control voltage at the latch connector per the⣠model’s âservice manualâ and inspect wiring âfor intermittent breaks. typical repairâ actions areâ cleaning/lubricatingâ the striker area,⢠replacingâ corroded harness sectionsor â¤swapping in a known-good A00099902â assemblyâ to⣠confirm resolution.
- Door⢠fails toâ start and noâ audible latch click
- Intermittent starts⣠or stops during cycle
- Door will not stayâ closed orâ popsâ open under load
- Visible corrosion, mineral depositsor water âin the latch housing
- Control âboard registers a door/latch fault or fuse/circuit trips â˘when doorâ should lock
| Item | Description |
|---|---|
| Mechanical âbinding | debris, bent â˘strike,⤠or broken actuator prevents full â¤engagement; inspect and âmeasure â˘travelâ before replacing. |
| Electrical⣠contactâ failure | Worn or burned â˘switch contacts âshow open/unstable continuity; âverifyâ with multimeter while actuating the latch. |
| Water âingress/corrosion | Corrosion âon pins or solenoid coils âcauses intermittent faults; clean connectors âor replace âlatch assembly ifâ pitting is âŁpresent. |
Replacement Considerations and Installation Procedure for Compatible Frigidaire â¤Models
The A00099902 Frigidaire âDishwasher Door Latch performs both⣠a mechanical and electrical function: it secures the⣠door during wash cycles â¤and actuates the⣠doorâsense switch that allows â˘the control board to start and run a cycle.â The assembly⢠consists of a âplastic⣠housing, â˘a metal or plastic⣠striker⤠engagement, an internal spring/camand âanâ electrical connector forâ the âdoorâswitch.⢠Typical failure modes include⣠broken âor worn engagement hooks, brittle âŁhousing fractures, âŁjammed cams, âor intermittent electrical contacts.â Compatibility differences â¤between frigidaire â¤model groups areâ usually limited to mounting âtab spacing and connector orientation, so confirm the â˘appliance model number against parts diagrams before replacement;⤠substituting a latch with a⢠different actuator length or screw pattern can leave the⤠door misaligned or prevent the control from recognizingâ a closed door.
Follow a controlled sequence for â¤replacementâ to avoid damage to âthe inner door panel and to ensure safe operation: â disconnect power, support the door to prevent sagging, â˘remove the inner âdoor panel â¤fasteners, note âŁrouting and clip locations for the wiring âŁharness,⣠unplug theâ connectorand remove the latchâ mounting screws.⢠Install the replacement latch⤠byâ seating the housing flush⤠with the âdoor frame, âŁtorqueing âthe fasteners to snug only,⢠and verifying the striker engages smoothly across the full⣠travel of the hinge. after âreassembly, check doorâswitch continuity with a multimeter⤠and run an empty wash to confirm the control detects the closed door and that âthere are âŁnoâ leaks caused by âmisalignment. If the⣠door doesâ not close flush or the switchâ does not register, inspect â˘hinge alignment and⣠striker height before condemning the new latch.
- Verify⣠model/part â¤match, connector orientationand mounting âhole spacing before installation.
- Support the⣠door to prevent hinge strain when âremoving the inner panel.
- Check electrical continuity of the door switch â˘after installation.
- Test with âan empty cycle and observe â˘latch engagement and door â¤seal.
| Item | Description |
|---|---|
| Compatibility | Match appliance model â˘number âand confirm mounting tab spacing and⣠connector type. |
| Tools | Screwdrivers,â Torx/Phillips set, multimeter,⣠trim tool âto⣠release clips. |
| Fasteners | Typically small machine or⣠sheetâmetal screws; snug only toâ avoid⤠stripping plastic. |
| Electrical | Twoâ â˘or⢠threeâpin connector for the doorâsense switch; ensure secure seating and⢠no exposed wiring. |
| Validation | Continuity test of switch, âvisual⢠check of engagementand an empty wash cycle test. |
Q&A
What is the A00099902 Frigidaire dishwasher door latch?
The A00099902 is âŁa replacement door latch assembly used on some Frigidaire dishwashers.⣠It secures the door closed during a wash cycle andâ contains one or⣠more switches that tell theâ controlâ board the door is⤠latched and âit is safe⤠to run the machine.
What⤠are common symptoms that the door latch (A00099902) is failing?
Typical signs include âthe dishwasher not starting orâ pausing mid-cycle, the door not staying closed or feeling loose, error codes âŁrelated âto the dooror the control panel⤠acting asâ if the door is open. intermittentâ operation can indicate â¤a failing latch switch⢠or worn â˘mechanical components.
How can I⤠test whether the latch is â˘the problem?
First, visually â¤inspect the⢠latch and strike for broken partsâ or misalignment. With power⣠disconnected, âremove the inner door panel⤠to access the latch. Useâ a multimeter to check the âlatch switch(es) for continuity while actuating the latch â˘mechanism. If âŁthe switch does not âŁchange state when theâ latch is actuated,theâ latch assembly is highlyâ likely defective. If the switch checksâ out, inspect wiring and the door strike/hinges for alignment issues.
Is the A00099902 compatible with all Frigidaire dishwashers?
Not necessarily. compatibility depends on the â¤specific âmodel âand production date. âAlways verify compatibility by checking⤠your dishwasher model number and the part number inâ the âmanufacturerâ parts list or the retailer’s âcompatibility âtool before buying.â The retail listingâ or Frigidaire âparts⣠website âcan âconfirm fitment.
How difficult is it to replace theâ A00099902 latch and what toolsâ are needed?
Replacement is â˘generally a moderate DIY⤠task. Typical⣠tools are a Phillips screwdriver, â¤nutâ driver â˘or socket setand a multimeter for testing. You must disconnect power at the breaker before starting, remove the inner door panel screws, unplug the⤠latch connector, remove theâ old latchand install⤠the new one.Reassemble âŁthe door âand⣠test operation.If you’re⣠uncomfortableâ working inside the door âor with electrical⤠components,hire âa qualifiedâ technician.
What safety precautions should I take before replacing the door latch?
Disconnect electrical âpower to the dishwasher at⣠the circuit breaker (do not rely on just turning the control â¤off). Close â˘the water âsupply if you âwillâ be removing âany plumbing parts.⢠Be careful âhandlingâ theâ inner door panel and glass-support the door soâ it⤠doesn’t swing or fall. Avoidâ testing âlive⢠circuits with exposed âconnectors; if live-voltage checks are required,use⣠appropriate insulated tools and safety practicesâ or call a technician.
Can Iâ use an aftermarket latch instead âof âthe OEM A00099902?
Aftermarket latches may be â¤available and can be⢠less expensive, butâ compatibility and long-term âŁreliability can vary.if you choose an⣠aftermarket part, ensure it â¤explicitly lists your dishwasher model and matchesâ electricalâ connector types and mounting points. When⢠possible, OEM âparts from Frigidaire â¤reduce the risk â¤of fit or â˘electrical â¤differences.
What else should I check⤠if replacing the latch doesn’t fix the problem?
If⤠a âŁnew latch doesn’t âresolve the issue, check the door strike and hinges for proper alignment, the â¤wiring harness⣠and connector for damage or corrosionand the control âŁboard for faults. â¤Some â˘dishwashersâ also use a door lock motor or âinterlock â˘that’s â¤separate â¤from the latch switches-verify that component âif present.â If⤠diagnosis â˘is unclear, âconsult a qualified appliance technician or Frigidaire service to avoidâ replacing⤠multiple âparts unnecessarily.
To Conclude
The A00099902 Frigidaire âŁdishwasher âdoor latch plays a central role in safe and âeffective dishwasher â˘operation by securing the door, maintaining aâ watertight sealand engaging the appliance’s safety interlock so cycles run only when theâ door is properly closed. A functioning latch helps⤠prevent leaks, supports consistent âcleaning performance, âŁand reduces⤠theâ risk of midâcycle interruptions or energy âloss, making it â¤a smallâ but âessential component for appliance âreliability and household âsafety.
Accurate diagnosis â˘isâ important because doorârelated symptoms can⣠stem from⤠a range âŁof causes, including misalignment, worn components, electrical faultsor buildup âŁaround the latch. Simple adjustments⤠or cleaning⤠can sometimes resolve issues, but when âthe latch isâ mechanically⢠damaged or electrically faulty, timely replacement with the correct A00099902 part ensures âproper âfit andâ function. Using the specified replacement partâ and following manufacturer âinstallation guidelines reduces âŁthe likelihood of recurring problems⣠and potential safety concerns.
When replacement is⢠required, considerate practices-such as âconfirming model compatibility, performing⤠basic electrical âand âmechanical checksand âtesting the door mechanism after installation-will restore dependable âoperation and help extend applianceâ life. For those unsure of the diagnosis or uncomfortable âwith electrical or mechanical work, engaging a qualified technician⤠ensures the job âisâ completed safely and inâ accordance⤠with standards, protecting both âthe appliance and the household.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
