137311900 Frigidaire âWasherâ Pump⤠is âa motor-drivenâ drain pump assembly⤠designed for use inâ Frigidaireâ washing machines.It typically combines⣠anâ electric motor and a⢠small â˘impeller â˘within a molded housing toâ evacuate waterâ from the âŁwasher tub duringâ drainâ cyclesand is secured to the washer chassis âor tub with mechanical fasteners âand a hose connection.
Within the appliance, the pump’s primary ârole is to move âwaste âŁwater from the âŁwashâ tubâ through the drain hose to theâ household plumbing; it therefore âinterfaces âŁdirectly â¤with⢠the tub outlet, drain hoseand nearby sealsand is controlled electrically by the âŁmachine’s control board⤠or timer. âFunctionally it interactsâ with the â¤water-level sensing or pressure system (to âcoordinate drain âtiming),â the âŁlid or door⤠lock interlock (to âprevent draining during unsafe conditions),⢠and the washer’s power⢠and⤠wiring harness;â failures can be mechanical (cloggedâ impeller, âbearing wear,â leakingâ seal) or electricalâ (motorâ windings, connectorsor control-circuit faults).
this⣠article explains the pump’s⣠operating âprinciples and â˘functional â˘specifications relevant toâ diagnostics,â outlines â˘how to verify part compatibility and⣠fitment⣠for a given machine, â¤describes common failure âŁsymptoms âŁsuch as non-draining,⢠humming, noise â¤or leakageand â¤provides step-by-step troubleshooting checksâ (visual inspection, continuity and voltage testsandâ blockage removal) âas⤠well⢠as practical replacement considerations including safety precautions, requiredâ gaskets/clamps, âand âtips â˘for correct reassembly and leak âtesting.
Table of Contents
- Function âandâ Role of âŁthe âwasher âDrainâ Pump in âExtraction â¤and Drain âControl
- How the 137311900 frigidaire âŁWasher Pump Operates Within the âWasher’sâ Drainage⢠and Control⣠System
- Common Failure Modes and Diagnostic symptoms of⣠Frigidaireâ Washer⢠Pumps
- Compatibility, Replacement Considerationsand Step-by-Step âInstallation for⢠the 137311900 Frigidaire Washer Pump
- Q&A
- key takeaways
Function and Role of the⤠Washer Drainâ Pump in Extraction andâ Drain⢠Control
The 137311900 Frigidaire Washerâ Pump performs the âprimary hydromechanical task of evacuating wash âand rinse water⢠from the tub and â˘maintaining controlled â˘flow during the extraction phase. Whenâ the washer enters a drain or spin cycle the pump is driven by its âmotor assembly âŁto create sufficient flow through the drain hose⢠soâ the âŁcontrol â˘board can monitor tub conditions and âŁallow high-speedâ spin without residual water causing imbalance.â The⣠pump housing⤠guides flow past⢠theâ impeller and into the âoutlet;â integratedâ features such as a molded⢠volute,⤠trap chamberor aâ simple check valve⢠help âŁprevent backflow and reduce âthe âŁchance of residual water remaining in the tub between cycles.
Technically,the pump⣠behaves as a flow device coupled â¤to the machine control:⢠it runs untilâ the âpressure or âwater level signals that â¤the tub is empty or until a timed drain â˘interval⢠completes. Compatibility considerations for replacement âŁinclude mounting flange âgeometry, electrical connector pinoutand the pump’s hydraulic âorientation relative to theâ tub and drain hoseâ – a mismatched âorientation can reduce âflow rate or create⤠air â˘pockets that impair extraction.â Typical field symptoms âthat indicate⤠the pump needs inspection or replacement âinclude reduced⣠orâ no â¤water â¤discharge, a loud grinding⤠orâ humming noise âduring operation, visible leaks at the housing,â and⤠intermittent âoperation caused by electrical âfaults or â¤clogged debris.Practical troubleshooting often involves checking â˘the outlet âhose for obstructions,â verifying supply â˘voltage at theâ pump connectorand⢠inspecting â¤the impeller for âdamage or foreign objects.
- No âdischarge orâ slow drain
- Humming motor with no impeller⢠movement
- Leaking at housing⤠seams âor â˘seals
- Intermittent âŁoperation or thermal cutoff trips
| Item | Description |
|---|---|
| Part | 137311900â Frigidaire Washer⢠Pump âŁ- âdrain/evacuation⣠assembly |
| Primary function | Evacuate â¤tub water during drain and enable extraction cycles |
| Common faults | Impeller obstruction,â motor failure, sealâ leaks, electrical connector⤠issues |
How âthe 137311900 Frigidaire Washer Pump Operates Within the â¤Washer’s Drainage and âControl System
The 137311900 âFrigidaire âWasher⤠Pump âŁsits at the âlow point â˘of the washer tub and evacuates wash â¤and rinseâ water through the drain hose during⢠the⣠washer’s âŁdrain cycle. â¤The pump is a compact electric unit with â˘an impeller-driven⤠chamber;⤠the washer’s main⣠control board⤠energizes the pump âŁvia a relay â˘or triac to apply line powerâ for â¤the duration of the drain command. â˘In normal operation the pump must âseal to â˘the tub outlet,tolerate small debris,and âmaintain sufficient head to push water through theâ home’sâ plumbing âtrap; failures that allow âair leaks,impellerâ damage,or motorâ brush wear will reduce flow or cause complete⤠loss of drainage. Such âŁas, a pump that humsâ without moving water often indicates an âŁobstructed impeller or a⢠downstream restriction such as a kinked âhose, whereas a pump that does not energize at all suggests âa âŁcontrol or wiring fault rather than a hydraulic problem.
Technicians⤠and appliance owners should âtreat the 137311900 â˘Frigidaire Washer Pumpâ as â¤both an electrical load⤠and a hydraulic â¤component: verify â˘the control board sends the expected âŁdrive signal before replacing the pump,⣠and confirm âphysical compatibility of mounting tabs, inlet/outlet diametersand electrical connector types whenâ sourcing replacements. Common practical diagnostics include â˘listening for motor noise during a âdrain command, checking for resistance/continuity across the pump motor leadsand visually inspecting the⢠impeller housingâ for debris or cracks. Field replacement examples: â˘if the âpump⢠spins when bench powered but fails to clear standing water in the machine, inspect the drain hose and trap; if the pump receives no voltage, trace the â˘wiring âŁand test the control relay or lid/door interlocks that âcan inhibit âthe drain⤠command.
- Primary function: âevacuates tub water during drain and pump-outâ phases.
- Control interface: driven by washer control âŁboard via relay/drive circuit.
- Typical â˘failure modes: impeller clogging,⣠motor brushâ wear, cracked housingor electrical connector faults.
- Diagnostic⢠cues: humming with no âŁflow,⢠intermittent âŁoperation, leaks âŁat pump housing â˘or⤠couplings.
| Item | Description |
|---|---|
| Role | Impeller âŁpump that removes wash âŁwater and âdelivers âit âtoâ the âdrainâ hose/plumbing. |
| Drive type | Small⤠line-powered â˘electric motor controlled⢠by⢠the washer’s electronics. |
| Interfaces | mounting flange, inlet/outlet hose connections, two- or â˘three-pin electricalâ connector. |
| Maintenance checks | Inspectâ impeller for debris, test motor⢠continuity, verify control board provides drive signal. |
Common Failure Modes and Diagnostic Symptoms of Frigidaire Washer Pumps
The 137311900 Frigidaire Washer Pump is âthe drain assembly that evacuates wash â¤water from the tub; it combines a â˘smallâ electric â¤motor, âan⢠injectedâmolded pump housing,⣠an âŁimpeller and shaft âseals. Common mechanical âfailure modes include impeller blockage or entanglementâ with fabric and debris, shaft/bearing wearâ that âcauses âthe rotor to sieze or run eccentricallyand seal failure that produces external âŁleakage and shorted windings. Electrical âŁfailures present as⣠open or shorted motor windings, intermittent connector âfaultsor broken leads; because⤠mounting flanges and electrical harnessesâ can vary between⢠model series,â technicians shouldâ verify connector pinout,â mounting orientation and â¤seal type before â˘assuming interchangeability⤠with other Frigidaire pumps.
Diagnosingâ pump âfaults âfocuses onâ separating â˘mechanical from electrical causes:⢠visuallyâ inspect⢠and manually rotate the âimpeller âto detect binding or â¤foreign objects, listen for a steadyâ motor hum â˘versus an irregular knocking or grindingand âmeasure âcontinuity across the motor âand the presence of driveâ voltage⤠at the pump connector âduring theâ drain cycle. â˘Such as, if the control âsuppliesâ lineâ voltage⤠to the pump⤠but the impeller does not turn, âthe âfailure is usually mechanicalâ (blocked impeller, seized bearings or⤠broken shaft);â if⤠there is no drive voltage, investigate⤠the âcontrol board, lid/door switch⣠and wiring⤠harness. Routine practical checks include clearing the â˘trap/tub sealâ area,⢠inspecting hoses for â˘kinksâ and verifying that replacement pumps match the electrical connector⣠and mounting geometry for the specific Frigidaire âmodel.
- No â¤drainâ and no noise: likely open winding, faulty connector,â or no control output-check âcontinuityâ and⤠control voltage.
- Hums but â¤won’tâ pump: impeller jammed,seized bearings,or collapsed impeller-inspect and rotateâ impeller manually.
- Intermittent âoperation: â loose connector, intermittentâ wiring breakor failing motor brushes/electronics-wobble connectors and backprobe âduring âcycle.
- Water leaking at⣠pump: ruptured â˘housing or failed shaft seal-replace pump assembly to ârestore pressure integrity.
| Item | Description |
|---|---|
| Humming with no flow | Motorâ energized but impellerâ mechanically⣠blocked or bearings seized; clearâ debris or replace pump. |
| No âpower to pump | Control board, lid switch or â˘wiringâ fault preventingâ drive voltage;⣠verifyâ commands at connector⣠before replacing pump. |
| External leakage | Worn shaft seal or⣠cracked â¤housing; replacement pump assembly and âhose clamps ârequired. |
Compatibility, Replacement Considerations,â and⣠Step-by-Stepâ Installation for the 137311900 Frigidaire Washer Pump
The âŁ137311900⤠Frigidaire Washer Pump âis a compact âcentrifugal drain⤠assembly that evacuates wash and rinse waterâ through a molded housing âŁand impeller âdriven⣠by a small AC motor.Typical operational behavior includes a brief high-torque start â¤as theâ impellerâ breaks free⢠of debris, â¤followed⢠by steady-state flow; common âfailure modes are â˘impeller damage, seizedâ bearings, motor windings shorting, âcracked housings, âor clogged inlet screens. Compatibility depends on mechanical mounting â˘points, electrical âconnector typeand inlet/outletâ orientation â- â˘verify the pump’s mounting flange pattern, âtab â¤spacingand whether the harness is a 2â or 3âpin connector âagainst the washer’s service manual or theâ original pump.Technicians should âalso confirm⣠nominal supply⤠voltage âŁand duty cycle; for example, many domestic models use 120 VAC withâ short âintermittent âŁduty âfor drain cyclesand⤠a failing pump often presents⤠asâ humming withoutâ water movement⣠or âŁintermittent âdraining âdue to⢠partial blockage or worn impeller blades.
- Power⣠off and isolate:â disconnect âmains andâ shut off water supply; drain residualâ water into âa bucket before opening panels.
- Access pump: remove the⣠access panelâ or â¤front⤠panel toâ reach theâ pump housing; document hose routing and connector orientation with â˘a⣠photo.
- Disconnect âhoses and harness: loosen clamps,â capture residual waterandâ unplug the electrical connector; check for corroded⣠terminals.
- unfasten mounting⤠screws⤠and⤠remove the pump assembly;⢠inspect the sump forâ debris, foreign â˘objectsor a clogged trap.
- Install the â¤replacement, align tabs and gaskets,â secure fasteners to original torque, âreconnect⢠hosesâ and harness, âand restore water and power.
- Run a diagnostic or a drain cycle to verify flow, check for⤠leaksâ at clamps and sealsand⣠listen for abnormal vibration âor noise âŁindicating misalignment or loose mounting.
| Item | Description |
|---|---|
| Voltage | Typical 120 VAC (verify âon â¤model label) |
| Connector | 2- or 3-pin inline harness – confirm⣠pinout before swapping |
| Flow / Duty | Short intermittent drain cycles; âverify motorâ runs under load |
| Symptoms | Humming âwith no âdrain,slow â˘draining,leaks at pump housing |
Q&A
What is the 137311900 âFrigidaireâ washer pump and which⢠washers use it?
The âŁ137311900 is â˘a âreplacement âdrain âpump assembly designed for many Frigidaire âŁ(and some Kenmore/White-Westinghouse⤠rebranded) washing⢠machine models. It replaces the motorâ and impeller assembly that pumps âwater out during âtheâ drain cycle.Always verify⤠compatibility âby matching âŁthe part number â˘to yourâ washer model number or by comparing the physical pump âto⣠the old⣠unit – âŁmodel-to-part lookup âon the manufacturer or parts reseller⢠site will confirm fit.
What are the common⤠symptoms thatâ indicate the⤠137311900 pump has failed?
Common signs of aâ failing or failedâ drain âpump include: âwasher not â˘draining or drainingâ very slowly, âŁwater remaining âin the drum â¤after the cycle, a humming noiseâ without âwater movement (motor stalled), loud âgrinding or rattling â˘noises (bearing or debris issue)or error codes related to drainage on machines⣠with â˘electronic controls.Before replacing the pump, â¤check hoses and the â¤drain trap âŁfor clogs âŁand verify the machine âis actually commanding â˘the pump to run.
How can a technicianâ test the 137311900 âpump toâ determine if âit â¤is indeed âbad?
Begin â¤withâ safety: unplug the washer and shutâ off water. Inspect visually for obstructions in the impeller area and the drain hoses. With⢠power⤠disconnected, use a⣠multimeter⢠to check â¤the âpump motor for electrical continuity (it⤠should show âa⣠low resistanceâ reading -â not âan open âŁcircuit).To test operation, restore power temporarily and run a â¤drain cycle⢠while measuring whether the pump âreceives mains voltage during⤠the drainâ step. If⤠the pump gets correct voltageâ but does not turn, theâ pumpâ motor⤠is defective andâ should be replaced.
Whatâ tools and âskills are required to âŁreplace the 137311900 â˘pump?
Replacing this⣠pump typically requires basic appliance ârepair skills and common⤠tools: screwdriver âŁ(Phillips and flat), nut driver âor small socket⢠set,â pliers,⤠a bucket for water,â andâ optionallyâ aâ multimeter.You should â˘be comfortable âdisconnecting⢠power, draining residualâ water, removing access â˘panels, loosening hose clamps,â andâ reinstalling⤠electrical connections. if you areâ not comfortable âŁworking with mains⣠electricity or âdisassembling the washer, hire a qualified applianceâ technician.
How do âI remove debris or âunblock the pump without replacing the 137311900?
First unplug the washer âŁand place⤠towels/bucket to⣠catch⤠water.â Access the pumpâ or âŁdrain⣠filter per your washer’s service⤠instructions (front panel or bottom access). Removeâ andâ inspect the pump inletâ and impeller area for foreign objects (coins, â¤hairpins, lint).⣠Remove any debris, check the âdrain hose⤠for kinksâ or clogs,⢠and⤠reassemble. If⤠the âimpeller turns freely by hand and the motor⢠has continuity, the pump⢠may â˘not need replacement. Always test with a short âŁdrain â˘cycle after reassembly.
Is the 137311900 pump â¤noisyand what ânoises indicate a âproblem?
Some ânormal operational noise is expected⣠as the⢠pump runs,⤠but â˘unusual loud noises â¤indicate⢠problems: grinding/scraping usually means a damaged âimpeller or bearingsâ or âa foreign object is contacting the impeller; loud hum with no rotation suggests the motor is stalled; high-pitched squeal can indicate worn bearings. â˘If⤠cleaning⣠the pump and removing⤠foreign objectsâ does not eliminate abnormal noise, replacement âof⢠the pump assemblyâ is ârecommended.
How long does the 137311900 pump typicallyâ last and is there a warranty?
Life expectancy âvaries with usage and water conditions but aâ washer drain âpump commonly lasts several years⤠(often 5-10 years).⣠Heavy use, small-parts âingestion (coins, â¤debris)or electrical faults shortenâ life. Warranty coverage depends â¤on âŁwhere âyou purchase theâ partâ – retailers and â˘manufacturer⣠parts departments frequently enoughâ provide âa limited âwarranty (periods vary). Check the seller’s warranty⣠policy and â¤keep your purchase receiptâ for claims.
can I âreplace theâ 137311900 pump myself,and what safety⤠precautions should âŁI â˘take?
Yes,manyâ owners âcan replace the âŁpump themselvesâ if⤠they areâ comfortable⢠with basic repairs. Safety precautions: unplugâ the⣠washer and turn offâ water supply; have towels/buckets ready for residual water; âtake photos of⤠wire connections beforeâ disconnecting for⢠correct reassembly; avoid working with live electricity⢠unless â¤youâ know âhow to safely test forâ voltage andâ run a diagnosticâ cycle. If unsure at any point, âstop and call a qualified appliance technician.
key⣠Takeaways
The â¤137311900 Frigidaire washer pump serves as aâ critical âcomponentâ inâ the laundry âappliance’s â¤water âmanagement system, âŁresponsible for moving⤠and evacuating water during wash and drain cycles. âIts reliable operation helps ensure âproper cycle completion,â prevents standing⣠water â˘and associated âodorsand âŁcontributes⤠to the overall cleaning⢠performance⣠and⢠longevity of the washer.
Accurate diagnosis and timely replacement â¤of a failing â¤137311900 pump are criticallyâ important to â¤restore full âfunctionality and prevent secondaryâ damage toâ the washer. Identifying pump-related symptoms-unusualâ noises,incomplete draining,orâ error codes-followed âby⤠verification of the correct part number and âproper âinstallationâ will minimize downtime and reduce the risk of further faults. When⣠in⣠doubt, consulting the appliance manual or a âŁqualified serviceâ technician helps âensure a safe and âeffective⣠repair.
In sum, the 137311900â Frigidaire⢠washer pump â¤plays a central role in reliable washerâ performanceand attentive diagnosis combined with⤠appropriate replacement⤠practices âpreserves â˘appliance efficiency and user convenience. Taking⢠care to use the correct part and⢠follow safe installation procedures supports âlong-term, trouble-free operation.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
