241816602 Frigidaire Refrigerator Motor-AUGER is an auger motor assembly designed to drive the helical auger inside a refrigerator ice storage/bin assembly. as a compact electromechanical drive, the part couples a small electric motor (typically fitted with a reduction gearbox and mounting hardware) to the auger shaft so that the screw-like auger can rotate and convey ice from the bin to the dispenser or ice chute.
Inside the appliance, the auger motor interfaces directly with the ice storage mechanism and indirectly with the dispenser control system. When the dispenser or door actuator signals a dispense operation, the control board supplies power to the auger motor through the dispenser switch or relay; the motor’s gearbox transmits torque to the auger to move measured volumes of ice. The assembly thus interacts with the ice maker/ice bin, the dispenser door/actuator, the main control board and related wiring or sensors; it also must tolerate intermittent stalls, low temperatures and occasional ice contact without seizing. Proper alignment, secure mounting and correct electrical connection are critical for smooth operation and to prevent jams, excessive wear or motor overload conditions.
This article will provide a technical overview of the 241816602 auger motor’s function and typical installation locations, outline compatibility considerations and how to verify fitment, describe common failure symptoms (for example no-dispense, grinding noise, intermittent operation or electrical fault)and present systematic troubleshooting steps a technician can use (visual inspection, mechanical free-spin check, connector and voltage testsand gearbox assessment). It will also cover replacement considerations such as correct orientation,retaining fasteners and seals,precautionary steps (power isolation and ice removal) and tips for confirming the new unit is properly driven and electrically connected to the refrigerator’s dispenser control circuitry.
Table of Contents
- Function and Role of the Ice Auger Motor in Frigidaire Refrigeration Systems
- how the 241816602 Frigidaire Refrigerator Motor-AUGER Interfaces with the Ice Dispenser: Mechanical Drive, Electrical Controland Sensor Integration
- Common Electrical and Mechanical Failure Symptoms of the Auger Motor and In-Situ Diagnostic Indicators
- Compatibility, Replacement Considerationsand Installation Procedures for the 241816602 Frigidaire Refrigerator Motor-AUGER
- Q&A
- Wrapping Up
Function and role of the Ice Auger Motor in Frigidaire Refrigeration Systems
The 241816602 Frigidaire Refrigerator Motor-AUGER is the electromechanical drive that turns the auger paddle inside the ice bin to transport ice from the storage area to the dispenser chute. In operation the motor provides low-speed, high-torque rotation through a gear-reduction assembly and a splined or keyed shaft interface; the control board or dispenser switch energizes the motor for short intervals to dispense measured volumes of ice. Technically, the component must withstand repeated start/stop cycles, occasional reverse torque from jammingand thermal stress inside the freezer cabinet, so its mechanical coupling, mounting flangeand electrical connector are designed to match specific frigidaire assemblies for reliable fit and alignment.
Functionally, technicians should view this motor as both a drive device and a system sensor: changes in acoustic signature (humming, grinding) or increased stall frequency are diagnostic indicators of internal gear wear, bearing failureor foreign-object interference in the auger path. confirm compatibility by matching the refrigerator model number, connector pinoutand mounting pattern before replacement; during diagnosis use a multimeter to check coil continuity, inspect the harness for corrosion, and verify the control board provides the expected actuation signal. Practical bench tests include manually rotating the shaft to verify free movement and observing motor behavior under controlled power with proper safety precautions-replace the motor if windings show open/short conditions, gears are strippedor the unit seizes under normal load.
- Primary role: rotate auger paddle to move ice from bin to dispenser
- Key behaviors: low-speed high-torque output,intermittent duty,tolerance for freeze/thaw cycles
- Common symptoms of failure: no rotation,excessive noise,intermittent operation,burning odor
- Technician checks: connector pinout,continuity,free shaft rotation,control-board actuation signal
| Item | Description |
|---|---|
| Function | Delivers torque to the auger paddle to reliably feed ice to the dispenser |
| Failure modes | Seized geartrain,worn bearings,electrical open/short,connector corrosion |
| Verification | Multimeter continuity,manual shaft rotation,harness inspection,controlled bench actuation |
How the 241816602 Frigidaire Refrigerator Motor-AUGER Interfaces with the Ice Dispenser: Mechanical Drive,Electrical Control,and sensor Integration
The 241816602 Frigidaire Refrigerator Motor-AUGER provides the mechanical and electrical interface that turns stored ice into dispensed portions. Mechanically, the motor couples to the auger shaft via an OEM-specific keyed or splined connection and applies low-speed, high-torque rotation to move ice from the bin into the dispenser chute; the gear reduction and mounting orientation determine torque margin and resistance to ice bridging. Electrically,the motor is driven by the refrigerator control board through a harness and connector that carries the drive voltage and enable/start signals; the board sequences short run pulses during a dispense cycle and can reverse or time-limit the motor to clear jams depending on model firmware. Practical compatibility requires matching the shaft profile, mounting pointsand connector pinout-installing a 241816602 part into a mismatched assembly can result in improper engagement or thermal overload under load.
- Mechanical interface: splined/keyed shaft, mounting flange, torque and RPM characteristics
- Electrical interface: harness connector, drive/enable signaland ground return
- Control behavior: timed pulses, stall detection via current sensingand occasional reverse or retry logic
- Sensors and protections: door/actuator switches, ice-level sensorsand motor thermal limiters
Sensors and control logic determine when and how the motor runs: a dispenser request (lever or electronic command) plus a clear chute signal allows the control board to apply drive voltage while monitoring current and time for stalls. If the auger binds on compacted ice, the control board detects elevated current or lack of expected rotation and may cut power or attempt short reverse cycles; technicians typically diagnose faults by checking voltage at the motor connector during a dispense command, verifying continuity of the motor windingsand inspecting the auger for mechanical obstruction.For example, replacing the motor with a correctly matched 241816602 part and confirming the connector pinout and harness continuity frequently enough resolves intermittent non-rotation problems, whereas consistent high-current draws point to ice bridging or a worn geartrain rather than an electrical control fault.
| Item | description |
|---|---|
| Shaft profile | OEM-specific keyed or splined interface; must match auger |
| Connector pins | Drive/enable and ground; verify pinout before replacement |
Common Electrical and Mechanical Failure Symptoms of the Auger motor and In-Situ Diagnostic Indicators
The 241816602 Frigidaire Refrigerator motor-AUGER rotates the auger assembly that moves ice from the ice maker bin to the dispenser or ice chute. In normal operation the motor receives a control signal from the dispenser/control board and must deliver continuous torque at low speed; mechanical drive components (gears,splines,clutch) and electrical windings must remain within specification to avoid stalling or grinding. For compatibility, replacement with the same part number preserves the original pinout, gear orientationand mounting dimensions; when substituting a different motor, verify harness connector, gear ratioand physical fit to prevent misalignment or increased load on the drive train.
- No motor response when dispenser is actuated (no rotation or click) – indicates open circuit, missing drive voltageor failed motor windings.
- Intermittent rotation or slow spin under load – can be caused by worn brushes/commutator, partial winding shortor marginal drive voltage from the control board.
- Loud grinding, clicking, or scraping – usually mechanical: damaged gears, stripped splinesor ice jamming the auger path.
- Motor runs but ice does not dispense or stalls under load - points to slipping/clutch failure or excessive friction from ice blockages.
- High current draw, blown fusesor thermal shutdown – electrical fault in the motor windings or motor stalling against a jammed auger.
Practical in-situ diagnostics begin with verifying the control command at the motor harness while actuating the dispenser: confirm the presence and type of drive voltage (pulse or steady) per the service manual, then check motor continuity and resistance with a multimeter for open or shorted windings. If voltage is present but the motor does not turn, isolate the mechanical load by freeing the auger and retrying; rotation with no load but stalling when loaded indicates mechanical wear or clutch slipping.Visual inspection of connectors for corrosion, melted insulation, or bent pins is often revealing; a burnt odor or discolored insulation suggests an internal short. For final disposition, compare measured electrical and mechanical indicators to service limits and replace with the matching 241816602 Frigidaire Refrigerator Motor-AUGER if the motor fails electrical or mechanical acceptance tests.
| Item | Description |
|---|---|
| Quick check | Verify drive voltage at harness during dispenser actuation; if absent, trace upstream to switch/control board. |
Compatibility, Replacement Considerations, and Installation Procedures for the 241816602 Frigidaire Refrigerator Motor-AUGER
241816602 Frigidaire Refrigerator Motor-AUGER is the drive assembly responsible for rotating the ice-auger shaft inside the ice bin and for proper dispensing of ice. Compatibility depends on three physical and electrical interfaces: the shaft and spline geometry that mate with the auger, the mounting-ear spacing and fastener pattern that secure the motor to the linerand the wire-harness/connector and control-signal format supplied by the refrigerator’s dispenser board. Technicians should confirm these dimensions and connector types against the appliance’s service diagram before ordering a replacement; a motor that matches the electrical connector but has an incorrect shaft diameter or spline profile will turn freely yet fail to engage the auger, producing the symptom of motor running with no ice movement.
Replacement procedure emphasizes verification, safe isolation of power, and correct transfer/alignment of the auger assembly. Before installation, record the motor orientation and any shims or spacers; bench-testing the motor with the correct supply and observing rotation direction can distinguish motor failure from control-board or switch faults. During reassembly ensure the spline seats fully, the mounting surfaces are flat and undamagedand the harness is routed to avoid pinch points; after reconnecting power, cycle the dispenser and observe starting torque and consistent rotation to confirm correct installation.
- Confirm part fit: compare shaft spline, flange patternand connector type to the original.
- Electrical check: isolate power, inspect harness for corrosionand bench-test motor if uncertain.
- Mechanical check: transfer auger and any spacers, verify full engagement and free rotation before final fastening.
| Item | Description |
|---|---|
| Primary function | Rotate ice auger to feed ice to the dispenser |
| Key checks | Mounting pattern, shaft/spline profile, connector pinout, rotation direction |
| Installation note | Record orientation, route harness to prevent chafing, verify engagement under light load |
Q&A
What is the 241816602 Frigidaire Refrigerator Motor-AUGER and what does it do?
The 241816602 is an OEM auger motor assembly used in Frigidaire/Electrolux style refrigerators with an ice-dispensing door. It drives the auger (spiral) inside the ice bin so ice cubes or crushed ice are moved from the bin into the dispenser chute when you press the dispenser lever or button.
How can I tell if the auger motor is failing?
Common symptoms of a failing auger motor include: the motor humming but not turning,no ice dispensing when the dispenser is activated,intermittent operation,grinding or scraping noises,or the motor stopping after a short run. Before replacing the motor, check for simple causes such as jammed ice, a stuck auger bladeor a tripped over‑current/jam protection circuit.
Can I test the auger motor myself, and how?
Yes. Basic tests: (1) Safety first - unplug the refrigerator or cut power. (2) Visually inspect for jams and remove them. (3) With power off, use a multimeter on ohms/continuity to check that the motor windings are not open (there should be continuity between motor leads). (4) With the refrigerator plugged in and the dispenser activated (use caution),measure the voltage at the motor connector - it should show the expected drive voltage supplied by the control board (refer to the service manual for the exact spec). If there is correct drive voltage when activated and the motor does not turn, the motor is faulty. If there is no drive voltage, the problem is highly likely the control board, dispenser switch, or wiring.
What tools and safety steps are needed to replace the auger motor?
Tools: screwdriver or nut driver set, possibly a socket set, needle-nose pliers, and a multimeter for testing.Safety: unplug the refrigerator or switch off the circuit breaker before starting, drain or clear the ice binand wear gloves for protection from sharp plastic edges and ice. Keep track of screws and note the orientation of the auger and motor before removal so you can reinstall correctly.
What are the basic steps to replace the motor-auger assembly?
Typical replacement steps: (1) Unplug the fridge. (2) Remove the ice bucket and any trim/panels to access the auger motor (some models require removing the freezer door inner panel).(3) Disconnect the motor wiring connector.(4) Remove mounting screws and the motor from the auger housing. (5) Transfer the auger blade to the new motor if required and install the new motor in the same orientation. (6) Reattach wiring, reassemble panels, restore powerand test the dispenser. Follow the service manual for your model; variations exist between models.
Is the 241816602 auger motor compatible with my Frigidaire model?
Compatibility depends on the refrigerator model. 241816602 is an OEM Frigidaire part used in specific models with door ice dispensers. Always verify compatibility by checking your refrigerator’s model number and cross-referencing with the part number on the manufacturer’s parts list or a trusted parts distributor. Do not rely solely on visual similarity; connector type, mounting holesand shaft orientation must match.
Why does the motor sometimes hum but not turnand how do I fix it?
Humming without rotation can be caused by: a mechanical jam (ice or broken auger blade), a stripped gearbox, a seized bearingor an internal electrical fault in the motor. First remove any ice and try rotating the auger by hand (power off). If it is free but still hums when powered, the internal gear/motor is likely bad and the motor assembly should be replaced.
Will a new auger motor require any calibration or reset after installation?
Most replacements do not require a special calibration-once installed and powered, the dispenser should operate normally. However, some newer models may perform self-checks or require a diagnostics cycle after component replacement. If the dispenser does not work after installation, check wiring and run any model‑specific diagnostic routines as described in the service manual or user guide.
Wrapping Up
The 241816602 Frigidaire Refrigerator Motor-AUGER serves as the primary drive component for the ice auger mechanism, converting electrical input into the rotational motion needed to move ice through the dispenser and out of the ice bin. its reliable operation is essential for consistent ice delivery, minimizing jams, and preserving the overall user experience of refrigerators equipped with an ice dispenser.
Because symptoms such as inconsistent dispensing, unusual noisesor a non‑rotating auger can result from electrical, mechanical, or control‑system issues, accurate diagnosis is vital before replacing the motor. When replacement is necessary, selecting the correct OEM part and following manufacturer‑recommended service practices or using an authorized technician helps ensure proper fit, safe installationand long‑term performance. Proper diagnosis and replacement protect appliance functionality and help avoid unnecessary service costs or repeat failures.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
