5303918568 Frigidaire Defrost Thermostat is a temperatureāactivated switching device used toā control the defrost cycle in ā¤frostāfree refrigeration equipment. It is indeed aā lowātemperature thermostat (typically a bimetalā orā similar temperatureāsensing switch) designed āto change state at a specified evaporator coil temperature so that the defrostā heater is enabled ā¢orā¢ disabled as required. āUnlike oneātime thermal fuses, this ā£thermostat isā intended for repeated cycling and is rated for ā£appliance line voltages and currents within the refrigerator’s defrost circuit.
Within the appliance the defrost thermostat is mounted on ā¤or near the evaporator coil and interfaces directly with the defrost heater circuit and the defrost control (timer or electronic control board).ā When theā¤ evaporator temperature falls below its cutāin point the thermostat closes to allow theā¢ heater to energize;ā as the ā¢coil āwarms to the cutāout temperature the thermostat opens to terminate the heater. In practice it also acts as a ā¢safety device to prevent overheating of the coil and heaters and to ensure theā evaporator returns to a frostāfree state without excessive runā£ time. It therefore interacts with the heater, evaporator fan, compressor cycling logic and the control board/timerā that sequences automatic defrost events.
This article will explain the thermostat’s operating principle and expected temperature ratings, describe model compatibility and crossāreference considerationsand list common failure symptoms such as persistent frosting, failed or intermittentā£ defrostā¢ cyclesand evidence of burned contacts. ā£It will provide practical troubleshooting steps forā£ techniciansā¢ and owners – including visual inspection, continuity checks at cold and ambient temperaturesand system isolation ā¢tests – andā¤ cover replacement considerations like matching temperature setāpoints, connector types, mounting method, safety precautions,ā£ and verification procedures after installation.
Table ofā£ Contents
- Function and Role of the Defrost Thermostat inā¢ Automatic Refrigerator Defrost Systems
- How the 5303918568 Frigidaire Defrost Thermostat Works Inside the Appliance and Interfaces with the Defrost Controller
- Common Electrical and Thermal failure Symptoms Indicating a Defrost Thermostat Fault
- Compatibility, model CrossāReference and Replacement Considerations for the Defrost Thermostat
- Q&A
- Insights āand Conclusions
Function āand Role ā¤of the Defrost Thermostat in Automatic refrigerator Defrost āSystems
The 5303918568 Frigidaire Defrost Thermostat is a temperatureāactivated safetyā¤ device mounted to the evaporator that controls whether the defrost heater can receive power during a ādefrost cycle. mechanically it isā a temperatureāsensitive switch ā¢(often āa bimetal element)ā£ wired in series with the heater and the defrost timer or control board; when āthe evaporator temperature is below theā¢ thermostatS trip point the contacts are closed to allow heaterā current,ā and when the evaporator warms to the trip point the contacts open to remove power and prevent excessive heating. āIn practice this means the thermostat determines the end of the defrost interval based on actual evaporator temperatureā£ rather than ā¢only elapsedā time, protecting plastic trays andā refrigerant lines from overheating and limiting water āflow onto cabinet components once frost has melted.
Technically, compatibility depends on matching the thermostat’s trip temperature, physical ā¢mounting clip, terminal typeand ā£wire color/length-substituting a thermostat withā differentā¤ trip characteristics ā¤can lead to ā¤incomplete defrost or heater overrun. For field ā¢diagnosis and replacement, ā¤common procedures are: measure continuity with the sensor cold (should read closed/low resistance), then warm the sensor with a heat gun or warm water to confirm the contacts open near the expected temperature; if theā device failsā£ these checks it shouldā¢ be replaced. Typical indicators ofā a failing unitā includeā¢ persistent frost buildāup across the evaporator (thermostat stuck open) or evidence of prolonged heater operation and āmelting after the cycle ends (stuck closed).
- Symptoms to watch: uneven frost, icicle formation,ā water pooling under the freezeror heater running continuouslyā¢ during defrost.
- Basic test: cold continuity check, then warm to verify opening; ensure power is removed before performing electricalā¤ tests.
- Replacement note:ā¢ match trip range and mounting style rather than āonly terminal color.
| Item | Description |
|---|---|
| Type | Temperatureāactivated mechanical defrost thermostat (bimetal style) |
| Contact behavior | Normally closed at low evaporator temperatures; opens at the thermostat’s trip temperature |
| Typical trip range (approx.) | Opens as the ā£evaporator āwarms through the low tens to midātens Ā°C range (match exact spec for replacement) |
| Function | Permits defrost heater current only while evaporator āis below trip ā¢temperature; ends defrost byā opening āthe circuit |
Howā¢ the 5303918568 Frigidaire defrost ā£Thermostat Works Inside the Appliance and ā¢Interfaces with the Defrost ā¤Controller
The 5303918568 Frigidaire Defrost Thermostat ā¢ is a temperature-actuated switch that directly monitors the evaporator ā¤coil temperature and interrupts the defrost heater circuit when the coil reaches its cutoff temperature. Physically ā£mounted on ā¤or clipped to the evaporator, the thermostat is wired in series with the defrost heater so that when theā defrost controller energizes the ā£heater the thermostat either allows current to āflow (closed) while the coil is cold or opens when the coil warms to the thermostat’s setpoint, preventing excessive heating of the coil and surrounding components.
In a ā£refrigerator’s defrost sequence the control board provides time- or event-based command to the heater but depends on the thermostat as a thermal safety limit: aā properlyā functioning thermostat terminatesā heater power as soon as the coil reaches its temperature threshold, while aā¤ failed-open thermostat prevents defrost āheating and a failed-closed thermostat removes ā¤the thermal limit and leaves cycle termination to the controller’s maximum runtime. Technicians commonly diagnose the 5303918568 by ā¢checking continuity atā low temperature (closed when cold) and verifying it opens as it warms; when replacing the partā£ match the mounting clipā¢ style, terminal typeand the thermostat’s ratedā¤ opening ā¤temperature to ensure ācompatibility and safe operation.
- Typical behavior: normally ā¢closed at cold, opens at the specified cutoff temperature.
- Wiring: installed inā series with defrost heater; interfaces directly with the defrost controller or main board.
- Common failure symptoms: frost buildup (open),heater runs ātoo long or tripped fuses (closed).
- Service note: continuity test at subāambient temperatures and visual verificationā¤ of mounting are ā¤standard checks.
| Item | Description |
|---|---|
| Function | Interruptsā defrost heater power when evaporator coil reaches cutoff temperature |
| Type | Mechanical temperature switch (normally closed at cold) |
| Typical opening temperature | Approx.4-10 Ā°Cā (40-50 Ā°F) depending on specification |
| Mounting | Clip or strap to evaporator coil; direct thermal contact required |
| Electrical interface | Two spadeā¢ terminals; āinstalled in series with heater circuit |
Common Electrical and Thermal Failure Symptoms Indicatingā aā¢ defrost ā¤Thermostat fault
The 5303918568 āFrigidaire ā¤Defrost Thermostat is a temperature-actuated switch located in the ā¤refrigerator defrost circuit that monitors evaporator temperature and permits current to the defrost heater during scheduled defrost events. In normal operation the thermostat presents a low-resistance path (closed contacts) when the evaporator is cold so the control or timer can energize the āheaterand ā¢then opens as the coil warms to interrupt heater current; common failure modes include contact ācorrosion, welded contacts,ā or loss ā¤of thermostatic responsiveness that either prevent the heater from being powered or allow it to run continuously. Because this part interfaces as a simple open/closed input, compatibility is steadfast by matching terminal configuration andā the thermostat’s temperature setpoint range with the specific Frigidaire controlā system used on the unit.
Electrical and ā£thermal failures of theā¤ defrost ā¤thermostat produce distinct, measurable symptoms that help isolate the ā¤component versus other parts of the defrost system. Typical observations include persistent frost accumulation on the evaporator or freezer surfaces (heater neverā energized), an evaporator that remains warm or cycling with unusual frequency (heater stuck āclosed), blown defrost fuses or tripped breakers from intermittent shortsand inconsistent continuity behavior when theā thermostat is exposed to ācold andā¤ warm conditions; measuring continuity at ambient and at refrigerated temperatures is an effective practical check to confirm thermostat behavior.
- Heavy ā¤frost/ice on evaporator after normal run cycles – suggests thermostat not closing (open circuit when cold).
- Defrost āheater never energizes āduring service cycle – continuity āabsent when thermostat should be closed.
- Heater remains powered outside defrost cycles – thermostat contacts may be stuckā closed.
- Intermittentā£ defrost operation, blown fuse, ā¤or tripped breaker – āpossible intermittent short or degraded contact.
- Erratic temperature swings āor compressor short-cycling during ā¢defrost intervals -ā degraded thermal response of ā¢the thermostat.
| Item | Description |
|---|---|
| Normal behavior | Closed ā(low resistance)ā at cold evaporator temperatures to allow heater energization; open as coil warms ā£to terminate defrost. |
| Fault indication | Noā continuity when cold (heater won’t run) or āpermanent continuity when warm (heater may run continuously);ā intermittent continuity indicates contact degradation. |
| Practical diagnostic check | Measure continuity at ambient and after cooling the thermostat;ā¢ expected pattern is closed at cold and open at warm. Lackā of expected change āindicates replacement. |
Compatibility, Model CrossāReference and Replacement Considerations for the Defrost Thermostat
The 5303918568 Frigidaire Defrost āThermostat āis a temperatureāactuated switch mounted at the evaporator that permits the defrost heater to energize only while the coil ā¢is below āa designated temperatureandā¢ it opens whenā¤ the sensed temperature rises to indicate frost has melted. Technically, these devices are simple thermal āswitches (bimetal ā¤or capillary/bulb styles) that change state based on the evaporator temperature;ā¤ their correct āoperation prevents needless heater run time and reduces the risk of overheating the coil. When assessing compatibility, focusā¢ on the thermostat’s activation rangeā¤ and behavior, electrical rating, ā£terminal typeand how the sensor isā¤ mounted orā positioned relative to the evaporator surface rather than on cosmetic similarity or housing shape alone.
For crossāreference and replacement, compare ā£the oldā part’s stamped specifications against the candidate unit: activation temperature or range,ā¤ continuous current and voltage āratings, terminalā¤ style (quickāconnect spade, lead wires,ā etc.),ā and physical sensor length or clip arrangement. Technicians commonly verify continuity at low temperatures using a freezer or ice bath and confirmā open state at room temperature before installation as aā¢ practical test. if the electrical and thermal specifications match, aftermarket or option OEMā numbers can be acceptable; if any parameter ā¤differs-especially the activation point or current capacity-replace only with a part that matches the original specifications āto avoid ācontrol faults or unsafe operation.
- Key checks: activation temperature/range, voltage/current rating, terminal type, sensor length/mountingand physical condition (corrosion/damage).
| Item | Description |
|---|---|
| Part | 5303918568 Frigidaire Defrost Thermostat ā¢- OEM identifier to match against service literature or the part label. |
| Function | Closes at low evaporatorā temperature to allow heater operation; opens when temperature rises to terminate defrost. |
| Activation behavior | Specified temperature or range; must match appliance control ā£timing to ensure full frost removal without overheating. |
| electrical rating | Rated for theā¤ appliance supply and heater load-verify voltage and continuous/intermittent current capacity on the part label. |
| Mounting/terminals | Physical sensor length, ā¤clip typeand terminal styleā¢ mustā match for secure mounting and reliableā¤ electrical connection. |
Q&A
What is the 5303918568 Frigidaire defrost thermostat?
The 5303918568 is an OEM defrost thermostat (bimetal thermostat)ā¤ used on many Frigidaire refrigerators and freezers.It senses the temperature at the evaporator and is wired in series with ā£the defrost ā¢heaterā¤ so it can interrupt heater current if the evaporator gets too warm, protecting the heater and surrounding components during a defrost cycle.
How does this defrost ā¤thermostat work?
It is indeed a temperature-sensitive switch ā£(usually normally closed at ālow temperatures). during a defrost cycle the control or timer applies power to theā¤ heater through the thermostat. If ā¤theā¢ evaporator temperature rises above the thermostat’s trip point, the āthermostat opensā¢ and cuts power to the heater. When the evaporator cools again the āthermostat ācloses.
What are the ā¤common symptoms that this thermostat has failed?
Symptoms include ā£no defrostingā (excessive frost/ice build-up on the evaporator or in the freezer), continuousā heaterā£ operation (rare)or irregular defrost cycles. You may also observe ā¤long refrigeration cycles, poor coolingor errorā codes on electronic control boards that monitor defrost components.
How do I test the 5303918568 defrost thermostat?
Always ā¤disconnect power first.ā Remove the thermostat fromā theā evaporator area and use a multimeter set to continuity or low ohms. At room temperature it may be open; to test operation, chillā¢ the thermostat (put āin a sealed bagā¤ in a freezer or apply ice) so it is cold – a working thermostat should show continuity (near 0 ohms) āwhen cold. Warm it gently (hairā£ dryer) and it should openā (no continuity) when it passes its trip temperature. Do not test live with power applied.
What resistance or continuity ā¤values should I expect?
When closed (cold) the device should show ā¤very low resistance – typically ā¢underā£ a few ohms or show continuity on a āmultimeter.When āopen (warmed past its trip point) it should show infinite resistance (no continuity). There āisn’tā¤ aā meaningful fixed resistance āvalue like a resistor; the crucial check is closed vs. open at the appropriate temperatures.
Where is the thermostat located and howā do I replace it?
It’s usually clipped to the evaporator coil or mounted adjacent to the defrost heater in the freezer compartment. To replace: disconnectā¢ power, remove interior panels to access the evaporator, unclip ā£or unfasten the old thermostat, disconnect the two wire leads, connect the new one to the same wires (polarity is not usually relevant), secure it to the coil in the same position, reassemble panelsand restore power. Follow the refrigerator’s service manual ā¤for details and mounting orientation.
Can Iā bypass theā defrost thermostat to ā¢get the heater to run?
No. Do not bypass the defrost thermostat.It is a ā¢safety device that prevents the defrost heater āfrom overheating and creating a fire or melting components. Bypassing it can damage the appliance and ācreate a hazard. Replace a faulty āthermostat with the correct OEM or approved replacement instead.
Is 5303918568 compatible with my refrigerator and ā¤where should I buy it?
This is an OEM Frigidaire part used on specific Frigidaire/affiliated models. Always ā£confirm compatibility by checking yoruā refrigerator’s model number against ā£the part reference āor crossāreference lists from Frigidaire or āan authorizedā£ parts dealer. Buyā from Frigidaireā¢ parts distributors, authorized appliance parts retailersor reputable online ā£sellers to ensure you receive a genuineā or properly specified replacement.
Insights and conclusions
The 5303918568 Frigidaire defrost thermostatā¢ plays a central role in maintaining reliable refrigeration by monitoring evaporator temperature and ā¤initiating theā defrostā£ cycle when needed. By regulating when the defrost heater operates, this thermostat helps preventā¤ excessive frost buildup on the ā¢evaporator, supports consistent internal temperatures, āreduces strain on the ācompressorandā contributes toā£ overall āenergy efficiency andā food safety.
As similar symptoms canā¤ stem from several components, accurate diagnosis is essential before replacing the thermostat. When the 5303918568 is ā¢identified as the cause of defrost issues, timely replacement with theā correct part and proper installation restores performance, reduces energy wasteandā¤ helpsā avoid further component damage. For best resultsā¤ and safety, consider replacement by a qualified technician or follow manufacturer guidance when choosing and installing replacement parts.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
