240338001 Frigidaire Refrigerator Gallon Door Bin⤠is a molded âŁdoor shelf designed to hold oneâgallon containers and other tall items within the inner door⤠of compatible Frigidaire refrigerators. As a removable plasticâ storage bin,it is a nonâelectrical,structural accessory that attaches to the door liner via snapâin retainer clips,mounting rails,or screws and provides organized storage in the appliance door cavity.
Functionally, the bin interfaces with the door liner and its retention hardware âand transmits loads from stored contents to⢠the door assembly; it does not participate in the refrigerationâ cycle but can influence door balance, hinge loadingand⢠gasket sealing when heavily loaded or improperly installed. Typical engineering considerations include material selection (injectionâmolded thermoplastic chosen for impact and cold resistance), dimensional tolerances for snapâfit features, edge⢠and lip geometry to retain liquidsand the relationship of bin placement to door seal and shelf clearance. Technicians⢠need to account âfor load paths,clipped or screwed mounting points,and potential thermal â˘contraction or embrittlement over time when assessing fit and function.
In the article you will find a technical overview of the part’s function and common mounting methods,â guidance on determining compatibility with specific refrigerator models, typical failure symptoms (cracking, warping, broken clips, saggingor interference with the door seal), practical troubleshooting checks to⣠isolate mounting or damage issuesand considerations for replacement including verifying retention feature geometry, material conditionand whether to âuse OEM or âcompatible replacements. The discussion is focused on technical⤠inspection âŁand replacement considerations relevant to technicians, engineersand appliance owners performing diagnostics or repairs.
Table of Contents
- Functional Role, Load capacityand Structural Requirements ofâ the refrigerator â¤Door Gallon âŁBin
- How the 240338001â Frigidaire Refrigerator Gallon Door Bin Integrates with door⢠Shelving, Retention âClipsand Seal Interfaces
- Common Failure Symptoms and Diagnostic Indicators: Cracks, Retention Lossand Mounting-Point wear
- Replacement Considerations, Compatibility⣠Verificationand Installation Procedures for the Gallon Door Bin
- Q&A
- Insightsâ and Conclusions
Functional Role, Load Capacity,â and Structural Requirements of the Refrigerator Door Gallon Bin
The 240338001â Frigidaire Refrigerator Gallon Door Bin functions as a⤠door-mounted shelf⣠engineered toâ retain⢠and organize large liquid containersâ while transferring their loads into the door liner and hinge structure.Itsâ primary mechanical role â˘is to support the static weight of one-gallon containers (one US gallon of water âweighs approximately 8.34 lb â¤/ 3.78 kg) plus provide sufficient⣠margin for⢠dynamic loads that occur when the door is opened or closed. Compatibility requiresâ the bin’s clip spacing,rail engagement geometry,and retaining lip profile to match the refrigerator’s inner â˘door tooling; mismatched clips or incorrect rail tolerances â˘can⣠concentrate stress at the attachment points,causing premature cracking or detachment under repeated loading. Technicians replacing this part should confirm model âfitment and inspect door rail condition before installation to ensure that load paths remain intact and that âthe bin seats â˘flush â˘against the door liner.
Structurally, theâ bin must combineâ stiffness âand impact resistance at âŁrefrigeration temperatures, typically achieved with molded thermoplastics such as polypropylene or impact-modified ABS,⣠with localized ribbing and controlled wall thickness to⤠resist bending and creep. Mounting clips and hinge-engagement features are âthe critical load-bearing details and should be produced to tight dimensional⤠tolerances âto avoid bearing-edge stresses; fillets andâ generous radii at clip roots reduce stress concentration. In⣠practical terms, distribute heavy loads (glass bottles,⣠multipleâ full jugs) across the bin rather than concentrating them at one endand inspect the bin for hairline cracks, deformed clipsor crazing around fastener features as part of routine maintenance-these symptoms indicate â¤reduced â˘structural capacity and the need âfor replacement.
- Key features to inspect âor verify: mounting clip integrity, retaining-lip geometry,â wall thickness and ribbingand absence of cracking at stress points.
| Item | Description |
|---|---|
| Reference load | One US gallon â 8.34 lb (3.78⣠kg); bin should support this plus margin for dynamic loads. |
How the 240338001 Frigidaire Refrigerator gallon Door Bin Integrates with Doorâ Shelving, Retention Clipsand Seal⣠Interfaces
The 240338001 Frigidaire refrigerator Gallon Door Bin engages the âdoor linerâ through molded â˘mounting bosses and rail pockets that accept the bin’s tabs and âsnap-fit hooks. The bin transfers⢠vertical loads from bottles and jugs into the door via these contact points; properly sized clearancesâ and clip stiffness control â¤lateral movement and prevent contact with the â¤door gasket. External forces-such as â¤heavy containers or repeated door slams-are reacted at the clip-to-boss âinterface, â¤so mechanical wear or plastic creep at those locations increases play and changes the intended⢠load path, potentially affecting adjacent âshelving and seal performance.
- Mounting tabs and boss pockets: primary load-transfer points
- Retention clips: provide snap-fit retention and defined retention force
- Shelf rail engagement: ensures lateral alignment and stackingâ with other door shelves
- Seal interface: gap and compression against the gasket control â¤moisture âand noise
Service technicians verify compatibility and fit by checking for⢠even seating, consistent clip engagementand minimal gasket distortion. typical failure symptoms include sagging under nominal load, audible âŁrattle during door operationand localized condensation where a misplaced bin disturbs the gasket seating; these indicate worn clips, deformed tabsor mismatched replacement parts.â During installation or troubleshooting, apply controlled upward force on the bin to confirm retention, inspect bosses for cracking or elongationand replace the bin or clips with the⤠correct OEM part if tolerances exceed⣠factory specification⣠to restore correct alignment and seal interface behavior.
| Item | Description |
|---|---|
| Material | High-impact thermoplastic (typical ABS) with molded tabs |
| mounting method | snap-fit âtabs âŁinto molded door bosses; retention clips provide locking force |
| Primary function | Support gallon containers and maintain âlateral alignment with door shelving |
Common Failure Symptoms and Diagnostic Indicators: Cracks, retention Lossand Mounting-Point Wear
The 240338001 Frigidaire Refrigerator Gallon Door âBin serves as a load-bearing storage shelf on the refrigerator door and is typically molded from rigid thermoplastic. Common failure modes âare localized cracking⣠across the front retention lip, deformationâ or â¤thinning of the retention surface that holds containersand wear or breakage at the⤠mounting bosses or pegs that âsecure the bin to the door frame. Cracks commonly initiate at stress concentrators such as corners⢠around screw bosses⤠or the junction between the mounting⤠peg and the bin body; under repetitive loading (for exampleâ repeatedly storing a full gallon jug), these cracks can⢠propagate and reduce the bin’s ability to retain items or resist impact during door movement.
Technicians should evaluate both static and dynamic indicators: look for hairline⢠fractures visible with raking⣠light, check for excessive flexing of the retention lip under a typical loadand inspect mounting points for rounded or⤠fractured pegs that allow lateral play. Functional⢠symptoms include bins that shift or detach when the door is⢠opened, containers tipping outwardor audible creaks when loading items. For field diagnosis,gently load the âbin â¤with a representative weight and observe for⤠permanent deformation,and compare â¤mounting geometry against the âŁoriginal⣠specification to confirm âcompatibility before âreplacing the âpart.
- Visible hairline cracks along the front or underside of the bin.
- Loss of spring-back or excessive flex in the retention lip under load.
- Play âor movement at the mounting pegs/bosses âindicating wear or breakage.
- Rattling or vibration when the door is opened or closed.
| Item | Description |
|---|---|
| retention lip | Surface that engages container rims; signs of thinning, crackingor⤠permanent set indicate retention loss. |
| Mounting âpeg/boss | Attachment feature to the door frame; rounded or fractured pegs allow lateral â¤movement or detachment. |
Replacement⤠Considerations, compatibility Verificationand Installation Procedures for the Gallon Door Bin
The 240338001 Frigidaire Refrigerator Gallon Door Bin âfunctions as a load-bearing storage shelf integrated intoâ the refrigerator door liner;⣠its geometry and molded mounting tabs transfer the âweight of gallon containers toâ the door structure rather than to âthe thin plastic bin walls alone. The bin’s behavior â¤under load⣠depends on tab⣠engagement, material âproperties (in most cases rigid polystyrene â˘orâ ABS)and temperature-related embrittlement – repeated flexing or cold-inducedâ cracking typically originates at the tab roots or the front lip where bending stresses concentrate.verify⢠the refrigerator model number and mounting geometry before ordering: two bins with similar â¤outer dimensions can have different tab spacing or clip designs that will not engageâ the liner pockets correctly, so check the appliance model â˘plate or compare tab-to-tab measurements against the replacement before installation.
Installation is a low-torque, alignment-focused âprocedure: remove contents, lift the bin slightly to disengage the lower lip, then tilt the top away âfrom the door to release rear tabs and slide the bin free; reverse these motions to install the new bin, ensuring the⢠rear hooks seat fully into the liner pockets and the front lip â¤snaps into âthe bottom rail. If the bin will not seat, inspect for âiceâ buildup or âplastic deformation in the liner pockets, â˘warm the â¤area to clear frozen condensateand verify that mounting tabs are not rounded or broken; support the bin momentarily during the seating operation to avoid overstressing tabs. After installation, load âincrementally â¤and inspect for any visible deflection or crack initiation at tab⤠roots – replacing the bin before catastrophic failure preserves the door liner and prevents damage to stored items.
- Check model plate and âŁcompare tab⢠spacing to replacement part.
- Measure bin depth⣠and front-lip engagement to confirm fit.
- Inspect liner pockets for brokenâ clips, iceor debris.
- Install by lifting, tilting⢠to disengage/install, then press front lip until it seats.
- Test âŁwith gradual loading and recheck tab seating after first use.
| Item | Description |
|---|---|
| Part number | 240338001 |
| mounting type | Snap-in âmolded tabs to door liner pockets |
| Material | Rigid thermoplastic (commonly ABS or polystyrene) |
| Common failure modes | Tab-root cracking, front-lip fracture, deformation from overloading |
| Fit verification | Compare tab-to-tab spacing and liner pocket geometry; confirm withâ the refrigerator model plate |
Q&A
What isâ partâ 240338001 and which refrigerators does it fit?
Part 240338001 is a replacement gallonâsize door bin â¤(door shelf) manufactured for Frigidaire/Electrolux refrigerators. It is an OEM⤠style door bin used to hold tall items such as gallon jugs.Fit varies by model year and series – always verify compatibility â˘by checking your refrigerator model number against the part number on âthe manufacturer parts lookup or â¤with an authorized partsâ dealer before ordering.
How do⤠I remove and install the 240338001 door bin?
Most frigidaire⢠door bins snap into molded retention slots on the door liner. To remove: empty the bin, lift the front edge slightly and pull the bin straight â˘outward or upward depending on the retention style.To install: align the bin’s rear hooks or tabs with⢠the door slots âand press firmly untilâ it⢠snaps into place. No special tools are normally required; if there are additional screws or a retainer, remove them first with a screwdriver and reattach after installing the new â˘bin.
Can the 240338001 bin safely hold a oneâgallon milk âjug?
Yes – the bin is⢠designed as a âgallonâ door bin and is intended to hold gallon containers such as milk or juice.However, avoid overloading multiple full gallon jugs or exceeding the bin’s support if the mounting tabs or adjacent bins are worn or damaged. If you notice sagging orâ broken tabs, replace the bin (or the door liner/clips) before loading heavy items.
What should I doâ if the replacementâ bin won’t stay in place or its mounting tabs are broken?
If the bin won’t seat properly, inspect the door liner slots and the bin’s tabs for cracks or worn edges. âŁSmall broken tabs sometimes can be repaired temporarily with foodâsafe epoxy, but the recommended fix is to replace the bin. If the slots in the door liner are damaged, you may need a door liner repair⣠kit or to replace the door liner assembly.Make sure the âbin â˘you purchased âis the correctâ part for your model – incompatible âbins can fail to engage correctly.
Is the 240338001 an OEM part or are aftermarket versions available?
Part⤠number 240338001⤠refers to âŁthe OEM replacement used by Frigidaire/Electrolux. Aftermarket/thirdâparty bins that fit the same models may â˘also be available. OEM parts guarantee compatibility and finish match; aftermarket bins can be â˘less expensive but may vary slightly in fit or material. Buy from reputableâ sellers and check return policies if fit â¤is critical.
How doâ I clean the⣠240338001 door bin?
Remove the bin from the door and wash with warm water and mild dish soap.Rinse and dry thoroughly before reinstalling. Avoid abrasive⢠scouring pads that can scratch the plastic and avoid high heat â(do notâ place near direct âŁheat or in a highâtemperatureâ dishwasher âŁcycle) as excessive heat can â¤warp the plastic. If the manufacturer’s⢠documentation for your refrigerator specifically states dishwasher safety for door bins, the top rack on a lowâheat setting is usually safest.
What if the colorâ or finish doesn’t match âmy other door bins?
OEM replacements generally match the⢠original finish for⤠the model and production run, but there can be slight variances between production batches or if earlier parts have faded with age. If color match is significant, source the part through the manufacturer or an authorized dealer using your exact model and serial number. Aftermarket bins may have more â˘noticeableâ color or⣠texture differences.
Where⣠can I buy part 240338001 and does it come⣠with a⤠warranty?
You can buy 240338001 from Frigidaire/Electrolux parts stores, âauthorized appliance parts dealersand many online retailers. Warranty policies⤠vary by seller;â OEM parts obtained through the â¤manufacturer or authorized dealers commonly include a limited warranty (check⤠theâ specific terms). keep your purchase receipt and⢠theâ refrigerator⣠model/serial number when buying so you can validate⢠compatibility and⢠warranty coverage.
Insights âand Conclusions
The 240338001 Frigidaire refrigerator gallon door bin serves âŁa straightforward but important ârole in everyday⢠appliance use: it provides secure,organized storage for large containers and frequently used items on the refrigerator door,helping maximize interior space and maintain convenient⣠access. As âŁan âOEM-designed component, it is sized and shaped to integrate with the door’s mounting system so that items remain stable during normal opening and closing of âthe door.
Proper diagnosis and timely⤠replacement⢠of a damaged or failing door bin â˘are importantâ to preserve functionality and⢠safety. Cracks, warped mounting tabsor a loose fit can lead to spills, compromised storage capacityor interference⣠with â˘doorâ closure; identifying⣠the bin as the source of these issues before replacing it avoids unneeded repairs. when replacement âŁis required, selecting the correct 240338001 part and⣠following manufacturer guidance or using a qualified technician helps ensure proper fit, reliable performanceand minimizes the risk of further damage.
Maintaining intact door storage components like the 240338001 gallon bin is a cost-effective measure that âsupports the refrigerator’s usability and institution. Routine inspection and replacing the part when âinspection indicates wear or failure helps restore full functionality and contributes to the appliance’s âlong-term, trouble-free operation.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
