The âŁWD26X10013 GE⤠Dishwasher Motor & Pumpâ Assembly⢠is⤠anâ integrated electric â˘motorâ and centrifugal pump unit used in GE dishwashersâ to move â˘washâ and/or drain water through the machine. As âa mechanical-electrical assembly⢠it typicallyâ comprises a sealed⣠motor,â impeller(s), housing and mountingâ interfacesand electrical connectors;â it â˘is⣠installed in the dishwasher sump area where it couples to the plumbing that⣠feedsâ the⣠spray arms and drain path.
Within the appliance the motor and pump⢠assembly provides â¤the primary hydraulic force for recirculation of washâ water and, â¤in some models, âcontributes to draining. â˘It interfaces directly â¤with the⣠dishwasher control circuitry (relay or solid-state drive),â the sump and spray-arm plumbing, âinlet and drain hosesand safety devices such as float switches or pressure sensors. Proper operation depends on electricalâ supply and âcontrol signals,⢠intact shaft seals and bearingsand unobstructed impellers and plumbing; failures in any â¤of⣠these â˘sub-systems will affectâ waterâ flow, pressure and leak⤠integrity.
This article⢠will explainâ the WD26X10013 âassembly’s functional purposeâ and typical electrical/mechanical specifications, how to âverify compatibility with specific dishwasher models, common failure symptoms to recognize âŁ(such as loss of âcirculation, excessive noise, âŁleakage, âor tripping â¤protections), step-by-step troubleshooting checks a technician can â˘perform (electrical⢠tests, impeller inspection, â¤obstruction clearing, seal â˘assessment),⤠and practicalâ replacement âconsiderations such as⤠part âŁverification, gasket⣠andâ mounting âŁreuse, wiring⤠connections and safety precautions to observe duringâ service.
Table â¤of Contents
- Functional âRole of âŁthe âMotor andâ Pump â¤Assembly in⣠Dishwashing Cycles and Water âManagement
- how the WD26X10013⤠GE⢠Dishwasher Motor &â Pump Assembly Operates:⤠Electrical, Mechanical and Fluid-Dynamic Principles
- Common Failure Symptoms and Diagnostic Indicators: Noise,â no-Drain,â Low âŁPressure, â¤andâ Electrical Fault Codes
- Compatibility,â Replacement and Installation Considerations with Troubleshooting â˘Procedures and Post-Install Testing
- Q&A
- Keyâ Takeaways
Functional Role ofâ the Motor and pump Assembly in Dishwashing Cycles and Water Management
The WD26X10013 GE Dishwasherâ Motor & âPump âAssembly combines the recirculation â¤and drain pumpingâ functions intoâ a single⣠serviceable unit âthat mounts beneath the wash tub. During a⢠wash âŁcycle theâ motor drives an⢠impeller⤠that pulls water from the âsump and forces itâ through the spray arms âat the required âŁpressure; âduring drain phases the assembly either reverses flow âor âactuates â¤an internal drain impeller âŁto âevacuate water to the household drain. The assembly includes the electric⤠motor, impellers, mechanical seals and⣠the housing interfaces for the wiring harness âand control-board signals,⣠so correct electrical connections, sealing surfaces and alignment with the tub are criticalâ for reliable operation⢠and compatibilityâ with specific GE dishwasher models.
Operational behavior⢠and practical diagnosticsâ focus on hydraulic âperformance, mechanical⣠wear andâ electrical continuity. âTypical symptoms of a⤠failing unit include⣠low spray pressure (wornâ or damaged impeller), loud bearing noise,â inability to drainor fluid leaks âŁat the sealâ area; technicians commonly confirm faults by inspecting for âblockages,â manually turning the impeller, measuring motor windingâ resistance with âa multimeter, âand verifying â¤correct supply voltage during⣠a running cycle.Replacement⤠requires⣠matching the exact part number or âapproved OEM equivalents to ensureâ correctâ mounting points, âconnectorâ types and pump flow characteristics;⣠reinstall with new gaskets and verify⤠that âthe sump is free of debris that can ricochet and âŁdamage the impeller or seals.
- Common failureâ indicators: reduced spray pressure, unusual noise, persistent water in tub, âvisible leaks.
- Speedy checks: spin â¤impeller by hand, âinspect for foreign â˘objects, measure⣠motorâ windings for â¤continuity,⤠confirm voltage at connector during cycle.
- Replacement considerations: confirm model compatibility, replace⤠sealing components, retest hydraulic and electrical operation after install.
| Item | Description |
|---|---|
| Motor⤠Voltage | Typically 120 VAC â¤(verifyâ on data â¤plate âŁfor âspecific model) |
| primary Failureâ Modes | Impeller wear/clogs,⣠bearing â¤failure, seal leakage, electrical⣠winding faults |
| Mountingâ Interface | Specific flanges and harness connectors-match OEM partâ number â˘for fit |
How theâ WD26X10013 GE Dishwasher Motor⤠& Pump Assembly Operates:⢠Electrical, Mechanical and⢠Fluid-Dynamic Principles
The WD26X10013⣠GE Dishwasher Motor & pump Assembly âŁcombines an electric drive⢠and âone orâ more centrifugal âŁimpellers to provide both ârecirculation â¤and drainage functions âinside the dishwasher sump.Electrically, the⣠assembly is driven by an âŁAC⢠motor that is controlled by the appliance⣠control⤠board or relay; when⣠voltageâ is applied the rotor produces torque via interaction with⢠the stator windingsand thermal protection or⤠internal overloads limit current to prevent winding â˘damage. Mechanically, â¤the motor shaft is coupled to impellers through a molded â˘hub âand âŁsealed shaft â¤area; bearings and elastomeric seals maintain alignment and prevent water ingress. From a fluid-dynamic standpoint âthe âimpeller⣠geometry produces high volumetric flow at⢠modestâ pressure head suitable for spray â¤arm delivery, whileâ a separateâ drain impeller or pump âŁpath â˘provides higher⣠head âforâ moving water through âthe drain hose. Typical real-world behavior includes a steady current draw during normal recirculation, a⤠measurable increase in âamp draw under âblockage, âand⢠audible changes when bearings or⣠impeller vanes âare damaged.
Technicians diagnose⢠performance issues âby âcombining âŁelectrical and hydraulic checks:⢠confirm supply voltage⣠andâ motor continuity, âmeasure âoperating â¤current against specification, âinspect the impeller for debris or âŁerosion, âand verify that inletâ screens⤠and⢠check valves are⢠clear. âPractical compatibility considerationsâ include âmatching mounting flange,electrical âŁconnector pinout,and impeller orientation when replacing the unit; an OEM or correctly⤠specified aftermarket unit must match â¤these mechanical and⤠electrical interfaces to avoidâ fitment or â˘control problems.Commonâ symptom-to-cause âcorrelations are straightforward examples – low spray pressure usually indicates impeller wear or partialâ blockage, a âharsh grinding noise points to bearing or foreign-object damageand a⤠motor â˘that hums but does not⣠turn typicallyâ indicates a seized shaft or internal⣠electrical short.
- Common symptoms: lowâ spray/poor cleaning, humming with⤠no rotation, excessive âŁnoise, leaks âatâ motor seal.
- Quick checks: continuity of motor windings, amp draw under load, impeller âfree-spin and visible damage, inlet filter clearance.
| item | Description |
|---|---|
| Primary function | Circulate wash water through spray arms âand provide drain flow â˘when commanded. |
Common Failure Symptoms and diagnostic Indicators:⢠Noise, No-Drain, Low Pressure, âŁand Electrical âFault Codes
The â WD26X10013 GE Dishwasher Motor â& Pump âAssembly serves as the hydraulic and⤠mechanical heart⢠of âŁmany âGE dishwashers, providing both recirculation pressure for cleaning and the mechanical action for draining. When functioning correctly âŁthe assembly spins⣠the impeller(s) to generate flow⣠and operates âthe drain path through a separate pump or integrated chamber; compatibility with specific âmodels depends on⤠sump geometry and âelectrical connector⢠configurations. Mechanical â˘failures commonly presentâ as unusual noise (grinding, rattlingor highâpitched whine) from⣠the sump area, reduced sprayâ pressure across the wash â˘arms from an â˘eroded âŁor clogged impellerorâ a complete inability to âŁremove wastewater due to a seized âdrain rotor or obstructedâ chopper âassembly. Foreign debris, worn bearings, âŁdamaged impeller finsand⢠compromised âŁseals are practical⤠examples â˘ofâ faults that âalter hydraulic performance âwithout â˘necessarily showing âexternal damage to the housing.
Diagnostic â¤differentiationâ relies on correlating symptom⢠characteristics âŁwith electrical âand mechanical tests:⤠a âmotor that âhums but does not â¤spinâ often⢠shows normal âline voltageâ at the âconnector but â¤elevated current draw indicating bearing drag or rotor seizure, while âan open winding will show⢠infinite resistance âon an ohmmeter and typically triggers âŁan electrical fault code in the âcontrol board. Noâdrain conditions shoudl be checked⢠for routing restrictions (kinked hose, clogged⢠air gap),â blocked pump inletor a â˘failed drain rotor; low âpressure⣠is best confirmed⢠by measuringâ flow atâ the washâ arms orâ inspecting the impeller and âinlet screen for erosion or â¤debris. Controlâpanel fault⤠codes that reference the pump or âmotor â˘generally⣠indicateâ an open â¤or⤠short⤠circuit, stalled rotoror âovercurrent event and âshould⤠be verified⤠by measuring voltageâ at the motor plug, âŁchecking continuity across motor windingsand observing inrush and running current with a⢠clamp meter âŁbefore deciding âto replace the WD26X10013 assembly.
- Noise (grinding/humming): foreign object in impeller, bearingâ failureor rotor contact.
- Noâdrain: clogged chopper/inlet, â¤stuck âcheck valveor failed⣠drain rotor/motor.
- Low pressure:â worn/eroded impeller, â˘partial blockageorâ air leak in ârecirculation loop.
- Electrical â˘fault codes: open/shorted windings,overcurrent⤠due to mechanical bind,or connector/wiring faults.
| Item | Description |
|---|---|
| Multimeter âcheck | Measure winding resistanceâ and continuity to detect open or âshorted motor windings. |
| Current draw | Use clamp meter to detect excessive⤠running or⢠stallâ current indicating â˘mechanical bind. |
| Visual inspection | Remove sump cover to inspect impeller,â inlet screenand chopper for debris or âŁphysical damage. |
Compatibility, â˘Replacement and⣠Installationâ Considerations with Troubleshooting âŁProcedures and Post-Install testing
The âWD26X10013 GE Dishwasherâ Motor⣠&⣠Pump âŁAssembly is⢠the combined wet-end âand drive unit⣠responsibleâ for both⢠recirculatingâ wash water and, âin many models, providing the âdrain âfunction. Compatibility checks should includeâ mechanical mounting âpoints, inlet/outlet orientationsand âthe electrical connector pinout;â the wet-end housing âmust match the âspray arm feed and drain hose routing on the chassisâ to avoidâ misalignment⣠or⤠stress on seals. Confirm that⤠replacement units⣠have the same impeller diameter âandâ rotation directionâ and that the motor⣠thermal protector and shaft âsealing arrangement match the original, asâ differences in impeller geometry or seal depth âcan alter⤠flow rateâ and cause cavitation âor leaks even when the unit⤠fits physically.
Troubleshooting⣠and installation⣠require âŁmethodical verification âŁbefore and after fitment. â¤Before â¤installation, â˘verify motor âŁwinding continuity and⣠insulation â˘resistance,⢠inspect the impeller for debris or damageand confirmâ the â¤drain âpathway is âclear.After mounting and âreconnecting wiring,⢠perform a controlled testâ run: power the assembly â¤briefly â˘to âcheck âŁfor correct rotation, listen â˘for bearing noise, verifyâ no âaxial play⤠on the shaft, measure running current â¤againstâ the specification,â and â˘perform a leak check under â¤pressure.Typical troubleshooting steps and symptoms⤠to watch for âare â¤listed below.
- no pump operation: verify supply âŁvoltage âŁat the connector, âcheck thermal cutout âcontinuityandâ measure winding resistance.
- Weak⣠spray or poor âdraining: â¤inspect impeller for⤠blockage, confirm âcorrect impeller size and⣠orientationand check for partial â˘obstructions⢠in hoses.
- Unusual noise orâ vibration: check shaft endplay, bearing â¤wearand correct seating of the pump âŁhousing.
- Post-install leak: torque housing fasteners âto specâ and ârecheck âseal face âŁalignment and hose clamp positions.
| Item | Description |
|---|---|
| Nominal Voltage | 120â V AC (verify⣠mains and âconnector âŁpinâ mapping) |
| Typical Running⣠Current | 0.6-1.5⢠A (measure⤠under load; motor age and blocking affect current) |
| Keyâ Mechanical Check | Impeller diameter, ârotation direction,â and housing inlet/outletâ orientation |
Q&A
What is⢠the WD26X10013 âmotor & pump assembly and â˘what does it do?
Theâ WD26X10013 is âan OEM â˘GE/Hotpoint dishwasher⣠motor and pump (sump) âassembly. It houses⤠the wash motor and pump impeller(s)⢠and the â¤sump â¤that directs water⢠inside the tub. Its âprimaryâ functionsâ areâ to â¤circulate wash water through â˘the spray arms during cycles and, on some models, assist with draining. Itâ includes the pump housing, motor, impeller âand internalâ seals/gaskets as supplied by the manufacturer.
How do I know⤠if the WD26X10013 assembly is⤠the problemâ when my dishwasher isn’t⢠cleaning or draining?
common signs of⣠aâ failing pump/motor assembly include: no waterâ circulation (dishes not being cleaned), loud grinding orâ humming noises during the wash âor drain, error codes related to water flow or pump, persistent âstanding water⣠after a cycle, âŁor visible leaks fromâ the sump area. Before âreplacingâ the assembly, check for clogs/foreign objects in âŁthe âŁfilter and⢠impeller area, âand verify power is reaching âthe motor⣠with a multimeter. If the motorâ hums but doesn’t spin or shows an⤠electrical short/ open⢠in the windings,the assembly is likely⤠bad.
How do I test the motorâ onâ the âWD26X10013 to confirm it is bad?
First,disconnect power to the dishwasher. Remove access to the sump per⢠the service manualâ and visually⤠inspect the impellerâ for debris⤠or damage. Withâ theâ assembly disconnected⢠from the wiring â˘harness, â˘use a⤠multimeter to check continuity acrossâ the motor terminals -⢠windings should read â˘as a low⢠resistance (not open). Also check for â˘a short⣠to chassis⢠(infinite â˘resistance expected). For â¤anâ operational test, with âcaution and â¤proper safety âŁmeasures, â˘you can measureâ voltage at the⣠motor⢠connector duringâ a wash/drain step (typically ~120â VAC on most GE units) to verify âŁthe control is sending â˘power. If control supplies voltage and the motor does not⣠run,⢠the motor is â¤faulty.
Is âthe âWD26X10013 â˘compatible with âmy GEâ dishwasher⣠model?
Compatibility varies by appliance⣠model and â˘production date. âWD26X10013 fits many GE and Hotpoint dishwashers but not⢠all.Toâ confirm fit, compare the⢠part number with your dishwasher’s service manual âor parts list,⤠or â˘enter âyour dishwasher âmodel ânumber on the parts supplier⢠or GE/Whirlpool parts⢠website. Also visuallyâ compare mountingâ points âand electrical connectors if you’re replacing âan older part.
What⢠tools â˘andâ safety steps are needed to replace theâ WD26X10013 assembly?
Tools commonly required:⢠flathead â˘and Phillips screwdrivers,â nut drivers or socket set (often 1/4″-5/16″ and 7/16″),â pliers, a multimeter for testing, â˘towels/bucket forâ water,⤠and⤠possibly a âputty â¤knife âfor clips. Safety steps: disconnect âelectricalâ powerâ at âŁthe â¤breaker, âturn off âand â˘disconnect âŁthe âwater⣠supply, drain any standing â˘waterand âwork on a stable surface. Beware of sharpâ sheet-metal âŁedges inside the dishwasher. Follow the dishwasher service â¤manualâ for specific â¤disassembly and reassembly instructions.
Do Iâ need to replace⢠gaskets or seals when installing âŁWD26X10013?
Yes – any time you⣠remove theâ sump/pump assembly youâ should inspect⢠and â˘usually⣠replace theâ seals/gaskets âŁto⣠ensure a watertight fit.⤠Many OEM replacement assemblies include âthe ârequired gaskets and âseals; if yours âdoes not, âpurchase the recommended seal â¤kit âor part numbers âfrom the manufacturer. Improper or reused seals areâ a commonâ cause of âpost-repair leaks.
What should I do after installing the⢠WD26X10013 to verify proper operation?
After installation⤠reattach all electrical connectors and hoses, restore water supply and power, than run a short âwash âŁcycleâ while monitoring forâ leaks,⤠unusual noisesandâ proper water flow from spray âŁarms. Check that the drain operation â¤completes and there is no standing water. Re-tighten any fittings if leaks âappearâ and âre-check electrical connections if the âmotor does not run.
How much does a WD26X10013 assembly cost⤠and isâ it worth repairing vs replacing the â˘dishwasher?
Prices vary by âŁsupplier and âŁregion; the OEMâ pump/motor assemblyâ typically ranges from a âmoderate â¤to âsignificant single-part⢠cost⤠(check current part â˘listings). Whether⢠to⢠repair depends âon dishwasher age and âoverall condition: for newer machines or those without other major issues, replacing the pump/motorâ isâ usually⢠cost-effective.For âvery oldâ units or those⣠with additional failures, replacement⣠of the entire âapplianceâ may â˘be more economical. Also check whether â¤the unit is âunder any manufacturer⣠or extended warranty before payingâ for âparts.
Key Takeaways
The⣠WD26X10013 GE dishwasherâ motor⤠and pump assembly is âŁa central component that powers water â˘circulation â¤and âŁdrainage within the appliance. By drivingâ the wash and drain pumps, it directly affects cleaning performance, water removal, noise⤠levels âand overall operational reliability. A properly functioning âŁmotor⤠and⤠pump assembly helps â¤maintain consistent âwash cycles and prevents issues such âas standing water, poor cleaning results⣠orâ intermittent operation.
As symptoms of motor or pump failure can mirror âother dishwasher âŁproblems, accurate diagnosis is essential before âreplacing the⣠assembly.â Confirming â¤theâ root cause-through visual inspection, simple electrical checks⣠and adherence to manufacturer service data-helps âavoid âunneeded parts replacement âandâ reduces the risk of secondary â˘damage. When⣠replacement is required, âusing⣠the correct, compatible⢠assemblyâ and following safe installation and testing procedures âwill restore âperformance and extend the appliance’s service life. Professional service⢠or careful adherenceâ to the manufacturer’s guidelines isâ recommended for â¤reliable, long-term results.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
