WE25M87 GE Washer LP Conversion Kit is a liquid-propane (LP) fuel⤠conversion assembly intended to modify teh fuel delivery components of specific GE âlaundry appliances so they can operate safely âŁand âefficiently on propane rather of natural gas. As a service kit it typically providesâ the mechanical and pressure-adjustment parts required for conversion-such â˘as âŁalternate orifices, regulator âadjustment componentsand the necessary installation hardware⢠and instructions-thoughâ technicians should always confirm the exact contents for the kit they have on hand.
inside the appliance the conversion kit’s parts interact directly with the gas supply, burner assembly, âmanifold and pressure-regulating elements. The kit changes meteringâ and â˘pressure settings so the burner receives the correct mass flow for the different energy density and âpressure characteristics of LP; this affects flame size, heat output, combustion stabilityandâ the performance of ignition and flame-sensing circuits. The conversion therefore touches⢠fuel plumbing, combustion air/venting considerations, safety valves and interlocksand⣠in some cases the appliance’s manifold⢠pressure regulator or pilot orifice configuration.
In this article readers will find a technical âoverview of the kit’s function, clear guidance on how to â˘verify compatibility with appliance model numbers, â˘and the common failure modes and symptoms that⢠indicate an improper conversion or degraded components. The article also â˘covers⣠troubleshooting steps and measurement points (manifold pressure, âflame characteristics, leakâ checks), practical replacement considerationsand the safety and code compliance checks a qualified technician should perform. Where appropriate the text highlights tools and â¤test procedures required to confirm a correct, safe conversion rather than offering step-by-stepâ instructions that must be followed only in accordance with the manufacturer’s service documentation and local codes.
Table â˘of âContents
- Function and Role of the WE25M87 âŁGE Washer LP Conversion Kit Components
- How the WE25M87 GE Washer LP Conversion Kit Interfaces with the Gas Valve, Orificeâ and Pressure Regulator
- common Failure Symptoms and diagnostic Indicators for LP Conversion Orifices and âSeals
- Replacement Considerations, Model Compatibilityand âStepâbyâStep Installation Procedures
- Q&A
- final Thoughts
Function and Role of the WE25M87 GE Washer LP Conversion Kit Components
The WE25M87 GE Washer LP Conversion Kit suppliesâ the⤠specific⣠gas-system hardware needed to convert the washer’s burners⣠and valve assembly from natural gas to liquid propane (LP). its primary functional⣠elements – main andâ pilot orifices,a dedicated regulator spring or pressure insert,and sealing components – work âtogether to change volumetric flow andâ manifold pressure so the burners receive the correct mass of fuel for LP. By replacing orifice sizes âŁand⢠altering the regulator spring characteristics, the kit⢠changes flow coefficients and seat pressures to restore proper air-fuel ratio, flame shapeand combustion stability for the LP fuelâ characteristics of higher energy density and different specificâ volume flow compared with natural gas.
In practice, the kit’s âcomponents alter discrete hydraulic and pneumatic parameters within the âappliance: orifices provideâ a fixed geometric⢠restriction that reduces volumetric flow, while the regulator spring or âinsert re-establishes target outlet pressure from the gas valve. Technicians verify⣠conversion performance by measuring manifold pressure with a manometer, inspecting flame appearance under load (stable, blue cone with â¤minimal yellow tipping)and performing leak and functional testsâ after reassembly.â Confirm compatibility âwith the washer’s gas valve âand burner geometry before using the kit; mismatched orifice â¤sizes or⢠regulator parts can cause weak flames, sootingor elevated CO levels. Typical field procedures include replacing âŁthe orifices âand spring, torqueing fittings to specified âvalues, conducting a pressure checkand adjustingâ air shutters or flow paths if the flame pattern requires minor tuning.
- Main âorifice: sets burner mass flow⢠for LP operation.
- Pilot orifice: ensures reliable pilot flame with reduced flow.
- Regulator spring/insert: adjusts outlet/manifold pressure forâ LP.
- Gaskets/seals: maintain leak-tight connections after component changes.
- Instructions/labels: document conversion andâ provide torque/pressure targets.
| Item | Description |
|---|---|
| Main orifice | Fixed restriction that lowers volumetric flow to match LP’s required mass flow. |
| Regulator spring | Changes valve spring preload to produce the correct manifold⣠pressure for LP. |
| Sealing kit | Compression seals âŁand gaskets to prevent leaks at replaced âfittings and orifice holders. |
How the WE25M87 GE Washer LP Conversion Kitâ Interfaces with the Gas Valve, Orifice and Pressure regulator
The WE25M87 GE Washer LP Conversion Kit contains the lowâpressure orifice and associated fittings that directly interface with the appliance gas train: the gas valve outlet,â the burner manifold orificeâ portand the appliance âpressure regulator (or regulator setting). In operationâ the gas valve modulates supply according to âthe control signal âŁwhile the orifice limits volumetric flow âto the burners; converting to liquid propane requires installing a smaller,precisely sized orifice from⣠the kit and,where provided,fitting the kit’s regulator âadapter or replacing the regulator spring so that downstream manifold pressure is appropriate for LP. The mechanical fit and thread form between the kit components and the gas valve outlet must â¤match the installed valve body – the kit is intended to be used only on compatible âŁGEâ valve/manifold assemblies identified by the WE25M87â service documentation.
After installation the combined behavior of valveorifice and regulator determines flame characteristics and safety margins: the regulator sets the reference downstream â¤pressure (typical âLP manifold targets are near â 11 in. WC),the orifice sets the maximum flow at that pressure,and the valve provides on/off and modulation. Technicians should verify the conversion by measuring manifold pressure under steady burner â˘load, âŁinspecting flameâ shape (shorter, blue⣠LP flame with minimal yellow tipping),â and performing aâ pressure/flow check to âensure â¤the new orifice and regulator produce expected heat input withoutâ valve hunting or dropâouts. Practical checks: confirm part numbers against the appliance documentation, torque fittings⢠to spec, perform a combustible gas leak⣠testand document measured pressures⣠so field performance can be correlated to the installed hardware.
- Compatibility check: match valve/manifold stamp to kit documentation before installing.
- Orifice swap: replace natural gas⢠jet with kit LP jet and seal to specified torque.
- Pressure verification: âmeasure manifold pressure under load and adjust âregulator if required.
| Item | Description |
|---|---|
| Gasâ valve | Controls âon/off and modulation of supply; must except the kit’s outlet fitting and provide stable supply under LP conditions. |
| orifice | Precision jet that limits volumetric flow⣠to match LP energy density; smaller diameter thanâ NG jet to reduce flow at a given âpressure. |
| Pressure regulator | Maintains the downstream manifold setpoint (LP typically ~11 in. WC);â conversion may require âan adapter, spring change,⢠or replacement supplied in the kit. |
common Failure âsymptoms and Diagnostic Indicators for LP Conversion Orifices and Seals
The WE25M87 GE Washer LP Conversion Kit contains the orifices and seals used to adapt a gas-fired assembly to propane service; the orifice serves as the calibrated restriction that establishes the correct mass flow for the burner âwhile seals maintain pressure integrity at valve and manifold joints. In practice, LP conversion orifices are substantially smaller in diameter than natural-gas âorifices and must match the appliance thread, seat geometryand pressure-drop characteristics of the burner assembly. Seal âmaterials must be compatible with propane and the appliance operating temperatures-stiffening,swelling,or âchemical attack on elastomers will changeâ sealing performance and canâ createâ small leaks or pressure losses that alterâ combustion behavior.
- Yellow or sooting flame and increased carbon deposits – indicates an overly âŁrich mixture from excessive⤠flow or low primary air, often caused by incorrect orifice size orâ partial blockage.
- Intermittent ignition, extended flame-proving timesor weak flame – can result from reduced flow due to clogged orifice portsâ or pressure loss across a degradedâ seal.
- Audible hissing or detectable gas odor at joints – points to seal deterioration or⢠loose fittings; confirm by a soap solution or electronicâ leak â˘detector before further testing.
- Measured inlet/manifold pressure outside expected range⢠– use âŁa manometer to compareâ against appliance conversion specifications; mismatches⤠point to regulator issues, incorrect âŁorificeor leaks.
Diagnosisâ combines visual inspection,⤠simple bench measurementsand leak testing: visually âŁinspect orifices for âcarbon buildâup or erosion and verify the orifice diameter âwith a calibrated⣠gauge or pin set; test seals âfor compression and elasticity and replace if cracked, flattenedor hardened.Perform a controlled pressure check⤠with a âmanometer at the manifoldand use a soapy solution or gas detector⢠to isolate leaks âŁat âsealing surfaces after pressurization. When symptoms match the âindicators above, replacing the orifice and seals with components that match the kit’s specifications and confirming thread/seat compatibility typically restores intended combustion characteristics without further modification.
| item | Description |
|---|---|
| Yellow flame / soot | Likely rich mixture from â¤wrong orifice size, partial blockageor insufficient primary air; inspect orifice and measure pressure. |
| Gas smellâ / hissing | Seal failure or loose joint; perform soap-leak test and replace degraded seals⢠to restore leak-tight connections. |
Replacement Considerations, Model Compatibilityand StepâbyâStep Installation procedures
The WE25M87⣠GE Washer LP⤠Conversion âKit replaces the factory gas-delivery components so a gas-fired appliance can operate safely on âliquid petroleum (LP) instead of natural gas. The kit âtypically contains smaller orifices,a conversion label,and⣠installation instructions; these parts reduce flow and change the spray characteristics to match LP’s higher energy density and pressure behavior.Confirm compatibility by matching the appliance model number and the OEM part number: using the âwrong kit can â˘produce an over-rich or unstable flame, causing incomplete combustion, sootor safety interlock trips. For appliances that include a sealed combustion burner or⢠pressure regulator, the âinstaller must verify whether the regulator requires a spring or orifice change as part of the conversion.
Before beginning work shut off â¤allâ fuel and electrical supplies and relieve system pressure; then follow â¤a â˘controlled sequence: replace orifices and any regulator components, reinstall gasketsâ and labels, perform a static and dynamic â¤leak testand âvalidate combustion performance on a diagnostic cycle. Use a manometer to confirm manifold and inlet âŁpressures and observe flame shape andâ color across heat stages; measure exhaust for elevated â¤CO if available. Local codes frequently require a certified technician for gas⣠conversions and may mandate post-conversion documentation and labeling of the appliance, so retain the kit parts list and record the final pressure readings and test results.
- Verify model and âOEM part number before purchase.
- Shut offâ gas and⣠power; relieve pressure and ventilate the area.
- Swap orifices and regulator components per kit instructions.
- perform leak tests, pressure checksand combustion validation.
- Affix conversion label and document readings âfor code compliance.
| Item | Description |
|---|---|
| Orifice (LP) | Smaller⣠bore nozzle to reduce volumetric flow for LP combustion |
| Conversion⣠label | Permanent appliance âŁmarking indicating fuel type change and date |
| Instruction sheet | Sequenceâ of disassembly, part replacement, pressure checksand leak-test procedures |
Q&A
what is the WE25M87 LP conversion kit and what does it do?
The WE25M87 is a manufacturer-specified conversion kit intended to change⢠a GE gas appliance’s fuelâ system from natural gas to liquid propane (LP) or viceâversa, depending on⤠the kit version.A proper conversion kit supplies the⣠required orifices, regulator âŁparts⣠and instructions so the appliance’s gas valve and burner deliver the â˘correct pressure and flow for the alternate fuel.
Is the WE25M87 kit âforâ a washer? My appliance is a “GE washer.”
Washers (clothes washers) do not useâ natural gas or LP; gas âŁconversion kits apply to gas dryers and other â¤gasâfired appliances. If you have a gas dryer,â confirm the dryer model⢠number and⤠the kit part numberâ in the dryer’s installation manual or on GE/Whirlpool parts lookup to verify the WE25M87 is the correct kit for your specific dryer model.
How do I confirm theâ WE25M87 kit isâ compatible with my GE appliance?
Check the appliance’s model and serial numberâ against the parts listing inâ the owner’s manual or the manufacturer’s parts website. The â¤conversion kit packaging and instructions will list the specific models it supports. Do âŁnot attempt aâ conversion with a â˘kit that âisâ not explicitly listed as compatible with your model.
Can I install the WE25M87 conversion kit myselfor â˘do I need a technician?
Local codesâ andâ the manufacturer âŁtypically require conversions to be performed âŁby a qualified service technician or licensed gas fitter. Even if â¤you have⣠mechanical experience, a qualified technician ensures the correct parts are installed, regulator adjustments are⢠made properly, leak testing is performedand local code and safety requirements are met.
What parts and toolsâ are typically⢠involved in a conversion using this kit?
A conversion kitâ usually includes replacement burner orifices sized for âŁLP, a regulator or regulator cap/part needed for the alternate gas pressureand written instructions. Typical tools a âtechnician uses include screwdrivers, nut drivers, adjustable wrenches, a manometer or gas pressure gauge (for verifying manifold pressure),â and a leakâdetection solution or electronic gas leak âdetector. Always⢠verify âthe kit’s actual contents and required tools in the supplied instructions.
What are⣠the general⤠steps performed during a â¤conversion (high level)?
Highâlevel steps include: (1) turn off gas and electrical supply toâ the appliance, (2) access the gas valve/burner assembly per manufacturer âinstructions, â˘(3) replace the⢠natural gas orifices with LP orifices and install any regulator parts from the kit, (4) reassemble the appliance and restore gas, (5) perform a gas leak⢠test on all connections, (6) adjust and verify manifold/gas pressure and burner flame characteristicsand (7) runâ operational tests and document the conversion.Follow the kit instructions exactly and â¤comply withâ local requirements.
How do I verify the appliance is operating safely and correctly after conversion?
Postâconversion checks include: verify there are no gas leaks with an approved method,â confirm correct manifold/gas pressure using a manometer, observe âstable burner flame shape and color (steady âblue flame with minimal yellow tips for properly adjusted LP burners), check for proper heat output during⤠a test cycleand ensure venting and combustion â˘air are correct.If you detect strong odors, yellow or floating flames, sootor elevated CO â¤readings, shut off the appliance and have a qualified technician inspect â¤it instantly.
Will installing the WE25M87 â¤kit affect my warranty or appliance performance?
Using a manufacturerâapproved conversion kit and having a certified technicianâ perform the conversion typically preserves warranty coverage related to the conversion. Installing âanâ incorrect kit or performing an improper conversion may void parts of the warranty and can create unsafe operating conditions. Always use the OEM kitâ specified for your model âand keep documentation (receipt and⤠technician’s conversion tag) as proof of compliant service.
Final Thoughts
The WE25M87 GE Washer LP Conversion Kit plays a specific role in adapting compatible GE laundry appliances to operate on liquid propane where such a conversion is appropriate. Properly selected⢠and installed, the kit helps â˘ensure that the appliance’s fuel delivery and combustion parameters align with LP requirements,â supporting reliable performance, energy efficiencyand adherence to the manufacturer’s design âŁintent. Because the conversion affects core systems â¤of the appliance, using â¤the correct kit for the exact model is essential to maintain safe operation â˘and minimize the risk of malfunctions.
Accurate diagnosis and timelyâ replacement whenâ a⤠conversion kit is requiredâ are significant for both safetyâ and long-term appliance function. Technicians should⣠verify compatibility,assess the condition of related components,and confirm that conversion is⤠necessary before proceeding; if a kit â˘is damaged,missing,or incorrect for the model,replacement âshould be performed⢠in accordance with âmanufacturer â¤guidance and applicable codes. Engaging qualified service personnel for evaluation and installation helps protect performance,user safety,and regulatory compliance,making proper diagnosis⣠and replacement a prudent step whenever LP conversion is under consideration.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
