1129313 âŁWhirlpool Refrigerator Ice Maker Kit Round⤠Plug is a replacement⤠component used âwith Whirlpool ice maker âassemblies; it is⢠a circular electrical/mating plug designed to interface the ice maker module with the⣠refrigerator wiring harness.As â˘a discrete connectorâ element, theâ round plug âprovides mechanical retention⣠and electrical⤠contactâ points that carry powerâ and⣠controlâ signals between the ice maker and the appliance’s âŁcontrol systemsand inâ some installations âit also provides âŁa moisture-resistant seal where â˘the harness passes through the cabinet or mounting flange.
Inside the appliance the roundâ plug serves as the intermediate interface betweenâ the ice âŁmaker unit and the refrigerator’s control board, power supplyand âŁrelated subsystems suchâ as the water inlet â˘valve âandâ temperature sensing âcircuits. It typically mounts at the ice maker housing or âŁchassis and⢠participates in the controlâ loop that times fill cycles,⣠actuates the harvest heater or motor,⣠andâ reports presenceâ or error âŁconditions to the main controller. The â¤plug’s electrical â˘contacts, locking featuresandâ any sealing material âaffect signal integrity, âcorrosion resistanceand strain ârelief, so its â¤conditionâ influences both functional operation and serviceability âŁof⣠the ice-making system.
In this article readers willâ find â˘a technical overview of âthe plug’s⤠function and typical construction, guidance on model compatibility and⤠electrical âŁspecifications to check âwhen âreplacing âthe part,⤠common failure⢠symptoms such as âŁintermittentâ ice production, open or shorted circuits, visible corrosion or â¤broken latchesand step-by-step troubleshooting methods including visual inspection, continuity and voltage testing,⣠and⣠harness isolation. The articleâ will also cover â¤practical replacement considerations-correct part âidentification, connector orientation, sealing and ârouting best â˘practicesand when⣠to replace⤠the â˘plug versus the⣠entire harness or ice maker assembly-to help technicians, engineersand âappliance owners make informed repair decisions.
Table of contents
- function and⢠Role of the Ice Maker Kit Roundâ Plug in âRefrigerator⤠Ice Production and⤠Control
- How the 1129313 Whirlpool Refrigerator Ice Maker⢠Kit round Plug Works: Electrical, Mechanical and Water Interface
- Common Failure Symptoms,â Electrical Faults and Diagnostic Indicators for âthe Ice Maker Kit âŁRoundâ Plug
- Compatibility, âReplacement⤠Considerations and Installation procedures âŁfor Affected Whirlpool â˘Refrigerator⤠Models
- Q&A
- Insights and Conclusions
Function â˘and Role of the Ice Maker Kit Round Plug inâ Refrigerator Ice Production⣠and Control
The âŁ1129313 whirlpoolâ Refrigerator Ice maker âKit round Plug is âŁthe compact electrical connector that linksâ the refrigerator’s wiring âharness â˘to the ice â¤maker assembly and control electronics. Functionally, the round plug carries the control and â˘power conductors required for the ice makerâ to perform its cycle: it⤠transmits âsignals â¤from the main controlâ board to â¤the ice maker module â(motor/drive and harvestâ heater or heater circuit), provides a return path for temperature⣠or full-cupâ sensorsand routes⣠the âactuation signal âŁto âthe water âinlet valve during the fill portion of the⣠cycle.â The plug’s mechanical retention and contact geometry are designed to â˘maintain reliable electrical continuity in âthe cold, damp surroundings of the freezer; âa⢠damaged â˘or â˘corroded plug will commonly â¤interrupt âharvest or fill stepsâ and â¤can present⤠as no ice production, partial ejection,â or intermittent cycling.
Technically, â¤replacing or troubleshooting this connector requires verifying pin-to-function mapping and⣠ensuring connector âpolarity and housing typeâ match the refrigerator harness. Technicians should âŁinspect contacts âfor pitting, bent pins,â or insulation damage, âperform continuity âtests across expected circuitsand observeâ behavior during a â¤controlled service âcycle to âconfirm⣠which â¤signals are âmissing.⣠Practical examples: a⢠loose contact at the âmotor pin will âallow⢠fill but prevent â¤ejection, whileâ a âŁcorroded heater pin will allow the motor to run but⣠prevent ice release.⣠Use the checks⣠belowâ as⤠quick diagnostics â˘before full replacement.
- Common âsymptoms âand quick checks: intermittent cycle (wiggle test on plug), no â¤harvest (check continuity on heater/motor âpins), â¤no fill â(verify water valve signal âcontinuity).
| Item | Description |
|---|---|
| Part | 1129313 âwhirlpool Refrigerator Ice Maker Kit Round Plug âŁ- electricalâ connector â˘for ice maker⢠harness |
| Primary functions | Transmit control/powerâ for motor, âheater, sensor inputsand water valve âactuation |
| Service checks | Visual contact inspection, continuity/resistance tests, connector⢠pinâ alignmentâ and retention |
How âŁthe 1129313 Whirlpool⤠Refrigerator âIce Maker Kit Round Plug Works: Electrical, Mechanical â˘and Water Interface
The 1129313 â¤Whirlpool⢠Refrigerator Ice Maker Kit â¤Round Plug is the â¤electrical connector⤠that links the ice âmaker module to the refrigerator’s control âharness. It transmits the low-voltage control â¤signals âand power â¤required to drive the ice â˘maker’s⤠motor/geartrain and to actuate the water fill solenoid,⣠while also⢠providing â˘the circuit reference/ground.The âplug is â¤typically a â˘keyed, sealed round multi-pin housing designed to maintain pin alignmentâ and reduce moisture ingress; during service, technicians âshould inspect the housing âfor bent pins,â corrosion, âor loose⣠contacts â¤and⤠verify continuity and signal presence â˘withâ a multimeter before replacing the â¤ice maker â˘itself.
Functionally theâ plug enforces correct mechanical⤠orientation and reliable electrical contact; improper seating or damaged pins will âcause intermittent âcycles,⤠failure to open â¤the fill âvalveor a nonâresponsiveâ harvest cycle.â The water interface is controlled indirectly: the connector delivers the control⢠current that âŁenergizes the solenoid valve âallowing water into the fill tube and â¤into the⤠mold. Practical diagnostics include confirmingâ full engagement of the round plug, checking⤠for expected control voltages atâ the connector during⣠a cycle, measuring solenoid resistance,⤠and⤠observing whether the fill tubeâ receivesâ water when theâ ice maker signals âŁa fill-these checks â¤help distinguish connector/electricalâ faults âfrom mechanical â˘or water-supply failures.
- Common symptoms: no fill,â intermittent fillingor no harvest cycle-inspect connector first.
- Quick âchecks: visual pin inspection, continuity tests acrossâ pins,⣠and voltage measurementâ during an attempted cycle.
- When âto suspect â˘water-sideâ issues: â˘correct⤠control signals âpresent but no⢠water at the fill tube (valve orâ supply problem).
| Item | description |
|---|---|
| Connector type | Keyed round multi-pinâ electrical plug providing power and control âŁsignal paths. |
| Primary functions | Deliver⤠motor/geartrain power, activate fill⤠solenoid,â and return ground/feedback signals. |
| Typical âdiagnostics | Visual pin inspection, continuityâ andâ resistance checksand live⤠voltage measurement during cycle. |
| Compatibility ânote | Used with Whirlpool ice maker assemblies âsold⤠as the âŁ1129313 kit; confirm âmodel fitment âagainst appliance⤠documentation. |
Common âFailure âŁSymptoms,Electrical⤠Faults â¤and Diagnostic Indicators for the Ice Maker âKit Round Plug
The 1129313 Whirlpool Refrigerator Ice âMaker⢠Kit Round⢠Plug is the circularâ electrical connector that links the ice maker assembly to theâ refrigerator wiring harness,carrying⢠the power and âsignal circuits for theâ motor,heater,fill valve,and temperature sensing elements. Functionally, the round plug ensuresâ correctâ pin alignment⢠and a â˘sealed â˘mechanical interface; failures at this â¤connector âtypically manifest as loss âŁof one âŁor âmore ice maker⤠functions rather than an entire⤠applianceâ fault. Compatibility is largely resolute by theâ pinout and physical keying used on many Whirlpool-family models, soâ replacing only the plug or the kitâ is a common â˘repair when symptoms trace to corroded pins, broken wiresor an intermittent mating surface rather than a failed â˘iceâ maker module itself.
- No⤠ice production while â¤water supply⣠is OK – frequently enough indicates missing power⢠or â¤control â¤signals⣠at the round⣠plug.
- partial â˘cycles or intermittent harvest⤠– suggests⢠high-resistance contacts, âloose pins, âor âa cracked housing causing âintermittentâ connections.
- Heater activates but ice does not releaseor heater âshows open circuit on continuity test – pin-to-pin continuity or âŁheater element failure traced at the connector.
- Visibleâ corrosion, âŁbent pinsor â¤melted plastic at⢠the plug – mechanical⤠damageâ that frequently causes the âelectrical symptomsâ above.
| Item | Description |
|---|---|
| Power/Control Pins | should âpresent line/control âvoltage only during the appropriate âcycle â¤(verify with service diagnostics or a âliveâ cycle test). |
| Heater/Harvest Circuit | Expect a low-resistance path (continuity) with power disconnected; open or very âŁhigh resistance indicates a broken element or connector issue. |
| Fill Valve/water âSignal | valve actuation voltage appears âat the corresponding⤠pin â˘during the fill step; absenceâ suggests âwiring or connector break between⤠control board and valve. |
| Temperature⤠Sensor/Thermostat | Sensor shows temperature-dependent resistance; abrupt open orâ short at â¤the plug points to bad âcontact âor internal sensor âfailure. |
For⤠practical troubleshooting, first perform visual⤠inspection and wiggle testing withâ power removed toâ see if movement⢠changes continuityâ readings; next, measureâ resistance and continuity across âthe expectedâ pins with â¤the â¤connectorâ unplugged âto isolate broken conductors or high-resistance joints. With⢠the unit powered and in âŁa diagnostic or harvest mode,measure forâ the presence⢠of the appropriate voltage on âthe harness side âof the plug – if⤠voltage is present at the harness but absent at the ice maker,the round plug or short section âof wiring⤠is the likely âfault. Swapping with a known-goodâ harnessâ or⣠using aâ short pigtailâ to âbypass â˘the connector are effective confirmatory steps before replacing the ice maker orâ control board.
Compatibility,⤠Replacement Considerations and âInstallation Procedures for Affected⢠Whirlpool âRefrigerator Models
The 1129313 âWhirlpool Refrigerator Ice Maker Kitâ Round Plug serves as theâ electrical⣠interface â˘betweenâ the appliance harnessâ and the â¤ice maker module;â it uses a circular multiâpin â¤connector to route power and control signalsâ (motor, water âvalve,⣠heater/harvest control and sensor/thermostat inputs) rather than the⣠flat blade connectorsâ usedâ on some other assemblies.Compatibility is determined by âthree physical andâ electrical factors: plug shape and pin count, the pinâtoâfunction mappingand the mechanical mountingâ pointsâ for the⣠iceâ maker assembly. Technicians should compare the replacement kit’s âŁconnector âand pin mapping to â¤the refrigerator’s â¤harness and service literature before installing; â˘in some casesâ the physical connector matches but the signal assignments differ, requiring a factory harness⢠or⣠an adapter â˘harness to⣠prevent incorrect operation â(for example, energizing â¤a heater when a motor is expected).
Replacement and installation procedures emphasize safe verification âof electrical and âŁmechanicalâ compatibility followedâ by functional testing. Begin by disconnecting âmains power,â then access the âice maker area to confirm the round plug mates⤠correctly, visually inspect wire colors⣠and pin positionsand perform continuity and function checks⣠with a âmultimeter if pin⣠mapping documentation is not âŁavailable.After â¤mounting the assembly â˘and seating the connector, restore⤠power âand use âthe refrigerator’s diagnostic/test mode or⢠manually âŁcycle âthe ice maker⣠to confirm: the â˘motor turns, the fill valve actuates⤠forâ the correct durationand⢠the harvest sequence â˘completes without â˘error âcodes or leaks. Common postâreplacement issues to watch for include â¤a âpartially âseated connector, incorrect âŁpin mapping, âor harness âŁstrain at theâ connector which can⤠cause intermittent operation.
- Preâinstallationâ checklist: model number⤠verification, plug shape/pinâ count match, wire color/pin mapping confirmation, transfer of any sensors or brackets, power disconnected.
- Postâinstallation âŁtests: âŁcontinuityâ checks, diagnostic cycle run, âwater⢠fill volume and harvest âconfirmation, leak inspection.
| Item | Description |
|---|---|
| Connector type | Roundâ multiâpin electrical â˘plug used âto carry power⤠and control signals to ice maker |
| Pin â¤considerations | Verify pin count and function mapping (motor,valve,heater,sensor,ground) before âinstallation |
| Installation tip | Use OEM âharness or adapter when physicalâ mating is possible but signal â˘assignments differ |
Q&A
What is the 1129313 Whirlpool Refrigerator Ice Maker Kit Round â˘Plug and what does â¤it include?
The 1129313 is an â¤OEMâ Whirlpool ice â˘maker⤠kit âdesigned to replace⤠a failed⤠or missing â¤ice â˘maker assembly in compatible Whirlpool-built refrigerators. It typically includes â¤the ice maker assembly and âa wiring harness with a round-style plug that mates⢠to the refrigerator’s existing connector. Packaging can vary, so check the product âlisting or parts diagram for exact contents.
How do Iâ know⤠if this round-plug kit is â¤compatible âwith â˘my refrigerator model?
Check your refrigerator model number (usually on a sticker inside the fresh food â˘compartment⣠or behind a âgrille) and cross-reference it with⤠theâ OEM part numberâ 1129313 on the Whirlpool parts âwebsite or âŁan authorized âparts dealer. âŁCompatibility âcharts will show whether the âround⤠plugâ ice maker âis⤠the correct⣠replacement âŁfor your âspecific model and year. âŁIfâ in doubt, provide the full⢠appliance model numberâ to the â˘parts supplier.
Can âŁI⢠install the 1129313 ice maker kit âmyselfâ and what tools are required?
yes, â˘many homeowners âcan install thisâ kit. Typical tools are a Phillips screwdriver,⢠nut driver (usually âŁ1/4″ or 5/16″)and needle-nose⢠pliers. You should turn⣠off and unplug the⣠refrigerator (or switch off its breaker) and shut off the water supply before beginning. follow âŁthe kit instructions â˘or your model’s â¤serviceâ manual. If⤠you are uncomfortable working⢠with appliance wiringâ or water â˘connections, hire âŁaâ qualified technician.
What are the proper installation âsteps for the round plug ice maker?
Basic âsteps: 1) Unplug the refrigerator andâ shut off water supply. 2) Remove âthe freezer shelfâ or coverâ to access the ice maker. 3)â Disconnect⢠the old ice maker⣠by unplugging â¤its wiring âharness and removing âmounting screws. 4) Mount the new ice maker in place⤠and secure with screws. 5) Plug â˘the new harness into theâ refrigerator’s matching round receptacle (do not force).6) Restore âwater andâ power, âthen run a test cycle or allow 24 hours⣠for iceâ production. â¤Always follow⤠the specific âŁinstructions⣠supplied with the â¤part and your refrigerator’s service manual.
My replacement has a round plug butâ my refrigerator has a differentâ connector – what âshould I do?
If âthe connector shapes don’t âmatch, do not force or modify the refrigerator âŁwiring.Confirm you ordered the correct OEM part âfor⣠your model. Some â¤refrigerators used differentâ harnesses or adapters; your dealer can âŁadvise on the â˘correct âharness part number⤠or provide⤠a compatibleâ adapter. In many cases âyou will âneed a⤠different ice maker kit or a separate harnessâ replacement ratherâ than modifying factory wiring.
How can⢠I testâ theâ newâ 1129313 ice maker to â˘make sure it’s working afterâ installation?
After restoring⢠power andâ water, allow the ice âmaker to cycle; it may⣠take up to 24 âhours to⣠produce ice. For quicker testing,⤠consult your⢠service manual – many models have a diagnostic/test mode or aâ test terminalâ on the â˘wiringâ harness that will initiate a⣠harvest/fill âcycle when shorted by a jumper or⤠pressed.â Use the manufacturer’sâ recommended â˘procedure to avoidâ damage. Verify the fill â¤valve âoperates,â theâ tray fillsâ with⢠waterand the unit advances⣠through âthe harvest and eject steps.
What⤠common⢠problems should I troubleshoot if the newâ ice maker doesn’t make âice?
Check âthese âitems in⢠order: 1) Confirm water supply valve is open and âwater line âis not⤠kinked. 2)⢠Ensure the âinlet/fill valve is receiving power and â˘operating; if not,â checkâ for âa clogged filter or â¤faultyâ valve. â3) Verify⣠the â˘ice maker is level and properly mounted. 4) Check the freezer temperatureâ – it should be â˘aroundâ 0°F (-18°C) â¤for proper ice making. 5) â˘Inspect the mounting connector for secure electrical connection.⤠If⣠electrical, waterand temperature are correct and itâ still fails, the new unit could be defective or â˘a different refrigerator component (thermostat,â control board) mightâ potentially be at âfault.
Is the 1129313 anâ OEM part and is⣠it âcoveredâ by warranty?
1129313â is sold âas an OEM genuine replacement part when â˘sourced from Whirlpool or authorized dealers.Warranty coverage depends on the seller â˘and whetherâ you buy directly from Whirlpool or aâ third-party supplier. Checkâ the warranty terms⤠with the⢠vendor – OEM parts oftenâ carry a⢠limited warranty â˘forâ a set period, but labor and installation âare typically not covered unless â˘provided by theâ seller.
Insights and âŁConclusions
The⤠1129313 âWhirlpool Refrigerator Ice Maker⣠Kit âround⤠Plug servesâ as⢠a key componentâ in maintaining reliable ice productionâ by providing the necessary â¤electrical and⤠mechanical interface for the ice maker assembly. Properly functioning, this kit helps ensure consistentâ ice harvesting, prevents intermittent⢠operation,â andâ contributes â˘to the â˘overall efficiency and performance⣠of compatible Whirlpool refrigeration models.
Accurate â˘diagnosis of ice maker problems is essential before replacingâ theâ kit. â¤Identifying whether issues stem from the ice âmaker module, the round⣠plug kit,⣠the water supplyor control âcircuitry helps avoid âŁunnecessary parts replacement and â¤reducesâ downtime. â˘When testingâ indicates the round plug âkit is the source âof the failure, selecting the correct âreplacement part âand installing it according to manufacturer âspecifications preserves system compatibility and safety.
Timely, informedâ replacement of a faulty 1129313⣠kit can restore iceâ maker function and prevent secondary issues related to improper connections âor aging components. For users uncertain âabout diagnosis or⣠installation,consulting a qualified â¤technician ensures the⤠repair âis completed â˘correctly and maintains appliance⣠reliability over the long term.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
