316112005 Frigidaire âOven Range Anti Tipâ Bracket Kit is aâ steel mounting assembly provided to secure a freestanding oven or range to a fixed substrate â¤(floor or wall) to prevent unintended forward tipping. The kit typically includes a formed bracket, fastenersand âŁanchors sized for the appliance;â it is classified⤠as a mechanical safety âand restraint component rather than a functional appliance subsystem such as electrical or gas controls.
Within theâ appliance system the anti-tip bracket is part of the mechanical support architecture: it interfaces directly with the range chassis, the unit’s levelingâ feetand the building structure at the⢠rear or underside of the appliance. âWhen correctly installed and engaged, the bracketâ restrains rotational motion about the front feet that can occur when the oven door â˘is loaded or a user applies leverage⢠to an open door. Its performance therefore affects appliance stability,the distribution of static and dynamic loads through the cabinet and floor,and the stress seen â˘by attached â¤utilities (electrical cords,gas flex lines) and adjacent âcabinetry.
In this â˘article⤠readers will learn the intended function of the 316112005 anti-tip bracket â˘kit, the specific models andâ installation locations âwith âwhich it isâ compatible, common symptoms that indicate bracketâ failure or improper installation, diagnostic and troubleshooting steps toâ verify secure anchoring and correct engagement with the range chassisand practical replacement considerations including â¤selection of appropriate anchors for substrate, required hardware and clearances,â and basic â¤safety â¤precautions to observe during service.
Table of Contents
- Functional Role of the AntiâTip Bracket in Range Stability, Load Transferand User Safety
- Operational Mechanismâ of the 316112005 frigidaire Oven Range Anti Tip Bracket Kit within the RangeâtoâFloor Mounting Interface
- Indicative Failure Modes and Diagnostic Symptoms âŁof a Compromised AntiâTip Bracket Assembly
- Compatibility Matrix, Replacement âCriteriaand stepwise⤠Installation Procedures forâ the AntiâTip Bracket Kit
- Q&A
- The Conclusion
Functional Role of the AntiâTip Bracket in Range Stability,â Load Transferand User⢠Safety
The â316112005 Frigidaireâ Oven Range Anti Tip Bracket Kit provides a fixed mechanical anchor that⤠prevents a range from ârotating forward⤠under a tipping⣠moment.The âbracket mounts to âthe range frame and to the building structure (typically a wall stud or floor⣠substrate), creating â˘a controlled load path so âŁoverturning⢠moments applied to theâ applianceâ door or cooktop are transferred âinto the structure instead of âŁthe appliance cabinet. âIn normal use âŁthe bracket is passive; it only carries load onc the range begins âŁto pivot forward, at which point it engages and âlimits rotation by carrying⢠shear⢠and tensile forces âthrough its âfasteners.
Functionally,⤠the antiâtip bracket converts a potential overturning moment into⣠axialâ and âŁshearâ loads in the bracket⤠and into the supporting structure. âCorrect performance depends on secure attachment to structural framing with appropriate fasteners and on alignment with the range’s rear foot or frame so contact occurs before the center of â¤gravity extends⣠beyond the frontâ support. For technicians and installers this means verifying stud location,â using manufacturerâspecified fasteners âorâ equivalent anchors for the wall materialand checking âthat trim or flooring does not create a gap that prevents engagement.Practical examples include a⤠heavy cookware load on an open oven door or a child âclimbing on the oven door; in both cases the bracket arrests tipping but does not prevent lateral impact damage or sliding if floor anchors are not used or if the bracket is improperly installed.
- Primary role: resist overturning moments by transferring load to building â˘structure.
- Activation: passive-engages only⣠when range pivots forward⤠beyondâ designed clearance.
- installer checks: stud alignment, fastener type and lengthand bracket contact with range frame.
- Limitations: not a restraint for lateral collisions or unsecured â˘flooring; requires correct fastening to be effective.
| Item | Description |
|---|---|
| Attachment point | Bracket to range frame and to structural framing âor floor substrate to create⢠a continuous load path |
| Typical components | Steel bracket, mounting screws/bolts, wall anchors or lag screws per installation⣠instruction |
| Verification | Confirm engagement by measuring âŁclearance and testing âthat the range cannot pivot forward when fastened |
Operational Mechanismâ of⢠the 316112005 Frigidaire Oven Range Anti Tip Bracket Kit within the â¤Rangeâtoâfloor âMounting Interface
The 316112005 â¤Frigidaire oven Range Anti Tip Bracket âKit functions as⣠a dedicated mechanical anchor that couples the range rear chassis âto the finished floor or underlyingâ floor structure. In normal use the â¤bracket resists overturning moments generated when the oven âdoor is open or âwhen weight is applied to the door or cooktop surface by transferring those loads âinto the floor rather than the range leveling legs or cabinetâ joinery. â˘The bracket interfaces with a standardized rear mounting point âŁon the range â¤and is intended to engage a structural substrate so the range cannot rotate forward under a load; this â˘behavior reduces â¤the likelihood of âa tip eventâ caused by a sudden, offâcenter â˘load such âas âa heavy pot on an open door or a person leaning on the door.
The mounting interface isâ simple but must be executed to maintain the design function: âthe bracket is âŁpositioned against⤠the floor or subfloor and âŁfastenedâ with the appropriate screw or âŁanchor, thenâ mated âto the range’s rear mountingâ hole⢠or rear footâ bracket. Installers should verify the bracket is anchored into a structural element or an approved âmasonry anchor rather⤠than âonlyâ into underlayment; ⢠verify âengagementâ with solid floor framing â¤or an approved masonry â¤substrate to ensure the â¤bracket can develop the required resisting moment. In retrofit or uneven âinstallations the bracket allows small positional adjustments so it âcan be located âŁto engage the factory mounting hole without preloading the range frame; this accommodates common differences âin floor height, leveling leg â¤positionâ and finished flooring thickness. For practical context, technicians commonly fit the bracket before âfinal range leveling and use the bracket as the âŁlast attachment after setting the ârange into place and confirming⣠clearance for âthe antiâtip engagement.
- Features: stampedâ corrosionâresistant steel body, single ârear attachment⣠to ârange, floor anchorage point.
- Behavior: âŁtransfers overturning moment to floor substrate rather than range frame orâ cabinets.
- Compatibility: designed for Frigidaire ranges that use the⢠standard rear mounting interface and for many ranges âŁwithâ similar rearâmount configurations.
| Item | Description |
|---|---|
| Material | Stamped steel with corrosionâresistant finish |
| Fastening | Bracket-to-range uses the rear mounting hole;⣠floor âanchorage⢠requires âscrew or masonry anchor appropriate to substrate |
| Function | Resists forward rotation by⤠transferring load to a solidâ floor⢠substrate |
Indicative Failure Modes and Diagnostic Symptoms of a Compromised Antiâtip bracket Assembly
The antiâtip bracket assembly prevents a range⣠from rotating forward off its rear feet when the oven door is loaded⤠or when aâ user applies force to the door. The â¤316112005 Frigidaire Oven âRange Anti Tip Bracket⤠Kit is a replacement anchoring⤠assembly designed to engage the rear base of compatible Frigidaire ranges and secure to a floor or âwall fastener.⤠When âthe bracket, âanchor fastenersor mounting hardware areâ compromised – suchâ as âŁthrough bent bracket arms, undersized or missing anchors, strippedâ threadsor installation to âŁnonâstructural material – the effective pivot âpoint of the â¤range shifts forward and the appliance will exhibit increased forward rotation under load. Compatibility issues (incorrect bracketâ orientation, use on anâ unsupported modelor anchoring to subfloor rather than â¤a⢠structural member) change load paths and can mask a⣠failing bracket until⤠the range is loaded with cookware on â¤the open â¤door.
Common diagnostic symptoms are observable with a combination of visual inspection and simple mechanical tests:
- Excessive forward movement âor rocking â˘when the oven door is opened⤠and a standard load (e.g., a baking âtray) âis placed on it.
- Visible gapâ or separation at the rear â˘base where the bracket should abut the cabinet floor or wall anchoror a bracket that is plastically deformed or cracked.
- Loose, missingor stripped fasteners at âthe anchor point;⣠fasteners that turn without engaging âholding material⤠indicate failed âŁthreadsâ or inadequate anchorage.
- Audible creaks â˘or âmetal fatigue noises under small displacements,â and measurable change in tilt before/after tightening leveling â˘legs.
Use a controlled pull testâ (apply horizontal force âat the door⣠centerline) â˘and observe relative movement at âthe rear bracket and anchor to â¤isolate bracket failure from floor or â¤adjacent cabinetry movement.
| Item | Description |
|---|---|
| Loose âor missing fasteners | Fasteners that do not clamp the bracket to a â˘structural member; verify torque and âthread engagement. |
| Bent or âfractured bracket | Visible⢠deformation or cracks at âwelds/holes⤠reduce⤠load capacity and allow forward rotation. |
| Incorrect anchor location orâ substrate | Bracket attached to drywall, thin flooringor offset from stud results in insufficient holding strength. |
Compatibility Matrix, Replacement â¤Criteriaand Stepwiseâ Installation Procedures for the AntiâTip Bracket⣠Kit
The 316112005 âŁFrigidaire Oven Range Anti Tip Bracket Kit is a fixed mechanical â¤anchoring component designed to prevent forward tipping of a range by restraining the rear of the appliance to a secure mounting point in the cabinet, wallor floor. compatibility depends on the range chassis geometry (rear leg type and spacing),â the presence of factory âanchor points on the range rear paneland the âŁsite âŁconstruction (solid flooring, cabinetâ return depthand âwall âstud location). For example, freestanding Frigidaire ranges âwith exposed leveling legs commonly accept a floor-mounted⢠bracket that engages the leg, while slide-in units with a continuous cooktop may require a wall-mountedâ bracket that fastens into a rear chassis flange; confirm fit by matching rear-leg spacing and anchor-hole locationsâ against the kit’s template or compatibility chartâ before purchase or installation.
- Verify appliance model and physical rear geometry against âthe kit template.
- Disconnect⣠power and gas and move the range âclear ofâ the installation â¤cavity.
- Position and secure the bracket to the approved structuralâ surface using manufacturer-supplied fasteners or equivalent-rated hardware.
- Slide the range back, engage the bracket with the designated⣠chassis feature, then âperform a stability test by applying downwardâ pressure on the open door.
- Replace bracket if deformed, fasteners are strippedor after âany event that could have compromised the anchor (transport, heavy impactorâ repair).
Replacement criteria âfocusâ on the mechanical integrity of âthe bracket and fasteners: visible bending,broken welds,stripped threads,or missing components justify replacement because âthey⤠reduce pullout resistance. After installation, performâ a functional check by applying steady downward force to the open oven door to confirm the range âdoes not pivot forward; âŁif the range⤠moves, re-check fastenerâ seating, structural attachment pointsand compatibility of the bracket orientation. âFor field service, document⢠the installed bracket orientation and fastener types so future technicians can assess compatibility quickly during repairs or cabinet modifications.
| Item | Description |
|---|---|
| Compatibility | Depends on⤠rear⣠leg spacing, chassis anchor holesand installation type (floor vs wall) |
| Fasteners | Use manufacturer-supplied⣠hardware or equivalent rated for wood studs/flooring; avoid⢠self-tapping into thin sheet metal only |
| Functional Test | With range in â¤place, apply steady downward â˘force to open door; no⤠forward pivot indicates correctâ anchorage |
Q&A
what is the 316112005 Frigidaire Oven range AntiâTipâ Bracket Kit and what does âit⢠do?
The 316112005 kit⤠is anâ antiâtip bracket assembly intended for Frigidaire ranges. Its purpose is to secure the range âto the floor or wall so⣠the appliance cannot tip forward when weight is placed on an open oven door. this prevents injuries and damage by keeping the range anchoredâ in place.
Which ranges or models is part ânumber 316112005 compatible with?
theâ bracket is marketed for many Frigidaire ranges and some related brands. compatibility⣠varies by model⢠year and configuration, so always confirmâ fitâ by checking your âŁrange model number against the âparts list in the owner’s manual or the parts supplier’s compatibility tool. If in doubt, contact Frigidaire support â˘with⣠your â˘exact model number.
Does the kit include all mounting hardware, â¤or do I â˘need additional fasteners?
Most 316112005 kits include theâ metal bracket and basic fasteners (screws/anchors) intended for âtypical wood subfloors. Though, hardware can vary âby supplier and application. If you’re mounting to concrete, tileor an elevated platform you will likely need â¤appropriate masonryâ anchors or longer âŁscrews. Verify the kit contents before starting âand obtain the correct anchors for your floor type.
Can I use the antiâtip bracket on both gas and electric⤠ranges?
Yes. Antiâtip âŁbrackets are used on both gas and electric freestanding ranges.⤠The mounting method and âbracket location are the same; though, â˘take care when moving a gas range-shut âoff and disconnect⣠the gas supply perâ local codes and manufacturer instructions before sliding the appliance out for installation.
What âbasic toolsâ and materials do Iâ need to install the bracket?
Typical tools: tape measure, âpencil/marker, âdrill with appropriately sized âbits (wood or⣠masonry),â screwdriver or socket driver, leveland pliers. Materials: âthe kit (bracketâ and screws)and anyâ additional anchors required for â˘your floor⢠type (masonry anchors for concrete/tile; longer wood screws for platform). Have someone âŁhelp you reposition the range⢠when sliding â˘it back over the bracket.
How do I install itâ and â˘verify it’s installed correctly?
Basic procedure: 1) Pull the range out and unplug/disconnect electrical âand gas supplies as required.2) Position⢠the bracketâ onâ the floor or wall per the âmanufacturer’s template/location in âthe manual, mark and preâdrill as needed.3) Fasten the bracket securely to⣠the structural floor or wall framing usingâ appropriate anchors. 4) Slide the range back â¤until the â¤range’s rear leveling leg or engagement tab â˘fits into the bracket. 5) Test by gently âpulling forward on the top rear of the range â¤or placing weight on the open door-theâ range âshould ânot âtip. Always followâ theâ specific instructions in your owner’s manual.
What if âthe bracket doesn’t line up with the range’s leg⣠or⤠tab?
First,check the range’s leveling legs and overall position-adjust the legs so⤠the rear engagement âŁpoint is â˘at âthe correct height. If misalignment⤠persists, reâposition the bracket slightly within the allowed âmounting area,⣠ensuring it⢠still attaches⤠toâ structural substrate. âFor raised platforms, secure the âbracket to the platform framing, not just the surface. âIf you cannot achieve⣠engagement, â¤consult the âŁparts manual or a technician-do not operate the⣠range without a âŁfunctioning antiâtip device.
is installing the antiâtip bracket required by law or safety standards?
Yes. Manufacturers and safety standards (including UL requirements) â˘mandateâ antiâtip devices for freestanding ranges. Many âlocal building codes and the appliance’s warranty require the antiâtip bracket to be installed. It⣠is indeed a critical safety device-do not omit it.
The Conclusion
The 316112005 Frigidaire Oven Range Anti Tip Bracket Kit serves â¤a âcritical safety âŁfunction by securing freestanding ovens to the â˘floor or âwall and preventing tip-over incidents. Properly âinstalled, this OEM bracket helps â¤maintain appliance stability during normal⤠use and when doors âare opened, reducing⣠the risk of injury to⢠household membersâ and damage to the appliance. Its role aligns with manufacturer safety guidance⢠and⣠commonâ building-safety practices for large kitchen appliances.
Accurate diagnosis of an anti-tip hazard is essential:⢠inspect for missing, loose, bentor corroded components⢠and verify⢠that⢠the appliance remains firmlyâ anchored. When inspection reveals compromised hardware or uncertain installation, replacement with⣠the correct 316112005 kit is warranted to restore designed protection. Following â˘theâ manufacturer’s instructions and âŁusing genuine parts helps ensure compatibility and reliable performance.
Ultimately, the anti-tip bracket is a straightforward⣠but critically â¤important safety device, â˘and preventive maintenance or timely replacement can substantially reduce risk. For owners who are unsure about assessment or installation, consulting â˘a qualified technician provides an added measure of âassurance that the bracket is installed correctly and the oven complies with⣠recommended âŁsafety âŁpractices.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
