8171378RC Whirlpool Dryer 6′ 3-Wire 30 Amp Dryer Power Cord By is a 6-foot, three-conductor supply cord designed to connect a compatible Whirlpoolâ dryerâ to a 120/240 V⤠split-phase household circuit via a three-prong outlet. As a hardwired external power lead it contains two hot conductors and one neutral conductor (no separate equipment ground), is sized for a 30 A branch circuit (typicallyâ 10 AWG copper)and âterminates in the standard threeâterminal configuration used on dryers equipped for threeâwire service.
Within the appliance, this power âcord serves as the primary mains feed to the terminal block and thus supplies the drum motor, heating element, âtimers/controls and any 120 V loads that derive power from the neutral. It interfaces directly â¤with the dryer’s terminal block, internal wiring harness, thermal fuses/limit⣠switches and the control âassembly; in threeâwire⣠installations the neutralâ conductor is often â¤bonded to the dryer chassis, which has implications for grounding and safety. Because it is the main path for line voltage, damage, lose⤠connections or incorrect installation can result in loss of function, intermittent operation, arcing, overheating or nuisance tripping of âŁthe supply circuit.
In this article readers will find a technical overview of the cord’s function⣠and physical characteristics, guidance on⣠model and terminal compatibility, common failure symptoms to watch for,â diagnostic checks a technician⢠would perform (visual inspection, continuity â¤and voltage verification, checking terminal tightness)and practical replacement considerations such⤠as correct ampacity and wire gauge, connector type, cord length, strain relief and the code-driven decision to âuse or convertâ to aâ fourâwire installation. Recommendations emphasize âidentifying electrical faults and selecting the⢠appropriately rated replacement while observing applicable safety â˘procedures and local electrical code requirements.
Table of Contents
- Electrical Function and role of the 3-Wire 30 Amp Dryer Power Cord in Whirlpool Dryers
- How the 8171378RC Whirlpool Dryer 6′ â3-Wire 30 âAmp Dryer Power Cord By Interfaces with the Terminal Block, Line Voltageand Chassis Grounding
- Common Electrical and Mechanical âFailure Symptoms Associated with 3-Wire 30 Amp Dryer Power Cords
- Replacement âConsiderations and step-by-Step Installation âProcedures for 3-Wire 30 Amp Dryer Power Cords in Compatible Whirlpool Models
- Q&A
- To Conclude
Electrical Function and role of the â˘3-Wire â30 Amp Dryer Power Cord in Whirlpool âŁDryers
The 8171378RC Whirlpool âŁDryer 6′ â¤3-Wire 30 Amp Dryer Powerâ Cord⤠By is a replacement service cord designed to deliver the dryer’s line voltage and neutral to the appliance. In a nominal 240 V dryer circuit the cord carries two hotâ legs (each ~120 V to âneutral) that supply the⣠heating element and a combined⢠neutral/equipment-return conductor used by the dryer’s controls and timer. The cord is built to the 30 A rating âŁfor householdâ dryersâ and normally uses 10 âAWG copper conductors; the neutral in a threeâwire installation also⤠provides the chassis return path, so the neutral conductor will carry any imbalance current between the two hot âŁlegs under normal operation.
Compatibility and safe behavior depend on the installation wiring and the dryer model. Many older Whirlpool dryers and existing branch circuits with a threeâprongâ receptacle accept this 3âwire âcord, but current electrical code requires a separate equipment âgrounding conductor for new installations (fourâwire).When replacing or installing the cord,verify the dryer’s terminal block configuration,confirm the supply⣠receptacle type â˘(for example,NEMA 10-30 on legacy âthreeâprong installations),secure the cord lugs under the⣠terminalâ block clamp,and test⢠continuity with the supply disconnected. Converting a dryer from 3âwire to a 4âwire system requires adding a dedicated ground conductor and removing any neutral-to-chassis bond per the⣠manufacturer’s service instructions and local code.
- Key checks: correct receptacle type, 10 AWG conductor size, secure lug attachmentand verification of neutral-to-chassisâ bonding where applicable.
| Item | Description |
|---|---|
| Conductors | Two hot conductors + one combined neutral/equipment-return (3âwire configuration) |
| ampacity / Voltage | Rated 30 A for nominal 240 V dryer circuits |
| Typical wire gauge / Plug | 10 AWGâ copper; legacy 3âprong âNEMA 10â30 receptacle on existing installations |
How the 8171378RC Whirlpool Dryer 6′ 3-Wire 30 Amp Dryer Power Cord By Interfaces âŁwith theâ Terminal âBlock, Line Voltageand Chassis Grounding
The 8171378RC Whirlpool Dryer⣠6′ 3-Wire 30 Amp Dryer âPower âCord By terminates as a simple three-conductor assembly that connects to the dryer’s terminal block: two outer conductors carry the opposing 120 V legs (L1 and L2) that together provide the 240 V heating supplyand the center conductor serves as the neutral return and 120 V reference for timers, lightsand some control circuits. âAt the terminal block the cord’s lugs orâ spadeâ ends fasten under the terminal screws so each hot conductor lands on an outer terminal and the neutral lands on the center terminal.As threeâwire installations do not include a separate equipment grounding conductor,the appliance frame is tied to neutral inside the dryer by a neutral-to-chassis bonding â˘strap; that bonded⤠connection givesâ the chassis a path back to the service â¤neutral but also means the chassis is not isolated âfromâ neutral in âthis configuration.
Technically, the cord is compatible onlyâ with dryers âŁwired or configured for a bonded neutral arrangement; pressing a replacement cord like thisâ onto a dryer designed for a fourâwire configuration requires either installing the correct internal bond or switching to a fourâwire cordâ per code. Practical installation checks include confirming terminal screw sizes and âŁlug fit, verifying continuity between the neutral terminal and the chassis (for threeâwire setups)and ensuring screws are tightened to secure electrical contact. Typical installation checklist andâ reference values most technicians use are â¤shown below to help avoid common mistakes during replacement or troubleshooting.
- Confirm dryer is set up for 3âwire use (bonding strap present) or convert âtoâ 4âwire wiring as required by local âŁcode.
- Power off at the breakerâ before removing or replacing the cord; verify âno voltage â¤with a meter.
- Fit lugs under terminal screws and tighten; check continuity between neutral terminal and chassis for expected bonding in 3âwire⣠systems.
- After installation, test both line-to-line voltage (~240 â¤V) and line-to-neutral voltages (~120 V) at the terminal block before restoring normal âoperation.
| Item | Description |
|---|---|
| L1 / Hot 1 | One outer conductor; supplies one 120 V leg of the 240 V heating circuit. |
| Neutral (center) | Center conductor; provides 120 V reference for controls and is bonded to chassis in 3âwire systems. |
| L2 / Hot 2 | Other outer conductor; supplies the⤠opposingâ 120 V legâ to complete the 240 V circuit. |
Common Electrical and âMechanical Failure âŁSymptoms Associated with 3-Wire â30 Amp Dryer Power Cords
The 8171378RC Whirlpool Dryer 6′ 3-Wire 30 Amp Dryer Power Cord By is a replacement cord that provides two hot⤠conductors and a shared neutral used byâ manyâ dryers with a âthreeâwire⣠terminal block. In this arrangement the âtwo hot legs deliver the element voltage while the neutral supplies the 120 V reference for timers and control circuits; the cord terminates in three insulated conductors sized for 30 Aâ (commonly 10 âŁAWG) with lugsâ or a molded plug that must match⣠the appliance terminalâ configuration. Compatibility depends on âthe dryer’s terminal layout and whether the installation requires a separate grounding conductor (a fourâwire cord) for your outlet; verify conductor gauge, lug typeand strainârelief fit before installation.
Common electrical and â˘mechanical failure symptoms for a 3âwire 30 A dryer cord are generally related â¤to high contact resistance, insulation breakdownor mechanicalâ loosening at the termination. Electrical issues manifest as reduced heater â¤performance or long dry cycles due to voltage drop, repeated circuit trips from shorting or âarcingor intermittent operation from a loose lug; mechanical problems include melted or deformed plug blades, cracked insulationand a compromised strain relief that allows conductor movement and eventualâ fatigue. Technicians should measure continuity and voltage under load-expect nearâzero ohms per conductor, approximately ⣠240 V across the two hots and about 120 V from each hot âto neutral-since âelevated resistance or meaningful voltage drop under load pinpoints a failing cord orâ poor terminal connection.
- Intermittent powerâ or cycling during operation (loose lug or broken conductor).
- Low⤠or no heat while⢠motor runs (high resistance/voltage drop across hot legs).
- Visible overheating: discolored/melted insulation, scorched terminal blockor burn smell (arcing or poor contact).
- Sparking at âŁthe plug or terminal and repeated breaker trips (shorting or arcing).
- Physical damage: frayed conductors, bent/missing plug bladesor failed strain relief (mechanical stress).
| Item | Description |
|---|---|
| Voltage under load | Measure ~240 V across hots; significant drop indicates highâ resistance in cord or termination. |
| Continuity / resistance | Expect very low ohms; >0.5-1 Ί suggests a âdegraded conductor or poor lug contact. |
| Visual signs | Discoloration, melted insulationor burn marks point to localizedâ heating and imminent failure. |
Replacement Considerations and Step-by-Step Installation Procedures for 3-Wire 30 Amp dryer Power Cords in Compatible Whirlpool Models
The 8171378RC Whirlpool Dryer 6′ 3-Wire 30 Amp Dryer Power Cord â¤By isâ a â6-foot, three-conductor replacement cord ratedâ for 30 amps and intended âfor Whirlpool dryers with⤠a three-terminal block configuration. âFunctionally, the cord provides two hot legs and a neutral conductor – â˘delivering approximately 240 V across the hot terminals and 120 V between either hot and the neutral.Conductors for a 30 A â˘dryer circuit are typically copper and sized toâ 10 AWG; the neutral in a 3-wire â˘installation also serves⣠the grounding function for the chassis on older appliances. Use of this cord is limited to dryers originally configured for a 3-prong connection; dryers designed for a 4-prong cord âor upgraded to a dedicated equipment ground require a different cord and grounding arrangement to meet âŁcurrent electrical code.
Before replacing the cord, verify the dryer’s terminal block configuration, the⣠branch-circuit breaker ratingand the outlet type; inspect the terminal âŁblock for corrosion or damaged studs and replace any worn⢠hardware. For⣠installation: disconnect â˘power at the breaker and confirm absence of voltage, remove⤠the rear access panel, route the⢠cord through the existing strain relief, terminate the two hot conductors to the outer block terminals (L1 and L2) â˘and the neutral to the center terminal, tighten the terminal screws to a firm mechanical connection âper the appliance specification, secure the âstrain relief â˘and panel, then restore power and âverify voltages under no-load and with a dryer cycle. Comply with local electrical codes – many jurisdictions now require a 4-wire connection for new installations,⣠and converting between 3- and 4-wire configurations may require additional parts or â˘a licensed electrician.
- Disconnect breaker and verify zero voltage with a meter.
- Remove access panel and existing cord; inspect â˘terminal block and mounting hardware.
- Install strain relief,route new cord,and attach âŁhot conductors to outer terminals and neutral to center.
- secure terminals and strain relief, replace panel, restore powerand measure L1-L2 (~240 V), L1-N and L2-N â(~120 V).
- Confirm dryer runs correctly and there is no âŁoverheating at the âterminal block; consult an electrician if any irregularities appear.
| Item | Description |
|---|---|
| Conductor size | Typically 10 AWG copper for 30 A dryer circuits |
| Amp rating | 30 amps |
| Cordâ length | 6 feet |
| Compatibility | Dryers â¤with a 3-terminal block⣠(L1, L2, neutral/ground).Not for dryers requiring a 4-prong/4-wire âconnection unless local code permits. |
Q&A
What â¤exactly is the 8171378RC Whirlpool 6′ 3âWire 30 Amp dryer âŁpower âcord and what dryers⤠is it meant for?
The 8171378RC is a 6âfoot, threeâconductor power⤠cord⤠rated for 30 amps and intended for 240âvolt electric clothes dryers that use a 3âterminal⤠block and a 3âprong inlet. It’s an â¤OEMâstyle replacement cord commonly used on older Whirlpool (and⢠some compatible) dryer models âthat where originally âwired with a 3âprong connection. Always confirm â¤the part number compatibility for your specific model before purchasing.
What wire size and âŁelectrical rating does this cord use?
This cord is⤠intended⤠for a 30 amp dryerâ circuit and is typically constructed with 10 AWG âŁcopper conductors (one neutral âŁand two hot conductors). â¤It is rated for 240 volts at 30 A, which is the standard residential dryer circuit â˘rating.Do not use â˘it on circuits with⣠lower â˘ampacity or with undersized wiring.
Can I plug this 3âprong cord into a modern 4âprong outlet (or use an adapter)?
Noâ – a 3âprong cord will not properly âconnect to a 4âprong outlet without⢠an adapter. While adapters exist, current electrical code (NEC since 1996) requires new âdryer installations to use⣠a 4âwire (separate ground)⤠connection. if your home has a 4âprongâ outlet, the correct solution is to replace the dryer’s cord with a 4âwire cordâ and properly attach theâ separate equipment ground to the dryer chassisor have an electrician change the outlet if appropriate.
How do I safely replace the dryer cord with the 8171378RC?
Basic replacement steps: 1) Turn off and lock out the dryer circuit at the breaker panel and verify power is off. 2) Pull the dryerâ away and remove the terminal block cover.3) Note the existing wire positions (centerâ is neutral, âtwo outer are â˘hot). 4) Remove the â¤old cord and âŁfeed the new cord through the strainâ relief. 5) Attach⢠the ânew cord conductors to the same terminals (center = neutral, outer = hots), tighten terminalâ screws firmlyand reinstall the strain relief. 6) If replacing likeâforâlike on a 3âwire installation, ensure the neutral is bonded to the chassis per the dryer’s original configuration. 7) Replace the cover,restore power,and test. If you’re notâ comfortable or local code â˘requires, hire a âqualified electrician or technician.
Howâ do I convert âmy dryer from a 3âwire to a 4âwire connection?
To convert to a 4âwire (codeâcompliant) hookup: purchase a 4âwire (4âprong) dryer cord, remove the âneutral-to-chassis bonding strap or⣠jumper (this separates neutral and ground), attach the neutral conductor to theâ center terminal,⣠attach theâ two hots to the outer terminalsand attach the newâ ground (green) conductor to the dryer’s ground screw on the chassis.Always follow the dryer manufacturer’s â¤instructions and local electrical code; if unsure, hire a licensed electrician.
Is it safe to use an⤠extension cord or cut/extend the 8171378RC cord?
No. Do not use an extension cord with an⤠electric dryer – âdryer load currents (30 A) and heat make extension cords âunsafe. Also do not cut âor splice theâ dryer cord in the field. â¤If the cord is to short,⤠obtain a longer certified replacement cord or have a licensed electrician provide a permanent wiring âsolution that meets code.
Howâ can I tell if the cord âis installed or working âincorrectly after replacement?
Signs of improper installation include warm orâ melted insulation at the cord or terminal block,a burning smell,frequent tripping of the 30 Aâ breaker,intermittent power,or the dryer notâ heating. These symptoms may indicate loose terminal screws, wrong wiring, damaged cordor wrong circuit sizing. If you see any of these, promptly âshut off power and inspect connections or call a qualified technician-loose or highâresistance connections are fire hazards.
Is âŁthis an OEM/ULâlisted part and are there code considerations I should know?
The 8171378RC is an OEM replacement style cord âdesigned toâ meet manufacturer specifications for dryers using a â3âprong inlet. Many OEM cords are ULâlisted orâ or else safetyâcertified, âbut⤠you should verify âthe listing on the product packaging or â˘label. âŁNote⣠that electrical code⤠requires new dryer installations to use aâ 4âwire connection (separate equipment ground). Even when replacing a â¤cord on an existing 3âwire installation, check local code requirements-someâ jurisdictions â¤require upgrading to a 4âwire system.
To Conclude
The 8171378RC Whirlpool Dryer 6′ 3-Wire 30 Amp dryer power cord serves a fundamental role in providing âa safe, properly rated electrical connection between the dryer and âhousehold supply. Its 3âwire configuration, 30âamp rating and 6âfoot length are designed to match the electrical requirements and physical setup of compatible Whirlpool models, helping ensure consistent⤠performance and reduce the risk of overheating or poor connections⤠when installed correctly.
Accurate âdiagnosis is essential when power issues or visible wear are present. Signs such as discoloration, melting, sparking, intermittent poweror a tripped breaker can â¤indicate cord or connection problems; identifying the âŁroot cause-whether cord degradation, terminal â˘damageor a separate electrical fault-helps â˘prevent unnecessary âreplacements and addresses safety concerns promptly. Because electrical testing and repairs carry inherent risks, âassessment by a qualified technician is recommended if there is any uncertainty.
When replacement is necessary, selecting a cord with the correct part number and electrical âŁrating and ensuring proper installation and adherence to local codes will preserve dryer function and reduce safety risks. Timely, appropriate diagnosis followed by the correct replacement or professional repair â¤protects the appliance’s longevity and contributes to overall household electrical safety.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
