WB44K5013 GE Oven Range Bake Element is the factory-designated bake heating element used in many GE electric ovens and ranges. It is a resistive, metal-sheathed tubular heating element designed to convert line-voltage electrical energy into radiant and convective heat within the oven cavity. Constructed to be mounted inside the oven enclosure, the element is insulated and terminated for connection to the appliance wiring harness or terminal block and is intended to withstand repeated thermal cycling and exposure to oven atmospheres.
Inside the appliance, the bake element is the primary heat source for baking operations and interacts directly with the oven control system, temperature sensing device (thermostat or thermistor), relays or infinite switchesand the wiring and protective fuses or thermal cutouts. When the control calls for heat it supplies voltage to the element; the sensor monitors cavity temperature and the control modulates power to maintain setpoint. The element’s electrical and thermal behavior therefore affects temperature rise,uniformity,and energy draw,and faults in the element can present as open circuits,ground faults,or altered heating characteristics that may also affect or be affected by the control and sensor circuits.
In this article readers will find a technical overview of the bake element’s function and construction, guidance on checking model compatibility and correct replacement part selection, common failure symptoms to recognizeand a structured approach to troubleshooting including safe isolation and basic electrical checks. The article will also cover practical replacement considerations-terminal and mounting verification, insulation and seal condition, and post-replacement verification-and note related components to inspect if symptoms persist, such as the temperature sensor, control board outputs, and wiring harness integrity.
Table of Contents
- Function and Role of the Bake Element within the Oven’s Heating System
- How the WB44K5013 GE Oven Range Bake Element Works Inside the Appliance
- Common Failure Symptoms and Diagnostic Indicators for Bake Element Issues
- Replacement Considerations and Installation Procedure for the WB44K5013 Bake Element
- Q&A
- To Wrap It Up
Function and Role of the Bake Element within the Oven’s Heating System
The WB44K5013 GE oven Range Bake Element is a resistive heating element mounted beneath the oven cavity that provides the primary,sustained thermal input for baking cycles. When supplied with line voltage it converts electrical energy into radiant and convective heat; the oven control board or mechanical thermostat modulates that input by switching the element on and off to maintain set temperature. Its physical placement and surface area are chosen to produce an even ambient oven temperature rather than the intense, localized heat used for broiling, so proper fit and electrical rating are critical for preserving the oven’s temperature calibration and control algorithm behavior.
Technically, the element behaves as a simple resistive load whose continuity and nominal resistance determine proper operation; common service checks include a visual inspection for breaks or blistering and an ohm measurement to confirm continuity and approximate resistance. Compatibility requires matching the element’s voltage/wattage rating, terminal typeand mounting flange to the oven model; using an element with incorrect wattage can produce slow heat-up, extended on/off cyclingor inaccurate temperature readings by the control system. Practical examples: a completely open reading on a multimeter indicates a failed element that will produce no heat, while a partially corroded terminal or a warped element can cause intermittent heating and uneven bake results. Follow safe service practice-isolate power, verify continuity, and compare readings to manufacturer specifications before replacement.
- Common symptoms of element issues: no heat, uneven baking, visible breaks or blisteringand open-circuit on an ohm meter.
- Service checks: power isolation, visual inspection, continuity test, and verifying terminal integrity and mounting fit.
- Compatibility checklist: matching voltage/wattage, terminal type (Faston), flange/mounting dimensionsand part number correspondence to oven model.
| Item | Description |
|---|---|
| Part | WB44K5013 GE Oven Range Bake Element |
| Typical operating voltage | 208-240 V (line supply dependent) |
| Typical wattage | Approximately 2,000-3,000 W (model dependent) |
| Typical DC resistance (room temp) | Approximately 20-30 Ω for a ~2,400 W element at 240 V |
| Mounting/terminals | Flanged mounting with insulated swift-disconnect terminals (Faston) |
How the WB44K5013 GE Oven range bake Element works Inside the Appliance
WB44K5013 GE Oven Range Bake Element is the resistive heating element mounted at the bottom of the oven cavity and is responsible for generating the radiant heat used during bake cycles. The element consists of a resistance alloy conductor formed into a coil and enclosed in a formed metal sheath; when the oven control or relay applies line voltage the conductor heats and the sheath radiates heat into the cavity while also transferring heat to air currents. In normal operation the control cycles the element on and off to maintain set temperature; electrical failure modes include an open circuit (no continuity), localized burn‑throughsor shorting to chassis ground, and mechanical issues include bent mounting brackets or damaged terminals that prevent secure electrical connection.
Compatibility and practical servicing require matching electrical and mechanical specifications: terminal type and spacing, flange/mounting hole patternand the element’s voltage/wattage rating must correspond to the appliance design. Technicians typically confirm a failed WB44K5013 by measuring continuity with power disconnected, verifying correct supply voltage at the connector under load conditionsand visually inspecting for breaks or hot spots before replacement. Practical examples: installing an element with incorrect terminal spacing can prevent proper seating and lead to intermittent contact and arcing; using an element with higher wattage than the range design can shorten component life or stress the control board.
- Common symptoms: no heat, slow heat recovery, uneven baking, visible breaks or blistering.
- Electrical checks: continuity test (open = replace); check for shorts to chassis ground.
- Compatibility checklist: confirm terminal type, terminal spacing, overall lengthand wattage/voltage rating.
- Operational behavior: cycles with thermostat/relay and may glow at elevated temperatures.
| Item | Description |
|---|---|
| Function | Resistive heater that provides the primary radiant heat for bake cycles. |
| Connections | Two line terminals (verify spade or screw type and spacing before replacement). |
| Failure mode | Open circuit, sheath damage/hot spotsor short to ground; causes loss or reduction of heat. |
Common Failure Symptoms and Diagnostic Indicators for Bake Element Issues
The WB44K5013 GE Oven range Bake Element is a resistive heating element that converts electrical energy into radiant heat for baking applications. It mounts at the bottom of the oven cavity and must match the range’s voltage, wattage rating, and terminal configuration to operate correctly; mismatched parts can produce incorrect temperatures or overload controls. A properly functioning bake element shows uniform surface discoloration when heated, a stable low-resistance path between its two terminalsand no electrical continuity to the oven chassis. Common failure mechanisms include open-circuit breaks from thermal cycling, localized high-resistance spots caused by internal filament degradation, and insulation breakdown to ground due to corrosion or physical damage.
- No heat or significantly reduced bake performance while other functions (e.g., broil or convection) appear normal.
- element remains cold or does not glow at operating temperature; visible breaks, blistering, or flaking of the sheath.
- intermittent heating that correlates with temperature cycles-indicative of hairline filament cracks.
- Tripped breakers,blown fuses,or oven controls that shut down immediately-possible short to ground.
- Multimeter readings: open circuit (infinite resistance) across terminals indicates a broken element; measurable resistance across terminals but low resistance to chassis indicates a ground fault.
Practical diagnostics start with removing power and disconnecting the element, then measuring across the two terminals with a digital ohmmeter. Typical bake elements for household ranges present roughly 15-40 Ω at room temperature depending on wattage; values significantly above this range can indicate partial failure, while infinite resistance denotes an open element. Also measure resistance from each terminal to the oven chassis-any low reading (near zero) indicates insulation failure and replacement. If electrical tests are within expected ranges but symptoms persist, inspect terminal connections, control relaysand oven sensors because loose connectors or faulty control circuits can mimic element faults; replace the WB44K5013 only with a part that matches the original electrical rating and mounting to ensure compatibility.
| Item | Description |
|---|---|
| Typical resistance | Approximately 15-40 Ω at room temperature (varies with element wattage) |
| Continuity check | Low resistance across terminals = intact element; OL/infinite = open circuit (replace) |
replacement Considerations and Installation Procedure for the WB44K5013 Bake Element
The WB44K5013 GE Oven Range Bake Element functions as the primary resistive heating element located at the bottom of the oven cavity; it converts electrical energy into radiant and conductive heat to maintain set bake temperatures. Typical failure modes include open circuits from broken internal coils, short circuits to the element sheath causing tripping of protective devicesand localized hot spots from physical deformation or coating breakdown. When evaluating compatibility, confirm that replacement elements match the oven’s supply voltage, terminal styleand mounting dimensions; the WB44K5013 GE oven Range Bake element will only perform correctly if the terminal spacing and bracket orientation align with the range’s existing connectors and mounting flange.
Replacement and installation require basic electrical diagnostics and mechanical alignment. Before removing the old element, Disconnect power at the breaker and verify absence of voltage with a meter; then check element continuity and insulation to chassis (no continuity to ground). When installing,ensure spade terminals are fully seated and that the element bracket aligns flush with the oven cavity to avoid arcing or uneven heating. After assembly, run a low-temperature verification cycle and observe heating uniformity and control response; if temperature output is irregular, re-check electrical connections, thermostat/relay operation, and element resistance. practical checklist and reference values are below to assist technicians during assessment and installation.
- Pre-replacement checks: power off, continuity test, insulation-to-ground test.
- Mechanical: verify terminal type (spade) and mounting bracket alignment before tightening.
- Post-installation: low-temp verification run, inspect for even glow and proper control cycling.
| Item | Description |
|---|---|
| Operating voltage | 240 V nominal (confirm against appliance data plate) |
| Typical DC resistance | Approximately 20-40 Ω depending on wattage; measure with a multimeter |
| Mounting/terminals | Rear flanged bracket with insulated spade terminals; confirm connector fitment |
Q&A
What is the WB44K5013 bake element?
The WB44K5013 is a genuine GE replacement bake (lower) heating element for certain GE/Hotpoint electric ovens and ranges.It is indeed the heating element that provides the bulk of the oven’s baking heat, mounted on the bottom of the oven cavity and connected to the oven’s 240 V supply.
What are common symptoms that the WB44K5013 bake element is failing?
Common signs of a failing bake element include: oven not heating or taking much longer to reach temperature, uneven baking or hot spots, visible damage such as blistering, cracks, or breaks in the element tube, arcing/sparking inside the ovenor tripping the breaker when the oven is switched on.
How do I test the WB44K5013 bake element with a multimeter?
First disconnect power at the breaker. Remove the oven racks and the element mounting screws, pull the element forward enough to access the two terminals (you can test in place if safe and power is off). Set your multimeter to the ohms (Ω) range and measure across the two element terminals. A good element will show a low resistance (not infinite)-typically in the low tens of ohms (common values around 15-30 Ω depending on the element wattage; e.g., ~20 Ω for a ~3000 W element at 240 V). If you read infinite resistance (open circuit), the element is broken and must be replaced. Also check each terminal to the metal element body; there shoudl be no continuity (no short to ground).
How do I safely replace the WB44K5013 bake element?
Turn off power at the breaker (do not rely on the range’s controls). Remove oven racks and locate the two screws holding the element at the rear of the oven cavity. Remove the screws and carefully pull the element forward. Disconnect the two quick-disconnect terminals (note their orientation). Install the new element by reconnecting terminals, pushing the element into placeand fastening the mounting screws. Replace racks and restore power. Typical tools: screwdriver or nut driver and needle-nose pliers. Expect 15-30 minutes for a simple replacement. Wear gloves and avoid touching exposed wiring; if you are not cozy with electrical work, hire a qualified technician.
How do I know this part is compatible with my oven model?
Check your oven’s model number (usually on a tag around the door frame or behind the broiler drawer) and verify compatibility against the part number reference from GE or the parts supplier. The WB44K5013 is listed for many GE/Hotpoint models, but always confirm compatibility by cross-referencing the oven model or the original part number. If in doubt, provide your full model number to the parts supplier or technician.
What causes bake elements like the WB44K5013 to fail?
Typical causes include normal thermal cycling and age (metal fatigue), food spills or moisture causing corrosion/shorting, physical damage (dents or punctures), and occasional manufacturing defects. Heavy grease or acidic spills left on the element can accelerate deterioration. Electrical faults elsewhere (control board or stuck relays) can also stress the element but do not usually cause an immediate element failure.
Can I clean a dirty WB44K5013 element or do I need to replace it?
If the element is only dirty (burnt-on food, grease) and shows no physical damage or electrical faults, you can clean it gently with a non-abrasive cleaner and a soft cloth once it is cool and power is off. Do not use steel wool or metal scrapers that could damage the protective outer sheath. If you see blistering, holes, breaks, or the element fails an electrical continuity test, it should be replaced.
I replaced the bake element but the oven still doesn’t heat-what should I check next?
If a new element shows correct resistance and is installed properly but the oven still doesn’t heat, check: (1) that the element receives voltage (test at the terminals with power on and extreme caution or have a technician test), (2) the oven control board or the bake relay/selector switch (may not be sending power), (3) door switches or thermal fuses/thermostats/internal sensors, and (4) household circuit/breaker and wiring. If unsure, call a qualified appliance technician to safely diagnose control or electrical issues.
To Wrap It Up
the WB44K5013 GE Oven Range Bake Element serves as the primary heating component responsible for producing consistent, evenly distributed heat in the oven cavity. Its proper function directly affects cooking performance, temperature accuracy and overall appliance efficiency; a compromised or failing bake element can cause uneven baking, extended cook times and potential safety concerns. As an OEM-specific component,the WB44K5013 is designed to meet the original equipment specifications for fit and heat output,making it a key part in preserving the intended operation of compatible GE ranges.
Timely and accurate diagnosis of bake element issues-through visual inspection and appropriate electrical testing-helps determine whether repair or replacement is necessary and avoids unneeded service costs. When replacement is required, using the correct WB44K5013 part and following manufacturer guidelines or engaging a qualified service technician will restore reliable performance, maintain safetyand extend the useful life of the range. Proper diagnosis and replacement ensure the oven returns to expected heating characteristics and safe operation.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
