316031501 Frigidaire Oven Valve âŁis a gas flow control valve assembly used inâ frigidaire gas ovens and âranges. it is an electromechanical â¤component that meters and âŁinterrupts gas flow too âthe oven burners; typical assemblies âinclude one or moreâ solenoid-actuated valve elements, a pressure-resistant âhousing, inlet⢠and outlet⣠ports âŁfor⢠the manifoldand an âŁelectrical connector for controlâ signals. â˘As a discrete service part, the⢠316031501 âis specified to match theâ dimensional, pressureandâ electrical characteristicsâ required⤠by the⤠original appliance design.
Inside the appliance, the valve sits betweenâ the household gas âsupply (and â¤pressure regulator) and the bake/broil burners or manifold andâ directly interfaces with the ignitionâ and control systems. âIt responds to âsignals âfrom⣠the oven control board,â thermostat âor oven sensor â˘and works in concert⢠with the⤠igniter or⣠pilot⢠system and⣠any⢠safety interlocks (thermocouple, flame-sensing circuit) toâ permit or âstop gas â¤flow.â Proper operation of â¤this â¤valve is criticalâ to controlled â˘ignition, stable⤠burner operationand prevention âof⢠unintended gas leakage; âtypical mounting⢠is â˘at the rear or undersideâ of the oven ânear the burner manifold, withâ both gas line fittings âand an electrical âharness connection.
This articleâ will â˘describe the 316031501 â˘valve’sâ function and typical internal features,outline compatibility considerationsâ and how to confirm the correct replacement part for a⤠given Frigidaire⣠model,identify common failure symptoms (such as,no heat,delayed âignition,continuous gas flow,or gas â˘odor),and present practical troubleshooting checks technicians⢠can perform (electrical coil resistance and voltage checks,interaction testing âwith the igniter and control board,and pressure/leak tests). âIt â¤will also âcover â˘replacement considerations and safe work practices: âisolating gasâ and electrical supply, proper âgasketâ and torque practices,⣠post-installationâ leak and operational testingand brief notes on âdiagnostic⢠tools and measurements âuseful duringâ service.
Table of Contents
- Function and role âof the Oven Gas⤠Valve in Ignition, Flow Regulationand â¤Safety Interlocks
- How the â¤316031501 Frigidaire Oven Valve Works Inside the Appliance
- Common Failure â¤Symptoms and Measurableâ diagnostic Indicators of Valve Degradation
- Compatibility, Replacement Considerationsand⣠Installation Procedures âŁfor Oven Valve âŁAssemblies
- Q&A
- In Conclusion
Function andâ Role of the âŁOven Gas Valve in â˘Ignition, Flow Regulationandâ safety Interlocks
The âŁ316031501 Frigidaireâ Oven Valve is a solenoid-actuated safety valve used in gas oven assemblies â¤to control⣠ignition âsequencing, modulate âŁgas flow âto the⣠burner manifoldandâ provide mechanical interruption âŁfor safety⢠interlocks. When the â˘oven control or safety⤠circuitry calls for⣠heat, theâ control module applies the correct control⣠voltage âto the valve⣠coil, overcoming the spring-loaded seat⣠and permitting gas to âŁflow toâ the igniter area; the valve remains closed⤠until the⢠controller energizes the coil â˘and the ignition âsystemâ confirms a flame. Replacement or â¤retrofit requires â˘matching the valve’sâ actuation voltage, port size, manifoldâ mounting patternand pressure ârating to theâ appliance-verify compatibility â¤against the oven model and service documentation to avoid weak flames, âleaksor control conflicts.
The valve â˘also functions as the primary â˘safety device when ignitionâ fails: flame⣠sensors âor thermocouples⢠inform the control board,⣠which de-energizes the valve âcoil and returns âthe valve to the closed position⢠if a flame isâ not established.⣠Common failure modes include coil burnout, a sticking plunger â˘or degraded seal that results in slowâ leaksand âinternal leakage that⤠prevents reliable shutoff; these produceâ diagnostic symptoms âsuch as clicking without ignition, continuous gas⤠odoror intermittent⢠lighting. Technicians typically diagnose the assembly by measuring coil continuity and⢠control âŁvoltage, verifying manifold â¤pressure and seat integrityand confirming that the flame-sensing circuit permits âvalve opening only â˘after â¤aâ valid â˘flame signal.
- Primary functions: âŁignition enable, gas flow control, safety shutoff.
- Common âsymptoms of âfailure: âŁno â˘gas flow, gas smell⣠with no flame,⢠intermittent ignition.
- Diagnostic checks: coil resistance, applied⢠control voltage, manifold⣠pressure, flame-sensor response.
| item | Description |
|---|---|
| Valve type | Normally-closed solenoid âsafety âvalve âŁforâ oven manifold |
| Control âinterface | Operated by oven control/ignition circuit; matchâ voltage⢠and âconnector type |
| Failure indicators | Clicking, â¤persistent gasâ flow, inabilityâ to lightor intermittent operation |
| Replacement consideration | Match part ânumber, mounting, âport size,â and pressure rating; consult service manual |
Howâ the 316031501 Frigidaire Oven âValve Works Insideâ the â˘appliance
The 316031501⤠Frigidaire Oven Valve is an âelectrically actuated⣠gas safety valve that meters⤠and interrupts fuel â¤supply to the bake⢠and/or broil âburners. inside theâ appliance it functionsâ as a normally-closed device âthat receives a command from the oven control and the ignition sequence (igniter or sparkâ module); when the â¤control energizes the âvalve coil theâ valve opens⤠to allow gas flow and the igniter lights â¤the burner.â Some valve assemblies âare strictly on/off while â˘others⣠in âŁcertain models âcan modulate flow slightly to support âtemperature control; regardless⤠of âtype, reliable operation âdepends on correctâ mounting to the âmanifold, matching⢠port geometry, â¤and⤠compatible electrical connectors and controlâ signals used âby the Frigidaire chassis.
In practical service termsâ the âŁvalve behaves âŁpredictably: a stuck-closed valve results â¤in noâ heat, â¤a valve âthat fails to seal can allow slow leaks or delayed ignitionand intermittent coil or â˘connector âfaults âproduce cycling or loss of flame. â˘Technicians typically inspect valve coil continuity, verify the oven control is providing⣠the expected actuation signaland âconfirm theâ igniter is drawing sufficient current to permit⢠normal valve âtiming. For field replacement âmatch â˘the⣠316031501 valve’s â˘mounting, manifold interface and âŁwiring harness⤠toâ the appliance model;â tighten fittings and use correct gasketing to prevent leaksand⤠verify operation with a controlled ignition test or leak âcheck after reassembly.
- Primary function: safety shutoff and controlled gas delivery to burners
- Common symptoms of failure: no heat, delayed â¤ignition, âŁgas⤠odororâ intermittent âŁoperation
- Compatibility â˘factors: manifold port size, mounting flange, electricalâ connector âtype
| Item | Description |
|---|---|
| Type | Electrically âactuated âgas safety valve (normally â˘closed) |
| Behavior | Opens on âŁcontrol signal; â¤seals toâ prevent gas flow when âŁde-energized |
| Service checks | Coil continuity, controlâ output verification, igniter current and leak âtest |
Common Failure⣠Symptomsâ and Measurable Diagnostic Indicators of Valve Degradation
Theâ 316031501 Frigidaire Oven Valve is theâ gas control element âŁthat meters and isolates fuel to the oven burner. Mechanically it contains â˘aâ sealing âseat, stem/poppet and⣠an actuating solenoid âor thermalâ mechanism depending on the âŁmodel; electrically it presents⢠a âcoil⣠whoseâ continuity âŁand response canâ beâ checked with a multimeter. Compatibility considerations âŁinclude the valve’s mounting âfootprint, inlet/outlet port sizes and electrical âconnector type – theseâ must match the appliance manifold⤠and⤠control wiring â¤for reliable operation.â Technicians evaluate valve behavior by observing⤠whether the valve fully⣠seals when de-energized, opens promptly when âcommandedand holds steady under manifold pressure âwithout weeping or intermittent flow.
- Continuous gas flow or smell of â¤gasâ with burner off (seat leakage)
- Repeated ignition clicks or delayed ignition after command⤠(slow response or weak actuation)
- Weak, âŁyellow or unstable flame during â˘operation (restricted or partial opening)
- Oven fails to reach set temperatureâ or cycles excessively (inaccurate metering)
- Audible â˘hissing from the valve body under⣠pressureâ (internal âor external leak)
Measurableâ diagnostic indicatorsâ include valve⢠coil resistance and continuity, time-to-open under rated voltage,â pressure decay or leak-rate tests at the inlet/manifoldâ connection,â and steady-state⢠manifold pressure under load. Practical⤠checks: â˘measure coil resistanceâ and compare with the appliance âservice spec, apply controlled voltageâ and time the mechanical response, â¤perform a bubble or pressure-decay test on the isolatedâ valve⤠to⤠quantify leakage, âand confirm manifold pressure with âaâ manometer while the⤠valve is operating. Documenting these readings and comparing them to theâ manufacturer’s service data helps determine whether replacement⤠with a matching â˘316031501 âpart or further⢠system repairsâ are required; always isolate gasâ and follow safe⢠test procedures â¤during⤠diagnosis.
| Item | Description |
|---|---|
| Coil Resistance | Continuity check to detect open/shorted solenoid â˘or degraded windings |
| Seat Leak Rate | Pressure-decay orâ bubble test to quantify leakage pastâ theâ valve âŁseat |
| Response Time | Measured interval⤠from electrical command to âfull â˘valve travel (affectsâ ignition timing) |
| Manifold⤠Pressure | Verification of correct supply pressureâ while â¤valve is open â˘under⣠load |
Compatibility, Replacement âConsiderationsand Installation Procedures for Oven âValve Assemblies
The â316031501 frigidaire Oven Valve is a gas control component that meters and âŁdirects fuel⤠to⣠the bake âand broil âburners via⣠solenoid-actuated or â¤thermostatic ports. In normal operation the âŁvalve⣠provides a pressure-sealed seat that opens to a defined âflow area when energized âor commanded by the oven â˘control board; variations â˘in seat wear,⣠diaphragm leakageor âŁsolenoid coil resistance change flow behavior and can produce low flame, delayed ignitionor continuous âŁgas flow. Compatibility dependsâ on⤠manifold spacing,mounting flange geometry,electrical connector pinout,and fuel type (natural gas vs. LP); while the 316031501 is specified for certain Frigidaire models,⣠cross-referencing model-specific⣠service â¤sheets and⣠part numbers is necessary before substitution because orifice âsizes and internal pressure regulators are often specific⢠to the appliance and fuel⤠type.
Replacement âŁand installation require âcontrolled isolation of fuel and electrical sources, careful handling of sealing surfacesand verification of operation under working pressure. Typical practical steps include shutting off gasâ and power, removingâ the⢠manifold-to-valve nuts with⢠the correct torque to avoidâ damaging threads, replacingâ gaskets and⣠retaining hardware,⢠and âŁrestoring service with⢠a⤠manometer or calibratedâ gauge to⤠confirm outlet pressure and a soap or âelectronicâ leak test at all joints; if converting fuel type, â˘change the orifice⢠and â˘adjustâ regulator settings per the⤠manufacturer’s conversionâ instructions. For âexample,⢠swapping a valve into a âdifferent range series may require a âharness â˘adapter or reorientation of theâ valve body so the âprobe and⤠pilot ports align; â˘aftermarket â¤valves can function but must matchâ electrical ratings and sealing surfaces to avoidâ unsafe âoperation.
- Pre-replacement checks: confirm part number, fuel type, manifold spacingand connector pinout.
- Installation checklist: gas/electrical â˘isolation, replace gaskets, torque â˘fittings, âpressure verification, leak⣠test, âfunctional ignition⢠test.
- Post-installation: âobserve flame pattern,⤠cycling⢠behaviorand control responsiveness â˘under âbake/broil modes.
| Item | Description |
|---|---|
| Part Number | 316031501 – OEM Frigidaireâ ovenâ valve; verify⢠against appliance model listâ before ordering |
| Fuel Type | natural âŁgas or LP⤠– orifice/regulator differences require verification â˘orâ conversion |
| Mounting | Manifold bolt spacing and flange orientation âmust match to avoid adapter fabrication |
| Electrical | Solenoid⣠coil voltage and connector â˘pinout must âmatch control board specifications |
| Verification | Use manometer⣠for pressure checkâ and soap/electronic detectorâ for leak testing after installation |
Q&A
Whatâ is⣠Frigidaire part 316031501 and what does itâ do?
Part 316031501 is the âoven gas valve assembly usedâ onâ certain Frigidaire/Frigidaire Gallery ranges. It⢠controls the flow of âgas to âthe oven burner(s) and acts as⤠a âsafety shutoffâ that is commanded by the⢠oven thermostat or electronic control/igniterâ circuit. Whenâ the control â¤calls⤠for heat the valve opens to allow gas; whenâ the call ends it âcloses to stop gas flow.
What are the common âsymptoms of âŁa failing 316031501 oven âŁvalve?
Common â˘signs â¤include: âŁthe oven not heating at âall while other âŁfunctions work,gas smell⣠but no burner ignition,burners that ignite but will not stay lit,intermittent oven⣠heating,or a clicking/ buzzing valveâ but âŁno gas flow. Because⢠ignition âsystems and igniters often fail first,confirm the igniter â˘and ignition control before replacing â˘the valve.
Can I testâ the âvalve myself â¤to confirm it’s⣠bad?
Basic, âŁnon-invasive checks you can do: verify the control is calling for heat (electronic control⣠signals â¤or knob âŁposition), listen for âthe valve operatingand perform â¤a⣠visual inspection⤠for damage or⤠corrosion. With power off you âcan check the valve’s solenoid coils⢠forâ continuityâ with a âŁmultimeter-an open â˘coil indicates failure. â˘A more âdefinitive test requires⣠measuring the voltage âapplied to the â¤valve â¤when the oven calls forâ heat and/or performingâ a gas â¤pressure/flow test;⣠those should be done by a qualified technician. Always shut off gas and electricalâ power before doing âŁany internal checks.
is 316031501⢠a direct âdropâinâ replacement for my Frigidaire model?
Not necessarily. Frigidaire uses different valve assemblies across models âand model years. Always⤠confirm compatibility by â˘checking your appliance model number against the OEM parts lookup or the part listing. Check physical fit (mounting holes, inlet/outletâ orientation), connector â¤typeand âgas connection type (flare vs. NPT) before purchasing. If â˘in⤠doubt, consultâ Frigidaire parts support or a certified technician.
How arduous is replacing the oven valve and can I do it myself?
Replacement is a â˘moderate-to-advanced DIY task. It involves â˘shutting off and disconnecting⣠the gas âsupply,â turning off electrical power,⣠removing âoven access panels, disconnectingâ wiring and â˘gas fittings, installing the new valveand performing a⤠gas-leakâ test.â Because mistakes⣠can cause⢠gas leaks â¤and â¤fire⤠hazards, manufacturers and safety codes reccommend a qualified service technician perform the â¤replacement unless you⣠are⤠experiencedâ with gas appliance repairs.
What tools and materials are typically needed to⢠replace this valve?
Typical items: â¤basicâ hand tools (screwdrivers, nut drivers), an âŁadjustable wrench or flare-nut⤠wrench⤠for gas fittings, multimeter for âŁelectrical checks, appropriate âgas-rated âŁpipe compound for threaded (NPT) connections (do not use pipe dopeâ onâ flare fittings), new flare nuts or âgaskets⢠if requiredand a gas-leak detector or soapy water for⤠leak testing.⣠Personal protective âequipment and knowlege of â˘appliance grounding andâ isolation⣠are alsoâ required.
How âmuch does âthe 316031501⢠valve cost and are⢠aftermarket⢠parts acceptable?
Price forâ the valve âaloneâ typically ranges from about $100 to $350 depending â˘onâ supplier and whetherâ it’s âŁOEM or aftermarket. aftermarket valves exist, but⣠OEM parts are⤠recommended to ensure correct fit, gas safety⢠certificationand compatibility. If you âŁchoose⢠aftermarket, verify certifications for gasâ use and that the part is listedâ for yourâ appliance⤠model.
What precautions and postâinstallation checks should I perform after replacingâ the valve?
After âinstallation:⢠ensure all electrical connections andâ mounting hardware are secure, âŁrestore gas and⣠electrical power, âperform a thorough leak⤠test at âŁall⤠gas joints (use an approved leak â¤detectorâ or soapy â¤water), verify the oven ignites and cycles correctly across temperature settingsand monitorâ for a few cycles for proper operation. If âyou detect any gas odor â¤or abnormal behavior, shut off gas and power promptly and contactâ aâ qualified technician. For⤠safety and warranty reasons, keepâ documentation of the part⣠change and testing.
In Conclusion
The 316031501⢠Frigidaire oven valve is a critical component that regulates gas flowâ to the burner, directly âaffecting ignition â˘reliability, temperature control,⣠and overallâ applianceâ safety. Proper functionâ ofâ thisâ valve ensuresâ consistent cooking performanceâ and helps prevent unsafe conditions such as gas âŁleaks or erratic heating, making it âan integral part ofâ a well-maintained gas oven.
Accurate â˘diagnosis is essential when â˘valve-related â¤symptoms appear-such as lack âof heat, intermittent ignition, âor the smell of gas-to distinguish valve failure â˘from other possible causes. When âtesting confirms a âdefective valve, timely replacement âwith âthe correct component restoresâ performance and⣠mitigates â¤safety risks; work should be⣠performed orâ supervised by qualified service personnel who follow manufacturer guidelines and âsafety procedures.
the 316031501 âŁFrigidaire oven valve plays a central role in âŁboth âfunctionality and safety.Careful diagnosis,⢠adherence to proper ârepair practicesand â˘prompt replacement âwhen necessary help maintain âoven reliability, efficiencyand safe operation over the appliance’s â¤serviceâ life.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
