137006900 Frigidaire Washer Strike is a replacement door strike (alsoâ called a striker or strike plate) used on Frigidaire washing machines to receive and secure the door or lid latch.As a small but critical mechanical component mounted to the cabinet frame, the strike provides the physical engagement point for⣠the door latch bolt or âhook and helps maintain proper alignment between the door and the lock assembly.
Inside the appliance, â¤the strike is part of⢠the latch/lock subsystem and directly interfaces with the door latch, lock actuator or interlock switch and the cabinet sealing surfaces. âWhile typically a passive, non-electrical component, its correct position and condition areâ essential for the electrical lock mechanism and control board to register⤠a closed and secure door; misalignment, wearor⢠breakage of âthe strike can prevent the lock from engaging, trigger door-related error codesor allow the door toâ open during âa cycle. The strike also contributes to maintaining the door seal and preventing water leakage by ensuring consistent mating âof door and cabinet surfaces.
In this article you will find a technical overview of the 137006900 strike including its intended function and where it is used, compatibility considerations with Frigidaire washer models, common failure symptoms and diagnostic checks,⣠troubleshooting steps to isolate strike-related issuesand practical replacement considerations such as fitment, mountingand safety precautions to observe during service. The focus is on providing technicians, engineersand⢠appliance âowners the context âand inspection guidance needed to determine when the â¤strike âis the source of a problem and how to address it properly.
Table of Contents
- Function and Role ofâ the Washer⤠Strike inâ Frigidaire Door Latch and Control Safety systems
- How the 137006900 Frigidaire Washer Strike Operates â¤Within the Door Latch, Switch Assembly,â and Control Circuit
- Common Failure Symptoms: Mechanical Wear, Switch Faultsand Electrical Indicators of â˘Strike Failure
- Replacement considerations, Model Compatibilityand Troubleshooting Diagnostics for the 137006900 Frigidaire Washer Strike
- Q&A
- In Summary
Function and â˘Role of the Washer âStrike in Frigidaire âDoor Latch and Control Safety Systems
The 137006900 Frigidaire Washer Strike is the passive mechanical target mounted on the washerâ cabinet that âthe⢠door latch or lock assembly engages when⢠the door is closed. Functionally,the strike⣠aligns with the latch pawl or solenoid-actuated catch to â˘provide a positive,repeatable contact surface so⣠the door switch or lock detects a closed state. As the strike establishes the mechanical engagement point, its geometry and position directly effect whether the control sees the door as secured; misalignment, wearor⤠a cracked strike can produce intermittent lock signals, prevent cycle startor allow the âŁdoor to separate under â¤load during spin, creating a safety risk.
- Typical failure symptoms: door will not latch, persistent lock/door error codes, intermittent cycle stopsor noisy engagement.
- Inspection points: check for cracks, worn surfaces, correct axial alignment and secureâ fasteners.
- Replacement considerations: ensure hole pattern and striker profile match the original to maintain proper latch travel and switch actuation.
| Item | Description |
|---|---|
| Role | Provides the mechanical engagement point for the door âlatch/lock and ensures the control detects a closed door state. |
| Common failure mode | Wear,fracture,or misalignment resulting in⤠failure âŁto actuate the doorâ switch or incomplete⢠latch engagement. |
| Compatibility | Designed to replace the factory strike specified for washers listing part 137006900; verify model-specific parts lists or service manuals before â¤ordering. |
In practice, technicians verify the⤠strike by observing door/latch interaction: with the door open, engage the latch â¤manually to confirm smooth contact and with the door closed measure that the lock actuator or âmicroswitch registers the closed state. Repair steps typicallyâ include loosening the âstrike fasteners, repositioning for correct engagement (a small inboard/outboard or vertical adjustment can restoreâ reliable contact)and replacing the strikeâ if the mating surface is deformed.After replacement, run a quick diagnostic cycle or⢠door-lock test to⣠confirmâ that the âcontrol accepts the closed signal and that⣠the washer proceeds through lock and âspin phases without error.
How the 137006900 frigidaire Washer Strike Operates âWithin the Door Latch, Switch Assemblyand Control Circuit
the 137006900 Frigidaire Washer Strike is the⢠mechanical interface that locks into the âdoor latch and physically actuates âŁthe door âinterlock switch, allowing the washer’s control board to recognize a closed and secured door. In operation, the strike’s plunger⤠or cam rides against the switch actuator when the door isâ shut;⤠correct alignment⣠and stroke length close the switch contacts and complete the safety interlock. Because the strike is both a⣠mounting feature and an actuator, âcompatibility is steadfast by its boss spacing, plunger traveland the switch geometry in the latch assemblyâ – mismatches can⤠leave the switch partially actuated, causing âthe control to âŁreport an open-door or interlock fault even thoughâ the door appears closed.
Electrically,â the⤠strike itself is passive; its role is âŁmechanical actuation of the switch⢠that changes from open to closed (or toâ a resistive closed state) âŁand signals the control circuit. technicians typically verify âoperation by observing the switch closure with a multimeter while manually moving the striker through its âtravel and by checking for the control’s expected input voltage at the switch connector. Common practical indicators of a failing strike or misalignment⤠include intermittent door-locked âlights, failure â˘to start âŁa cycleor error codes related â¤to the door interlock.When replacing, confirm the 137006900’sâ mounting pattern matches the latch and that the actuator fully depresses the switch without binding.
- Typical âsymptoms: no start, intermittent âlocking, error codes for âdoor interlock.
- Field checks: verify mechanical travel, continuity of the switch during actuationand correct connector voltage at the control board.
- Replacement tip: match boss spacing and plunger stroke to the original strike for reliable switch actuation.
| Item | description |
|---|---|
| Function | Mechanical actuator that engages the latch and depresses the interlock switch to complete the control circuit. |
| Electrical interaction | Does not carry current; enables switch contact⤠closure that the control board senses as a closed-door input. |
| Compatibility factors | Mounting boss spacing, plunger strokeand switch geometry must match the existing latch/switch assembly. |
Common⤠Failure Symptoms: Mechanical Wear,Switch Faults,and Electrical Indicators of Strike Failure
The 137006900 Frigidaire washer âStrike is the mechanical catch and associated switching element⤠that secures the door during aâ wash cycle and provides the control board with a closed/open status. Functionally it must both engage the door striker and operate one or more âmicro switches or contacts so the controller receives a positive âdoor closedâ signal. Compatibility depends on the â¤latch geometry, mounting hole â˘patternand connector â¤pinout; even small differences in actuator length⤠or mounting â¤offset can prevent full engagement âand create intermittent faults. In a correctly matched assembly you will observe a solid mechanical engagement âand a distinct switchingâ action when the door is closed.
Common failure modes fall into three categories: mechanical wear of â˘the plastic or metal latch, switch contact failures inside the strike, â¤and electrical connector or wiring faults. Mechanical wear presents as excessive play, cracked tabsor misalignment that prevents â¤the latch from fully seating.Switch faults typically show up as⣠no continuity, intermittent contact when the actuator is depressed, âor corrosion on terminals. Electrical indicators include open circuits,shorted contacts,blown fuses or tripped protection,and lack of control-board voltage at the âŁstrike during a lock command.Practical diagnostics include a visual â¤inspection âfor broken parts, a manual actuation check to confirm consistent mechanical movementand a multimeter continuity test of âthe switch terminals while operating the latch; also verify the harness connector⤠for secure pins and the presence of the drive â¤voltage from the control board during a lock âŁcycle.
- Door will not latch or âwasher ârefuses to start
- Intermittent start/stop or aborts mid-cycle
- Audible click absent when door is closed
- Burned plastic smell or â¤discolored connector terminals
- Multimeter showsâ open circuit or intermittent continuity on switch terminals
| Item | Description |
|---|---|
| Mechanical play | Broken or worn latch components causing incomplete engagement |
| Switch continuity | Open or intermittent contacts indicated by multimeter when actuated |
| Wiring/connectors | Loose pins, corrosion, â˘or melted insulation producing loss of signal or voltage |
Replacement Considerations, Model Compatibilityand Troubleshooting Diagnostics for the 137006900 Frigidaire Washer Strike
Theâ replaceable latch component identified as 137006900 Frigidaire Washer Strike serves as the mechanical interface between the⤠washer door and the cabinet-mounted latch assembly, transferring the physical motion of the door to⤠the door-closed sensor circuit on the control âboard.⢠The strike’s geometry, mounting hole spacingand âactuator travel determine fit and reliable engagement; replacements must match the original part’s plunger length and â¤strike face orientation to ensure the door closes⣠without⢠binding.⣠Technicians should compare the new part to the old unit visually and â¤against the washer’s model/serial documentation rather than relying solely on part numbers, sence different production â¤runs can use visually similar strikes with different mounting footprints or electrical connector styles.
- Common â˘symptoms: door won’t register closed, intermittent lock, door pops open during spinor specific door-lock error codes.
- Quick checks: inspect⤠for broken plastic tabs, wear on⤠the striker surface, debris in the latch pocketand door sag that prevents proper â¤engagement.
- Electrical diagnostics: with the harness â˘disconnected, manually actuate the strike and measure the control harness for the expected continuity or closed-circuit signal; inspect wiring for corrosion â˘or damaged insulation.
- Installation tips: confirm screw pattern and actuator orientation, âverify that the strike â¤actuates the door-closed microswitchâ cleanlyand torque fasteners to avoid distortion.
| Item | Description |
|---|---|
| Part | 137006900 Frigidaire Washer⢠Strike -â mechanical door strike/latch actuator (verify form factorâ before ordering) |
| Function | Provides mechanical engagement and completes the door-closed signal to⣠the washer control |
| Typical failure modes | Plasticâ wear/breakage, misalignment from door sag, debris interferenceor â¤loss âŁof electrical continuity to switch |
For troubleshooting, start by reproducing the fault âand observing whether the strike physically moves and contacts the switch; if the strike motion is hindered but the switch still changes state, the strike geometry is likely incorrect and will require replacement with aâ matching unit. If the strike âmoves freely but theâ control never registers a closed signal, trace the wiring to the control board and test continuity or voltage presence at the connector âŁduring actuation; â¤intermittent signals often point to connector corrosion or a fatigued microswitch.⣠When ordering replacements, cross-reference â˘the appliance model number and inspect mounting dimensions and connectorâ type to avoid âreturns due to incompatible form factors.
Q&A
What is the 137006900 Frigidaire â¤Washer Strike and what does it do?
The 137006900 is the door/lid strike⤠(catch) used on certain Frigidaire washers.It is â˘a mechanical piece mounted to the cabinet that the door latch or lock engages with to hold âthe door closed and keep the washer in the correct state to run. It does not contain electrical components⣠– it provides a mating surface and alignment for the door latch/lock assembly.
What âŁsymptoms indicate the strike (part 137006900) is bad orâ needs replacement?
Common symptoms include the door not staying closed or feeling loose, the washer refusing â˘toâ start or showing a door-lock error, intermittent lockingor visible damage âto the strike such as cracked⣠or broken tabs. As the strike is a passive part,⢠electrical door-lock failures are usually caused⣠by the latch/lock, butâ a broken or worn strikeâ can prevent proper engagement and â˘trigger errors.
How do I verifyâ whether the⣠strike or the door latch/lock is the problem?
Visually inspect the⤠strike for cracks, worn surfacesor broken mounting tabs.With the door⤠open, check that the latch on⤠theâ door lines up and fully âŁengages the strike when closed. If alignment and condition appear â¤OK but the washer still reports a lock error, the door latch/lock (the electricalâ component) â¤might potentially be faulty.⤠As the strike has no electrical connections, â˘you cannot test it with a multimeter – rather rely on mechanical inspection and checking alignment and movement.
Is âŁreplacing the 137006900â strike a tough repair and what tools are required?
Replacement is generally âŁa basic to moderate DIY repair. Typical tools are âa screwdriver (Phillipsâ or⢠Torx,depending onâ model) and possibly â˘a socketâ set. Steps normally include unplugging the washer, opening âthe door, removing a few screws â˘that secure the strike to the cabinet or door frame, swapping in the new strike, aligning it âso the latch engages smoothlyand âŁthen testing operation. Exact disassembly steps vary by model, so consult your washer’s service manual or⣠parts diagram first.
How do I align the new strike to ensure the door latches correctly?
Loosely âinstall the strike screws so you can adjust its position. Close the door to see â˘where the latch contacts the strike, then shift the strike until the latch fully⣠engages without â¤forcing the door.Tighten the screws âwhile keeping⢠the strike in that position. After tightening, open and close the door several times and runâ a short cycle to confirm the door locks and unlocks properly. If there’s resistance or the âlatch⣠misses the strike, â¤loosen and re-adjust.
Will replacing the â˘strike fix door-lock error codes on the washer?
Sometimes – if the error is caused by the â˘door not mechanically engagingâ (due to a broken or misaligned strike), replacing âŁor realigning the strike willâ resolve the issue. However, if the error is due to a faulty door lock/latch assembly, wiring, âor control board,⢠replacing the â˘strike alone âwill not fix it. Diagnose byâ visual inspection and testing the lock assembly; if the lock has electrical failure, it âŁwill need replacement or further electrical troubleshooting.
How do I ensure I buy the correct â137006900 strike for myâ washer?
Use your washer’s full model numberâ (found on the door frame, back panelor inside the console) to confirm parts compatibility. Cross-reference that model number with the part number 137006900 on Frigidaire’sâ parts lookup, a parts dealeror the washer’s parts diagram. Even if the part number matches, âverify images and mounting hole locations to ensure it fits your specific model year andâ cabinet style.
Are there temporary fixes I can use until I replace âthe strikeand are there any safety concerns?
Temporary fixes are not recommended because a damaged strike can allow the door to open during a cycle, which is unsafe. If you must run the washer before replacement,â avoid high-speed spin cycles, load lightlyand supervise the âmachine, but this⣠is not a reliable or âsafe âŁlong-term solution. Always disconnect power before âŁservicingand do not attempt repairs if you are unfamiliar with appliance safety. âŁIf in âdoubt, contact âŁa qualified appliance technician.
in Summary
The â¤137006900 Frigidaire washer strike is a smallâ but critical component â¤that helps secure â¤the door and confirm proper latch engagement, allowing theâ machine to begin and complete programmed cycles safelyâ andâ reliably.⤠Its correct operation âcontributes to user safety, effective waterâ containmentand the washer’s ability to detect that the door is closed and locked âbeforeâ starting â¤or continuing a⤠cycle.
Because symptoms of a failing strike-such as a door that won’t lock, interrupted cyclesor â˘error⢠codes-can also indicate problems elsewhere in the door assembly, control boardor âwiring, accurate diagnosis is crucial. Verifying the cause with visual âinspection,â continuity testingand reference â˘to â¤service documentation reduces unnecessary parts replacement and downtime.
When replacement is â˘required, using the correct 137006900 part or an approvedâ equivalent, installing it per manufacturer guidelinesandâ performing post-repair checks will restore function and minimize repeat failures. Proper diagnosis, careful replacementand functional testing together ensure a safe, reliable repair and help extend the operating life of âthe appliance.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
