241860810 Frigidaire Refrigerator Ice Container Assembly is a molded ice storage and handling component used in compatible frigidaire freezer modules; it functions as the receptacle that receives, stores and presents harvested ice from the ice maker for manual retrieval or for delivery through an external dispenser. Mechanically it is indeed not an active powered device on its own but is a subsystem assembly that typically includes the bin cavity,mounting tabs or brackets,and the interfaces required for an auger or dispenser drive to engage and for ice-level sensors or trip arms to operate.
Within the appliance the ice container assembly sits between the ice maker module and the dispenser or user-access area and therefore interacts directly with the ice production, dispensing and control systems. It must align with the ice maker discharge chute, provide clearance and guidance for ice flow, and accommodate auger couplings or actuator shafts on models with automatic dispensing. The bin also frequently incorporates provisions for ice-full detection (mechanical trip arm or electronic sensor) and for sealing or channeling ice to prevent bridging and excessive frost; its condition and alignment affect ice production control, dispenser motor loading and the reliability of sensor signals to the control board.
In this article readers will find a technical overview of the 241860810 assembly including its intended function and typical installation location, guidance on compatibility checks (model families, mounting points and dimensional checks), common failure symptoms (cracked or warped bin walls, broken mounting tabs, ice bridging, auger bindingand incorrect sensor actuation), structured troubleshooting steps to isolate mechanical versus control faultsand practical replacement considerations (verifying OEM part numbers and revisions, handling and installation precautions, and tests to confirm correct mechanical engagement and sensor operation after fitment).
Table of Contents
- Function and Role of the Ice Container Assembly in Refrigerator Ice Production and Storage
- How the 241860810 Frigidaire Refrigerator Ice Container Assembly Integrates with the Ice maker,dispenser and Internal Airflow
- Common Failure Symptoms and Diagnostic Indicators for the Ice Container Assembly
- Replacement Considerations,Model Compatibility,and Installation Procedure for the 241860810 Frigidaire Refrigerator Ice Container Assembly
- Q&A
- The Conclusion
Function and Role of the Ice container Assembly in Refrigerator Ice Production and Storage
The 241860810 Frigidaire Refrigerator Ice Container Assembly functions as the receptacle and interface between the refrigerator’s icemaker and the user-accessible ice delivery area. It collects ice discharged from the icemaker, provides short-term storage, and aligns with the dispenser chute or door-mounted auger so that the icemaker can continue production without backflow or jamming. The bin is typically molded from a food-grade polymer with defined mounting tabs, a sensor recess (for a mechanical bail arm or optical/proximity sensor)and drainage channels to route meltwater back to the evaporator area. A cracked bin, warped mounting tabor obstructed sensor recess can produce false “bin missing” signals or allow ice bridging, which will halt production or cause feed failures; technicians should check bin alignment and sensor engagement as part of diagnostics for intermittent ice production problems.
Functionally,the assembly contributes to the refrigerator’s freeze-thaw balance by limiting air exchange around stored ice and preventing large ice masses that can jam the dispenser. Compatibility is resolute by dimensional fit, mounting tab spacingand the sensor interface rather than cosmetic shape; replacing with part 241860810 will restore proper mechanical and sensor interactions only when those parameters match the refrigerator’s ice maker geometry. For service tasks, remove the bin to inspect for cracks, excessive frost buildupor foreign objects in the sensor recess and verify that the dispenser auger and chute clearances are within tolerance.Replacing the bin is a common repair when failures trace to physical damage or persistent ice bridging rather than electrical faults in the icemaker module.
- Primary features: sensor recess, mounting tabs, drain grooves, removable lid or cover interface.
- Common symptoms of a failing bin: false “bin missing” errors, ice jams at the chute, excessive frost or standing meltwater in the bin.
- Service checks: inspect alignment, measure tab spacing, confirm sensor engagementand check for material deformation.
| Item | Description |
|---|---|
| Part number | 241860810 |
| Material | Food-grade thermoplastic (molded bin) |
| Typical capacity | Approximately 2-4 lbs of ice (model-dependent) |
| Interface | Mounting tabs and sensor recess (bail arm or optical/proximity) |
| Compatibility | designed for specific Frigidaire/related models-verify refrigerator model number before replacement |
How the 241860810 Frigidaire Refrigerator Ice Container Assembly Integrates with the Ice Maker,Dispenser and Internal Airflow
The 241860810 Frigidaire Refrigerator Ice Container Assembly functions as the mechanical and electrical interface between the ice maker module,the dispenser mechanism,and the freezer cabinet’s airflow pathways. When the ice maker harvests cubes, they drop into this container where its geometry and mounting points align the ice stream with the dispenser auger or paddle; a bin-full actuator or optical switch mounted to the assembly communicates status to the refrigerator control board so the ice maker stops production when capacity is reached. The assembly’s chute opening, auger coupling recessand any integrated guide vanes must match the dispenser drive and chute geometry precisely-incorrect alignment will prevent proper engagement or cause grinding at the auger coupling even if the motor and ice maker are otherwise functional.
Airflow management and thermal behavior around the container affect ice quality and dispensing reliability. The bin is designed to allow cold air circulation from the freezer evaporator and to limit warm door-air infiltration that causes partial thawing and ice bridging; blocked vents,poor door seals,or an improperly seated bin will promote clumping and dispenser jams. For practical troubleshooting, technicians should verify correct mechanical seating, confirm the bin-full switch continuity or optical sensor alignment, inspect for frost accumulation on the bin walls and augerand ensure the dispenser drive engages the auger coupling without excessive play.
- Mechanical interfaces: mounting tabs, auger coupling recessand chute alignment determine dispenser engagement.
- Sensing: integrated bin-full switch or optical sensor provides occupancy feedback to the control board.
- Airflow effects: designed openings permit evaporator airflow while minimizing warm-air ingress that causes bridging.
- Compatibility: must match model-specific bracket geometry and connector types to function correctly.
| Item | Description |
|---|---|
| Mounting interface | Model-specific brackets and tab locations that align the chute and auger coupling. |
| Sensor type | Mechanical actuator or optical sensor for bin-full detection; electrical connector to control board. |
| Typical capacity | Container volume sized to the ice maker’s harvest rate; actual capacity varies by refrigerator model. |
Common Failure Symptoms and Diagnostic Indicators for the Ice Container Assembly
The 241860810 Frigidaire refrigerator Ice Container Assembly is the removable ice storage and interface component that receives ice from the ice maker,aligns the auger coupling for dispensing,and frequently enough provides a mechanical or optical presence signal to the control board. Its normal behavior is to present a smooth internal surface and correct axial alignment so the auger can rotate freely; deviations in those behaviors are primary diagnostic indicators. Such as, repeated thaw/refreeze cycles can produce bridged or clumped ice that prevents the auger from transporting cubes, while a cracked or warped bin can allow ice to jam against the auger housing or fail to engage the dispenser drive coupler. Verify model compatibility with the refrigerator service manual before assuming interchangeability, since mounting tabs, coupler spline counts, and sensor locations vary across Frigidaire platforms.
- Ice bridging or hard clumps - inspect for frost/freeze layers, empty the bin and break up ice; observe whether the problem recurs after normal temperature stabilization.
- auger binds or makes grinding noise – check for physical obstructions, damaged auger splinesor stripped coupler teeth at the bin interface.
- Water pooling or leaking beneath the bin – look for cracks in the bin shell or misalignment that allows melted ice to escape instead of draining to the evaporator pan.
- Bin-detect error or dispenser refuses to operate – test the presence switch or optical sensor continuity and confirm the bin seats fully in its mounting flange.
- excessive frost buildup inside the bin – verify freezer temperature and door seal integrity; abnormal humidity or frequent door openings accelerate frost formation.
| Item | Description |
|---|---|
| Part | 241860810 Frigidaire Refrigerator Ice Container Assembly |
| Primary function | Ice collection, auger coupling interfaceand bin-presence signaling |
| Common indicators | Ice clumping, auger binding, leaks, bin-detect errors |
| Compatibility note | Verify model compatibility with the refrigerator service manual-mounting geometry and coupler design must match the ice maker and dispenser. |
Practical diagnostic flow for a technician: perform a visual inspection for cracks or deformations, remove the bin and manually rotate the auger to check free movement, run a dispense test with the bin seated and monitor for control board error codesand measure continuity or actuation of the bin-detect sensor if accessible. In a typical field example, persistent dispensing jams after clearing clumped ice often point to a worn coupler spline or a misaligned bin flange rather than the ice maker itself; replacement of the 241860810 container and retest of seating and spline engagement resolves the mechanical interface faults. Document observed symptoms, compare against the service manual alignment specificationsand replace the container if structural damage or irreversible deformity is found.
Replacement Considerations, Model Compatibility, and Installation Procedure for the 241860810 Frigidaire Refrigerator Ice Container Assembly
The 241860810 Frigidaire refrigerator Ice Container Assembly functions as the receptacle and interface between the icemaker module and the user-accessible ice storage.It captures and holds cubed or crushed ice, provides the mounting features that align the icemaker’s discharge chuteand-on dispenser-equipped models-houses the interlock and auger drive interfaces. Technicians should verify that mating surfaces, rail locationsand any electrical or mechanical connector locations match the replacement part; visual comparison and measurements of mounting points are necessary because nominally similar bins can differ in sensor placements, chute geometry, or clearance that will affect ice flow and dispenser operation.
Replacement requires basic disassembly, mechanical alignmentand functional testing: power should be removed before disconnecting any electrical interlocks or removing the old bin, the new assembly must be seated so rails and guides engage fullyand any door or bin switches must be reconnected and verified for correct actuation. After installation, manually cycle a few harvest cycles or dispense a small amount of ice to confirm there is no binding, ice jammingor false sensor signals; if the refrigerator includes an auger or motorized dispenser, verify the drive coupling engages without axial play. Practical considerations include checking for frozen bridges at the chute, ensuring the bin drains and vents align with cabinet featuresand swapping sensors or seals only when dimensions and terminal types match.
- Verify part fit: compare mounting holes, rail spacingand connector style to the original.
- Power off: remove mains power before disconnecting wiring or handling dispenser electronics.
- Seat the bin fully and check switch actuation and chute clearance before returning power.
- Perform functional tests: harvest cycle, dispense testand visual inspection for leaks or ice bridges.
| Item | Description |
|---|---|
| Part number | 241860810 (ice container / storage bin) |
| Primary function | Store ice and interface with icemaker discharge and dispenser mechanisms |
| Compatibility checks | Match rail spacing, chute alignment, switch/connector typeand cabinet clearance |
Q&A
What is the 241860810 Frigidaire Refrigerator Ice Container Assembly?
The 241860810 is an OEM ice container (ice bin) assembly designed for certain Frigidaire refrigerators. It collects and stores ice produced by the refrigerator’s automatic icemaker and provides the mounting/guide interface between the icemaker and the dispenser (when present). The assembly is typically a molded plastic bin shaped to fit the freezer cavity and may include features such as a fill-level arm,guide rails,or alignment tabs depending on model.
How do I know if 241860810 is compatible with my Frigidaire refrigerator?
Verify compatibility by checking the refrigerator model number (usually on a sticker inside the fresh food compartment or on the freezer wall) and cross-referencing it with Frigidaire’s parts lookup or the parts supplier’s compatibility table. You can also compare the part number printed on your existing ice container. If in doubt,provide the appliance model number to the parts dealer or Frigidaire support for confirmation.
How do I remove and install the ice container assembly safely?
Typical removal: open the freezer,turn off the icemaker (or unplug the refrigerator) to prevent the motor from running,slide the ice container out along its rails or disengage the retaining tab,and lift it free. To install: align the bin with its guides, slide it fully into place until it seats and any retaining clip engages, then turn the icemaker back on. Use a screwdriver only if screws or fasteners are present. Always follow the model-specific service instructions in the user manual to avoid breaking plastic tabs or damaging sensors.
My ice is clumping or freezing into one block in the bin – can the container assembly cause that?
The container itself does not cause freezing by temperature, but design issues (poor airflow or a cracked bin allowing moist air in) can contribute. More common causes are excessive humidity in the freezer, frequent door openings, a failing door gasketor freezer temperature too low or too variable. Empty and dry the bin, set freezer temperature to about 0°F (-18°C), check door sealsand avoid leaving the freezer open. If the bin is damaged or warped and allows moisture intrusion, replace it.
What cleaning and maintenance steps are safe for the ice container?
Remove the bin and empty all ice before cleaning. Wash with warm water and mild dish soap; rinse thoroughly and let air dry entirely before reinstalling to avoid introducing moisture. Do not use abrasive cleaners, strong solventsor bleach unless manufacturer guidance permits them. If ice tastes or smells bad, clean the bin and freezer, discard old iceand run a few cycles to make fresh ice. Periodically inspect the bin for cracks or sharp edges.
Why is the icemaker not filling the ice container even though it makes ice?
Possible causes include misalignment of the ice container (ice may miss the bin), an obstructed path, a broken or misadjusted fill-level arm or sensor that stops the icemaker earlyor the dispenser chute being blocked. Check that the bin is correctly seated and not cracked, clear any ice jams between the icemaker and container, and confirm the fill-level mechanism is working. If the sensor or motor is faulty,additional diagnostic steps or replacement components may be needed.
Can I use an aftermarket ice container instead of the OEM 241860810?
Aftermarket bins may fit and function, but they vary in material quality, dimensionsand tolerances.Using a non‑OEM part can result in poor fit, ice spills, noise, or interference with sensors and dispenser mechanisms. For best reliability and fit,use the OEM 241860810 part or a verified equivalent that explicitly lists compatibility with your refrigerator model.
What should I inspect if the ice container is leaking or causing noise?
Inspect the bin for cracks, warped edges, or broken mounting tabs that let ice or water escape. Check that it is fully seated on its rails and not rubbing against the evaporator cover or othre components. noise can also come from ice hitting the bin at an odd angle – verify icemaker alignment and that the chute or guide is intact. If electrical noise or motor noise is present, confirm whether it is indeed coming from the icemaker motor rather than the bin; replace the bin only if it is physically damaged.
The Conclusion
The 241860810 Frigidaire Refrigerator Ice Container Assembly serves as a critical component in the ice storage and dispensing system, providing a secure, sanitary receptacle for produced ice and the mechanical interface necessary for reliable dispensing. Proper fit and function of this assembly support consistent ice production, prevent spillage and contaminationand help maintain the overall efficiency and longevity of the refrigerator’s freezer compartment.
Timely and accurate diagnosis of issues related to the ice container-such as unusual sounds,ice jams,leaking,misalignment,or visible cracks-helps determine whether repair or replacement is required. Addressing the root cause, rather than only treating symptoms, reduces the risk of recurring problems and prevents collateral damage to adjacent components like the auger, dispenser motorand ice maker assembly.
When replacement is necessary, using the correct 241860810 assembly and following manufacturer installation guidance or engaging a qualified technician ensures compatibility and restores proper operation. Proper installation, testingand routine inspection after replacement will maximize performance, maintain hygieneand contribute to the reliable function of the refrigerator over time.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
