807117001 Frigidaire Dishwasher Drain Hose is a flexible wastewater conduit used on Frigidaire residential dishwashers; it is indeed a serviceable outlet hose that connects the dishwasher’s drain pump or sump outlet to an air gap, sink tailpiece, or garbage disposal. The component is typically made from reinforced rubber or corrugated PVC adn is fitted with barbed or stepped ends secured by worm‑gear clamps or similar fasteners.As a simple mechanical plumbing component, it is specified for hot wastewater exposure, repeated flexing, and resistance to detergents and food particulates, and it is manufactured to match the drain interface and routing constraints of the appliance model for which it is supplied.
Inside the appliance, the drain hose functions as the primary path for discharged water from the drain pump to the household drain system and therefore interacts directly with the dishwasher sump, drain pump outlet, check valve arrangements, air gap or high‑loop anti‑siphon configuration, and the sink/disposal plumbing. Proper hose diameter, internal flow capacity, bend radius, and secure connections are critical to prevent backflow, ensure complete evacuation of wash water, and avoid pressure losses that can cause standing water or pump overload. Mechanical failures of the hose-such as kinking, cracking, abrasion from routing, or clamp failure-can lead to leaks, blockages, odors, or error codes that effect overall appliance operation.
In this article readers will find a technical overview of the 807117001 drain hose including its intended function, common compatibility considerations, and how it integrates with associated systems. The piece will describe typical failure symptoms (slow draining, residual water, visible leaks, unusual noises), basic troubleshooting checks (visual inspection, routing and clamp verification, blockage location), and practical replacement considerations such as matching hose length and fitting type, securing and routing for a high loop or air gap, material and temperature resistance, and safety steps to take before service. The intent is to provide technicians, engineers, and appliance owners with the facts needed to diagnose hose‑related problems and select an appropriate replacement while maintaining correct plumbing and service practices.
Table of Contents
- Functional Role and Fluid-Flow responsibilities of the Dishwasher Drain Hose
- How the 807117001 Frigidaire Dishwasher Drain Hose Integrates with the Pump, Air Gap, and Disposal Line
- Common Failure Modes and Diagnostic Symptoms of Drain Hose Malfunction
- Replacement Considerations, Installation Procedure, and Model Compatibility Notes
- Q&A
- Final Thoughts
Functional Role and Fluid-Flow Responsibilities of the Dishwasher Drain Hose
The drain hose directs pump-displaced wastewater from the dishwasher sump to the household drain or garbage disposal, and the 807117001 Frigidaire Dishwasher Drain Hose is engineered to perform that function reliably under cyclic pressure pulses, hot water, and common detergent chemistries. Its construction-typically a reinforced, flexible tube with standardized connector ends-must preserve an open flow path while resisting kinks, collapse, and chemical degradation; the hose works in concert with the dishwasher discharge pump, the high loop or air gap, and the sink-side plumbing, so correct routing and secure clamping are essential for predictable hydraulic behavior and to prevent backflow or siphoning into the appliance.
In service, technicians assess compatibility by confirming connector type and effective length, inspecting for external damage, and verifying that the hose maintains diameter under pump pulses. Practical indications that the hose requires service include persistent slow drainage, wetness or dripping at clamp points, hardening or cracking of the material, and unusual odors from retained water; replacement typically involves matching the hose to the machine’s outlet fitting, maintaining the required high-loop or air-gap elevation, and using corrosion-resistant clamps to secure both ends. Below are core responsibilities to check during inspection and a short technical reference for common attributes.
- Convey wastewater from the dishwasher pump to house drain or disposal without restriction.
- Resist heat, detergents, and mechanical fatigue to avoid leaks or collapse.
- Provide compatible connection interfaces for Frigidaire equipment and common disposals/standpipes.
- Enable proper routing for a high loop or air gap to prevent backflow into the appliance.
- Maintain sufficient flexibility to route under cabinets while resisting kinks.
| Item | Description |
|---|---|
| Construction | Reinforced flexible tubing (rubber or corrugated plastic) designed for detergent and heat resistance |
| Compatibility | designed for Frigidaire dishwashers requiring this replacement hose model; verify connector type and length |
| Service indicators | Leaks at clamps, visible cracks/hardening, slow drain, or pinch/kink points |
How the 807117001 Frigidaire Dishwasher Drain Hose Integrates with the Pump, Air Gap, and Disposal Line
The 807117001 Frigidaire Dishwasher Drain Hose attaches directly to the dishwasher pump outlet and provides the pressure and gravity path for wastewater to leave the appliance. Correct integration requires matching the hose inner diameter and end fitting to the pump discharge spigot, a secure clamp to prevent leaks under pump pulsation, and routing that prevents backflow or siphoning-either through a dedicated countertop air gap or by creating a sufficiently high loop above the sink drain. The hose must tolerate the pump’s intermittent pressure pulses and resist kinking; an undersized, crushed, or poorly secured hose will cause slow drainage, intermittent leaks at the pump flange, or push-back into the basin during drain cycles.
- Connection: correct diameter and clamp to pump discharge
- Routing: air gap or high loop to prevent backflow
- Disposal interface: knockout removed and secure connection to disposal inlet
- Maintenance: inspect for clogs, crimps, or deterioration that reduce flow
| Item | Description |
|---|---|
| Pump discharge | Usually a molded spigot requiring a hose with matching ID and a worm-gear clamp to maintain a sealed connection under pulsation. |
| Air gap / high loop | Air gap physically separates dishwasher outflow from sink plumbing to block backflow; a high loop is an choice that relies on elevation above the sink drain. |
| Disposal connection | Attach to the garbage disposal inlet after removing the factory knockout; ensure the hose ties off above the trap to avoid siphoning. |
| Material & durability | Flexible, kink-resistant rubber or reinforced plastic that resists grease, heat, and repeated bending; replace if cracked or permanently deformed. |
Technicians replacing or troubleshooting the hose should verify model compatibility and confirm the route and termination are correct: a hose that meets the pump outlet spec but is routed below the sink drain will permit backflow and odor; a hose clamped loosely will leak at the pump flange.Practical checks include running the drain cycle while observing for pulsation leaks, confirming the disposal knockout is removed and connected above the trap, and replacing the hose if internal buildup or external damage restricts flow-this restores expected drain performance without altering pump operation or disposal configuration.
common Failure Modes and Diagnostic Symptoms of Drain Hose Malfunction
The 807117001 Frigidaire Dishwasher Drain hose functions as the pressurized and gravity-assisted path that removes wash and rinse water from the tub to the household drain. Common mechanical failure modes are internal fouling (food debris, grease, calcium buildup) that reduces flow, kinking or compression from incorrect routing that restricts cross-sectional area, and brittle cracking or pinhole leaks that develop in aged PVC or corrugated materials. Compatibility issues arise when a replacement hose has a different internal diameter, connector profile, or lacks a required one-way/check valve; such mismatches can produce poor seals, backflow into the tub, or persistent drainage problems. Typical indicators that point to a hose-related fault include slow drain cycles, standing water in the tub, intermittent leaks around hose fittings, and audible gurgling or siphon-like sounds during pump operation.
- Slow draining or partial drain after a cycle
- Water pooling in the dishwasher base or on the floor near hose connections
- Gurgling noises or sputtering during pump operation
- Intermittent leakage at hose clamps or along the hose length
- Backflow into sink or disposal when sink is used
| Item | Description |
|---|---|
| Clog/Fouling | Debris or grease build-up reduces flow rate and causes standing water |
| Kink/Crush | Improper routing or tight bends reduce effective lumen and impede drainage |
| crack/Leak | Material fatigue or puncture leads to pressure-dependent leaks, often at clamps |
Diagnosing hose faults requires both visual and functional checks: inspect the entire hose length for visible damage, deformity, or buildup; remove the hose and pass water or compressed air through it to verify unobstructed flow; and confirm that clamps and fittings are correctly seated and torque-limited to prevent thread or nipple damage. For replacements, match internal diameter and connector style to the original specification, ensure proper length and routing to maintain a continuous uphill run where required, and verify presence or orientation of any integrated check valve to prevent sink backflow. In practice, a blocked but intact hose will clear with flushing or mechanical cleaning, whereas cracks, permanent deformations, or mismatched fittings mandate replacement to restore reliable drainage and sealing.
Replacement Considerations, Installation Procedure, and Model Compatibility Notes
The 807117001 Frigidaire Dishwasher Drain Hose is a molded flexible conduit that conveys pump discharge from the dishwasher chassis to a household drain, garbage disposal, or sink tailpiece. Constructed of heat- and chemical-resistant thermoplastic or reinforced rubber, the hose must maintain a consistent internal diameter and secure fittings to prevent backflow, siphoning, or leakage; failures typically present as slow draining, water pooling at the base, or intermittent leaks at the connection points. inspect the hose for kinks, soft spots, and hardened sections during replacement – a collapsed section reduces flow and increases pump load, while incorrect connector styles (barb vs. threaded) or diameters create leak paths even when clamps appear tight.
During replacement and installation, confirm mechanical compatibility with the dishwasher inlet and the household drain connection, and follow good routing practice to preserve the pump’s hydraulic performance: avoid sharp bends, maintain a high loop (or air gap) above the sink cabinet, and secure the hose to prevent rubbing or sagging. Typical installation workflow includes verifying part fit, disconnecting power and water, draining residual water, removing clamps, clearing any blockages, routing the hose with the high loop, applying new clamps, than running a test cycle while checking for leaks and proper drain time; using a slightly longer hose reduces the risk of tension but excess length should be coiled without creating traps. Practical compatibility notes: OEM designation 807117001 ensures factory fit for the original Frigidaire models listed on service parts sheets, but universal hoses can work if inner diameter, connector type, and temperature rating match; adapters might potentially be required for disposal tailpieces or non-standard fittings.
- Pre-install checks: verify inner diameter, connector type, and temperature/chemical ratings.
- Routing: maintain high loop/air gap and avoid sharp bends or compression under cabinets.
- Sealing: use corrosion-resistant clamps and inspect for soft/hardened hose material.
- Testing: run a full drain cycle and inspect all joints for seepage or pump cavitation sounds.
| Item | Description |
|---|---|
| Material | Reinforced thermoplastic or EPDM-type rubber; resists 60-85°C short-term exposure and detergents |
| Typical Inner Diameter | Matches dishwasher pump outlet; verify manufacturer spec for exact size |
| Connector Types | Barbed, plain slip-fit, or threaded – may require clamp or adapter |
| Function | Conveys wastewater, prevents backflow when routed with high loop or air gap |
Q&A
What is the 807117001 Frigidaire dishwasher drain hose and what does it do?
The 807117001 is a replacement drain hose manufactured for Frigidaire dishwashers. It carries wastewater from the dishwasher drain pump to the household drain, garbage disposal, or air gap. It is indeed an OEM part intended to match the original equipment in fit and function.
How do I know if 807117001 is compatible with my Frigidaire dishwasher model?
Check your dishwasher model number (usually on the door frame or inside the door) and compare it to the appliance parts list or Frigidaire parts lookup. The part number 807117001 is an OEM drain hose used on a range of Frigidaire models, but you should confirm compatibility by searching the model number in the manufacturer’s parts database or by contacting an authorized parts supplier.
Can I install the 807117001 hose myself, and what basic tools are required?
Yes, a competent DIYer can install it. Required tools are typically pliers (or a screwdriver for worm-gear clamps), a bucket or towels to catch water, and possibly a nut driver if removing the dishwasher is necessary.Always disconnect power to the dishwasher (turn off breaker) before starting work and turn off the water if you need to move the unit.
What are the basic steps to replace the drain hose safely?
Turn off power at the breaker, slide the dishwasher out if necessary, place a towel/bucket under connections, disconnect the old hose from the pump and the household drain/disposal, remove clamps, install the new hose onto the pump outlet and the drain/disposal or air gap, secure with clamps (use new clamps if old are corroded), form a high loop or install an air gap per local code, push the dishwasher back and restore power, then run a short cycle and check for leaks.
How do I clear clogs from the 807117001 drain hose without damaging it?
Frist try removing the hose and flushing it with hot water. Use a long flexible brush or a length of plumbers’ tubing to dislodge debris. Avoid using chemical drain cleaners (they can damage the hose and dishwasher components) and do not use heavy metal drain snakes inside the hose as they can puncture it.If the clog is in the dishwasher pump or disposal, address those components as well.
What are common causes of leaks with this drain hose and how can I prevent them?
Leaks usually result from cracked or pinched hose, loose or corroded clamps, improper connections, or kinks that stress the hose. Prevent leaks by inspecting the hose for cracks or wear,replacing damaged hoses,using properly sized clamps (tighten securely but do not over-tighten),ensuring no sharp bends or kinks,and maintaining a high loop or air gap to prevent backflow.
Can I trim the 807117001 hose to fit, and are there any precautions?
You can trim excess length if necessary, but only cut a small amount from the outlet end and make sure the cut is clean and square. Do not cut through any molded fittings or reinforcement.After trimming, use an appropriate clamp and ensure the hose stays free of kinks. If you must shorten significantly, verify that you still have enough length to form a proper high loop or reach an air gap.
Is the 807117001 hose covered by warranty and where can I buy an authentic replacement?
Warranty coverage depends on the seller and the age of the appliance; OEM parts may carry a limited warranty from the seller or manufacturer.Buy authentic replacements from Frigidaire-authorized parts dealers, major appliance parts retailers, or directly from the manufacturer to ensure you receive a genuine OEM hose. Keep receipts and warranty information in case of defects.
Final Thoughts
The 807117001 Frigidaire dishwasher drain hose plays a basic role in channeling wastewater from the dishwasher to the household drain system. As a functional plumbing component, it helps maintain effective draining, prevents backflow, and contributes to overall appliance hygiene and performance. A properly functioning drain hose is therefore essential to reliable daily operation and to avoiding water-related damage to the appliance and surrounding areas.
Accurate diagnosis is important when troubleshooting draining problems or leaks. Symptoms such as slow draining, visible cracks or kinks in the hose, persistent odors, or water on the floor can indicate hose failure, but similar signs may also stem from pump, disposal, or clog issues. Verifying the hose as the root cause and confirming the correct part number and fit helps ensure that any corrective action addresses the actual problem.
When replacement is warranted, using the correct 807117001 part and following manufacturer guidelines or the services of a qualified technician helps restore proper function and reduce the risk of recurring issues or water damage. Routine inspection and timely replacement of a compromised drain hose support dishwasher efficiency, prolong appliance life, and reduce the likelihood of costly repairs.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
The Blincoo Elite 48" Heavy Duty Dog Rope Toy is made for large breeds that love tug-of-war, chewing, and active play. Strong, simple, and fun for powerful dogs.
Shop on TikTok