137006900 Frigidaire Washer Strike is a replacement striker or “strike plate” used in Frigidaire washing machines; it is the mechanical receptacle mounted on the cabinet that the door’s latch or catch engages when the washer door is closed. The part is typically a small metal or reinforced plastic component fastened to the door opening or inner cabinet, designed to align precisely with the door latch so the latch can secure the door and, in machines that use it, operate the door-interlock mechanism.
Inside the appliance, the strike works directly with the door latch or lock assembly and indirectly with the machine’s safety interlock and control systems. Proper engagement of the latch with the strike establishes a closed-door condition that allows the control board to enable wash, spin and fill cycles; a misaligned or damaged strike can prevent the latch from seating, interrupting the interlock circuit and stopping operation. The strike therefore plays both a mechanical role (holding the door closed under load and vibration) and an operational role (ensuring the electrical or mechanical interlock can report a secure door to the control system).It is mounted at the door opening and interfaces with the door frame, latch hardware and, in some designs, the door gasket and hinge alignment.
In this article readers will find a technical review of the 137006900 Frigidaire washer Strike covering its intended function, typical installation locations and compatibility considerations with various Frigidaire models. The piece will describe common failure symptoms (for example, door not latching, intermittent start faults, or door opening during cycles), stepwise diagnostic checks to isolate strike-related faults versus latch or interlock faults, and practical replacement considerations such as fastening methods, alignment tolerances, and OEM versus aftermarket choices. Safety and testing recommendations for verifying proper operation after service will also be discussed to help technicians, engineers and appliance owners make informed repair decisions.
Table of Contents
- Function and Role of the Washer Door Strike in Cycle Control and Safety Interlocks
- How the 137006900 Frigidaire Washer Strike Operates Within the Door Lock and Control Circuit
- Common Failure Symptoms and Diagnostic Signals Indicative of Strike Malfunction
- Replacement Considerations, Compatible models, and Technician Installation Notes
- Q&A
- In Retrospect
Function and Role of the Washer Door Strike in Cycle Control and Safety Interlocks
The 137006900 Frigidaire Washer Strike functions as the physical engagement point for the door latch and as a discrete safety interlock input to the washer control system. Mechanically, the strike aligns and captures the door latch so the lock assembly can complete a positive engagement; electrically, its actuator operates a microswitch or contact so the control board receives a definitive “door closed/locked” signal before enabling fill, motor drive, or high-speed spin. Proper operation depends on correct geometry and switch orientation – an or else serviceable lock will fail the cycle interlock if the strike is bent,worn,or mounted off-spec,as the control logic is designed to inhibit critical functions until the interlock contact confirms secure closure.
- Primary functions: mechanical capture of the latch and closure of an interlock contact to the control board.
- Common failure symptoms: washer will not start, stalls before spin, door unlocks unexpectedly, or control displays a door/lock error.
- Compatibility considerations: replacement must match mounting tabs, actuator profile, and connector/pinout to ensure the control sees the correct closed/open state.
- Troubleshooting steps: visually inspect alignment, check continuity across the contact with a multimeter, and verify wiring integrity before replacing the strike.
| Item | Description |
|---|---|
| Function | Captures door latch and provides a switch signal confirming door is closed and locked. |
| Electrical behavior | Actuates a microswitch or contact; control logic requires a closed contact (or specific state) to permit motor and valve operation. |
| Mounting considerations | Alignment and connector compatibility determine whether the strike will reliably engage the latch and present the correct electrical state. |
in practical service, replacing the strike is often required only after confirming that the door latch assembly and control wiring are good; technicians should document the exact connector pinout and mounting orientation before swapping parts to avoid introducing intermittent faults. Such as, a multimeter check that shows no change of state when the door is manually latched indicates a failed or misaligned strike contact – replacing the strike with a correctly matched unit and re-torquing mounting hardware typically restores correct cycle control and prevents the control board from entering protective lock-fault states.
How the 137006900 Frigidaire Washer Strike Operates Within the Door Lock and Control circuit
The 137006900 frigidaire Washer Strike is the mechanical latch that secures the door and provides the physical actuation needed by the washer’s door-lock assembly. In practical terms this strike engages the lock mechanism and depresses a microswitch or sensor that the control board reads as a closed interlock; only after that signal does the controller enable the motor drive and water valves. The part’s geometry and mounting determine the point and duration of switch actuation, so correct fit and alignment are required for reliable operation across compatible Frigidaire models.
Within the door lock and control circuit the strike functions as a mechanical interface rather than a power-carrying component: it changes the state of a low-voltage logic input to the PCB by moving a switch or reed sensor into the closed position. Common failure modes include broken or worn latch teeth,plastic deformation that prevents full engagement,or a detached actuator that fails to operate the switch; any of these will leave the control seeing the door as open and will inhibit cycle start. Technicians can verify operation with a multimeter by checking continuity across the lock switch while manually operating the strike,inspecting connector pinouts for corrosion,and confirming mechanical travel and clearance during door closure.
- Symptoms: washer won’t start,door unlocks mid-cycle,or control shows a door-lock error code.
- Swift checks: verify continuity when strike is engaged, inspect striker alignment, and test for free mechanical travel.
| item | Description |
|---|---|
| Function | Mechanically latches door and actuates the door-lock microswitch input to the control board |
| Typical connector | Low-voltage switch wiring or simple two/three-pin connector (model-dependent) |
| Common failure | Broken latch, worn actuator, or misalignment preventing switch closure |
Common Failure symptoms and Diagnostic Signals Indicative of Strike Malfunction
The 137006900 Frigidaire Washer Strike is the mechanical engagement component on the washer door that provides both the physical latch and the electrical “door closed” condition the control board requires to energize a cycle. In practice the strike must align precisely with the door catch so that a micro switch or contact inside the strike closes when the door is fully seated; if the strike is weakened, bent, or its contact surfaces are corroded, the control board may never receive a stable closed signal even though the door appears shut. This part is commonly replaced on frigidaire models where the latch geometry or contact integrity has degraded; confirm model compatibility before replacement because slight differences in mounting tabs and actuator positions can prevent proper engagement or stress other door components.
Technicians diagnosing strike failures should look for both mechanical and electrical indicators: mechanical symptoms include excessive play, visible wear on the striker tab, or misalignment that allows the door to rock free during spin; electrical symptoms include no continuity or intermittent continuity across the strike contacts when the door is latched. A practical bench test is to fasten the strike in a vise, actuate the latch manually, and measure continuity with a multimeter while repeating the action to reveal intermittent contacts. If the control board is reporting door-locked faults but the strike tests good, verify the harness and door catch alignment next; conversely, a consistently open circuit or visible damage on the strike is a valid ground for replacement rather than replacing the board.
- Washer will not start and displays a door-lock error
- Door pops open during cycle or will not stay latched
- Audible clicking of the latch without circuit completion (intermittent contact)
- Visible wear, bent striker tab, or fractured plastic on the strike assembly
- Intermittent operation that clears when pressing the door/latch manually
| Item | Description |
|---|---|
| Function | Provides mechanical engagement and completes an electrical closed-circuit signal to the washer control. |
| Diagnostic signal | No continuity when latched, intermittent continuity, or control-board door-lock fault codes. |
| common corrective action | Inspect alignment and mounting, bench-test continuity while actuating, replace strike if contacts are open, corroded, or mechanically damaged. |
Replacement Considerations, Compatible Models, and Technician Installation Notes
The 137006900 Frigidaire washer Strike is a mechanical latch striker that provides the physical engagement point for the washer lid or door latch assembly; when fully intact and aligned it allows the lid-switch or lock mechanism to detect a closed door and permit the control to initiate cycles. Functionally the strike does not contain active electronics but must present the correct geometry to the lid switch or lock actuator – worn, cracked, or shifted strikes produce symptoms such as the washer failing to start, pausing mid-cycle, or spinning intermittently. such as, a top-load Frigidaire that refuses to enter spin may have a deformed striker that no longer depresses the lid microswitch, so verifying the striker profile and travel against the switch plunger is a quick diagnostic step before replacing other components.
Compatibility for the 137006900 Frigidaire Washer Strike is steadfast primarily by mounting spacing, tab orientation, and thickness rather than by electrical connector type, so technicians should confirm hole-to-hole distances and the striker’s engagement face when cross-referencing models. Installation notes: disconnect mains power and remove the access panels to confirm striker alignment and fastener condition; replace using the original screw pattern,avoid over-torquing plastic bosses,and verify full actuation of the lid switch across the lid’s range of motion before reassembly. Practical checks useful on the bench include measuring actuation travel, comparing the new striker to the old part for dimensional fit, and performing a continuity check on the lid switch while manually operating the striker to ensure consistent contact.
- Confirm part fit: match mounting hole spacing and tab profile to the chassis.
- Inspect for plastic fatigue or fractured bosses that would require housing repair.
- Verify lid switch actuation with the new striker before final reassembly.
- Use original fasteners and moderate torque to avoid stripping plastic threads.
| Item | Description |
|---|---|
| Part | 137006900 Frigidaire washer Strike |
| Function | Mechanical engagement point for lid/door latch; actuates lid switch or lock |
| Key checks | Mounting hole spacing, striker face geometry, actuation travel |
Q&A
What is part number 137006900 for a Frigidaire washer?
Part 137006900 is the door strike (also called the latch striker) used on certain Frigidaire washers. It is the stationary piece mounted on the cabinet or door frame that the door latch engages with to hold the washer door closed during a cycle.
what symptoms indicate the strike (137006900) is faulty?
Common symptoms include the door not latching or staying closed, the washer failing to start or throwing a door-lock error, the door popping open during a cycle, visible cracks or broken plastic on the strike, or noisy engagement between the latch and strike. If the door latch cannot catch the strike reliably, the strike is likely worn or broken.
How do I verify 137006900 is the correct replacement for my washer?
Confirm compatibility by checking your washer’s exact model number (usually on a tag inside the door or on the back) and looking up the parts list in the owner’s manual or on the manufacturer/parts-supplier website. Do not rely on visuals alone-use the model number to ensure 137006900 appears in the parts list for your specific model.
Is the strike an electrical part and can it be tested with a multimeter?
The strike itself is typically a mechanical/plastic part and does not contain electrical components, so it cannot be tested for electrical continuity. If your model has a separate door lock or switch (electrical), that component can be tested; though, the strike is inspected visually for cracks, wear, or deformation and checked for proper alignment with the latch.
How do I replace the 137006900 strike – can I do it myself?
Replacement is often a moderate DIY task. General steps: unplug the washer, open the door, remove the screws or fasteners holding the strike to the cabinet or door frame (you may need to remove a trim/bezel on some models), remove the old strike, fit the new strike in place, and reinstall fasteners. Tools typically needed: screwdriver or nut driver (and possibly Torx bits). Always follow model-specific instructions from the service manual and disconnect power before starting.
Do I need to adjust or align anything after installing the new strike?
Yes-after installing the new strike ensure the door latch engages smoothly and the door closes fully without forcing. If the door does not latch, you may need to slightly reposition the strike (loosen fasteners and shift position) or check the door hinge alignment. Proper alignment is important to avoid stress on the latch and premature wear.
Can a strike be repaired instead of replaced?
Because strikes are typically molded plastic, repair is usually not durable. Minor burrs or debris can be cleaned or smoothed with fine sandpaper, but cracks, missing pieces, or severe wear mean the part should be replaced. Replacement is inexpensive and more reliable than a temporary repair.
Where should I buy a replacement 137006900 and are OEM parts recommended?
Buy from authorized Frigidaire parts dealers, major appliance parts retailers, or the manufacturer’s website to ensure you get an OEM part. Aftermarket options exist and might potentially be cheaper, but OEM parts are recommended for fit, durability, and correct alignment. Verify the seller’s return policy and compatibility with your washer model before purchase.
In Retrospect
The 137006900 Frigidaire washer strike is a small but essential component that helps secure the appliance door or lid and maintain the washer’s safety and operational integrity. By ensuring the door engages correctly with the latch assembly and interlock systems, the strike contributes to proper cycle initiation, prevents inadvertent opening during operation, and supports the washer’s overall performance and user safety.
Accurate diagnosis of door or latch issues is important before deciding on replacement.Symptoms such as failure to start, intermittent door lock faults, or visible wear and misalignment can indicate a faulty strike, but similar symptoms may also arise from latch mechanisms, switches, or control electronics. Verifying the root cause-through visual inspection, functional testing, and reference to service documentation-reduces needless parts replacement and helps restore reliable operation more efficiently.
When replacement is warranted, using the correct part and following recommended installation procedures preserves safety and functionality. Whether performed by a qualified technician or a learned DIYer, proper alignment, secure mounting, and post-repair testing ensure the strike performs as intended. Attention to correct diagnosis and careful replacement helps extend the appliance’s service life while maintaining user safety and consistent washing performance.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
The Blincoo Elite 48" Heavy Duty Dog Rope Toy is made for large breeds that love tug-of-war, chewing, and active play. Strong, simple, and fun for powerful dogs.
Shop on TikTok