241505301 Frigidaire Refrigerator Door Shelf Bin (2 Liter) is a model-specific interior storage component used in Frigidaire refrigerators; it is indeed a shallow, injection-molded shelf bin designed to mount into the door liner and provide approximately two liters of usable storage volume for bottles, jars and other small items. The bin is typically manufactured from a thermoplastic such as ABS or polypropylene and incorporates integral mounting tabs or snap features that engage with the door’s molded rails or brackets. As a discrete replaceable part, it is indeed identified by its OEM part number for compatibility with particular Frigidaire door assemblies.
Within the appliance, this door shelf bin serves as a mechanical load-bearing and containment element that interacts directly with the door liner, mounting clips/rails, and indirectly with the door hinge and gasket systems. Proper engagement of its mounting features transfers user-applied loads into the door structure; excessive or asymmetric loading can influence door alignment and gasket compression, with downstream effects on seal integrity and refrigeration efficiency. The bin’s geometry and placement also affect internal organization and can influence air flow patterns in the fresh-food compartment when bins or stored items obstruct ventilation paths.
In the article that follows you will find a technical overview of the bin’s function and typical installation interfaces, guidance on model compatibility and how to verify the correct replacement (including reference to the 241505301 designation), common failure modes and observable symptoms (cracked or broken mounting tabs, deformation, looseness, items falling or interference with door closing), practical troubleshooting checks to isolate mechanical versus fitment issues, and replacement considerations such as confirming OEM fit, material properties, and proper installation procedures to restore correct door function.
Table of contents
- Functional role, mechanical loads, and material specifications of refrigerator door shelf bins
- How the 241505301 Frigidaire Refrigerator Door Shelf Bin (2 Liter) integrates with the door assembly and retention system
- Common failure modes and diagnostic symptoms: cracks, deformation, and retention failure of door shelf bins
- Compatibility, replacement considerations, installation procedure, and diagnostic checklist for door shelf bin service
- Q&A
- In Summary
Functional role, mechanical loads, and material specifications of refrigerator door shelf bins
The 241505301 Frigidaire Refrigerator Door Shelf Bin (2 Liter) is a purpose-designed, door-mounted storage component that provides localized containment for small bottles, jars, and condiments. Functionally, the bin operates as a cantilevered shelf whose loads are transferred from the molded tray through its snap-in retention hooks into the refrigerator door liner; correct seating and undamaged retention clips are essential for predictable behavior. Compatibility is governed by the bin’s retainer geometry and rib pattern-OEM bins like this one are matched to specific Frigidaire door liners, and installing a non‑matching bin or a damaged clip can change load paths, increase stress at hook roots, and lead to premature failure. For practical repair and maintenance, technicians should verify dimensional fit, confirm full engagement of both retention tabs, and avoid substituting with geometrically dissimilar parts without an adapter or bracket solution.
- Capacity: nominal 2 liters; intended for low‑to‑moderate mass items (condiments, small bottles).
- Mounting: snap‑in molded hooks that bear shear and bending loads into the door liner.
- Common failure modes: clip breakage, plastic creep/deformation, and stress cracking at hook roots.
- Service tips: distribute load along the bin, avoid concentrated heavy items, and replace if ribs or hooks show cracks.
| Item | Description |
|---|---|
| Material (typical) | Injection‑molded thermoplastic (ABS, SAN, or PC blends) with integral ribs for stiffness |
| Mounting interface | Snap-fit retention hooks sized to match Frigidaire door liner pockets |
| Typical static load range | Approximately 2-4 kg distributed (depends on condition of clips and liner reinforcement) |
| Failure indicators | Visible cracks at hooks, permanent deformation, loose fit or excessive play |
Mechanically, the bin is designed to resist bending and shear within the elastic limits of its polymer; the molded ribs increase moment of inertia to lower deflection under typical loads, while the hooks act as localized stress concentrators. Temperature cycling inside the refrigerator and repeated door actuation produce low‑cycle fatigue and long‑term creep in thermoplastics, so practice requires periodic inspection-check clip engagement and tab condition-and removal of heavy glass bottles to reduce cantilever moments. In field replacement, measure hook spacing and overall depth to ensure functional interchangeability, and when evaluating a failed bin inspect both the bin and the door liner pockets, since a damaged liner can mimic bin failure by preventing full engagement or by redistributing loads to unintended areas.
How the 241505301 Frigidaire Refrigerator Door Shelf Bin (2 Liter) integrates with the door assembly and retention system
The 241505301 Frigidaire Refrigerator door Shelf Bin (2 Liter) attaches to the door inner shell through a combination of molded mounting tabs and a support lip that engages a horizontal shelf rail. The bin is molded to locate against predefined bosses in the door cavity so vertical and lateral loads transfer into the door structure rather than the thin bin walls. A snap-fit retention clip or undercut lip fixes the top edge under the door rail, providing positive retention that resists the torsional moment created by loaded items (for example, tall condiment bottles or jars). Proper integration requires the bin’s mounting geometry to match the door’s bosses and rail profile; mismatched geometry will allow movement, concentrate stress at the hooks, and can produce premature cracking at the mounting feet.
- Mounting tabs – engage door bosses and bear shear loads.
- Support lip/rail engagement - transfers vertical load to the door frame.
- Snap-fit retention clip – prevents forward rotation and dislodgement during door movement.
- Load distribution – keep heavy items low and centered to reduce moment on mounting points.
In service, inspect the interface points for hairline cracks, elongated slot wear, or missing retention clips; these are the primary failure modes that compromise fit. To verify correct installation, align the lower edge into the door channel, rotate the bin up until the top lip seats under the rail and listen for a distinct click from the retention feature – absence of this engagement indicates worn or mismatched parts. Technicians replacing this part should confirm door shell boss condition, check for interference with adjacent shelves or the door gasket, and advise users to avoid concentrated point loads at a single tab to extend service life.
| Item | Description |
|---|---|
| Capacity | Approximately 2 liters; practical storage for bottles, jars, and small containers |
| Mounting method | Molded tabs and under-rail snap-fit engagement matching door inner shell geometry |
| material | High-strength thermoplastic (molded) designed for elastic snap engagement |
| typical failure points | Cracked mounting tabs, elongated boss slots, or broken retention clips from overload or impact |
Common failure modes and diagnostic symptoms: cracks, deformation, and retention failure of door shelf bins
The 241505301 Frigidaire Refrigerator Door Shelf Bin (2 Liter) is a molded door-mounted storage tray engineered to hold bottles and small containers on compatible Frigidaire refrigerator doors. It locates and retains loads using molded snap-fit tabs or hooks that engage matching bosses on the door inner liner; variations in tab spacing, boss geometry, and liner curvature determine compatibility across models. In normal operation the bin transmits vertical and lateral loads into the door liner, so stress concentrates at tab roots and at sharp corner radii of the bin body-areas that are most susceptible to crack initiation, creep, and deformation over the service life of the appliance.
Typical failure modes include cracking (frequently enough originating at tab roots or corners), plastic deformation (permanent sag or warpage from sustained loads or heat), and retention failure (broken or worn mounting tabs that allow the bin to disengage). Diagnostic symptoms to look for are visible hairline cracks or stress whitening, loss of preload at the mounting interface (bin moves or tilts under light load), audible rattles when the door closes, and an inability to re-seat the bin securely. Practical checks for technicians: visually inspect tab roots and corner radii under bright light, perform a manual load test with a known-weight bottle to observe sag or detachment, compare fit against an undamaged bin or replacement to confirm liner damage, and examine mating bosses on the door for wear or fracture. If tabs are fractured or the bin shows irreversible deformation, replacement is the recommended corrective action; reuse of a deformed bin risks further damage to the door liner or stored items.
- Visible cracks or stress whitening at tab roots or corners
- Permanent sagging or warped profile under normal load
- Loose fit or bins that pop out during door movement
- Rattling or scraping noises when the door closes
| Item | Description |
|---|---|
| Typical material | Thermoplastic (commonly polypropylene or ABS, depending on model) with molded snap-fit features |
| Common causes | Impact, sustained overload (creep), thermal cycling/embrittlement, and repetitive stress at tab roots |
| Diagnostic checks | Bright-light visual inspection, manual flex/load test, fit comparison to a known-good bin, inspect door bosses |
Compatibility, replacement considerations, installation procedure, and diagnostic checklist for door shelf bin service
The 241505301 frigidaire Refrigerator Door Shelf Bin (2 Liter) is a molded door-mounted storage component designed to retain bottles and small containers while transferring loads into the refrigerator door liner via molded mounting bosses and retention tabs. Functionally it serves as a cantilevered shelf: the lower lip and side guides restrain vertical load while the rear mounting bosses and upper retention features carry shear and tensile forces into the door. Replacement considerations include verifying that the door liner’s mounting bosses are intact, confirming that the replacement bin’s tab geometry matches the OEM engagement points, and inspecting for material fatigue or creep where repeated loading or impact has concentrated stresses. Technicians should compare the part number and physical tab spacing to the appliance parts diagram rather than assuming universal fit across different Frigidaire door designs.
Installation is a simple mechanical swap when the mounting features are undamaged: remove stored items, disengage the lower lip by lifting the bin slightly and pulling away from the door, then compress or depress the upper retention tabs to free the bin; reverse the sequence to install the new unit, aligning tabs into the liner bosses and seating until engagement is confirmed. After installation check for lateral play, proper alignment with adjacent door shelves, and load behavior by placing a representative 2 L bottle and a heavier sample (for example a filled milk carton) to confirm that loads transfer without excessive deflection. Use the following checklist to diagnose common failures and consult the reference table for quick technical details before ordering a replacement.
- Visible cracks or fractures at mounting tabs or along the lower lip
- Excessive lateral or vertical play when seated indicating worn/missing retention features
- Door liner mounting boss damage or missing plastic bosses preventing secure engagement
- Warping or deformation of the bin that prevents a flush seal against the door
- Audible clicks or improper seating during installation indicating mismatched tab geometry
| Item | Description |
|---|---|
| Part number | 241505301 – OEM 2 L door shelf bin for compatible Frigidaire models; verify against model parts list |
| Material | High-impact thermoplastic (clear or translucent), designed for repeated load and low-temperature exposure |
| Fit note | Direct replacement only where door liner boss spacing and tab geometry match; not interchangeable with bins using different retention systems |
Q&A
What is part number 241505301 and what does “2 Liter” mean?
Part number 241505301 is the Frigidaire OEM replacement door shelf bin often listed as a “2 Liter” bin. The “2 Liter” designation refers to the bin’s approximate internal capacity class, not a guarantee it will hold a standard 2.0 L soda bottle upright. Always check the bin shape and measurements against your refrigerator door layout if you need to store tall bottles.
Which Frigidaire models is this door shelf bin compatible with?
241505301 is used on a range of Frigidaire/Frigidaire Gallery/Some Kenmore models.Compatibility varies by model and production year, so confirm fit by checking your refrigerator model number against Frigidaire’s parts lookup or the appliance’s exploded parts diagram.Do not rely on refrigerator series names alone.
How do I remove and install the door shelf bin?
To remove: clear contents, lift the front of the bin slightly, then pull outward to unhook the mounting tabs from the door liner. If mounted on rails, lift up and slide out. To install: align the rear mounting tabs or rails with the slots in the door liner, engage the rear first, then press the front down until it snaps into place. Avoid forcing broken tabs-inspect for damaged clips first.
My bin’s mounting tabs are broken. Can I replace only the tabs or do I need the whole bin?
Frequently enough the tabs are molded into the bin and cannot be replaced separately; technicians typically replace the entire bin. In certain specific cases the door has separate clip hardware that can be ordered, so check the parts diagram for your exact model. Temporary fixes (epoxy, zip-ties) are possible but not recommended for long-term use since they may fail or interfere with door sealing.
What material is this bin made of and is it dishwasher safe?
The bin is made from clear rigid plastic (commonly ABS or polystyrene/acrylic blends). Manufacturer guidance varies; to avoid warping or clouding, hand wash with mild soap and warm water. Avoid high-heat cycles in the dishwasher unless the manufacturer explicitly lists the part as dishwasher-safe.
How can I tell if the bin needs replacing rather than just cleaning?
Replace the bin if you see cracks, broken or deformed mounting tabs, severe crazing that weakens the plastic, or if it no longer secures in the door and items fall out. Discoloration alone doesn’t require replacement unless it compromises strength or hygiene.
Will a generic or aftermarket bin work instead of the OEM 241505301?
An aftermarket or universal bin may fit physically but may differ in mounting tab locations, depth, or material quality. For best fit and longevity, use the OEM part 241505301 or a verified aftermarket part explicitly listed as compatible with your refrigerator model.
Where can I buy a genuine 241505301 replacement and how do I verify it’s correct?
Buy from Frigidaire-authorized parts dealers, the manufacturer’s parts website, or reputable appliance-parts retailers. Verify correctness by matching the part number and checking compatibility with your refrigerator model number. If available,consult the appliance’s parts diagram to confirm the bin shape and mounting method before purchasing.
In Summary
The 241505301 Frigidaire Refrigerator Door Shelf Bin (2 Liter) serves a straightforward but important role in everyday refrigerator use: it provides a dedicated,compact storage location on the door for bottles,condiments and other small items,helping to organize contents for accessibility and reducing clutter on interior shelves. As an OEM-designed component, its shape, mounting points and capacity are engineered to match specific Frigidaire door assemblies so that items are held securely and the door closes and functions as intended.
Proper diagnosis is critically important when a door shelf bin shows signs of wear or failure. Visible cracks, broken or worn mounting tabs, distortion, persistent odors, or a loose fit that allows stored items to shift are indications that the bin may no longer be performing safely or effectively. Identifying whether the issue is limited to the bin itself or related to the door assembly or mounting hardware ensures the correct corrective action is taken and prevents unnecessary or incomplete repairs.
timely replacement with the correct 241505301 part restores intended storage capacity, maintains safe and hygienic food storage, and helps preserve the refrigerator’s fit and function. When replacement is needed, selecting the compatible part and following recommended installation or consulting a qualified technician minimizes the risk of further damage and extends the useful life of the appliance.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
The Blincoo Elite 48" Heavy Duty Dog Rope Toy is made for large breeds that love tug-of-war, chewing, and active play. Strong, simple, and fun for powerful dogs.
Shop on TikTok