241860801 Frigidaire Refrigerator Ice Container Assembly is a molded ice storage and delivery component used wiht automatic ice makers; it functions as the receptacle that collects harvested ice and, where applicable, houses the auger or feed mechanism that delivers ice to a dispenser. The assembly is typically a rigid plastic bin with specific mounting points and interfaces for mechanical couplings, sensors, and sometimes a motor or drive shaft, designed to fit within the freezer compartment of compatible Frigidaire refrigeration units.
Inside the appliance, the ice container assembly interfaces directly with the ice maker harvest cycle and the dispenser subsystem: it receives ice from the ice maker mold during the harvest, provides a controlled passage for ice to travel to the door dispenser or internal chute, and frequently contains sensors or switches that inform the control board about ice level or jam conditions. It thus interacts mechanically with the auger/drive motor, electrically with level or door switches, and environmentally with the freezer’s temperature and defrost systems; any misalignment, crack, or obstruction in the container can impede dispensing, trigger error states, or affect ice production rates.
In this article you will find a technical overview of the part’s function and typical installation environment, guidance on compatibility and identification of the 241860801 assembly, common failure symptoms to watch for (such as ice bridging, structural damage, auger stalls, or sensor faults), practical troubleshooting steps to isolate mechanical versus electrical causes, and considerations for safe and correct replacement-including packaging and connector checks, mounting alignment, and basic post-installation verification procedures. The intent is to provide technicians, engineers, and appliance owners with the essential technical context needed to diagnose issues and make informed repair or replacement decisions without prescriptive marketing language.
Table of Contents
- Function and Operational role of the Ice Container Assembly in Frigidaire Refrigerators
- How the 241860801 Frigidaire Refrigerator ice Container Assembly Interfaces with the Ice Maker, Door, and Evaporator Components
- Common Mechanical and Electrical Failure Symptoms of the Ice Container Assembly
- Replacement Considerations and Step‑by‑Step Installation Procedure for the Ice Container Assembly
- Q&A
- Key Takeaways
function and Operational role of the Ice Container Assembly in Frigidaire Refrigerators
The 241860801 Frigidaire Refrigerator Ice Container Assembly serves as the mechanical and functional interface between the automatic icemaker and the dispenser or auger system. It is a molded bin with guide surfaces, mounting tabs and an integral drive-coupler area that receives ice as it is ejected from the icemaker, retains a working volume of ice, and meters release into the auger or paddle mechanism. In many configurations the container includes features such as a keyed spline or coupler for the auger drive, a discharge ramp to prevent bridging, and simple mechanical or optical flags used by the refrigerator controller to detect low-ice conditions; thes elements determine how the part behaves under normal cycling and how it couples to the dispenser motor and latch assemblies.
- Primary functions: receive ice, prevent bridging, align ice flow to auger/paddle, and provide low-ice detection feedback.
- Common symptoms of failure: ice bridging, noisy or stalled dispenser motor, cracked bin or worn coupler splines, and incorrect low-ice signals to the control board.
- Installation checks: verify seating against the icemaker discharge, confirm spline engagement with the drive coupler, and ensure mounting tabs are intact and not warped.
| Item | Description |
|---|---|
| Material | Molded freezer-grade thermoplastic designed to resist cracking and embrittlement at low temperatures. |
| Interface features | Guide ramps, discharge chute, mounting tabs and a drive-coupler/paddle bore for auger engagement. |
| service notes | Inspect for cracks, deformations, or worn splines; clean frost and debris to restore reliable ice flow. |
Operationally, the ice container affects dispenser load, noise, and reliability: a deformed bin or misaligned coupler increases torque on the auger motor and may trigger motor overloads or intermittent dispensing. Thermal and moisture management is part of the component’s role-minimizing large temperature gradients and exposed wet surfaces reduces frost buildup that causes bridging. For technicians, practical troubleshooting begins with physical inspection (splines, tabs, chute clearance), manual ice removal and controlled defrost to confirm whether the container or upstream icemaker is the root cause; replacement is warranted when cracks, permanent warpage, or damaged splines prevent correct mechanical engagement or create repeat jams.
How the 241860801 Frigidaire Refrigerator Ice Container Assembly interfaces with the Ice Maker, Door, and Evaporator Components
The 241860801 Frigidaire Refrigerator Ice Container Assembly is a molded storage bin that mechanically and electrically interfaces with the ice maker, freezer door, and the evaporator housing to maintain proper ice delivery and control. It seats beneath the ice maker’s discharge chute using molded mounting tabs and alignment ribs that ensure the chute deposits cubes into the bin without misalignment or bridging. A built-in full-bin actuator (mechanical lever or plunger) engages the ice maker’s control circuit to halt production when storage capacity is reached; correct seating of the bin is required for reliable actuation. On models with an internal dispenser or auger, the bin incorporates a coupling interface or clearance zone so the auger motor gear can engage without axial play, and the bin’s outer profile is designed to clear the freezer door gasket and hinge path to avoid interference when the door closes.
Functionally, the assembly also provides thermal and frost-management interfaces with the evaporator and defrost system: its geometry maintains a specified gap from the evaporator cover and heater so warm meltwater drains to the drain channel rather than refreezing inside the bin. Technicians should verify three practical checks when diagnosing related faults: that the bin is fully seated (actuator depressed), the discharge chute-bin alignment is correct (no offset causing jams), and there is adequate evaporator clearance (no damaged shields or excessive ice build-up). Typical symptoms tied to interface faults include continuous ice production despite a full bin (actuator fault or misalignment), ice bridging or clumping (poor chute geometry or defrost failure), and door interference that prevents a full seal (bin not seated or incorrect replacement part).
- Mounting tabs and alignment ribs - ensure accurate chute positioning.
- Full-bin actuator – mechanical switch engagement to stop the ice maker.
- Dispenser/auger coupling or clearance – compatibility with motor drive.
- Evaporator clearance and drainage - prevents refreeze and jams.
| Item | Description |
|---|---|
| Mounting interface | Molded tabs and slots that secure the bin under the ice maker discharge. |
| Full-bin actuator | Mechanical plunger or lever that signals the ice maker control to stop. |
| Dispenser coupling | Axial clearance or gear interface for auger-driven dispensers when present. |
| Evaporator clearance | Designed gap and drain path to prevent frost build-up and water ingress. |
Common Mechanical and Electrical Failure Symptoms of the Ice Container Assembly
The 241860801 Frigidaire Refrigerator Ice Container Assembly is a passive and interface component that receives ice from the icemaker, aligns the ice with the dispenser auger or door chute, and provides mechanical mounting and electrical connections for any associated sensors or actuator couplings. In service the container must maintain correct alignment with the auger coupling, provide unobstructed ice flow, and present reliable connector contacts for the dispenser motor and any level-detection switches. Compatibility concerns are primarily mechanical-tab locations, mounting pin spacing, and auger-coupler fit are common mismatch points-so technicians should verify physical dimensions and connector type when replacing the assembly on a specific Frigidaire model.
Mechanical and electrical faults produce distinct, diagnosable behaviors that narrow the root cause quickly. Examples include grinding or scraping noises caused by a misaligned auger-to-coupler engagement, persistent ice clumping due to poor air sealing or a failed anti-clump heater, and intermittent dispenser operation resulting from a loose wire harness or a failing door switch. Begin troubleshooting by observing the symptom under load (attempt a dispense while listening and watching the auger), inspecting visible mounting tabs and the ice path for obstructions, and measuring voltage at the motor connector to separate mechanical seizure from electrical loss of drive.
- Auger stalls or motor hums with no rotation – possible seized auger, stripped coupler, or jammed ice.
- Intermittent dispense or no response – loose/oxidized connector, broken wire, or defective door/actuator switch.
- Ice clumping or large ice blocks – insufficient airflow, damaged bin insulation, or moisture intrusion.
- Unusual scraping or grinding noises - misaligned mounting, cracked bin walls, or foreign debris.
| Item | Description |
|---|---|
| Ice jam / Stalled auger | Inspect the auger coupler and bin for crushed ice or foreign objects; rotate auger by hand if accessible to check for mechanical binding. |
| Motor hums but no rotation | Measure supply voltage at the motor; if voltage is present, suspect mechanical seizure or stripped drive coupling. |
| Intermittent electrical operation | Check harness continuity, connector pins for corrosion, and the door/actuator switch function under repeated cycles. |
Replacement Considerations and Step‑by‑Step Installation Procedure for the Ice Container Assembly
The 241860801 Frigidaire Refrigerator Ice Container Assembly is the molded receptacle that collects, stores, and presents harvested ice from the icemaker and interfaces with any dispenser or auger drive mechanism. Functionally the assembly must provide accurate alignment with the icemaker chute, secure mounting on the internal rails, and proper engagement of any built-in sensors or mechanical couplings; common failure modes include cracked walls that allow ice spill into the evaporator cavity, worn rail shoulders that permit lateral play, and broken sensor housings that prevent accurate ice level detection. Verify compatibility by matching the service part number and mounting geometry to the refrigerator model; visually confirm the location of the auger boss or sensor connector as some Frigidaire designs use a passive bin while others incorporate an auger drive or optical sensor integrated into the container roof.
Replace the container with the refrigerator de-energized, and follow a methodical installation sequence to avoid drivetrain binding or sensor misalignment. Before installing,clear ice and defrost any frost bridges,inspect the icemaker chute and rail tracks for burrs or obstructions,and transfer any mounting hardware or gaskets from the old bin if required. After seating the new container on its rails and engaging any retention tabs, verify free rotation of the auger (if present) and secure electrical connectors with full engagement; perform a manual harvest or dispenser cycle to confirm correct behavior and listen for rubbing or grinding that indicates misalignment.
- disconnect power and remove ice: empty bin and isolate refrigerator power.
- Remove old container: disengage retention tabs and slide out along rails; note orientation of any sensors or auger drive.
- Inspect and clean: clear ice bridges, remove debris from tracks, inspect rails and support bosses for damage.
- Install new container: align rails, slide into position until retention tabs engage, connect any sensor or motor connectors.
- Functional check: restore power,run an icemaker harvest or dispense cycle,verify unobstructed auger rotation and correct ice flow.
- Troubleshoot common issues: if binding occurs, lift slightly and re-seat; if sensor doesn’t register, reseat connector and check continuity per service manual.
| Item | Description |
|---|---|
| Compatible Models | Match refrigerator model code and rail geometry; not all Frigidaire bins are interchangeable between side-by-side and French-door units. |
| mounting Features | molded rails,retention tabs,optional auger boss and sensor connector-verify physical fit before final installation. |
| Tools / Checks | Phillips or nut driver for fasteners, flashlight for visual inspection, verify connector seating and free auger rotation. |
Q&A
What is part 241860801 (Frigidaire ice container assembly) and what does it do?
241860801 is the ice container (ice bin/assembly) that collects and stores ice produced by the refrigerator’s ice maker. Depending on the refrigerator model the assembly may include the bin, chute/door interface and mounting features that allow the dispenser or auger to access the ice. It does not usually contain the ice maker motor or water valve – those are separate components.
How do I know if 241860801 is compatible with my refrigerator?
Compatibility depends on your refrigerator model number. Check the fridge model (usually on a label inside the fresh food compartment or behind the grille) and compare it to the part listing on Frigidaire’s parts website or with an authorized parts dealer. Do not rely solely on visual similarity – cross-reference your model number to confirm fit and function.
What are the safe steps to remove and install the ice container assembly?
General steps: 1) Unplug the refrigerator or turn off the ice maker/power for safety. 2) Empty and remove any loose ice from the bin. 3) Open the freezer/access panel and locate the bin mounting or retainer clips. 4) Release any clips or remove screws holding the bin (some bins simply slide out). 5) If there are electrical connectors (sensors or lights), disconnect them carefully. 6) Install the new bin by reversing removal: connect any plugs, seat the bin fully, secure clips/screws. 7) Restore power, run a test/harvest cycle if available and discard the first few trays of ice. Note: specific fasteners and clip locations vary by model, so refer to your model’s service sheet or owner’s manual when available.
What tools do I need to replace the ice container assembly?
Common tools: a phillips or flat screwdriver, nut driver set (for small screws/bolts), work gloves to protect hands and keep ice clean, and a towel to catch water from melting ice.You might also need a putty knife or plastic pry tool for clips on some models. In many cases no special tools are required because the bin snaps in and out.
My ice container is cracked or leaking - can it be repaired or should I replace it?
Small cosmetic cracks that don’t affect sealing can sometimes be temporarily patched with a food-safe silicone sealant, but this is a short-term fix. Cracks that allow melted water to leak, interfere with dispenser operation, or compromise structural integrity should be replaced. Replacement is the reliable long-term solution and preserves hygiene and fitment.
Why is ice clumping or caking in the bin after installing a new container?
Ice caking usually results from one or more of: freezer temperature too warm or fluctuating, high humidity in the freezer, frequent door openings, old/partially melted and refrozen ice, or a misaligned bin that interferes with ice flow. Fixes: set the freezer to the recommended temperature, discard old ice, ensure the bin is seated correctly, minimize door openings, and verify the ice maker is operating normally (no water leaks or partial fills that create slushy ice).
The dispenser/auger won’t dispense ice after I replaced the bin. What should I check?
First confirm the bin is fully seated and any actuator or dispenser interface is aligned – many dispensers need the bin properly positioned to engage the auger. Check for ice jams or large clumps blocking the auger. Verify the ice maker and dispenser have power and the dispenser switch/door actuator functions. If the auger motor runs but no ice moves, the bin may be empty or the auger coupling is damaged. If in doubt, run the refrigerator’s diagnostics or consult a technician.
How should I clean and maintain the ice container to prevent problems?
Routine maintainance: remove the ice and wash the bin with warm water and mild dish soap,rinse thoroughly and dry before reinstalling. Avoid harsh or abrasive cleaners and do not use strong bleach solutions unless diluted to a manufacturer-recommended concentration. Periodically discard old ice (especially after power outages), keep the freezer door seals in good condition, and maintain recommended freezer temperatures. If you’re switching to a replacement bin, sanitize the bin before first use and discard the first few batches of ice after installation.
Key Takeaways
The 241860801 Frigidaire Refrigerator Ice Container Assembly serves as the primary storage and delivery component for produced ice, maintaining hygienic containment, proper alignment with the freezer’s dispensing mechanism, and contributing to consistent ice production and flow. As a purpose-designed part for compatible Frigidaire models, its correct fit and condition help prevent ice bridging, leaks, and operational interruptions that can affect overall appliance performance.
Accurate diagnosis of issues related to the ice container-such as visible cracks or warping, improper seating, odors, ice buildup, or interaction problems with sensors and dispensers-is essential before deciding on repair or replacement. A systematic inspection, reference to model specifications, and, when appropriate, professional troubleshooting will distinguish between remedial cleaning or adjustment and the need for component replacement, reducing the risk of unnecessary expense or recurring failures.
When replacement is warranted,installing a properly specified 241860801 assembly restores intended function,supports food safety by preventing contamination,and can extend the service life of the refrigerator by eliminating recurring faults. Whether performed by a qualified technician or a knowledgeable owner following manufacturer guidance, timely and correct replacement is a practical step to maintain reliability and performance in the long term.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
The Blincoo Elite 48" Heavy Duty Dog Rope Toy is made for large breeds that love tug-of-war, chewing, and active play. Strong, simple, and fun for powerful dogs.
Shop on TikTok