316112005 Frigidaire Oven Range Anti Tip Bracket Kit is a mechanical safety mounting assembly designed to anchor a freestanding oven or range to the surrounding structure to prevent unintended tipping.The kit typically consists of a metal bracket and the required fasteners and is intended to be secured to the floor, wall stud, or cabinet structure and to interface with the range chassis or rear leveling foot. As a purpose-built component, it is indeed a non-powered, load-bearing part that completes the range’s stability system during normal use and when the oven door is open.
within the appliance, the anti-tip bracket provides a fixed structural connection point that takes shear and moment loads away from the range’s cabinet and transfers them into the building structure. It interacts directly with the range mounting points and indirectly with the leveling system; proper performance requires that the bracket location, fastener type, and range leveling be coordinated so that forces are distributed correctly. The bracket does not affect the range’s electrical or gas systems, but it is integral to safe operation because it prevents forward rotation of the appliance when weight is applied to an open door or when the unit is pushed.
In this article readers will find a clear explanation of the kit’s functional purpose,guidance on model compatibility and how to verify the 316112005 part for specific Frigidaire range models,common failure symptoms (such as loose or missing fasteners,damaged bracket,or excessive range movement),and practical troubleshooting checks a technician or owner can perform. Replacement considerations such as selecting appropriate anchors for the mounting substrate, confirming part number fitment, and avoiding common installation errors will also be covered so that repairs restore the intended mechanical load path and compliance with the manufacturer’s installation requirements.
Table of contents
- Function and Role of the Anti‑Tip Bracket assembly in Oven Stability and Operator Safety
- How the 316112005 Frigidaire Oven Range Anti Tip Bracket Kit Integrates with Range Chassis, Floor Anchoring, and load Transfer
- Common Failure Symptoms, Wear Modes, and Inspection Criteria for Anti‑Tip Brackets
- Compatibility, Model Fitment, Replacement Considerations, Installation Procedures and Troubleshooting Diagnostics
- Q&A
- Insights and Conclusions
Function and Role of the Anti‑tip Bracket Assembly in Oven Stability and Operator Safety
The 316112005 Frigidaire Oven range Anti Tip Bracket Kit is a simple mechanical assembly that prevents the oven from rotating forward when weight is applied to an open door or when a user inadvertently leans on the door. the bracket is fastened to the building structure (wall stud or floor) and provides a positive stop for the range’s rear leveling leg or a mating tab; under a tipping load the overturning moment is transferred through the bracket into the structure rather than through the appliance frame. In practice this means the bracket is designed to absorb shear and bending loads and to maintain a defined engagement position so the range does not pivot off its feet under normal use.
Functionally the anti‑tip behaves as a fixed anchor point: it must be located so the range can be pulled forward slightly and the bracket will engage the range’s rear foot without allowing additional forward travel. Compatibility is primarily persistent by the rear leg/foot geometry and the distance from the rear cabinet to the building surface, so installers verify fitment and use appropriate fasteners (wood screws into studs, masonry anchors for concrete). Typical service checks include confirming the bracket is not deformed, fasteners remain tight, and the engagement clears by the specified gap; replace the bracket or anchors if bent, corroded, or if the range shifts when pulled.Practical installation examples: secure to a 2×4 wall stud with a #12 wood screw and washer for drywall installations, or use a concrete anchor when the bracket must be mounted to a masonry surface in an island or retrofit situation.
- primary role: transfer tipping moment to building structure via bracket-to-leg engagement
- Mounting options: wood stud, metal stud with rated anchors, masonry anchors
- Inspection cues: visual deformation, loose fasteners, movement when range is pulled
- Replacement triggers: missing bracket, stripped anchors, or altered rear leg geometry
| Item | Description |
|---|---|
| Part Number | 316112005 - anti‑tip bracket assembly for select Frigidaire ranges |
| Material | Stamped steel, typically painted or zinc-plated to resist corrosion |
| Mounting | designed for attachment to wall studs or masonry with appropriate fasteners |
| Typical symptom | Range moves or tilts forward when the top oven door is opened or when load is applied |
How the 316112005 Frigidaire Oven range Anti Tip Bracket Kit Integrates with Range Chassis, Floor Anchoring, and Load Transfer
The 316112005 Frigidaire Oven Range Anti Tip Bracket Kit provides a direct mechanical interface between the range chassis and the building substrate to prevent forward rotation of the appliance. The kit typically fastens to the floor or subfloor and is positioned to capture or block the range’s rear leveling leg or a small chassis lip; when the range is leveled into place the leg engages the bracket so the chassis cannot pivot forward. This bracket is a simple steel component but its correct function depends on precise positioning relative to the chassis engagement point and on using the appropriate fastener for the substrate so that the bracket cannot pull out under load.
The behavior under load is best described as a controlled transfer of tipping moment into reaction forces in the fasteners and substrate: a forward moment (for example, when the oven door is opened with items on it or when weight is applied to the open door) produces a shear and tensile demand on the bracket assembly that is routed into the floor. Installers must select anchors rated for the expected shear and pull-out loads and verify that the bracket captures the rear leveling leg or chassis member with minimal clearance. Practical considerations include using wood screws into solid joists or a block beneath a plywood subfloor, and using sleeve or wedge anchors for concrete; if the leveling legs are extended beyond the bracket position, the leg should be adjusted so engagement is positive. Common service checks are to confirm the rear engagement point is present, ensure fasteners are tight, and verify that the bracket is aligned with the chassis so the load path goes directly into the substrate.
- Positive mechanical engagement with the rear leveling leg or chassis
- Transfers tipping moment into fastener shear/tension and substrate reaction
- Requires substrate-appropriate anchors (wood, plywood-over-joist, concrete)
- Compatibility depends on chassis clearance and leveling-leg position
| item | description |
|---|---|
| Bracket | Steel capture/block mounted to floor that receives the range’s rear leveling leg or chassis lip |
| Fasteners | Wood screws, lag screws, or masonry anchors chosen by substrate to resist shear and pull-out |
| Engagement point | Rear leveling leg or chassis member that must seat into the bracket with minimal play |
| Load path | Range chassis → bracket capture → fasteners → building substrate (joist, subfloor, or concrete) |
Common Failure Symptoms, Wear Modes, and Inspection Criteria for Anti‑Tip Brackets
The 316112005 Frigidaire Oven Range Anti Tip Bracket Kit functions as a mechanical stop that restrains the range chassis from rotating forward when a load is applied to the open oven door or the cooktop. The bracket fastens to the floor or wall and engages a dedicated mounting boss on the range rear frame; compatibility depends on the chassis mounting pattern, leg/caster configuration, and substrate used for anchoring (wood subfloor, concrete, or masonry require different fasteners). In normal behavior the bracket should not carry continuous load but must arrest sudden forward moments generated by people leaning on the oven door, sliding heavy cookware, or by impeding motion during appliance repositioning. Technicians should verify that the bracket aligns with the chassis stop, that the chosen anchor type matches the substrate, and that any supplied fasteners seat flush without distortion.
Common failure symptoms,wear modes,and inspection criteria focus on loss of clamp-up,metal fracture,and fastener compromise. Typical wear modes include plastic deformation of the bracket tab, fatigue cracking at bend radii or welds, corrosion thinning at contact surfaces, shear failures of screws, and elongation of mounting holes from repeated loading. A practical inspection routine consists of a visual check for cracks, bends, and corrosion, a manual verification that the bracket engages under a forward load (open the door and apply a controlled forward force while observing movement), and confirmation that anchors and threads are not stripped or loose; if the bracket shifts or the range translates more than a few millimeters under a single applied load or shows progressive movement after repeated loading, replacement is warranted.
- Symptoms: forward rocking or tipping when oven door is open, visible gap between bracket and chassis stop, loose or rounded fastener heads.
- Wear modes: bending at the engagement tab, fatigue cracks at welds or bends, corrosion and section loss near contact points.
- Inspection criteria: no visible cracks, secure anchors appropriate to substrate, no elongation of mounting holes, and zero play at the engagement point under load.
| Item | Description |
|---|---|
| Corroded bracket | Reduced section and potential brittle fracture; replace if pitting or through‑metal loss is evident. |
| Bent or misaligned tab | Prevents full engagement with chassis stop; realignment or replacement required to restore function. |
| Elongated/stripped hole | Allows slippage under load; repair by replacing bracket or installing properly sized anchor into undamaged substrate. |
Compatibility, Model Fitment, replacement Considerations, Installation Procedures and Troubleshooting Diagnostics
316112005 Frigidaire Oven Range Anti Tip Bracket Kit is a stamped-steel retention assembly that secures the range chassis to the floor or cabinet substructure to prevent forward tipping when the door is loaded. The bracket uses slotted mounting holes to permit fore/aft adjustment and is intended to engage the range rear crossmember or designated chassis attachment point; fitment depends on the model family, presence of rear trim plates, and cabinet floor thickness. Technicians should confirm compatibility by measuring the distance from the chassis attachment point to the finished floor, matching that dimension to the range service literature, and verifying that leveling legs, trim, or wiring harnesses do not obstruct bracket placement.
Replacement and installation involve pulling the range clear of the enclosure, aligning the bracket so the slots match the chassis holes, and installing the correct grade and length fasteners without distorting the frame. Common failure modes and diagnostics include loose or missing fasteners, a bent bracket after impact or overload, and perceptible rocking or forward movement when the door is opened with a loaded rack. after installation, torque fasteners to manufacturer values, perform a load test by opening the door with a typical cookware load, and re-check alignment after the range is leveled; if the bracket bears only on drywall or weak substrate, add blocking or use specified anchors to achieve a rigid connection.
- Verify alignment: measure chassis-to-floor distance and compare to service spec before installation.
- inspect fasteners: replace stripped or corroded screws with specified grade fasteners and torque appropriately.
- Substrate check: ensure bracket seats on solid blocking or use anchors rated for appliance loads.
- Functional test: open the door with a typical load and observe for movement or rocking; re-torque if movement occurs.
| Item | Description |
|---|---|
| Material | Stamped steel bracket with slotted holes for adjustment |
| Mounting interface | Engages chassis rear crossmember or cabinet floor; orientation varies by model |
| fasteners | Use manufacturer-specified length and grade; tighten to published torque |
Q&A
What is the 316112005 Frigidaire Oven Range Anti‑Tip Bracket Kit and why is it needed?
the 316112005 kit is an anti‑tip device supplied for Frigidaire ranges/ovens. Its purpose is to anchor the range to the floor or wall so the appliance cannot tip forward if weight is placed on an open oven door or if the range is pushed. Anti‑tip brackets are a safety requirement because range tip‑overs can cause burns, scalds or serious injury, especially to children.
Which Frigidaire models will this anti‑tip bracket fit?
The bracket is intended for Frigidaire slide‑in and freestanding ranges that accept a rear anti‑tip anchoring device. Compatibility varies by model and installation configuration; always check your range owner’s manual or the appliance model/serial number against Frigidaire parts data. If in doubt, contact Frigidaire customer service or a qualified technician to confirm fit before purchase.
what parts come in the kit?
A typical anti‑tip kit includes a metal mounting bracket and the fasteners needed to attach it to the floor or wall (screws/bolts and sometimes wall anchors), plus installation instructions. Contents can vary; verify the included parts list in the packaging before beginning installation and obtain additional hardware if required for your floor type or wall construction.
What tools and materials do I need to install it?
Common tools: screwdriver or drill/driver, masonry or wood drill bits (depending on mounting surface), tape measure, pencil, adjustable wrench, and possibly a stud finder.You may also need different anchors or longer fasteners for thick tile, concrete, or unusual subfloors.always have the range unplugged and gas supply turned off (and disconnected if necessary) before you move it to install the bracket.
How is the anti‑tip bracket installed (overview)?
Installation steps (high level): 1) Pull the range forward and locate the recommended mounting location behind the appliance per the instructions. 2) position the bracket so it will engage the range’s rear leveling leg or rear foot when the range is pushed back.3) Fasten the bracket to the floor or wall using appropriate fasteners for your surface. 4) Slide the range back so the rear leg engages the bracket. 5) Verify engagement and perform the recommended safety test. Always follow the manufacturer’s step‑by‑step instructions included with the kit.
How do I test the anti‑tip bracket to make sure it’s installed correctly?
after installation, slide the range fully back so the rear foot engages the bracket.Open the oven door and apply downward force near the front (or carefully try to tip the unit forward) – the range should not tilt forward more than a small amount and should not lift its rear feet clear of the floor. Do not perform aggressive tests; follow the specific testing method in the kit instructions. If the range moves or tips, recheck bracket placement and fasteners or call a professional.
Do local codes or the manufacturer require professional installation?
Many manufacturers require an anti‑tip device to be installed per the instructions before using the range; local building codes or safety standards may also require proper anchoring. While a competent DIYer can frequently enough install these brackets, professional installation is recommended if you are unsure about mounting into concrete, through tile, locating studs, or handling gas/electrical disconnection and reconnection. Using a licensed technician helps ensure compliance with local codes and safe appliance operation.
What should I do if I move the range or replace flooring-do I need a new bracket?
If you move the range or change the flooring/wall behind it,you must verify the bracket is still securely anchored and re‑engaged with the rear leg. If the original mounting points are no longer suitable (new floor height, damaged bracket, or different clearance), remove and reinstall the bracket in a proper location or replace it. Replace the bracket instantly if it is indeed bent, cracked, or or else damaged. Always reattach and test the anti‑tip device after any work that affects the range position or the mounting surface.
Insights and conclusions
The 316112005 Frigidaire Oven Range Anti Tip Bracket Kit is a purpose-built safety component designed to secure a freestanding oven range and reduce the risk of tipping. Properly installed,the bracket helps stabilize the appliance under normal use and incidental loading,protecting users from burn and crush injuries and reducing the potential for property damage. As an OEM part engineered for Frigidaire ranges, it supports correct fit and function when matched to compatible models.
Accurate diagnosis and timely replacement are key to maintaining this safety function. Identifying worn, damaged, loose, or incorrectly installed brackets through inspection ensures the range remains properly anchored. When replacement is necessary, using the correct 316112005 kit and following manufacturer installation guidance-or engaging a qualified service technician-helps restore designed performance and preserves warranty and safety expectations.
the anti-tip bracket kit is a small but essential safety device. Routine checks, prompt diagnosis of issues, and replacement with the appropriate Frigidaire part when required collectively contribute to safer operation and long-term reliability of the range.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
The Blincoo Elite 48" Heavy Duty Dog Rope Toy is made for large breeds that love tug-of-war, chewing, and active play. Strong, simple, and fun for powerful dogs.
Shop on TikTok