The 241796405 Frigidaire Refrigerator Water Tube Fill is a factory part-numbered water fill tube assembly designed to convey metered potable water within compatible Frigidaire refrigerator models. As a dedicated plumbing component, it typically consists of molded or flexible tubing and end fittings that connect the household water inlet valve to the ice maker fill cup or internal water reservoir, and it is intended to be replaced when damaged, cracked, or improperly routed.
Inside the appliance the water tube serves as the hydraulic link between the water inlet valve,the ice maker fill mechanism and,in some configurations,the dispenser or internal trough. It interfaces with the inlet valve solenoid, the ice maker’s fill valve/port and the cabinet mounting points; proper attachment, routing and sealing are necessary to maintain flow rate, prevent backflow and avoid air pockets. Because the tube is often routed through cold compartments it is also subject to low-temperature effects (kinking, partial freezing) and mineral buildup that can alter fill volume and timing, so its physical condition and connector integrity directly affect ice quality, fill consistency and leak prevention.
This article will provide a technical overview of the 241796405 water tube fill including its functional role, compatible appliance contexts, common failure symptoms (leaks, underfill, overfill, intermittent fills), diagnostic checks and basic troubleshooting steps a technician or owner can perform.It will also cover replacement considerations such as correct connector type and orientation, securing and routing best practices, material compatibility and post-installation verification procedures to ensure reliable operation after service.
Table of Contents
- Function and operational role of the refrigerator water tube fill within the ice and water delivery system
- How the 241796405 Frigidaire Refrigerator Water Tube Fill Works Inside the Appliance
- Common failure symptoms and measurable diagnostic indicators of water tube fill malfunction
- Replacement considerations,model compatibility,and step-by-step installation precautions for the 241796405 water tube fill
- Q&A
- The Conclusion
Function and operational role of the refrigerator water tube fill within the ice and water delivery system
The 241796405 Frigidaire Refrigerator Water Tube Fill is the molded water delivery conduit that routes potable water from the refrigerator’s inlet valve to the ice maker and dispenser. It establishes the precise bore, length, and sealing interfaces required for consistent fill volumes and leak-free operation; the component typically uses a press-fit grommet or barbed connection at the inlet valve and is formed from a food-grade polymer to resist corrosion and mineral buildup. Compatibility depends on matching the tube’s internal diameter, overall length, and fitting style to the refrigerator’s valve and ice-module geometry so flow characteristics remain within design tolerances.
During a fill cycle the inlet valve opens for a controlled interval and the tube’s internal geometry determines flow rate, fill time, and weather the ice mold receives the intended volume.common operational failures include hairline cracks at bends, hardening or deformation of the seating surfaces, and internal scaling that reduces flow; symptoms technicians see are slow or partial fills, continuous filling, or visible leakage near the valve grommet. Practical service checks include visually inspecting the tube for damage, verifying proper insertion into the valve grommet, clearing mineral deposits, and temporarily substituting a known-good tube to confirm restoration of correct fill behaviour before replacing related components.
- Primary role: direct and meter water from inlet valve to ice maker/dispenser.
- Installation note: must match OEM bore, length, and fitting type for correct performance.
- Common symptoms of failure: reduced flow, overfilling, continuous valve operation, and leaks at the grommet.
- Service tip: inspect O-rings/grommets and inlet valve seating when replacing the tube.
| Item | Description |
|---|---|
| part number | 241796405 |
| Function | Routes water from the inlet valve to the ice maker/dispenser; maintains required flow geometry and seals. |
| Material / Fit | Food-grade polymer; barbed or press-fit ends-replace with matching dimensions to ensure compatibility. |
How the 241796405 Frigidaire Refrigerator Water Tube Fill Works Inside the Appliance
The 241796405 Frigidaire Refrigerator Water Tube Fill is a molded water-routing component that directs cold water from the inlet valve to the dispenser and icemaker assemblies inside compatible Frigidaire refrigerators.Its primary function is passive: provide a sealed, kink-free pathway sized to maintain designed flow rates and to align with factory mounting points and seals. The tube does not regulate pressure – that role belongs to the refrigerator’s water inlet valve and pressure-reducing devices upstream - so proper performance depends on correct seating at barbed or clipped connections, intact O‑rings or clamps, and unobstructed internal diameter.
Compatibility is determined by connector geometry and mounting tabs rather than by length alone; replacement must match the factory routing so the tube does not contact moving parts or heat sources.Technicians diagnosing low flow or intermittent dispensing should inspect the 241796405 tube for cracks, pinches, ice formation, sediment blockages, and secure attachment at the inlet valve and dispenser ports. When replacing, verify that the replacement tube reproduces the same connection type and mounting features, and test the system at normal supply pressure to confirm ther are no leaks and that fill times meet the appliance’s specifications.
- Common symptoms indicating tube issues: slow fill, visible leaks at joints, and ice buildup inside the line.
- Installation checks: proper seating on barbs, use of original-style clamps/tabs, and avoidance of sharp bends.
- Behavioral note: the tube will only pass water when the inlet valve opens; intermittent dispensing typically points to valve or pressure problems rather than the tube itself.
| Item | Description |
|---|---|
| Function | Routes potable water from the inlet valve to dispenser and icemaker, preserving factory flow and mounting alignment. |
| Material | Molded thermoplastic (common materials: nylon or polyethylene) resistant to cold temperatures and refrigerator chemicals. |
| Typical issue | Cracking,kinking,or improper seating causing leaks,restricted flow,or ice blockages. |
Common failure symptoms and measurable diagnostic indicators of water tube fill malfunction
The 241796405 Frigidaire Refrigerator Water Tube Fill routes metered water from the inlet valve to the ice maker and dispenser. Its proper function depends on an unobstructed bore and secure fittings to the valve and ice-maker fill cup; compatibility is primarily mechanical (tube diameter, clip locations) and material-based (resistance to mineral buildup).Typical failure modes are physical-kinking, abrasion, splits at barbed fittings-or internal restriction from scale and particulate.In practical service, a detached or cracked tube will produce visible leaks and pooling, while internal scale will present as slow fill rates or incomplete ice maker cycles even though the valve and control circuitry actuate normally.
technicians can confirm a tube-fill malfunction with a combination of functional checks and simple measurements. Common observable symptoms include the items listed below, and diagnostic metrics to record are fill time per cycle, measured dispense volume, inlet water pressure, valve coil continuity, and whether proper actuation voltage appears at the valve terminals. A systematic approach-timing a fill cycle while measuring flow, checking for voltage during that interval, and visually inspecting the tube path for frost, kinks, or deposits-quickly isolates whether the problem is the tubing, the valve, the water supply, or the control system.
- No water from dispenser or ice maker despite valve actuation
- Slow fill or extended ice maker harvest times
- Leaks or water pooling near the ice maker or refrigerator base
- Intermittent overfill or water within the freezer compartment
- Visible frost or mineral buildup around the tube or fittings
| Item | Description |
|---|---|
| Fill time | Seconds measured during a single commanded fill; increases indicate restriction |
| flow rate | Volume collected per unit time from dispenser or ice-maker tube to quantify blockage |
| Inlet pressure | Static water pressure at refrigerator connection; low pressure can mimic tube restriction |
| Valve coil continuity/voltage | Electrical continuity and applied voltage during actuation distinguish electrical from hydraulic faults |
Replacement considerations, model compatibility, and step-by-step installation precautions for the 241796405 water tube fill
The 241796405 Frigidaire Refrigerator Water Tube Fill is the conduit that transfers pressurized potable water from the inlet valve to the ice maker fill cup or dispenser inlet. In normal operation the tube must resist intermittent pressure pulses, remain dimensionally stable at near-freezing temperatures, and seat correctly in its fittings to produce repeatable fill volumes; failures typically present as slow fills, intermittent leaks at fittings, or water pooling in the ice maker area. When evaluating replacement parts,confirm the tube’s connector style (barbed,quick-connect push-fit,or molded end),inner/outer diameter,wall material,and whether it includes integral clips or grommets-mismatched connector geometry or diameter can produce poor sealing even when the tube length appears correct.
Replacement decisions should prioritize functional compatibility over cosmetic similarity: check the refrigerator model and serial number against OEM cross-reference tables and inspect the mating inlet valve and ice maker ports for corrosion or damaged O-rings before installing a new tube. During installation,route the tube to avoid sharp bends and heat sources,secure it with existing clips or new clamps to prevent chafing,and verify the ice maker fill volume by running a manual fill cycle after reconnecting power and the water supply. If the original failure was caused by mineral buildup or a clogged filter, replace the inline filter or clean the valve screen to prevent premature re-clogging of the new tube.
- Shut off the water supply and disconnect power before removing the old tube to prevent flooding and accidental ice-maker operation.
- Depressurize the line by running the dispenser briefly or opening a downstream valve, then cap the inlet to keep debris out.
- Replace any worn O-rings or push-fit connectors rather than reusing them; lubricate O-rings with food-grade silicone if required.
- Avoid kinking: maintain a minimum bend radius and secure the tube at clip points to minimize vibration and rubbing.
- Tighten clamps only to hand-firm plus a small turn; over-tightening can deform tubing and cause leaks.
- After reassembly, slowly restore water pressure and inspect all joints at operating pressure; run a test fill to confirm correct volume and absence of leaks.
| Item | Description |
|---|---|
| Typical tube OD/ID | ~1/4″ nominal OD (verify with measurements for exact fit) |
| Material | Flexible nylon or polyethylene with high cold-temperature stability |
| Connector types | Barbed with clamp, push-fit quick-connect, or molded OEM fittings |
| Compatibility note | Confirm 241796405 or approved cross-reference with refrigerator model/serial before purchase |
Q&A
what is the 241796405 Frigidaire Refrigerator Water Tube Fill?
241796405 is an OEM water fill/tube assembly used on certain frigidaire refrigerators to route water from the household water line and inlet valve to the ice maker and/or dispenser. It is a molded plastic/tubing part designed to deliver measured fills and to fit specific cabinet geometry on compatible models.
How do I know if the water tube fill (241796405) is failing?
Common symptoms include the ice maker not filling, slow or no water from the dispenser (if routed to dispenser), visible leaks or water pooling inside the freezer or under the refrigerator, or a water fill that sputters or sprays. You may also find the tube cracked, kinked, frozen, or clogged with mineral deposits on inspection.
How can I test whether the tube is the problem or the water inlet valve/other components are at fault?
First shut off water and power, then visually inspect the tube for cracks, kinks, or ice blockage. To isolate the tube: remove it and try to blow or run water through it to check for blockages. If water reaches the inlet side but not the ice maker/dispenser when the valve is energized, the tube may be blocked. If no water leaves the valve when energized, test the inlet valve (electrical continuity and correct voltage per the service manual) – frequently enough the valve, not the tube, is the cause of a no-fill condition.
Is the 241796405 water tube fill compatible with my refrigerator model?
Compatibility depends on the refrigerator model. Do not assume interchangeability. verify fit by checking your fridge model number and cross-referencing with Frigidaire parts diagrams or a trusted parts supplier. Using the exact OEM part number (241796405) is the safest way to ensure proper fit and routing.
Can I replace the 241796405 myself, and what safety steps should I follow?
A competent DIYer or technician can replace it, but always disconnect electrical power and shut off the water supply before starting. Allow the freezer to warm slightly if the tube is frozen, remove any trim/panels that block access, note routing and clamp locations, replace the tube and any seals/clamps, then restore water and power and check for leaks.If you are not comfortable working with plumbing or accessing internal refrigerator panels, hire a qualified appliance technician.
What tools and replacement materials will I need for installation?
Typical tools: screwdrivers (Phillips and flat), nut driver or socket set, pliers, tubing cutters (if required), and a flashlight. Supplies: the new OEM tube (241796405) and replacement clamps or grommets as needed.Use manufacturer-recommended fittings and do not overtighten plastic fittings; replace any worn gaskets to ensure a leak-free seal.
How do I prevent future problems with the water fill tube (clogs or freezing)?
Preventative measures: ensure the tube is routed away from evaporator coils or fan airflow that could cause freezing, avoid sharp bends or kinks, use anti-freeze routing clips/grommets supplied by the manufacturer, maintain proper freezer temperature, and install a water filter or softener if you have hard water to reduce mineral buildup. Periodically inspect for wear and replace small components (clamps/grommets) as they age.
How much should replacement of part 241796405 cost and where can I buy it?
Prices vary by supplier; the part itself is typically inexpensive compared with labor costs, but exact pricing depends on retailer and availability. Buy from Frigidaire-authorized parts dealers, major appliance parts websites, or reputable local appliance parts stores.If you hire a technician, include labor in your estimate – expect 30-90 minutes of labor depending on access and model complexity.
The Conclusion
The 241796405 Frigidaire refrigerator water tube fill is a small but essential component that controls the delivery of water to the ice maker and dispenser. By directing water flow and maintaining a sealed pathway, this tube helps ensure accurate fill cycles, prevents leaks and pooling, and supports overall water quality and appliance performance. When functioning correctly, it contributes to the refrigerator’s reliability and to the consistent production of ice and properly filled dispensers.
Accurate diagnosis is critical when water delivery problems arise. Identifying whether issues stem from the water tube,a valve,the inlet supply,or internal ice maker controls prevents unneeded part replacement and reduces the risk of further damage. When inspection indicates that the 241796405 tube is cracked, blocked, or worn, replacing it with the compatible part and installing it according to the manufacturer’s guidance restores proper function. observing basic safety precautions and, when appropriate, consulting a qualified technician will ensure the work is completed correctly.
the 241796405 water tube fill is integral to the refrigerator’s water management system, and careful assessment followed by timely, correct replacement preserves appliance performance and minimizes water-related issues. Prioritizing proper diagnosis, correct part selection, and professional service when needed helps maintain longevity and dependable operation of the refrigerator’s water and ice systems.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
The Blincoo Elite 48" Heavy Duty Dog Rope Toy is made for large breeds that love tug-of-war, chewing, and active play. Strong, simple, and fun for powerful dogs.
Shop on TikTok