316011200 Frigidaire Oven Top Burner Ignitor is a replacement ignitor assembly used on Frigidaire gas ranges adn cooktops; it is indeed a hot-surface/resistive-type ignition component designed to reach an incandescent temperature sufficient to ignite burner gas. as a hardware component it typically consists of a ceramic-encased resistive element and mounting hardware with a wiring connector, and is specified by electrical characteristics and physical dimensions that must match the appliance’s requirements.
Within the appliance the ignitor interfaces directly with the gas ignition and control subsystems: it is energized by the range’s control module or spark/ignition module, heats to ignition temperature to light the gas delivered by the valve/manifold, and works in conjunction with safety interlocks and sensing circuits that prevent gas flow until the ignitor draws the required current or a verified flame is present. Proper operation therefore depends on correct voltage supply, intact wiring and connectors, and compatibility with the range’s valve and control logic.
In this article readers will find a technical overview of the 316011200 ignitor’s function and key specifications, guidance on model and connector compatibility, common failure symptoms and diagnostic checks (resistance, voltage under load, visual inspection of the element and harness), troubleshooting procedures to isolate ignition versus gas-supply faults, and practical considerations for safe replacement and reinstallation such as matching electrical ratings, mounting orientation, and verifying sealing and clearance to adjacent components.
Table of Contents
- Function and Role of the Oven Top Burner Ignitor in Frigidaire Ranges
- How the 316011200 Frigidaire Oven Top Burner Ignitor Works Inside the Appliance
- Common Failure Symptoms and Electrical Indicators of a Faulty Top Burner Ignitor
- Troubleshooting procedures and Diagnostic Tests for Top Burner Ignitor Failures
- Q&A
- Wrapping Up
Function and Role of the Oven Top Burner Ignitor in Frigidaire Ranges
The 316011200 Frigidaire Oven Top Burner Ignitor is an electrode-type spark ignitor that provides the high-voltage pulses necessary to ionize the gas at a surface burner and initiate combustion.in normal operation the ignitor delivers repeated voltage pulses across an insulated gap at the burner head when a control requests heat; once a stable flame is established the control ceases pulsing. The component’s mechanical mounting,electrode geometry,and electrical connector are matched to specific Frigidaire control and valve assemblies,so using the correct part number preserves the designed spark gap and alignment that affect reliable ignition and flame sensing.
- Common failure symptoms: continuous clicking with no flame, weak or no visible spark, intermittent ignition, or visible damage/corrosion on the electrode.
- Functional behavior: emits high-voltage pulses onyl during the ignition phase and stops after flame is detected; does not act as a sustained heater.
- Compatibility considerations: replacement must match mounting bracket,connector type,and electrode position to avoid misfires or arcing to adjacent metal parts.
Technically, failures arise from cracked ceramic insulators, eroded or fouled electrode tips, damaged wiring/connectors, or internal open circuits; thes faults change the electrical path or the effective spark gap and prevent reliable ignition. For troubleshooting, technicians confirm pulsed output from the ignition module, inspect the electrode tip and insulator for contamination, and verify secure, corrosion-free connections; replacing the ignitor with the correct 316011200 assembly restores the intended electrode geometry and mounting clearances, reducing the chance of cross-arcing or repeated cycling. In practice, a range that clicks repeatedly without lighting frequently enough indicates electrode damage or a lost high-voltage path, while intermittent sparks frequently point to loose mounting or a deteriorating connector.
| Item | Description |
|---|---|
| Part | 316011200 Frigidaire oven top burner ignitor (electrode assembly) |
| Function | Spark generation for surface burner ignition and flame initiation |
| Mounting | Bracket-mounted at burner head; orientation determines spark gap |
| Connection | Two-conductor connector to ignition module/control (verify fit) |
How the 316011200 Frigidaire Oven Top Burner Ignitor Works Inside the Appliance
The 316011200 Frigidaire Oven Top Burner Ignitor is the electrical ignition element that provides the localized energy needed to ignite gas at the cooktop burners. In affected Frigidaire ranges the ignitor converts supplied electrical power into either a high-temperature glow or a timed spark, depending on the burner design, and must reach a specific operating condition before the gas valve is allowed to open. It interfaces directly with the appliance’s ignition module and wiring harness,so correct mechanical fit,connector type,and electrical rating determine compatibility with a given model.
inside the appliance the ignitor behaves as a controlled source: a control board or switch applies voltage, the ignitor produces the ignition energy, and flame establishment is confirmed either by a flame-sensing circuit or by timed control logic. Technicians use visual checks (visible glow or spark),continuity/voltage tests at the harness,and verification of mounting and connector geometry when diagnosing failures or selecting a replacement. Proper installation requires securing the bracket and ensuring the electrical connections match the original part to maintain safe, repeatable ignition performance.
- Observable behavior: glow or spark when energized; delayed or failed ignition indicates wear or damage.
- Common symptoms: burner does not light, long ignition delay, or intermittent lighting.
- Compatibility checks: match connector, mounting flange, and electrical rating before replacement.
| Item | Description |
|---|---|
| Function | Provides the ignition energy (hot surface or spark) to ignite cooktop gas. |
| Interface | Electrical connector and mounting flange that must match the range harness and bracket. |
| Diagnostics | Visual glow/spark check, harness voltage measurement, and continuity/resistance verification per service manual. |
Common Failure Symptoms and Electrical Indicators of a Faulty Top Burner Ignitor
The 316011200 Frigidaire Oven Top Burner Ignitor is a hot-surface ignition element that heats to a visible red glow to initiate gas flow for the oven’s top burner. Functionally it is a resistive heating element that must reach sufficient temperature and draw enough current to allow the gas safety valve to open; a correct replacement must match the OEM part number, connector type, and mounting footprint to ensure electrical and mechanical compatibility. In normal operation the ignitor reaches operating temperature within a few seconds of receiving mains voltage and exhibits steady, radiant emission; physical damage, cracked ceramic, or degraded filaments reduce heating efficiency and change its electrical signature.
Failure of this ignitor presents both visual and measurable electrical indicators. Typical diagnostic checks are a resistance/continuity test with a multimeter and an operating current measurement with a clamp ammeter: a healthy element usually shows cold resistance in the range of tens to a few hundred ohms and draws several amps when powered; an open circuit or a resistance that is significantly higher than the expected range indicates a failed element. Practical examples include an ignitor that glows weakly or slowly (reduced current or partial filament failure), repeated clicking of the gas valve without ignition (ignitor not reaching required current), or no glow at all (open circuit). Assessing both visual behavior and electrical readings helps distinguish a weak-but-present ignitor from wiring or gas-valve faults.
- No visible glow or open circuit on continuity check
- Dim or slow-to-glow ignitor with delayed ignition
- Repeated gas-valve clicking but no ignition
- High cold resistance compared with manufacturer or OEM reference
| Item | Description |
|---|---|
| Cold resistance (approx.) | Tens to a few hundred ohms; open/infinite = failed |
| Operating current (typical) | Requires several amps under mains voltage; significantly lower current suggests a weak ignitor |
| Visible behavior | Bright red glow within seconds when healthy; dim or no glow indicates degradation |
troubleshooting Procedures and Diagnostic Tests for Top Burner Ignitor Failures
The 316011200 Frigidaire Oven Top burner Ignitor is the electrode assembly that initiates the gas-air mixture ignition on surface burners; it functions as the high-voltage spark point and as a mechanical interface between the burner and the ignition module. Typical failure modes include cracked or fouled ceramic insulation, carbon tracking from spatter and grease, broken leads or connector corrosion, and loss of electrical continuity.because top-burner ignitors must match the ignition module’s electrode spacing, lead length, and connector type, confirm OEM cross-reference and physical compatibility with a given Frigidaire model before replacing the part.
- No spark at the burner during the ignition cycle – inspect for broken or fouled electrode and check for continuity.
- Intermittent sparking or continuous clicking – examine the electrode for carbon tracking and test the ignition switch and spark module.
- Visible physical damage (cracked ceramic, bent electrode) – replace the ignitor rather than attempting repairs.
Troubleshooting procedures start with eliminating power and gas at the appliance and performing a visual inspection of the ignitor, connector, and harness. Use a multimeter to check for continuity across the ignitor leads; an open circuit indicates internal failure. If continuity is present, energize the range briefly (following safety protocols) to verify that the ignition module supplies the correct switching signal to the ignitor connector and that the electrode produces a consistent spark; if the module is not providing voltage, isolate and test the switch and wiring. Practical diagnostics include cleaning the electrode to remove carbon tracking, swapping with a known-good ignitor when available, and verifying connector pin alignment – replacements should match connector type, lead length, and electrode geometry to ensure reliable ignition and safe operation.
| Item | Description |
|---|---|
| Common symptom | No spark, intermittent spark, or continuous clicking; check electrode condition, continuity, and ignition module output. |
Q&A
What is the Frigidaire part 316011200 and what does it do?
Part 316011200 is a replacement ignitor used on Frigidaire gas ranges/ovens to light the burner. The ignitor heats (glows) or produces the spark necessary to open the gas valve and ignite the burner.it is an OEM-style part meant to restore proper ignition when the original ignitor has failed.
How do I know if the ignitor is the problem and not the gas supply or valve?
Common signs of a bad ignitor include: no glow when the burner is turned on, very slow or weak glow, or the ignitor glows but the burner never lights and gas keeps flowing. To isolate the issue safely, first confirm power to the range and listen for the ignitor circuit clicking. Visually inspect for cracking or damage. If the ignitor glows but the burner won’t light, the gas valve or safety valve may be the issue. If the ignitor does not glow or has no continuity, the ignitor itself is most likely defective.
How can I test the 316011200 ignitor?
Before testing,disconnect the appliance from power and,if applicable,shut off the gas. Visually inspect the ignitor for cracks or damage. Use a multimeter set to measure continuity or resistance: check for continuity across the ignitor leads – an open circuit usually means the ignitor is faulty. For live testing (only if you are trained and pleasant), the ignitor should glow when the burner is turned on; if it does not glow but receives power, replace it. If you are not experienced with electrical or gas components, have a qualified technician perform tests.
how do I replace the 316011200 ignitor safely?
Turn off and disconnect electrical power to the range and shut off gas supply. Remove any cooktop/burner components or access panels required to reach the ignitor. Disconnect the ignitor wiring harness and unfasten mounting screws or clips. Install the new ignitor in the same orientation,secure it,reconnect wiring,restore power and gas,and test ignition. If you are not comfortable working with gas or electrical connections, hire a qualified appliance technician.
Is this ignitor compatible with my Frigidaire model?
Compatibility depends on your specific Frigidaire model number. Always check the parts list or model-specific parts diagram (frequently enough available on Frigidaire’s website or parts retailers) before ordering. You can also provide the appliance model number to a parts supplier or technician to confirm that 316011200 is the correct replacement.
How long should the ignitor last and what reduces its lifespan?
Ignitor lifespan varies by usage and handling; many last several years. Factors that shorten life include frequent on/off cycling, physical damage, and contamination from oils or grime. Avoid touching the ignitor element with bare hands (skin oils can create hot spots), and keep burners clean to help extend service life.
Can I replace the ignitor myself or should I hire a technician?
If you have basic mechanical skills, can safely disconnect power and gas, and follow the manufacturer’s instructions, you can replace the ignitor yourself. However, if you are uncomfortable working with gas lines or electrical wiring, or if the diagnosis is unclear (for example, if the ignitor glows but the burner will not light), hire a qualified appliance technician to ensure safe and correct repair.
Where can I buy part 316011200 and what should I look for when purchasing?
You can buy the part from Frigidaire-authorized dealers, major appliance parts retailers, or reputable online parts stores. When purchasing, confirm the part number, verify compatibility with your model, check return policies and warranty facts, and prefer OEM or high-quality replacement parts to ensure proper fit and reliable operation.
Wrapping Up
The 316011200 Frigidaire oven top burner ignitor is a small but critical component that initiates combustion and enables consistent, efficient heating in the cooktop/oven assembly. By producing the required spark or glow to ignite gas, a properly functioning ignitor contributes directly to reliable burner operation, consistent cooking performance, reduced risk of delayed ignition or gas buildup, and overall appliance safety.
Accurate diagnosis is essential when ignition issues arise. Symptoms such as weak or non‑glowing ignitors, intermittent ignition, prolonged spark attempts, or unusual odors merit careful inspection and testing to distinguish ignitor failure from other causes (for example, gas supply, valves, wiring, or control electronics). Thoughtful troubleshooting-using the manufacturer’s guidance and appropriate test tools-helps avoid needless parts replacement and ensures the true fault is addressed.
When replacement is required, using the correct specification part and following proper installation practices restores performance and minimizes safety risks. Installation should follow manufacturer instructions and local safety codes; if there is any doubt about wiring, gas connections, or safe procedures, engaging a qualified service technician is advisable. Timely, correct replacement of the 316011200 ignitor supports appliance longevity, dependable cooking results, and safe operation.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
The Blincoo Elite 48" Heavy Duty Dog Rope Toy is made for large breeds that love tug-of-war, chewing, and active play. Strong, simple, and fun for powerful dogs.
Shop on TikTok