134156200 Frigidaire Screw is an OEM fastener used in frigidaire appliances to secure panels, brackets, and assemblies; it is not an electronic or mechanical subassembly but a retention component crucial to the mechanical integrity of the appliance. As a screw-type fastener, it will be specified by head style, drive type, thread form, length and material finish, and is selected to match the mating substrates and environmental conditions found in household appliances.
Inside an appliance the 134156200 Frigidaire Screw provides mechanical retention and alignment between parts and can also serve secondary functions such as providing an electrical grounding path or compressing gaskets and seals. It typically interacts with sheet-metal housings, mounting brackets, control modules and trim pieces; its thread engagement, clamping force and corrosion resistance influence vibration resistance, panel flatness and long-term assembly reliability.Proper selection and installation affect serviceability,noise generation,and the durability of adjacent components.
In this article you will find technical data on the screw’s intended function, common locations and compatibility considerations, typical failure symptoms to watch for (for example loose or missing fasteners, stripped threads, or corrosion), practical troubleshooting steps (visual inspection, torque checks, thread assessment and repair options) and replacement considerations (matching thread size, length, head and finish, and when to use locking features or thread inserts). The goal is to provide technicians, engineers and appliance owners with the details needed to diagnose fastener-related problems and make appropriate, safe replacement or repair decisions.
Table of Contents
- Function and Role of the Part in Frigidaire Appliance Assemblies
- How the 134156200 Frigidaire Screw Works Inside the Appliance
- Common Failure Symptoms and Wear Indicators for the 134156200 Frigidaire Screw
- Replacement Considerations, Compatibility with Frigidaire Models, and Installation Procedures
- Q&A
- insights and Conclusions
Function and Role of the Part in frigidaire Appliance Assemblies
134156200 Frigidaire Screw serves as a dedicated mechanical fastener within Frigidaire appliance assemblies, used to secure panels, mounting brackets, control modules, and other serviceable components. In metal-to-metal joints it transmits clamping load and can provide a low-impedance path for chassis grounding when tightened against conductive surfaces; when used with plastic parts it must limit compressive stress to avoid cracking. Correct matching of thread form, engagement length, head style and plating is necessary to achieve intended clamp load and to avoid common failure modes such as thread stripping, cross-threading, or loss of electrical contact.
The effective behavior of this screw in service depends on thread engagement, applied torque, and environmental exposure (temperature, humidity, vibration). Applications with meaningful vibration or thermal cycling – such as, blower motor mounts, compressor brackets, or door hinges – frequently enough require additional retention measures (lock washers, adhesive threadlock, or captive nut designs) to maintain preload. When replacing the screw, use a replacement that matches the original geometry and material characteristics; an incorrect length or thread type can produce poor seating, reduced clamp force, or damage to mating components.
- Primary functions: fastening structural panels, mounting components, and in some locations providing electrical bonding.
- Compatibility concerns: thread form, engagement length, head type, and corrosion-resistant plating.
- Service considerations: correct torque, use of washers/lockers in vibration-prone locations, and avoiding overtightening on plastics.
| Item | Description |
|---|---|
| Function | Mechanical fastening of panels, brackets and component modules; occasional chassis grounding. |
| Material | Typically steel with corrosion-resistant plating or stainless steel for humid compartments. |
| Typical mating | Sheet-metal threaded holes, captive nuts, or self-tapping engagements depending on location. |
| Replacement guidance | Match thread type, length, head style and plating to maintain clamp load and fit; avoid undersized or mismatched threads. |
How the 134156200 Frigidaire Screw Works Inside the Appliance
The 134156200 Frigidaire Screw is a purpose-designed fastener used to secure internal assemblies such as control brackets, mounting plates, and door components.Its mechanical role is to provide clamping force and maintain positional stability under thermal cycling and vibration; the screw’s head style, drive type, and thread form determine whether it pulls two metal parts into contact, engages a molded plastic boss, or cuts its own mating thread.When installed to the correct torque, the fastener distributes load across the mating surfaces and resists loosening; if over‑torqued it can strip threads in softer substrates, and if under‑torqued it will allow movement and intermittent electrical or mechanical faults.
Compatibility is governed by thread profile, length, and material choice-replacement screws must match the original dimensions and material properties to preserve clamping force and corrosion resistance. Technicians assess condition by checking for stripped heads, elongated holes, or deformed plastic bosses; common remedial actions include installing a correctly sized insert or using a slightly longer screw with the same thread form when the original mating surface is damaged. Practical examples: a metal-to-metal mounting typically tolerates higher torque than a screw into an ABS boss, and panels that rattle after service often indicate either a missing screw or a worn thread rather than a problem with the panel itself.
- Key features: head/drive compatibility, thread engagement behavior, and material selection.
- Common failure signs: loose panels, vibration-induced noise, stripped threads in plastic bosses.
- Installation tip: verify thread pitch and use the correct torque driver or a self-locking washer for high-vibration locations.
| Item | Description |
|---|---|
| typical request | Securing control brackets, panels, and door components inside Frigidaire appliances |
| Inspection point | Check head condition, thread engagement, and mating surface for deformation |
Common Failure Symptoms and Wear Indicators for the 134156200 Frigidaire Screw
The 134156200 Frigidaire Screw is a service-replaceable fastener used to secure internal appliance parts such as mounting brackets, access panels, and linkage points. As a machine screw intended for factory-mated holes,its primary function is to provide consistent clamping force and repeatable alignment; using the correct part maintains thread engagement and prevents stress concentrations that lead to premature fatigue. Compatibility with the original thread form, length, and material finish is essential because incorrect substitutes can strip mating threads, cause galvanic corrosion, or fail to hold the required preload under vibration and thermal cycling.
Common failure symptoms are mechanical rather than electrical and are usually evident through inspection or simple functional tests. Look for a rounded or cammed drive recess, which indicates frequent servicing with an improper driver; thread deformation or cross-threading, which reduces axial clamping and can produce metal shavings; and corrosion or pitting on the shaft that shortens usable thread length. A quick torque check with a calibrated driver and a visual inspection for play or movement in the assembled parts will distinguish a loose fastener from a stripped thread that requires repair or replacement with the correct OEM screw.
- Rounded drive recess – repeated cam-out or wrong driver size
- Cross-threading or stripped threads – improper installation or wrong thread form
- Visible corrosion or pitting – environmental exposure reducing thread engagement
- Rattling or movement under load – loss of preload or fatigued fastener
- Metal shavings at mating surface – shearing or severe over-torque
| Item | Description |
|---|---|
| Typical inspection | Visual check of drive, shaft, and thread runout; torque verification |
| Likely corrective action | Replace screw if drive or threads are damaged; repair mating thread if stripped |
Replacement Considerations, Compatibility with Frigidaire Models, and Installation Procedures
The 134156200 Frigidaire Screw is an OEM fastener used to secure panels, brackets, and components in specific Frigidaire appliance assemblies. As a mechanical clamp, the screw provides axial compression and thread engagement between mating parts; its effectiveness depends on correct thread form, length, and plating. Using an incorrect substitute can lead to stripped holes, inadequate clamp load, or galvanic corrosion between dissimilar metals, so matching the original head style and thread characteristics avoids common failure modes. Inspect the screw head, shank length, and plating before reuse, and ensure the mating threads are clean and undamaged to restore intended mechanical and electrical continuity where applicable.
Compatibility checks and installation require deliberate verification of fit and installation torque rather than visual matching alone. Confirm the OEM part number against the appliance service manual, measure thread engagement to ensure at least several full turns into the parent material, and use a driver or torque screwdriver set to the service-recommended value for sheet metal or threaded inserts. If threads are damaged,repair with a correctly sized insert or a replacement captive fastener instead of forcing a mismatched screw; likewise,avoid over-length screws that can contact wiring,sensors,or evaporator tubing. After installation,perform a functional check of the secured assembly and recheck torque after initial cycling to confirm retained clamp load.
- Confirm part number and head style match the original screw.
- Measure shank length and thread pitch before installation.
- Use correct torque setting and a compatible driver bit to prevent cam-out.
- Repair stripped threads with an insert rather than oversizing the fastener.
| Item | Description |
|---|---|
| Part number | 134156200 Frigidaire screw (OEM fastener for specific frigidaire assemblies) |
| Material / Finish | Typically plated steel; verify corrosion resistance for wet locations |
| Thread type | Match machine or sheet-metal thread as specified in service documentation |
| Typical application | Securing panels, brackets, and trim where controlled clamp load is required |
Q&A
What is Frigidaire part 134156200?
frigidaire part 134156200 is an OEM screw used by Frigidaire in one or more of their appliances. It is a factory-specified fastener (typically a sheet‑metal/self‑tapping or machine screw) used to secure panels, brackets or small components. The exact geometry and finish are defined on the appliance’s parts fiche.
how can I confirm that 134156200 is the correct screw for my model?
Confirm compatibility by checking the parts diagram (parts fiche) for your appliance model number. Enter the full model number on Frigidaire’s parts site or on reputable parts retailers (e.g., PartSelect, RepairClinic, AppliancePartsPros) and verify that 134156200 appears in the diagram where the screw is shown. If you have the screw on hand, compare head style, thread form and length to the fiche illustration or the removed screw.
What are the dimensions and head type of screw 134156200?
Exact dimensions (diameter,length,thread pitch and head style) are specified on Frigidaire’s parts fiche. In practice this screw is commonly a small sheet‑metal/self‑tapping or machine screw with a Phillips, pan or hex head depending on the application. If you need a replacement and the fiche doesn’t list measurements,measure the old screw: length is measured from under the head,diameter with calipers,and note head type and thread form before sourcing a match.
Can I use a generic screw from a hardware store as a replacement for 134156200?
Yes, you can use a generic screw if it matches the OEM screw in material (usually plated steel or stainless), diameter, thread type (self‑tapping vs. machine), length and head style.However, for critical mounting points, electrical components or if the original is a specified OEM fastener, it’s best to use the exact Frigidaire part to ensure fit, finish and longevity.
What tools and technique should I use to remove or install 134156200 without damaging the appliance?
use the correctly sized screwdriver or bit that fully engages the screw head (Phillips,Torx or hex as applicable). Turn slowly and apply steady pressure to avoid cam‑out.For installation, align parts so threads engage cleanly, start by hand to avoid cross‑threading, then tighten until snug-do not over‑torque.If the screw secures a thin sheet metal panel or plastic part, stop when the part is seated; overtightening can strip threads or crack plastics.
What should I do if 134156200 is stripped, corroded or stuck?
For stripped heads try: using a slightly larger screwdriver, pressing a rubber band between driver and head for extra grip, or using a screwdriver extractor kit. For seized or corroded screws apply penetrating oil (allow time to soak), tap the head gently to break corrosion, and use an impact driver if appropriate. If removal damages threads, replace the screw and, if necessary, repair the thread (use a slightly larger self‑tapping screw, a helicoil for machine threads, or a threaded insert) using a method suited to the substrate.
Where can I purchase part 134156200?
Purchase the OEM part from Frigidaire-authorized dealers or online appliance parts retailers (FrigidaireParts, PartSelect, RepairClinic, AppliancePartsPros, etc.). You can also check local appliance repair shops or order from online marketplaces if the seller lists the exact Frigidaire part number. If the OEM part is unavailable, bring the original screw to a hardware store to match size, thread and head style.
Is screw 134156200 critical for appliance safety or performance?
Whether it is critical depends on where the screw is used. screws that secure control panels, door hinges, heating elements, or grounding connections can affect safety and operation and should be replaced like‑for‑like. Screws used for cosmetic trims or non‑structural panels are less critical but should still be correct to prevent rattles or loose parts. When in doubt, replace with the OEM part or an exact equivalent.
Insights and Conclusions
Although small and often overlooked, the 134156200 Frigidaire screw plays a specific and significant role in the reliable operation of compatible Frigidaire appliances.As an OEM fastener it is designed to provide the correct fit, material properties and clamping force for the components it secures, helping to maintain alignment, suppress vibration, preserve seals and support electrical or mechanical connections. using the correct part helps maintain the appliance’s intended performance, safety and longevity.
Because the consequences of a missing, damaged or incorrect screw can range from noise and misalignment to more significant mechanical or safety issues, proper diagnosis and careful replacement are essential. Troubleshoot with visual inspection and model-specific documentation, verify the part number before replacing, and follow recommended installation practices (including correct tools and torque). When the repair is beyond basic fastening or when warranty and safety are a concern, seek a qualified technician. Timely and correct replacement of part 134156200 helps restore proper function and reduces the risk of further damage.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
