A00099902 Frigidaire âDishwasherâ Doorâ latch isâ an electromechanical door latch and interlock assembly used on Frigidaire dishwashers. as a hardware component â¤it combines a mechanical catch âŁwith an electrical switch (interlock) to secure the doorâ in the closed position and signal the appliance control that the door is latched. The assembly is typically mounted to the âdoor or cabinet frameâ and interfaces directly with â¤the doorâ strike and surrounding trim; its form factorâ and mounting points are designed to align with factory door hinges, gaskets,â and⣠seals.
inside the appliance system the latch performs⤠two primary functions: it provides âŁthe⢠mechanical retention necessary⤠to maintain a watertight seal â˘under pressure andâ vibration, and it âprovides an electrical interlock input⣠to the âcontrol board so that âwash cyclesâ only run when⢠the door is properly closed.the latch therefore interacts with⢠the door seal andâ hinge geometry, the âŁelectronic control module â(which monitors the interlock switch or sensor), and safety features â˘such as door-open detection and userâ interface â˘lockouts. Proper alignmentâ and electrical continuity of the latch areâ essential for preventingâ leaksâ and avoiding erroneous fault conditions that inhibit normal operation.
In this â˘article readers will âŁfind aâ technical⣠overview ofâ the âlatchâs functional⢠design,â compatibility notes âfor âOEM versusâ aftermarket replacements, and â¤common failure symptoms such⢠as inability to start a âcycle,â intermittent door-open faults, or observable leakage.The guide will â¤cover diagnostic steps including visualâ inspection, mechanical alignment checks, and basic â˘electrical continuity testing, as well as practical replacement⤠considerations-mounting orientation, connector types, seal condition, and verification procedures after installation. The focus is on providing technicians, engineers, and âappliance âŁowners with the information needed to assess, troubleshoot, and correctly install the latchâ while maintaining system integrity and safety.
Table of âŁContents
- Function and Role of the âŁDoor Latch Assembly in Frigidaire⢠Dishwashers
- How the A00099902 Frigidaire Dishwasher Door Latch Operates Within the Door, Interlock, âand Control Circuits
- Diagnostic Indicators⤠and⣠Common Failure â¤Symptoms â¤ofâ the A00099902 Door Latch
- Replacement Considerations, required parts, and StepâbyâStep Installation for the A00099902 Frigidaire dishwasher Door Latch
- Q&A
- In Retrospect
Function and Role of the Door Latch Assembly in Frigidaire Dishwashers
The A00099902 Frigidaireâ Dishwasher âDoor Latch is⤠a combined mechanical and âŁelectrical component that both secures the door under wash pressure and âprovides the door-closed signal to the appliance control. Mechanically, the latch engages the door âstrike to compress â˘the âgasket⣠and resist inward water pressure; electrically, an internal â¤switch closes when the latch is fully âengaged so the control board âŁwill enable the âpump, heater and âdoor lock indicators. Proper compatibility requires⢠matching the latchâs âmountingâ footprint,â actuator orientation and electrical connectorâ to the specific âŁFrigidaire âmodel – installing a physically diffrent latch or oneâ with a different harness â˘can result⤠in⣠improper engagementâ or an open-circuit⤠signal⢠even â¤if the part â˘superficially fits.
Typical failure modes include âŁbroken plastic⤠cams, â˘worn strikeâ surfaces, or failedâ switch contacts, which⤠produce â˘recognizable symptoms: no-start conditions, mid-cycle stoppages, or⣠water leaks at the front⣠of â˘the â˘door. For practical troubleshooting,perform a visual inspection for cracked housings and misalignment,manually operate the â˘latch while measuring continuity across the switchâ with a multimeter,and verify that the door gasket seats uniformly when latched. When replacing the latch, confirm connector pinout and secure mounting; after installation run a diagnostic âŁor a short cycle âto confirm the âcontrol sees the closed-door signal and that the door retains correct tension âŁwithout âexcessive play.
- Primary âfunctions: secure door âŁmechanically and close⢠the doorâ switch electrically
- Common symptoms of failure: dishwasher wonât start, stops mid-cycle, or door leaks
- Field â¤checks: visual⣠inspection, manual actuation, multimeter continuity test âwhen latched
- Replacementâ tip: match mounting points and⢠connector â¤type; verify operation with⢠a test cycle
| Item | Description |
|---|---|
| Part | A00099902 – door â˘latchâ assembly with integrated âŁdoor-closed switch |
| Location | Top edgeâ of⤠the inner door panel; secures to the door frame and aligns â˘with the strike |
| Field test | Measure continuityâ across switch terminals with latch engaged; inspect for broken cams or â¤loose mounting |
How the A00099902 Frigidaire Dishwasher âDoor Latch Operates Within the Door, Interlock, and Control Circuits
The A00099902 Frigidaire â¤Dishwasher Door â˘Latch is a combined âŁmechanical catch âand electrical switch assembly that mounts⤠into the dishwasher door⤠and engagesâ a striker âon theâ tub. When âthe door âcloses the latchS hook secures the door and âactuates one â˘or more internal contacts; those contacts provide the control board with a door-closed interlock signalâ and,⢠on someâ models, feed a separate âlock coil that holds the door during high-temperature or drying⢠phases. Physicallyâ the assembly must âmatch the door’s mounting points and the âŁharness⤠connector used byâ the model – the A00099902 form factor and terminal layout are intended to replace the original âlatch âin Frigidaire units that reference that part number, butâ installers should verify connector typeâ and⢠bracket alignment before installation to ensure proper mechanical engagement and sealing against the tub gasket.
In the âcontrol circuit theâ latch switch is typically placed in series with the control board’s door-sense input and any safety interlocks, so the boardâ will⣠not energize wash â˘or drain circuits until the latch presents a closed contact. Some designs use a normally openâ contactâ that â˘closes when latched, âŁwhile othersâ include an auxiliary contact⤠orâ coil for added âretention; wiring diagrams identify which âterminal performs each function.Practical troubleshooting includes checking for continuity âacross the⤠latch contacts with the⤠door latched, verifying correct voltage to a lock coil (if present), and confirming the control sees the closed-door signal. âTypical âfield symptoms â˘that point to a latch⣠issue include âŁa âunit that will not start, âintermittent âstopping mid-cycle, or an error âŁindicating the door âis open⣠despite correct closure; these conditionsâ are âŁbest diagnosed by confirming mechanical engagement, connector â˘integrity, and electrical⤠continuity before replacing the part.
- Symptoms to check:⢠no start, door-open error, intermittent cycle stop, audible âclick without motor action.
- Basic field test: power off, remove⤠inner door panel,⤠actuate latch and test continuity acrossâ labeled â¤terminals with âa multimeter.
| Item | Description |
|---|---|
| Latch âswitch (NO contact) | Provides the âŁdoor-closed âsignal to the control board; closes when the latch is fully engaged. |
| Retention coil / auxiliary contact | When present, energizes to hold the âŁdoor closed during⢠specific cycle phases or provides a secondary interlock contact. |
Diagnostic Indicators and Common Failure Symptoms of the A00099902 Door âŁLatch
The A00099902 Frigidaire Dishwasher Door Latch is a combined mechanical âcatch and electrical switch assembly that secures⣠the door and tells the control board when the door is fully⢠closed. âIn normal operation the latch provides a positive â˘mechanical âengagementâ with the door striker and compresses an internal microswitch⤠or switches to present a closed circuit to⤠the controller; the partâs plastic housing, âŁmounting⤠tabs, andâ connector pinout determine â¤compatibility with specific Frigidaire/white-westinghouse model lines, so replacement requiresâ verification of the part number and physical fit. Failures of the latch typically manifest as either purely mechanical faults â(broken âcatch, weak spring, misalignment) that prevent secure engagement, or âelectrical faults â(open or intermittent switch contacts, connector corrosion) that fail to signal the controlâ even when the door looks closed.
Diagnosing âŁa⢠faulty latch âŁcombines visual,mechanical,and electrical checks: visually inspect for cracked plastic,worn striker surfaces,or missing spring tension; manually actuate the latch while probing the harness for continuity to confirm the switch closes⢠reliably; and wiggle-testâ the connector and wiring for intermittent faults. Practical examples include a â˘dishwasher⢠that refuses to start with no control⣠errors (open-switch condition), one that starts but stops mid-cycle (intermittent contact), or one that showsâ a door-open error despite the door feeling latched (mechanical misalignment). Technicians should measure continuity with â˘the actuator depressed (closed = continuity,â open⢠= no continuity), check striker alignment relative âŁto the latch, and inspect the harness⤠for burned⤠pins or loose⣠terminals âbefore replacing the assembly.
- Dishwasher will not start or register⣠doorâ closed
- intermittent âcycle interruptions or stops mid-cycle
- Audible⤠clicking without lock âengagement
- Visible damage, cracked housing, or loose mounting tabs
| Item | Description |
|---|---|
| Electrical test | Probe microswitch contacts with a multimeter while actuating âlatch; closed position should⢠showâ continuity, open position shouldâ show no continuity. |
| Mechanical inspection | Check for broken catch, worn striker surfaces, weakened spring tension, and correct alignment of âmounting tabs. |
| compatibility check | Verify A00099902 part ânumber, connectorâ pinout, â˘and mounting geometry against the appliance model before⤠ordering replacement. |
Replacement Considerations, Required parts, and StepâbyâStep Installation for the A00099902 Frigidaire⣠Dishwasher Door Latch
The A00099902 Frigidaire Dishwasher Door Latch âŁis aâ combined mechanicalâ catch and electrical interlock that secures âthe door and signals the control board that âthe appliance is in the closed position. Mechanically, the latch â˘engages the striker on the door frame and provides sufficient retention â˘to compress⣠the door gasket for⤠a watertight seal; electrically, an âinternal microswitch or âsensor within theâ assembly closes the âcircuit so⣠the âwashâ cycle can start. Failures commonly observed include broken⤠plastic hook points, worn detents that allow the⢠door⢠to pop âopen under vibration, and intermittent switch contacts that â˘cause “door âopen” or no-start errors⤠despite a physically closed door.
Replacement requires⤠attention to alignment and wiring continuity rather than cosmetic âfit âalone;â a mismatched strikerâ position or under-torqued fasteners canâ reintroduce leaks or electrical faults after a new A00099902 latch is installed. Typical required parts and a concise installation sequence are listed below to guide technicians âand âŁexperienced appliance owners: follow proper lockout procedures, remove the inner door⣠panel to access the latch, document âand disconnect the wiring⤠harness, âremove retaining screws⤠and the old latch, install the new assembly â¤ensuringâ the striker andâ latch⢠engage smoothly, restore⢠wiring, andâ verify sensor continuity and âŁdoor operation⣠before reassembly âand final testing.
- Requiredâ parts: A00099902 latch assembly, replacement screws⣠(M4 or M5 sheet-metal screws as original),â optionalâ striker or door spring if worn, and âŁan exact wiring⢠harness if damaged.
- Key installation âchecks: Disconnect power, verify continuity across the latch switch with a multimeter âŁwhen actuated, confirm striker alignment so the⤠gasket compresses evenly, torque fasteners âto prevent loosening â¤but avoid over-tightening plastics.
- Functional tests: perform a manual â¤door close/open âŁcycle, run a short diagnostic drain/fill or test cycle, and watch for error codes or leaks.
| Item | Description |
|---|---|
| Mounting fasteners | M4/M5⤠sheet-metal screws; tighten⤠to firm⤠engagement â¤without crushing plastic (approx. 1.5-2.5 N¡m). |
| Electrical connector | 2-3 pin harness (verify pinout and wire colors before replacement); testâ forâ continuity and secure latch signal to âcontrol board. |
| Alignment check | Door striker should engage latch without binding and compress gasket uniformly;⢠adjust striker position if necessary. |
Q&A
What is the A00099902 Frigidaire dishwasher door latch?
The A00099902 is a replacement door⢠latch/strike assembly used on⢠certain Frigidaire dishwashers. It is⣠the mechanical interlock that secures the door⣠closed and usually contains or actuates the door âŁswitch (safety interlock) the control uses to confirm âŁthe door is closed⤠before starting âa cycle. Always verify fit by matching theâ part number to your model.
What are common⤠symptoms that the door latch â(A00099902) is failing?
Typical symptoms include the dishwasher not startingâ or not â˘responding when the door âis closed,the door popping open âduring a cycle,intermittent cycle â¤interruptions,a door-locked/door-unlocked error or⤠flashing â˘indicators,or visible damage such as a âcracked housing⤠or broken latch âhook.⣠Any of these canâ indicate a faulty latch âŁor its switch.
How can I test âthe door⢠latch to confirm it is indeed bad?
First âdo a visual inspection for broken plastic,⢠a bent strike, or loose âmounting. To test electrically, disconnect power and remove the inner door panel to access the latch wiring.â Use a multimeter set to⤠continuity or ohms: actuate the latch âand check⤠for continuity across the switch terminals-when the⤠latch âis in the closed (actuated) position âthe switch should show continuity (near 0â ohms).If the switch does not change state, or the mechanism is physically damaged, replace the âlatch.
Can I replace the A00099902 myself, and what tools are required?
Yes-many owners or technicians can replace âit. Always disconnect power â˘(unplugâ or turn offâ the breaker)⤠before starting. Typical tools:â Phillips or Torx screwdriver, nut driver, needle-nose pliers, and a multimeter (forâ testing).Procedure overview:â open the door,⢠remove âscrews â˘holding⢠the inner door panel (support theâ inner panel asâ you loosen screws), âdisconnect the âlatch wiring harness, remove theâ old latch, install the new latch, reconnect the harness, reassemble the door, restore power, and test. The door can be heavy or⣠awkward-having a second person to support the door is recommended.
How long does replacement usually take?
For someone⢠cozy with basic appliance work, replacement typically takes⤠20-60 minutes.â Time⣠variesâ depending on model accessibility, whether you need to remove the entire door or just the inner⢠panel, and your experience with small electrical connectors and fasteners.
How do âI confirm the A00099902 is compatible with my dishwasher model?
Locate your dishwasherâs model number (usually on the door frame or on⣠a label on the door edge).⢠Searchâ the Frigidaire partsâ lookup or authorized partsâ distributors for that model and⤠verify that A00099902 is listed as the correct door latch. Do ânot ârely on visual similarity alone-mounting points and connector⢠types canâ differ â¤between models.
What are⣠common â¤installation mistakes and tips âto avoid problems?
Common mistakes: not disconnecting power, overtightening screws (which âcan distort the latch or alignment), failingâ to⣠seat the gasket⢠or door seal correctly, misrouting or⣠pinching the wiring harness, and notâ supporting âthe door⤠while âŁremoving âthe inner panel. Tips: take photos⤠of wiring before unplugging, âtest continuity before full reassembly, ensure the latch engages smoothly⣠with⤠the strike and the door seals correctly, âŁand run a short cycle âto confirm âproper operation beforeâ closing the outer panel completely.
Whereâ should I buy the A00099902 and is there a warranty?
Buy from Frigidaire-authorized parts dealers, major appliance parts retailers, or the manufacturer’s official parts site to ensure you receive an OEM part. Aftermarket options exist but may vary in fit or longevity. Warranty⣠terms âdepend on the âsellerâ and manufacturer;â check the sellerâs return policy and Frigidaireâs warranty information-many OEM⢠parts come with⣠a limited partsâ warranty (terms vary âŁby region and vendor).
In⢠Retrospect
Theâ A00099902 â¤Frigidaire dishwasher door latch plays a central role in the applianceâs safeâ and reliable operation. As the mechanical and electrical interface that secures theâ door, engages the safety⤠interlock, and helps maintainâ a watertight seal, a properly functioning latch ensures wash cycles begin and run as â˘intended while preventing leaks and â˘unintended door openings. As the âlatch affects both user safety and machine performance, its condition directly influences overall dishwasherâ reliability.
Accurate âdiagnosis and appropriate replacement of the A00099902 latch are essential when⢠symptoms such âŁas failure⤠to start,intermittent cycle interruptions,or visible wearâ appear. Confirming the root cause-whetherâ latch wear, alignment issues, wiring faults, or unrelated control problems-avoidsâ unnecessary part changesâ and reduces downtime. When replacement is⣠required, using the correct, compatible part and following manufacturer guidance or⣠engaging a qualified technician helps restore proper function, maintain safety features, and prolong the service life of the appliance.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
