AJB73816015 Lg Stator Assembly Replacement, Fits Many is a replacement stator assembly intended for use in LG and compatible appliances that employ a brushless motor design. The stator is the stationary electromagnetic component of the motor; it contains the laminated core and windings that generate the rotating magnetic field used too drive the rotor and, ultimately, the appliance’s mechanical load.
Inside a washer or other motor-driven appliance,the stator works in direct interaction with the rotor (permanent magnets) and the appliance’s motor control electronics. The control board supplies commutated current to the stator windings based on rotor position feedback so that torque is produced in a controlled sequence. Mechanically the stator is mounted to the motor housing and interfaces with seals,bearings and the rotor air gap; electrically it connects to the harness and on-board drive electronics. As it is indeed responsible for converting electrical input into mechanical torque, its condition directly affects spin, agitation, balance and overall motor performance.
This article will explain the functional design of the AJB73816015 stator assembly, outline compatibility considerations and typical appliance applications, and describe common failure symptoms such as loss of spin, intermittent operation, unusual noise or overheating. It will also cover practical troubleshooting checks a technician can perform (visual inspection, continuity and resistance measurements, connector and insulation assessment), and key replacement considerations including mechanical fit, electrical connections, sealing and safety precautions to observe during removal and installation.
Table of Contents
- Function and Electromechanical Role of the stator Assembly in LG Motor Systems
- how the AJB73816015 Lg Stator Assembly Replacement, Fits Many Interfaces with the Rotor, Hall sensors and Drive Electronics
- Common Failure Modes and Diagnostic Symptoms of a Degraded Stator Assembly
- Compatibility, Model Fitment, Installation Guidelines and Post-Installation Troubleshooting for Stator Replacements
- Q&A
- In Conclusion
Function and Electromechanical Role of the Stator Assembly in LG Motor Systems
AJB73816015 Lg Stator Assembly Replacement, fits Many is the stationary electromagnetic element of LG inverter-driven drum motors that provides the magnetic field necessary to convert electrical input from the drive board into rotational torque. The assembly consists of a laminated iron core, insulated stator windings, led terminals and mounting interfaces; when the inverter applies timed currents to the windings, a rotating magnetic field is produced that interacts with the rotor’s permanent magnets to generate motion. In practical terms, the stator’s electrical characteristics (winding resistance, phase-to-phase balance and insulation-to-ground), mechanical bolt pattern and connector pinout determine compatibility with a specific motor/controller combination rather than the outer housing alone.
- Compatibility checks: mounting pattern, connector pinout, phase count/pole configuration, and measured winding resistance.
- Common failure indicators: humming with no rotation, high current draw, burnt odor or visible insulation damage, and phase imbalance on resistance testing.
- Installation considerations: maintain correct rotor clearance, torque mounting fasteners to spec, and ensure electrical polarity/phase mapping matches the drive.
When replacing a stator, technicians verify compatibility by comparing the part number, physical dimensions and electrical measurements to the original: a multimeter will confirm phase-to-phase resistance and check for shorts to chassis, while a visual inspection confirms intact insulation and connector integrity.In service situations-such as a motor that hums but does not turn or throws motor fault codes after overheating-the stator is commonly inspected for burnt windings or shorted laminations; if the windings are open, shorted, or show leakage to ground, the AJB73816015 unit is a direct mechanical/electrical replacement option for many LG assemblies provided those measurements and mounting details match the existing unit.
| Item | Description |
|---|---|
| Part number | AJB73816015 – stator winding assembly for select LG inverter motors |
| Function | Stationary coil assembly that generates the rotating magnetic field for rotor interaction |
| Key checks | Mounting pattern, connector pinout, winding resistance, insulation-to-ground |
How the AJB73816015 Lg Stator Assembly Replacement, Fits Many Interfaces with the Rotor, Hall Sensors and Drive Electronics
The AJB73816015 Lg Stator Assembly Replacement, Fits many is a stationary winding and mounting assembly engineered to interface mechanically and electrically with a range of LG brushless motor rotors, integrated Hall sensor arrays, and the external drive electronics.The stator defines the magnetic circuit and winding geometry that determines phase-to-phase resistance, inductance, and the axial air gap to the rotor; these parameters control torque production, cogging, and thermal dissipation. Mechanically, the replacement stator must match the rotor shaft clearance, bolt pattern and axial location so the rotor’s pole alignment and the Hall sensor pick-up positions remain correct for the original commutation timing.
Compatibility with the rotor, Hall sensors and drive electronics is confirmed by checking a few practical interfaces: the stator’s connector pinout and coil wiring must match the drive’s expected phase and sensor signals, the Hall sensor timing window must fall within the drive’s commutation timing tolerance, and the air gap and mounting tolerances must preserve the original magnetic coupling. In practice technicians validate a replacement by measuring phase resistance and insulation, observing Hall outputs with an oscilloscope while rotating the rotor by hand, and confirming that the drive recognizes the three-phase sequence; common symptoms of mismatch include excessive vibration, reduced torque, or failure to spin. Typical compatibility checks include:
- Mechanical fit: bolt pattern, shaft clearance, and axial location
- electrical fit: connector pinout and phase wiring continuity
- Sensory fit: Hall sensor signal levels and timing relative to rotor poles
- Performance checks: phase resistance, insulation, and no-load spin behavior
| Item | Description |
|---|---|
| Mounting interface | Bolt pattern, spacer thickness and shaft clearance must match rotor assembly |
| Electrical interface | Phase leads and sensor connector pinout compatible with the original drive |
| Typical coil resistance | Measure and compare against service manual or donor unit for expected range |
| Hall sensor timing | Analog/digital pulses that align with rotor pole passage within drive tolerance |
Common Failure Modes and Diagnostic Symptoms of a Degraded Stator Assembly
The stator assembly forms the stationary electromagnetic field that the rotor interacts with; failures manifest as incorrect magnetic flux, uneven torque, or electrical leakage. The AJB73816015 Lg Stator Assembly Replacement, Fits Many is a direct-replacement stator used in a range of compatible LG motors and retains the mounting pattern and connector interfaces found on original equipment, but technicians must confirm coil configuration and connector pinout before installation.Common mechanical and electrical failure modes include shorted or open windings, delamination or rusted laminations that change the magnetic path, and damaged connector contacts that cause intermittent phase supply-each of these alters motor behavior rather than presenting as a single fault code on the appliance controller.
- Intermittent or no rotation under load while the control signals appear correct
- Excessive humming, vibration, or oscillation during start or run
- Burnt odor, visible charring, or discolored windings indicating overheating
- Tripped thermal protection or high current draw measured at the motor leads
- One or more windings showing open circuit or short-to-ground on multimeter/megohmmeter
To diagnose a degraded stator, combine visual inspection with electrical measurements and a load test: inspect for burned enamel, insulation breakdown, and loose laminations; use a multimeter to verify continuity between phase leads and a megohmmeter to check insulation to core/ground; and, where possible, measure current and motor voltage during a controlled run to detect imbalances. In practical workshop work, a stator that shows low insulation resistance or uneven resistance between phase leads should be replaced rather than repaired, because rewinding or partial repair often alters motor balance and thermal characteristics; also verify controller outputs and motor harness integrity to avoid misattributing a drive or wiring fault to the stator.
| Item | Description |
|---|---|
| Winding continuity | Low resistance between corresponding phase leads; open indicates broken winding |
| Insulation resistance | High resistance to core/ground expected; low readings indicate insulation failure |
| Visual condition | Look for discoloration, melted enamel, or loose laminations that change flux path |
Compatibility, Model Fitment, Installation Guidelines and Post-Installation Troubleshooting for Stator replacements
AJB73816015 Lg Stator Assembly Replacement, Fits Many is the stationary winding and mounting flange used in a range of LG inverter-driven motor assemblies. Compatibility depends on matching the electrical interface (connector pinout and phase-to-phase resistance), the mechanical interface (bolt pattern, inner diameter and shaft/rotor clearance), and any sensor or shield features used by the original motor. Technicians should verify the printed part number on the old stator or compare the plug, mounting holes and winding count against the service manual; physically measuring the connector type and phase resistances with a multimeter provides a reliable confirmation when a service manual is not available. Mismatches commonly seen in field repairs include incorrect connector pinouts, insufficient rotor/stator air gap causing rubbing, or different winding characteristics that change motor current and control behavior.
Installation requires clean mating surfaces, correct alignment and secure strain relief for the harness; do not compress or nick the stator windings during assembly. After installing the stator, verify free rotation of the rotor by hand, measure phase-to-phase resistances and insulation to chassis, and run a controlled power-up while monitoring current and temperature. If symptoms appear after installation, use these checks to isolate the fault: examine connectors for bent pins, confirm the air gap and concentricity, measure each phase for shorted turns (low or unequal resistance) and inspect the inverter/motor controller for fault codes.Common practical fixes include reseating or replacing a damaged harness connector, correcting bolt torque and alignment, or replacing a stator that shows insulation breakdown or shorted windings.
- No rotation with humming – check connector continuity, phase resistance and rotor clearance.
- Intermittent spin or overheating – inspect for shorted turns and verify proper air gap/concentricity.
- Excessive vibration or noise – confirm mounting pattern, bolt torque and absence of rotor rubbing.
- Controller error codes after replacement – confirm pinout, sensor wiring and phase balance.
| Item | Description |
|---|---|
| Connector type | Match pin count, shape and pin assignment to the original harness before powering the motor. |
| Mounting pattern | Verify bolt circle diameter and flange thickness to maintain concentricity and proper torque. |
| Phase resistance | Measure phase-to-phase resistance to detect shorted turns or winding differences that affect controller tuning. |
| Air gap | Ensure consistent radial clearance between rotor and stator to prevent rubbing and maintain magnetic flux characteristics. |
Q&A
What is the AJB73816015 stator assembly and what does ”Fits many” meen?
The AJB73816015 is the stator assembly used in LG direct‑drive motor systems (the stationary coil pack that the rotor spins around). “Fits Many” means the same stator assembly is used across a number of LG washer models and motor families. Always confirm fitment for your appliance by checking the washer model number against the part cross‑reference from LG or an authorized parts supplier before ordering.
What symptoms indicate the stator is failing and needs replacement?
Common signs of a failing stator include the washer not spinning or only humming, intermittent spin or drive operation, a strong burnt electrical odor, excessive motor heat, and motor/drive related fault indications on the control panel. Visual signs include burned or discolored windings or water/contaminant damage to the coils.
How can I test the stator to be sure it is bad before replacing it?
With the motor disconnected from the washer and power removed, use a multimeter to check continuity between the motor phase terminals. For a 3‑phase stator you should see low, similar resistance values between each phase pair and no continuity from any winding to the stator core (ground). An open winding or a winding shorted to ground indicates a bad stator. If available, an insulation resistance (megger) test can further confirm coil insulation failure. Also inspect visually for burned windings or moisture damage.
Can I replace the AJB73816015 myself and what tools/steps are required?
Technically yes if you have mechanical skill and the right tools: screwdrivers, socket/Torx set, motor puller or press for rotor removal, bearing tools if removing the hub, and a multimeter. basic steps: disconnect power, remove washer cabinet and drum as needed, remove motor assembly, separate rotor from stator (careful of strong magnets), unbolt the stator and disconnect the harness, fit the new stator, reassemble, and verify electrical connections and air gap. As the job can require pulling the rotor and pressing bearings, many diyers prefer a trained technician.
Do I need to replace other parts when changing the stator?
It’s good practice to inspect and often replace wear items while the motor/drum is apart: motor bearings/seal, rotor hub components, seals, and any damaged harness or connectors. If the rotor magnets or bearings show damage or excessive wear, replace those as well. Replacing related parts while you have access avoids future disassembly.
Are AJB73816015 parts OEM or aftermarket, and does that matter?
The AJB73816015 designation is used to identify a specific replacement stator; parts sold under that number can be OEM (LG) or aftermarket. OEM parts carry the advantage of guaranteed fit and manufacturer testing. Quality of aftermarket stators varies-buy from reputable suppliers, check warranty and return policies, and verify part compatibility with your washer model.
How long does the replacement usually take and is any calibration required afterward?
An experienced technician can typically complete stator replacement and reassembly in about 1-3 hours depending on model and shop equipment; a DIYer should allow more time. After reinstallation,run the washer through a diagnostic or motor test cycle (refer to the service manual) to confirm correct rotation,speed and absence of fault codes. Some LG models may require a motor relearn or diagnostic verification procedure to restore proper operation.
What safety precautions and common pitfalls should I be aware of?
Always disconnect mains power before starting work. Be careful when separating and handling the rotor – strong magnets can pinch fingers and attract metal debris. Do not damage the stator windings or insulation, and keep contaminants and moisture away from coils. Make sure wiring connectors are correctly reattached and secure stator mounting bolts to manufacturer specs. If you’re unsure at any step, hire a qualified appliance technician to avoid further damage or safety risks.
to sum up
The AJB73816015 Lg Stator Assembly Replacement, Fits Many serves a central role in restoring the electromagnetic function of washing machine motors and similar appliances. As a core rotating component, a properly functioning stator assembly ensures efficient motor operation, reduces electrical strain, and helps maintain overall appliance performance and longevity. Because this part is compatible with numerous models, it is a practical option for repairing devices where the original stator has failed or degraded.
Accurate diagnosis and timely replacement are essential when stator problems are suspected. Identifying symptoms such as unusual noises,intermittent operation,overheating,or a complete loss of motor function helps prevent secondary damage to other components. Professional inspection or using manufacturer-recommended diagnostic procedures improves the likelihood of selecting the correct AJB73816015 replacement and ensures that installation and electrical connections meet safety and performance standards. After replacement, functional testing verifies that the appliance operates within expected parameters.
When chosen and installed appropriately, the AJB73816015 Lg Stator Assembly Replacement, Fits Many can be a cost-effective solution to return an appliance to reliable service.Prioritizing proper diagnosis, compatibility verification, and qualified installation minimizes the risk of recurrence and contributes to safer, longer-lasting operation.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
