DA82-02695A Samsung A/S Assembly ICE;FS DA92 00592B 120V OEM
DA82-02695A Samsung A/S Assembly ICE;FS DA92 00592B 120V OEM is an electromechanical ice-maker assembly designed for use in Samsung refrigeration units. The assembly typically combines a motorized ejector, fill mechanism (solenoid or valve interface), internal control circuitry and sensors into a single service-replaceable module rated for 120 volts. As an OEM replacement part, its form factor, connectors and mounting points are intended to match factory specifications for compatible freezer compartments.
Inside the appliance, the ice-maker assembly is responsible for metering and filling the ice mold, initiating harvest and ejection cycles, and communicating status to the refrigerator’s main control board.It interfaces with the water supply system (via a fill valve), the refrigerator control electronics (through a harness connector providing line power and control signals), and temperature sensing elements that determine freeze and harvest timing. Proper operation of this assembly is therefore integral to coordinated interactions between hydraulic, electrical and thermal sub-systems in the freezer.
In the article that follows, readers will find a technical examination of the part’s function and electrical/mechanical interfaces, guidance on model compatibility and identification, typical failure modes and observable symptoms, and a structured approach to troubleshooting without making safety-critical assumptions. Replacement considerations such as matching voltage, connector pinouts, mounting alignment and basic safety precautions will also be discussed so technicians, engineers and informed appliance owners can assess repairs and parts sourcing in a methodical manner.
Table of Contents
- Function and Role of the DA82-02695A Ice Assembly in Refrigerator Ice-Making and Defrost Systems
- How the DA82-02695A Samsung A/S Assembly ICE;FS DA92 00592B 120V OEM Works Inside the appliance
- Common Failure Symptoms, Electrical Faults and Mechanical Wear Indicators for the Ice Assembly
- Compatibility with Samsung models, Replacement Considerations, Installation Steps and Troubleshooting Procedures
- Q&A
- Concluding Remarks
Function and Role of the DA82-02695A Ice Assembly in Refrigerator Ice-Making and Defrost Systems
the DA82-02695A Samsung A/S Assembly ICE;FS DA92 00592B 120V OEM is an integrated ice-maker module that combines the ice mold, harvest heater, fill-valve actuator, ejector mechanism, and temperature sensing elements into a single service-replacement unit. During a normal ice cycle the assembly sequences a water fill, freeze interval, heater-driven harvest and mechanical ejection; the factory 120V heater is used to warm the mold just enough to release cubes without melting them. The assembly’s connectors and mounting points match the DA92 00592B harness and chassis interfaces on compatible Samsung freezers, so correct voltage rating, pinout and sensor type are the key compatibility factors for a direct OEM swap.
Even though the ice assembly is not the primary defrost heater for the evaporator,its operation depends on proper defrost performance and ambient freezer temperature. A failed defrost cycle or blocked drain can cause frost buildup that freezes the fill tube or prevents proper thermal sensing, which in turn leads to no-fill, incomplete harvest, or harvest failure. For practical troubleshooting, check the ice mold thermostat/thermistor continuity and the harvest heater resistance, verify the water inlet solenoid operation, and confirm that the freezer’s defrost system effectively clears evaporator frost to maintain the temperature envelope the ice-maker expects.
- Common symptoms: no ice production, cubes stuck in mold, continuous water flow, or partial ejection.
- key checks: harvest heater resistance, mold thermostat continuity, water valve voltage during fill, and connector/pin alignment with DA92 00592B harness.
- Compatibility notes: confirm 120V heater rating and wiring harness match before replacing with the OEM assembly.
| Item | Description |
|---|---|
| Main functions | Water fill, freeze timing, harvest heater activation, cube ejection, and mold temperature sensing. |
| Voltage / interface | 120V harvest heater; connector and pinout designed to mate with DA92 00592B harness on compatible Samsung models. |
| Practical impact | Interacts with freezer defrost and temperature control; defrost failures commonly manifest as ice-maker faults rather than internal ice-maker electrical failures. |
How the DA82-02695A Samsung A/S Assembly ICE;FS DA92 00592B 120V OEM Works Inside the Appliance
The DA82-02695A Samsung A/S Assembly ICE;FS DA92 00592B 120V OEM is the factory ice-maker subassembly designed to replace the ice-making mechanism in compatible Samsung freezer compartments. This unit combines the ice mold, motor-driven ejector, fill cup, heater element, and embedded sensors into a single mechanical and electrical package that plugs into the refrigerator harness via the DA92-00592B connector. The assembly expects a line-driven harvest circuit in some models, so you will frequently enough see ~120V present at the motor/heater terminals during the harvest/eject phase while the main control board sequences the fill and freeze cycles.
Operation typically follows a controlled sequence: the control board energizes the ejector motor to expel ice, briefly applies the mold heater to release frozen cubes, and then actuates the water fill mechanism to refill the mold. Troubleshooting focuses on verifying motor rotation, heater continuity, proper timing from the control board, and correct connector pinout; measuring voltage at the harness and checking continuity of the internal thermostat are practical diagnostics. Replacement compatibility depends on matching mounting points, connector pin assignments, and heater voltage; using an assembly with mismatched voltage or pinout can leave the mechanism nonfunctional even if it physically fits.
- No ice production while compressor and evaporator are cold (possible motor or fill fault)
- Partial or uneven fills (fill cup or valve timing issue)
- Ice bridged to mold or poor ejection (heater or ejector motor failure)
- Audible motor movement without ice release (mechanical jam or heater failure)
| Item | Description |
|---|---|
| Part number | DA82-02695A (assembly),references DA92-00592B harness |
| Voltage | Operates with a ~120V harvest circuit on supported models |
| Key functions | Ice mold,ejector motor,mold heater,fill cup interface,sensors |
| Common failure modes | Motor/ejector wear,heater open circuit,connector pin corrosion,sensor faults |
| Compatibility note | Must match mechanical mounting,connector pinout,and heater voltage to be a functional replacement |
Common Failure Symptoms,Electrical Faults and Mechanical Wear indicators for the Ice Assembly
The ice assembly integrates the ice-maker motor/geartrain,harvest heater,water-fill solenoid,and temperature sensing elements to control ice production and ejection. The DA82-02695A Samsung A/S Assembly ICE;FS DA92 00592B 120V OEM is supplied as a 120V OEM assembly that replaces the combined electromechanical subassembly found in compatible Samsung freezer-ice systems. Faults in any of these subcomponents produce distinct operational behaviors: a failed harvest heater will prevent ice release during the harvest cycle, a seized geartrain or worn bushing will cause motor current draw without rotation, and a failed thermistor or open sensor circuit will produce incorrect cycle timing or continuous fill events.
- No ice production or intermittent harvest-possible open heater, failed motor, or bad thermistor.
- Ice present but not ejected or crushed-signs of mechanical jam, stripped gear teeth, or worn auger/bushing.
- Continuous water fill or overflow-sticking water inlet valve or failed fill sensor/switch.
- Loud grinding or high current draw-motor winding issues, seized shaft, or degraded gears.
- Erratic cycles or no control response-corroded connectors, broken harness wires, or control voltage absent.
Diagnose failures with basic electrical and mechanical checks: verify 120 VAC at the assembly connector during the harvest and fill commands, confirm heater and motor windings show continuity (not open) and are not shorted to ground, and verify the thermistor exhibits temperature-dependent resistance (NTC behavior). Physically inspect for wear: excessive end play in the motor shaft,chipped/stripped gear teeth,melted or deformed heater surfaces,and any ice-chute damage that can cause jams. For practical troubleshooting, note that a motor that hums but does not rotate usually indicates mechanical seizure or stripped internal gears, while an assembly that receives correct control voltage yet fails to operate points to a mechanical or internal electrical open condition rather than a system control fault.
| Item | description |
|---|---|
| Heater | Opens or shorts -> no harvest; check continuity and insulation to chassis. |
| Motor/Geartrain | High current or no rotation -> worn gears, seized shaft, or motor winding fault. |
| Thermistor/Sensor | Incorrect resistance curve -> wrong cycle timing or missed harvest; compare resistance at two temperatures. |
| Water Inlet valve | Sticks open -> overfill; fails to open -> no water/ice. |
| Connectors/harness | Corrosion or loose pins -> intermittent operation and false faults. |
Compatibility with Samsung Models, Replacement Considerations, Installation Steps and Troubleshooting Procedures
The DA82-02695A Samsung A/S Assembly ICE;FS DA92 00592B 120V OEM is an integrated ice-making assembly that combines the ice mold, ejector mechanism, water-fill interface, and temperature sensing elements. In operation the assembly cycles a thermally or electronically timed harvest,actuates the ejector motor or bi-metal arm to release ice,and commands the water fill solenoid; these functions are coordinated through a multi-pin harness that communicates with the refrigerator’s main control board. Compatibility is determined primarily by mechanical mounting points, harness pinout and voltage (this unit is specified for 120V systems), and the control logic expected by the chassis; technicians should compare the assembly’s connector type and pin assignments against the appliance wiring diagram before confirming a direct replacement, as DA92 family revisions can change connector orientation or add sensor lines that affect interchangeability.
- Power off and unplug the appliance before beginning work to avoid electrical hazard.
- Remove inner door liners or ice compartment trim to access mounting fasteners and harness connections.
- Label and detach the wiring harness and water line; inspect seals and the solenoid for mineral build-up before installing the replacement.
- Mount the replacement assembly so the ejector aligns with the ice box, reconnect the harness and water supply, then restore power and initiate a manual harvest/test cycle.
- If the assembly fails to operate,measure supply voltage at the harness,check continuity of the motor and thermostat,and confirm the control board provides the expected drive signals.
Troubleshooting typically follows electrical verification and mechanical inspection: check for 120V at the input when the control requests a harvest, test the ejector motor and fill solenoid for continuity, and confirm the temperature sensor returns plausible resistance values at typical freezer temperatures. Common symptoms that point to the assembly include no ice production (possible fill-valve or supply issue), continuous running or warm freezer (possible thermostat or sensor fault), and jammed or incomplete eject cycles (mechanical obstruction or motor failure). For practical diagnostics, document measured voltages and resistances and compare them to the refrigerator’s service manual values; replacing the DA82-02695A assembly without confirming control-board outputs or water-supply integrity can led to misdiagnosis and repeated failures.
| Item | Description |
|---|---|
| Voltage | 120V AC input; verify with meter during a commanded harvest cycle |
| Connector | Multi-pin harness-confirm pinout against service diagram before swapping |
| Mounting | Bracket locations must match chassis; small dimensional differences can prevent fit |
| Troubleshooting tests | Measure supply voltage, motor/solenoid continuity, and sensor resistance at temperature |
Q&A
What is the DA82-02695A / DA92-00592B ice assembly and what does it do?
The DA82-02695A (also referenced as DA92-00592B) is an OEM Samsung refrigerator ice maker assembly for 120V systems. It contains the ice-making mechanism: the mold, ejector/drive motor, harvest heater, fill cup/valve interface, and the control module/thermostat that cycles the unit through fill, freeze and harvest stages. Its job is to form ice, sense when ice is ready, eject cubes into the bin, and signal the water valve to refill the mold.
how do I confirm this part is compatible with my Samsung refrigerator?
Check the model number of your Samsung refrigerator (on the tag inside the fresh food compartment or on the cabinet edge) and compare it to the OEM parts list for that model. Also verify the existing ice assembly part number on the unit-many Samsung parts have both DA82-02695A and DA92-00592B cross-references.Confirm the electrical connector, mounting points, and that your appliance uses a 120V ice maker. If in doubt, consult Samsung parts lookup or an authorized parts dealer with your refrigerator model number.
What are common symptoms that this ice assembly is failing or needs replacement?
Typical symptoms include no ice production, partial or small ice cubes, ice maker not cycling (no fill or no harvest), continuous water running into the ice bin, clicking/grinding noises from the ice maker, or visible corrosion/burn marks on the control module. If the ice bin is empty for an extended period and the water valve is known good, the ice assembly is a likely culprit.
How can I safely test the ice assembly to determine if it is defective?
First, disconnect power to the refrigerator.Visually inspect the assembly for damaged wires, broken gears, or burnt electronics. With power restored and using appropriate safety precautions, use a multimeter to check for 120 VAC at the ice maker harness during its expected fill/harvest cycles. You can also check continuity of the heater and motor windings with the unit powered off.For functional testing, many techs initiate a diagnostic or manually advance the ice maker through a cycle (consult the model’s service manual). If you’re not comfortable working with mains voltage or live testing, engage a qualified appliance technician.
what are the basic steps and safety precautions to replace this ice maker assembly?
Turn off and unplug the refrigerator and shut off the water supply. Remove the ice bin, disconnect the harness and water line (if applicable), and remove the mounting screws holding the assembly.Install the new assembly by reversing removal: mount, connect wiring harness and water line, restore water supply and power. Run a test cycle and check for proper fill and harvesting and for leaks. Always avoid touching live electrical connections, and if the harness is clipped under insulation or shrink tubing, take care when disconnecting.
Is this part 120V and will it work in countries with different mains voltages?
Yes - this particular OEM assembly is designed for 120V systems (typical in the U.S. and Canada).It is not suitable for countries with different mains voltages without appropriate transformers or region-specific components.Using the wrong mains voltage may damage the unit or create a safety hazard. Always use the version specified for your region and refrigerator model.
What are common causes that lead to failure of the ice assembly?
Common causes include: clogged or frozen fill tubes (restricted water flow), failing water inlet valves, mechanical wear of gears or motor, failed harvest heater or thermostat, corrosion from leakage, and electrical damage from power surges. Poor maintenance such as not replacing water filters or allowing the freezer temperature to be too warm/too cold can accelerate problems.
Should I buy OEM DA82-02695A/DA92-00592B or an aftermarket replacement?
OEM parts (like DA82-02695A / DA92-00592B) are made to the original equipment specifications and usually provide the most reliable fit and function and preserve any remaining warranty.Aftermarket parts can be less expensive and sometimes compatible, but quality and fit vary. If you want guaranteed compatibility and performance, use the OEM part and purchase from an authorized dealer or Samsung parts supplier.
Concluding Remarks
The DA82-02695A Samsung A/S Assembly ICE;FS DA92-00592B 120V OEM serves as a dedicated component within compatible Samsung refrigeration systems, contributing to the reliable operation of the ice-making and related assembly functions. As an OEM 120V assembly, it is designed to meet the original equipment specifications for fit, electrical compatibility, and performance, helping to maintain consistent ice production and the overall efficiency of the freezer or ice-making subsystem.
Because symptoms such as intermittent ice production, electrical faults, or mechanical failures can have multiple causes, proper diagnosis is essential before replacing the assembly. Verifying voltage, inspecting connectors and harnesses, and following the manufacturer’s troubleshooting procedures will help determine whether the DA82-02695A / DA92-00592B assembly is the root cause.Where replacement is required, using the correct OEM part and adhering to recommended installation practices reduces the risk of recurring issues and ensures safe operation.
In professional and consumer servicing contexts, prioritizing accurate diagnosis and the use of compatible OEM components supports long-term reliability and safety. When in doubt, consult the equipment’s service documentation or engage a qualified technician to confirm that the DA82-02695A Samsung A/S Assembly ICE;FS DA92-00592B 120V OEM is the appropriate solution for the identified fault and is installed according to the manufacturer’s guidelines.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
