DE81-02696A Samsung SVC IGNITER Assembly KIT SINGLE;76482 001 ER OEM is an OEM igniter assembly designed for use in Samsung gas appliances. It is a field-replaceable ignition component that contains the electrical and mechanical parts required to initiate combustion at a gas burner, and it is supplied to match the original equipment specifications and mounting interfaces of the referenced appliance models.
Within an appliance,the igniter assembly provides the ignition energy-either as a high-voltage spark or as a hot-surface element depending on the appliance design-and interfaces directly with the appliance control module,gas valve,wiring harness,and any flame-sensing or safety interlock devices. proper operation of the igniter is essential for timely burner ignition, for preventing unburned gas accumulation, and for allowing the control system to confirm a sustained flame; it thus plays a central role in both normal heating cycles and the appliance’s safety logic.
This article will explain the DE81-02696A igniter’s function and typical installation contexts,outline the appliance models and locations where the part is commonly used,and describe common failure symptoms and diagnostic checks a technician or owner can perform. It will also cover compatibility and part-number considerations,basic troubleshooting steps (visual,electrical,and control-signal checks),and practical replacement considerations to ensure safe,reliable restoration of ignition performance.
Table of Contents
- functional Role and Operating Parameters of the Igniter Assembly
- How the DE81-02696A Samsung SVC IGNITER Assembly KIT SINGLE;76482 001 ER OEM Integrates and Operates Within the Appliance
- Common Failure Modes and Observable symptoms for the Igniter Assembly
- Replacement Considerations, Model Compatibility, and Installation Procedures
- Q&A
- Key Takeaways
Functional Role and Operating Parameters of the Igniter Assembly
The DE81-02696A Samsung SVC IGNITER Assembly KIT SINGLE;76482 001 ER OEM serves as the active ignition element in compatible Samsung gas ovens and ranges. This assembly converts electrical energy into heat at the burner manifold: when the oven control calls for heat the control applies voltage to the igniter, the element heats to its operating temperature and the gas safety valve is allowed to open so a stable flame can be established. The part is supplied as a field-replaceable module with the OEM mounting bracket and connector geometry, so fitment and connector compatibility are primary concerns when replacing the component on a specific appliance model.
- Function: provides the required thermal energy to trigger the gas safety valve and initiate combustion
- Electrical interface: two‑wire connector to the oven control that supplies mains-level voltage during the ignition cycle
- Behavior: draws current until the element reaches ignition temperature; insufficient current or broken filament prevents valve actuation
- Diagnostics: continuity/resistance check, observe warm-up time and current draw, inspect connector and mounting for heat damage
- Compatibility: match part number and connector/bracket orientation to ensure correct manifold sealing and electrical mating
For practical service work, technicians should verify correct part number and physical fit before installation and perform simple bench checks such as continuity and visual warm-up testing in situ. Typical field symptoms that point to a failing igniter are prolonged warm-up, repeated clicking without flame, or a complete failure to light; these indicate either an open or high-resistance element, damaged insulation, or degraded mechanical mounting. When replacing the unit follow safe procedures: disconnect gas and electrical power, preserve the OEM gasket/seal orientation to avoid leaks, and confirm normal ignition sequence after installation by monitoring element warm-up and valve operation.
| Item | Description |
|---|---|
| Warm-up behavior | Element should glow and reach operating temperature within the expected cycle time so the control will energize the gas valve. |
| Service checks | Check continuity, inspect connector pins, verify mounting/gasket integrity, and observe current draw during ignition cycle. |
| Fitment | Ensure the bracket, connector type, and part number match the appliance model to maintain seal and electrical compatibility. |
How the DE81-02696A Samsung SVC IGNITER Assembly KIT SINGLE;76482 001 ER OEM Integrates and Operates Within the appliance
The DE81-02696A Samsung SVC IGNITER Assembly KIT SINGLE;76482 001 ER OEM is a glow-type igniter assembly designed to produce the thermal energy needed to ignite gas in compatible Samsung appliances. In normal operation the control board energizes the igniter circuit, the ceramic or metal-sheathed element heats to a red‑hot condition, and the gas valve is then allowed to open; a flame sensing element or the control’s feedback loop confirms the flame and the system transitions to steady-state heating. The assembly interfaces directly with the appliance’s control module, gas valve, and safety thermostats, and it typically replaces the factory part without requiring modifications to the mounting points or basic wiring harness when the listed compatibility is observed.
- Common failure symptoms: no heat, long ignition delay, or repeated ignition cycles before flame establishment.
- Installation checks: verify connector type and pin-out, confirm mounting orientation and clearance from burner components.
- Diagnostic cues: visual glow during start, voltage present at the harness during call for heat, and continuity across the igniter element.
Operationally, the igniter functions as the initial stage in the appliance’s ignition sequence: the control applies power to the igniter, the element reaches ignition temperature, the gas valve opens, and a flame sensor or control timing confirms accomplished ignition before the igniter current is reduced or cut. For field service, perform a resistance check to determine if the element has continuity and observe whether the control supplies voltage during a heat call; if the igniter shows no visible glow despite proper voltage, the element has likely failed. When selecting this DE81-02696A assembly for replacement, match the part number, harness connector style, and mounting bracket to the appliance model to ensure reliable integration and to avoid issues with clearance, sensor alignment, or control timing.
| Item | Description |
|---|---|
| Function | Provides heat to ignite gas by heating a glow element until the gas valve is actuated. |
| Typical symptom | no heat, extended ignition time, or repeated ignition attempts. |
| Connector | Appliance-specific multi-pin harness; confirm pin-out before installation. |
| Integration | Works with control board ignition relay, gas valve, and flame sensing circuit; requires correct mounting and alignment. |
Common Failure Modes and observable Symptoms for the Igniter Assembly
The DE81-02696A samsung SVC IGNITER Assembly KIT SINGLE;76482 001 ER OEM performs the mechanical and electrical function of creating the ignition energy (spark or hot-surface heat depending on design) at the burner or oven chamber and must match the original connector, lead length, and electrode geometry to operate reliably. Typical failure modes include open or high-resistance circuits caused by internal element degradation, electrode erosion or misalignment, cracked ceramic insulation, corrosion at terminals, and contamination by grease or carbon deposits. These faults change the expected electrical behavior (loss of continuity, abnormal current draw, or erratic sparking) and can be confirmed by visual inspection and basic electrical tests referenced in the appliance service manual; verify model compatibility before replacement to ensure correct mounting, electrode spacing, and connector polarity for the specific Samsung range or oven model.
- No ignition or continuous clicking when the control requests flame (open circuit or valve/igniter timing mismatch).
- Delayed ignition, popping, or intermittent flames due to increased element resistance or electrode contamination.
- Visible damage-cracked ceramic, burned wiring, soot or carbon tracking-indicating insulation breakdown or arcing.
- Electrical test failures: no continuity or out-of-spec resistance on an ohmmeter, or erratic spark during live testing.
For practical diagnosis, isolate electrical power and gas supply before inspection. Begin with a visual check for physical damage and correct electrode positioning, then test for continuity and stable resistance with a multimeter; consult the service manual for acceptable resistance ranges and expected waveform characteristics if using an oscilloscope. Examples: a burner that clicks repeatedly but never lights often points to a failed igniter or a stuck gas valve, whereas a unit that lights but then goes out may indicate weak ignition energy from a partially degraded element or a misaligned electrode. Replacing the igniter assembly with the correct OEM unit typically resolves failures caused by element or insulation degradation, but intermittent or control-related faults require correlated checks of the gas valve, wiring harness, and control module.
| Item | Description |
|---|---|
| Open circuit on continuity test | No continuity measured across the igniter-element has failed and assembly needs replacement. |
| Carbon/soot buildup | Intermittent or delayed ignition; cleaning or replacement required depending on severity and electrode wear. |
| Cracked ceramic or burned lead | Visible insulation damage causes arcing and unreliable ignition; replace assembly and inspect wiring for collateral damage. |
Replacement Considerations,Model Compatibility,and Installation Procedures
the DE81-02696A Samsung SVC IGNITER Assembly KIT SINGLE;76482 001 ER OEM is an OEM replacement igniter assembly designed to restore reliable ignition and flame initiation in compatible Samsung gas ranges and ovens. This assembly performs the primary task of initiating combustion by either heating to a high temperature (hot surface igniter behavior) or presenting an electrode for spark ignition, depending on the model request. Functionally, the igniter must reach its operating condition in the correct time window to allow the gas valve to open and the burner to light; if the igniter draws insufficient current or fails to glow/spark, the safety control will inhibit the gas valve and the appliance will not light. Confirming compatibility requires matching the harness connector, mounting footprint, and any integrated flame-sensing elements to the appliance’s service documentation rather than relying only on visual similarity.
replacement considerations focus on mechanical alignment, electrical continuity, and safe handling. Before beginning work, disconnect power and gas to the appliance and verify zero voltage at the appliance terminals. During installation, maintain the original orientation and gap to the burner port so the sensor or electrode is in the designed position for reliable flame detection; transferring any mounting brackets, insulators, or gaskets from the old assembly ensures proper fit. After securing the DE81-02696A and reconnecting the harness, perform an ignition test and observe the ignition time, flame stability, and the flame-sensing response; a persistent long ignition delay or noisy spark indicates either a wiring/connector issue, an incorrect part variant, or a fault elsewhere in the ignition circuit. Conduct a pressure- and leak-check of gas fittings and validate that the control module sees a correct flame signal before returning the appliance to service.
- Basic replacement steps: power/gas off → remove access panel → disconnect igniter connector → remove old assembly → install new assembly with original brackets/gaskets → reconnect and test.
| Item | Description |
|---|---|
| Function | Initiates burner combustion by heating or sparking and provides flame indication to control circuitry. |
| Connector/Mounting | OEM-style harness connector and model-specific bracket; verify pinout and screw locations before install. |
| Common Symptoms | No ignition, long glow time, intermittent lighting, or failure to detect flame. |
Q&A
What is the DE81-02696A samsung SVC IGNITER Assembly KIT SINGLE and what does it do?
This is an OEM replacement igniter assembly used in compatible Samsung gas ranges/ovens/cooktops. Its job is to ignite the burner gas-either by producing a spark (spark electrode) or by heating a hot-surface (glow) element until it ignites the gas-so the appliance can produce a steady flame. ”Single” indicates it replaces one ignition element.
How can I tell if DE81-02696A is compatible with my Samsung appliance?
Verify compatibility by matching your appliance model number (found on the range/oven chassis or behind the door) with the part listing from Samsung or an authorized parts dealer. You can also compare the old part’s number and physical appearance (mounting points, connector type) to the replacement. When in doubt, contact Samsung support or the parts supplier with your appliance model number.
What symptoms indicate the igniter assembly might potentially be bad and needs replacement?
Common signs include: the burner or oven won’t light, long delays between clicking and flame, continuous clicking with no ignition, weak or intermittent flames, or the element does not glow (for hot-surface igniters). If you smell gas and the burner won’t light, stop use and address the issue immediately.
How can I test the igniter before replacing it?
First, disconnect power and gas before any hands-on testing.Visually inspect for cracks, breaks or a burnt element.For a hot-surface (glow) igniter: when powered (by a qualified person) it should visibly glow orange; with power off you can check continuity/resistance with a multimeter-many oven igniters measure in the low tens to a few hundred ohms, but exact values vary by model. For a spark electrode: inspect the electrode tip for breakage or carbon buildup and check that wiring/connectors are intact; sparking tests should be performed only by trained technicians as of the risk of igniting gas. If you’re not pleasant testing electrical components, have a qualified appliance technician perform diagnostics.
Can I install this igniter myself and what tools or steps are required?
Experienced DIYers can frequently enough replace an igniter assembly. Basic tools include a screwdriver or nut driver set, pliers, and possibly a socket set. General steps: disconnect electrical power and shut off gas, remove access panels or oven/cooktop parts to reach the igniter, disconnect the wiring harness, remove mounting hardware, transfer or fit the new assembly, reconnect wiring and reassemble.Do not power the appliance or restore gas until the igniter is properly installed and all panels/guards are back in place.If you’re unsure, hire a qualified technician.
What safety precautions should I follow when handling or replacing this igniter?
Always disconnect electrical power and turn off the gas supply before starting work. Work in a well-ventilated area and do not test ignition with gas on while handling parts. Avoid touching the ceramic or glowing surface of a hot-surface igniter with bare hands (oil from skin can damage it). Wear gloves and eye protection, and ensure all connections are secure before restoring power or gas. If you detect a gas leak, stop and contact a professional immediately.
Is this part an OEM component and is it interchangeable with aftermarket igniters?
DE81-02696A is listed as an OEM Samsung service part. OEM parts are designed to match the original equipment fit and function. Aftermarket parts may be available and sometimes compatible, but interchangeability depends on physical fit, connector type, and electrical characteristics-verify compatibility before choosing a non‑OEM option.
After installing the new igniter, do I need to adjust or calibrate anything if the oven still won’t light?
Typically no calibration is needed after installing an igniter. If the appliance still won’t light, check that wiring connectors are fully seated, mounting and electrode gap (if applicable) are correct, and that the igniter receives power when a burner/oven is commanded to ignite. If wiring and installation are correct but it still fails, the problem may be the spark/ignition module, gas valve, or control board-further diagnostics by a technician will be necessary.
Key Takeaways
The DE81-02696A Samsung SVC IGNITER Assembly KIT SINGLE;76482 001 ER OEM serves as a critical component in compatible Samsung cooking appliances, providing the reliable ignition source required for safe and consistent burner operation. As an OEM assembly, it is designed to meet the manufacturer’s specifications for fit, function, and durability, helping to maintain appliance performance and minimize the risk of ignition-related malfunctions.
Because ignition issues can stem from a range of causes – from wear and component failure to related control or gas-supply problems – proper diagnosis is essential before replacing parts. When testing indicates the igniter assembly is faulty, replacement with the correct OEM kit restores intended operation and reduces the likelihood of recurring issues.For safety and optimal results, follow manufacturer guidance and safety protocols or engage a qualified service technician to confirm the diagnosis and perform the replacement.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
