DA82-02671A Samsung A/S Assembly ICE;DA94 02963C CD 120 OEM is an ice maker assembly used in Samsung refrigerators; it is a modular ice production and dispensing subassembly that includes the ice mold, motor/gear train, ejector mechanism, fill cup, and the associated electrical connector and mounting hardware. As a replaceable OEM assembly, it is intended to fit into the freezer compartment and interface with the refrigerator’s water supply and control electronics, providing the mechanical and electromechanical elements required for automatic ice production.
inside the appliance the assembly coordinates the ice-making cycle by receiving control signals from the refrigerator main control board and by actuating mechanical sequences: filling the mold with water, sensing freeze completion, initiating a harvest or hot-water/heater cycle if present, and ejecting formed ice into the storage bin or dispenser pathway. It interfaces directly with the water inlet valve and supply tubing, the freezer temperature sensing elements or thermistor, the chassis-mounted harness and connector, and-when present-the dispenser mechanism. Proper alignment,sealing,and electrical continuity are notable for reliable operation and for preventing leaks,ice jams,or false cycle conditions.
In this article readers will find a technical overview of the DA82-02671A/DA94-02963C assembly covering how it functions,typical points of compatibility to confirm before replacement,common failure modes and their symptoms (for exmaple no ice production,incomplete fills,continuous water flow,or ice jamming),and step-by-step troubleshooting strategies to isolate electrical,mechanical,and water-supply issues. The piece will also address practical replacement considerations such as verifying OEM part numbers and connector/hardware fit, safe isolation of power and water before service, recommended diagnostic checks, and tips for testing the assembly after installation to ensure correct operation without relying on marketing claims or unsupported performance expectations.
Table of Contents
- Function and Role of the DA82-02671A Ice Assembly in Samsung Cooling and Dispensing systems
- How the DA82-02671A Samsung A/S Assembly ICE;DA94 02963C CD 120 OEM Operates Within Refrigerator Control and Ice-Making Circuits
- Common Failure Symptoms and Diagnostic Tests for Ice-Assembly Malfunctions
- Compatibility, Replacement Considerations, and Installation Procedures for supported Samsung Models
- Q&A
- Concluding Remarks
Function and Role of the DA82-02671A Ice Assembly in Samsung Cooling and Dispensing Systems
The DA82-02671A Samsung A/S Assembly ICE;DA94 02963C CD 120 OEM is the modular ice maker assembly that controls water metering, freeze timing, harvest release and ice ejection inside compatible Samsung refrigerator freezers. Mechanically the assembly contains a fill cup, ejector/auger or arm, motor and gearbox, and a harvest heater or bi-metal thermostat/thermistor; electrically it interfaces with the main control board and the water inlet valve thru a multi-pin harness. When installed correctly, the assembly sequences a fill cycle, allows the water to freeze to the preset dwell time or temperature, applies a harvest heater or actuator to release the ice, and then advances the ejector to deposit cubes into the collection bin; compatibility depends on matching the harness connector, mounting bosses, and control-board cycle expectations rather than on the cosmetic shape of the housing alone.
- Key functional checks: water fill volume and pressure, motor rotation and torque, harvest heater continuity, and thermistor/thermostat response during a forced cycle.
| Item | Description |
|---|---|
| Part numbers | DA82-02671A (primary), cross-referenced DA94-02963C |
| primary function | Controlled metering of water, timed/freezer-temperature-based freezing, harvest release, and ice ejection. |
| installation notes | Verify harness pinout and mounting alignment; confirm water pressure and run a diagnostic/force cycle after replacement. |
In operation, the ice assembly’s timing and sensor feedback directly affect ice quality and dispenser behavior: insufficient fill or short freeze intervals yield small or hollow cubes, while a failed heater or stuck ejector produces no harvest and ice buildup.Practical troubleshooting starts with a service-mode harvest cycle to observe motor and heater function, measuring continuity on the heater and resistance on the thermistor, and confirming the water inlet valve completes a fill in each cycle. For field repairs, technicians should verify that the replacement assembly’s connector, mounting points, and actuator timing match the refrigerator’s control logic; mismatches can cause repeated fills, flooding, or failure to harvest despite or else functioning refrigeration and water supply systems.
how the DA82-02671A Samsung A/S Assembly ICE;DA94 02963C CD 120 OEM Operates Within Refrigerator Control and Ice-Making Circuits
The DA82-02671A Samsung A/S Assembly ICE;DA94 02963C CD 120 OEM is an integrated ice-maker module that interfaces directly with the refrigerator control board to manage the freeze, harvest and fill sequences. The assembly contains the ice mold, drive motor and ejector, a low-temperature sensing device (thermostat or thermistor), and the harvest heater; the control board provides timed power to the motor and heater and monitors the sensing device to sequence the cycle.In operation, the board energizes the motor to advance the ejector, applies power to the heater during the harvest phase to loosen ice from the mold, and actuates the water inlet valve via a separate control circuit to refill the mold. Technicians should view this assembly as both an electromechanical actuator and a sensor endpoint that must present correct continuity and expected temperature feedback to the main control for reliable cycling.
Common failure modes relate to mechanical binding of the ejector, open or shorted heater elements or sensing leads, and connector or harness compatibility issues; replacement requires matching connector pinout and mounting alignment rather than only matching part numbers. For practical diagnosis, verify that the control board is commanding the ice maker during a forced ice-maker cycle and measure for motor/heater continuity and correct impedance of the temperature sensor; if the board supplies expected voltage but the motor/heater do not respond, the fault is internal to the assembly. When replacing the unit, compare the harness connector and mounting brackets to ensure plug-and-play compatibility and inspect for worn gears or ice buildup that can mimic electrical failure.
- Symptoms indicating assembly fault: no harvest, no fill, continuous run, or visible leakage during cycle.
- Useful checks: force-cycle from the main board, continuity checks on motor/heater, and resistance check of the temperature sensor.
- Compatibility note: confirm connector pinout and harness length before assuming interchangeability.
| Item | Description |
|---|---|
| Motor | Drives ejector arms to advance ice and index the mold during cycle |
| Heater | Provides brief heat during harvest to release ice from the mold |
| Thermostat/Thermistor | Reports mold temperature so the control board times freeze and harvest events |
| Connector | Multi-pin interface to the main control for motor, heater, and sensor signals |
Common Failure Symptoms and Diagnostic Tests for Ice-Assembly Malfunctions
The DA82-02671A Samsung A/S Assembly ICE;DA94-02963C CD 120 OEM is an OEM ice-maker assembly that integrates the ice mold, indexing motor/geartrain, harvest heater, and the position/switch sensing used by the refrigerator control board. Functionally, the assembly receives a harvest command from the board, energizes the heater to loosen ice from the mold, and then the motor rotates the ejector arm to deposit cubes into the bin while a fill valve adds water for the next cycle.Compatibility is determined by the connector pinout,harness length,and mounting points – physically similar parts can still have different control signals or switched inputs,so confirm wiring and control logic before substitution. For practical field work, verify the mechanical free-play of the ejector, the integrity of the heater element and its attachment to the mold, and that the position switch/cam closes at the expected index position; these are the most frequent causes of incomplete cycles or no ice production after replacement.
Diagnostic testing should start with non-destructive checks: visual inspection for cracked molds, ice jams, or corrosion at connector pins; manually advancing the cam to confirm the switch actuates; and observing a full factory harvest cycle using the refrigerator’s service mode while measuring presence/absence of drive and heater outputs at the assembly connector. Use a multimeter to confirm continuity (heater and motor coils should not be open) and to check the thermistor/switch behavior across temperature changes (the sensor should change resistance predictably as the mold warms). Below are common symptoms with focused diagnostic actions that technicians use in the field to isolate failures before replacing the DA82-02671A/DA94-02963C assembly.
- No ice produced – verify supply water pressure and inlet valve operation, then confirm the control board issues a harvest command and that the motor receives drive pulses during service-mode harvest.
- Ice stuck in mold or partial harvest – inspect heater element continuity and attachment; check for broken ejector fingers or mechanical binding and manually advance cam to observe switch action.
- Continuous water fill – check the water inlet valve and the assembly’s fill-switch wiring for shorted or stuck contacts.
- Intermittent cycles or noisy operation – measure motor drive continuity and inspect geartrain for stripped teeth or excessive axial play.
| Item | Description |
|---|---|
| Connector / Pinout | Verify motor, heater, sensor/switch, and fill-valve pins against the service schematic; identical housings can have different pin assignments. |
| typical failure points | Open heater element, seized ejector/motor, failed position switch, or clogged water feed; these cause the majority of functional failures. |
| Recommended tests | Service-mode harvest observations, continuity/resistance checks of heater and motor, sensor resistance vs. temperature, and direct actuation checks where safe. |
Compatibility, Replacement Considerations, and installation Procedures for Supported Samsung Models
The DA82-02671A Samsung A/S Assembly ICE;DA94 02963C CD 120 OEM is an integrated ice-maker module that combines the ice mold, ejector mechanism, harvest heater, motor/gear train, and the local switch or sensor used to signal completion of a harvest cycle. its proper function depends on matching mechanical mounting points, harness pinout, and the control-board harvest sequence: the refrigerator control must provide the same timed output and voltage profile so the motor, heater, and fill valve operate in the expected order.Technicians should compare the physical connector, mounting pattern, and sensor locations between the old and replacement assemblies rather than relying solely on model family names; a mismatch in connector pinout or harvest timing is the most common cause of a non-working replacement even when the part appears to fit physically.
Replacement and installation procedures emphasize electrical and water isolation, accurate transfer of brackets and shrouds, and post-install functional checks. Before removing the old unit, shut power and the water supply, document wire positions, and preserve fasteners; after installing the new assembly, verify a correct fill volume, confirm the heater energizes during harvest, and run the refrigerator’s diagnostic harvest/test mode to observe the full sequence.If the assembly does not perform after installation, measure continuity and resistance of the motor and heater, inspect the fill valve operation and inlet tubing for blockages, and confirm the control board supplies the expected outputs-differences in sensor placement or control logic may require a different part or a simple harness adapter.
- Quick checklist: verify part number and harness shape,confirm mounting pattern,isolate power and water,transfer shrouds and fasteners,run diagnostic harvest,test for leaks and continuity.
| Item | Description |
|---|---|
| Motor/gear assembly | Drives ejector to release ice; check for free rotation and motor continuity. |
| harvest heater | Applies heat to loosen cubes; verify expected resistance and activation during harvest. |
| Water inlet interface | Mounting and tubing connection for fill; inspect for proper seating and sealing. |
| switch/sensor | Detects harvest completion or mold position; verify wiring and signal to control board. |
| Mounting/harness | Physical brackets and connector pinout that determine compatibility with the cabinet and control unit. |
Q&A
What is the DA82-02671A (DA94-02963C CD 120 OEM) part?
DA82-02671A is a Samsung OEM ice maker assembly (sometimes cross-referenced or packaged with the DA94-02963C identifier). It is the complete ice-making module used in compatible Samsung freezers and refrigerator-freezers and includes the ice tray, motor/gear assembly and the internal components required to harvest and dispense ice. Use the part number to confirm fit with your refrigerator model before ordering.
How do I know if this is the correct part for my Samsung refrigerator?
Check the refrigerator model number (usually on a sticker inside the fresh food or freezer compartment, or on the cabinet frame). Cross-reference that model number with Samsung parts lists or the vendor’s compatibility chart. also compare the existing ice maker part number printed on the old unit-if it matches DA82-02671A or a listed cross reference such as DA94-02963C, it’s the correct OEM assembly.
What are the common symptoms that indicate the ice maker assembly needs replacement?
Typical signs include: no ice production despite proper freezer temperature and water supply; ice maker motor not cycling; ice tray filled with partial or misshapen cubes; visible physical damage or corrosion; or electrical failures (no continuity in expected circuits). Before replacing, verify water supply, water valve operation, freezer temperature and run the refrigerator’s diagnostics to isolate the ice maker as the fault.
Can I install this ice maker myself and what are the basic installation steps?
Yes, a technician or a confident DIYer can install it. Basic steps: 1) Unplug the refrigerator and turn off the water supply. 2) Remove the old ice maker (remove cover, disconnect wiring harness and disconnect the water line). 3) Install the new assembly in the same position, reconnect the water line and electrical connector. 4) Secure mounting screws and replace any covers. 5) Turn on water and power, then run an ice maker test cycle or wait for the first fill/harvest cycle. always follow the refrigerator service manual and observe safety precautions.
How do I test the replacement to make sure it’s working after installation?
After reconnecting power and water, either use your refrigerator’s service diagnostic mode to run the ice maker test (many Samsung models support an electronic test sequence) or wait for the ice maker to go through a fill and harvest cycle. Check that the fill solenoid (water fill) operates, water fills the tray, and the ejector/motor cycles at harvest. You can also check continuity on heater/thermostat/ motor pins with a multimeter per the service manual.
What troubleshooting steps should I take if the new ice maker still doesn’t make ice?
Verify: 1) Water supply is turned on and not blocked (filter, kinked tubing). 2) Water filter is not clogged and installed correctly. 3) Freezer temperature is cold enough (usually around -18°C/0°F). 4) The water inlet valve is functional (it supplies the ice maker). 5) Electrical connections and harness have proper voltage during the expected cycle (use the fridge’s diagnostic mode or meter). If these check out and the assembly shows no operation, the new unit could be defective or there might potentially be a separate control/board issue.
Are there differences between the OEM DA82-02671A and aftermarket ice maker assemblies?
OEM units are manufactured to Samsung specifications for form-fit and electrical compatibility. Aftermarket assemblies may be less expensive but can differ in fit, wiring, connector type, or component quality. For best reliability and guaranteed fit, OEM (DA82-02671A / DA94-02963C) is recommended; if you use aftermarket, verify compatibility and return policy.
Do these parts come with a warranty and are there any handling or disposal considerations?
Warranty coverage depends on the seller; OEM parts are commonly sold with a limited parts warranty from the reseller or manufacturer-check the vendor’s listing.When handling, shut off power and water to avoid injury. Dispose of the old ice maker assembly per local electronic waste regulations; if it contains refrigerant lines (most ice makers do not),that requires special handling-otherwise place with normal e-waste or follow appliance-disposal rules in your area.
Concluding Remarks
The DA82-02671A Samsung A/S Assembly ICE and DA94-02963C CD 120 OEM are original equipment components designed to support key functions within Samsung refrigeration systems. As OEM parts, they contribute directly to dependable ice production, system control and overall operational stability. Their correct installation and interaction with other appliance subsystems help maintain performance, energy efficiency and user convenience over the life of the unit.
Given their impact on appliance behavior, accurate diagnosis and judicious replacement are essential. Fault isolation should precede any parts replacement to confirm failure and rule out related causes; when replacement is required, using the appropriate OEM component and following manufacturer service procedures or a qualified technician’s guidance helps preserve compatibility, safety and long-term reliability. Proper testing after installation ensures the appliance returns to expected performance and minimizes the risk of repeat issues.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
