DA97-06473B Samsung Assembly CASE ICE ROUTE;GUGGENHEIM A OEM is a molded assembly component used in Samsung refrigerator ice-making and dispensing systems; it functions as teh structural housing and guided pathway that channels ice from the ice maker to the storage bin and dispenser. this assembly typically consists of injection-molded plastic features – such as guide rails, mounting bosses, sensor housings and seal interfaces – that integrate mechanically with the ice maker module, auger or ejector mechanism, and the cabinet openings for the dispenser. As an OEM part, it is intended to match factory tolerances and attachment points for compatible refrigerator models.
inside the appliance the CASE ICE ROUTE serves several interrelated roles: it provides a controlled route to prevent ice jams and bridging,positions sensors and actuators for correct detection and ejection of ice,and forms watertight or insulated interfaces to minimize melting and leakage. It interacts directly with the ice maker assembly (mold and ejector), the auger or motor coupling that advances ice to the dispenser, the ice-level or optical sensors that signal fullness, and nearby seal elements and door switches. Proper alignment, intact mounting features and undamaged channels are important to maintain reliable mechanical operation, correct sensor readings and to avoid mechanical interference with the auger or dispensing mechanism.
in this article readers will find a technical overview of the DA97-06473B assembly including its functional design, typical points of compatibility and model considerations, common failure modes and their symptoms (for example cracking, warping, clogged or misaligned channels, and sensor mounting failures), step-by-step troubleshooting techniques to isolate mechanical versus sensor issues, and practical replacement considerations such as matching part numbers, required tools, mounting hardware, and post-replacement verification procedures.The information is presented to assist technicians, engineers and appliance owners in diagnosing problems, confirming compatibility and performing safe, effective repairs or replacements without promotional or vendor-specific claims.
Table of Contents
- Functional role and mechanical interfaces of the ice-route case in Samsung ice-production systems
- How the DA97-06473B Samsung Assembly CASE ICE ROUTE;GUGGENHEIM A OEM integrates with evaporator, motor and water-feed subsystems
- Common failure symptoms, wear patterns and sensor indicators for the ice-route assembly
- Replacement considerations, model compatibility, stepwise installation and diagnostic troubleshooting procedures
- Q&A
- In Retrospect
Functional role and mechanical interfaces of the ice-route case in Samsung ice-production systems
The DA97-06473B Samsung Assembly CASE ICE ROUTE;GUGGENHEIM A OEM is a molded ice-route housing that controls the path of ice from the ice mold/evaporator to the collection bin and provides precise mechanical interfaces for the ice-maker assembly. Functionally, this case aligns the ice chute, supports the heater/defrost elements or mechanical drop actuator, and contains channels that direct meltwater to the drain. Its primary mechanical interfaces are snap-fit tabs and screw bosses that mate to the freezer liner, a flange that seats against the ice mold, a sensor mounting boss for the ice-level or drop sensor, and contact points for a strip heater or actuator linkage. The part’s geometry and material selection (designed for low thermal conductivity and dimensional stability) maintain clearances required for reliable drop and minimize ice adhesion where the mold separates from the tray.
In service the ice-route case stabilizes the release trajectory of cubes and prevents water or ice from fouling adjacent components; common failure modes are cracked guide rails, deformed mounting bosses, or clogged drainage channels that produce jams or leakage. Technicians should verify that the guide clearance is unobstructed,that sensor and heater interfaces engage without excessive play,and that sealing surfaces are intact before concluding the ice-maker is faulty. Typical inspection/verification items include:
- Secure mounting bosses and undamaged snap-fit tabs
- Clear, unobstructed ice path and drainage channel
- Proper engagement of the ice-level/drop sensor and heater contacts
- Absence of cracks or warping at the chute and mating flanges
| Item | Description |
|---|---|
| Mounting interface | screw bosses and snap tabs that locate the case to the freezer liner and ice mold |
| Guides/chute | Channels that control ice drop trajectory and limit recontact with the mold |
| Sensor/heater bosses | Dedicated bosses for mounting the drop/level sensor and strip heater or actuator linkage |
How the DA97-06473B Samsung Assembly CASE ICE ROUTE;GUGGENHEIM A OEM integrates with evaporator, motor and water-feed subsystems
The DA97-06473B Samsung Assembly CASE ICE ROUTE;GUGGENHEIM A OEM functions as the mechanical and environmental interface that routes frozen product from the evaporator face to the drive/motor assembly and the water-feed points used during formation and harvest cycles. Its molded channels and mounting flanges align with the evaporator plate to control ice drop locations and to minimize air and moisture leaks that accelerate uneven frosting. The case also provides the support and bearing surfaces for the auger or rotor driven by the motor, a sealed path for meltwater to the drain, and defined passages for the water-feed nozzle; correct installation ensures the motor sees only the designed radial and axial loads while the evaporator maintains uniform heat-exchange behavior.
Practically, the assembly affects subsystem compatibility through tolerances at the motor coupling, sensor windows, and water inlet sealing surfaces: an out-of-spec mounting tab or a warped channel will increase motor torque, cause ice bridging, or misdirect water during the fill cycle. Technicians should verify shaft alignment, sensor clearances, and unobstructed drainage when diagnosing intermittent harvest failures or motor overcurrent trips. Common service checks include inspecting the ice-route channel for fracture or plastic flow, confirming that the water-feed nozzle seats into its boss without lateral play, and confirming electrical connector pins align with the motor and any ice-detect sensor; these checks predict whether the DA97-06473B will integrate correctly with the evaporator, motor, and water-feed subsystems.
- Mounting interface: verifies alignment to evaporator and cabinet.
- Motor coupling: checks fit and free rotation under load.
- Ice channel: inspects for obstructions and correct slope.
- water-feed interface: ensures nozzle seating and leak-free delivery.
- sensors/drain: confirms sensor windows and drainage paths are clear.
| Item | Description |
|---|---|
| Mounting tabs | Locate and secure the case to the evaporator housing to control airflow and ice drop points. |
| Motor boss/coupling | Supports motor shaft and transfers torque to auger or rotor; tolerance affects load and noise. |
| water-feed boss | Aligns and seals the water inlet nozzle to prevent spray misdirection and ice bridging. |
| Drain channel | conveys meltwater away from ice formation areas to reduce refreezing and blockage. |
Common failure symptoms, wear patterns and sensor indicators for the ice-route assembly
The DA97-06473B Samsung Assembly CASE ICE ROUTE;GUGGENHEIM A OEM is a molded channel and mounting subassembly that directs ice and condensate away from the icemaker and dispenser while providing mechanical interfaces for ice-level sensing and door seals. In operation this part aligns the ice trough with the auger/dispenser path, supports sensor housings, and resists intermittent thermal cycling; common compatibility is with specific Samsung refrigerator icemaker modules where the assembly’s dimensions, tab locations, and sensor cutouts must match the appliance chassis and harness connectors.Technicians should treat the assembly as both a structural guide and a functional sensor mount-misalignment, deformed flanges, or damaged sensor bosses will directly affect dispensing performance and sensor feedback to the control board.
- Dispense problems: slow, intermittent or jammed ice flow caused by cracks, obstructions, or distorted guide lips.
- Water leaks or freeze-blocking: frost accumulation or melt/refreeze scars along the route indicating insulation or drain issues.
- False level/full signals: damaged or displaced ice-level sensor housings producing continuous or no-actuate readings.
- mechanical wear: broken mounting tabs, abrasion at contact edges, or deformation from impact or improper installation.
Failure symptoms frequently enough present as a combination of mechanical wear and sensor anomalies; for example, a hairline crack at a mounting boss can let warm air enter the route, producing localized frost that jams the auger and triggers a false-full sensor. Practical inspection steps include checking for visible cracks or gouges, verifying that the ice-level sensor is seated and its wiring connector is secure, and assessing whether door or bin alignment has shifted after service or ice jams. When troubleshooting, measure continuity and signal behavior at the sensor connector, clear any debris from the route, and replace the assembly if tabs or sensor mounts are compromised-repairing cracks with adhesives is only a short-term mitigation when structural alignment is still affected.
| Item | Description |
|---|---|
| Cracked guide lip | Leads to redirected ice flow and increased jamming at the auger inlet. |
| Ice-level sensor boss | Wear or breakage causes incorrect level readings or intermittent open/short signals. |
| Mounting tab deformation | Misalignment of the route relative to the dispenser path, causing rubbing and accelerated wear. |
Replacement considerations, model compatibility, stepwise installation and diagnostic troubleshooting procedures
DA97-06473B Samsung Assembly CASE ICE ROUTE;GUGGENHEIM A OEM is the molded ice-route housing that directs ice from the icemaker to the storage bin or dispenser while managing airflow and thermal isolation within the freezer compartment. The component indexes to the freezer liner with snap tabs and screw bosses and often interfaces with the icemaker module, bin actuator and any local heater or thermistor mounting points.proper form and fit of the case preserve the ice-drop geometry; even small warps, cracked tabs, or misaligned seals change ice trajectories, causing bridging, dispensing jams, or false sensor readings that interrupt harvest cycles or cause continuous harvest attempts.
Replacement and troubleshooting require a methodical approach: verify model compatibility against the refrigerator model code and inspect mounting features and connector types before installing a replacement. Basic installation steps are: remove power and the ice bin, unmount the icemaker if necessary, extract the old ice-route case, confirm drain and heater/thermistor locations are unobstructed, seat the new assembly so all bosses engage, secure fasteners, reinstall the icemaker and bin, then power up and run a manual harvest/dispense test.Diagnostic symptoms and quick checks include visible frost bridges or foreign debris in the channel, broken tabs or loose connectors, and heater/thermistor open or out-of-spec readings; remedial actions typically involve reseating or replacing the case, clearing blockages, and verifying heater continuity and thermistor resistance during a controlled defrost or harvest cycle.
- Pre-install checks: match model code, inspect snap tabs and screw boss integrity, verify heater/thermistor mounting points.
- Installation steps: power off, remove bin/icemaker as needed, replace housing, secure fasteners, verify actuator clearance and seal contact.
- Troubleshooting checks: visual inspection for cracks or ice bridging,multimeter test of heater and thermistor,run manual harvest and observe ice drop behavior.
| Item | Description |
|---|---|
| Part number | DA97-06473B – molded ice-route assembly for select Samsung freezers |
| Compatibility | Designed for specific Samsung refrigerator models; confirm model code and mounting boss pattern before replacing |
| Common failure modes | Cracked tabs, warped channel causing ice bridging, blocked drain or misaligned sensor/heater mounts |
| Tools/Checks | Phillips/hex driver, multimeter for continuity and thermistor resistance, visual and thermal inspection for frost buildup |
Q&A
what is the DA97-06473B (Assembly CASE ICE ROUTE; GUGGENHEIM A) part?
DA97-06473B is an OEM Samsung ice-route or ice-chute housing used in certain samsung refrigerators. It is indeed the molded plastic assembly that channels ice from the ice maker/ice bin toward the dispenser or into the ice storage area.“GUGGENHEIM A” is an internal designation tied to that specific molding.
How do I know if this is the correct replacement part for my refrigerator?
Verify the part number printed on the existing plastic housing or on the appliance parts diagram for your refrigerator model. Also check your refrigerator model code (usually on a sticker inside the fridge or on the frame) against Samsung parts listings. If unsure, provide your full model number to a Samsung parts dealer or authorized service center to confirm compatibility.
What are the common symptoms that indicate the ice-route assembly needs replacement?
Typical symptoms include frequent ice jams, ice falling out of alignment into the freezer or dispenser, visible cracks or broken mounting tabs on the housing, water pooling or leaking from the ice chute area, or unusual noises when dispensing ice. If the plastic is warped or damaged it can impede ice movement and will usually need replacement.
Can I replace the DA97-06473B myself, and what tools are required?
Yes, a competent DIYer can usually replace the assembly. Basic tools typically include a Phillips screwdriver and/or Torx driver, and possibly pliers.You must disconnect power to the refrigerator before starting, remove any shelves/ice bin/ice maker components blocking access, unplug the ice maker wiring harness if required, remove fasteners holding the old housing, and then install the new piece and reassemble. If you are not comfortable working on appliances or if the job requires accessing sealed components, contact a qualified technician.
Does the DA97-06473B include seals, screws, or the ice maker module?
Most listings for DA97-06473B refer to the molded plastic ice-route housing only. It may or may not include small mounting hardware or gaskets-that depends on the supplier. It does not include the ice maker electronic module or motor unless explicitly stated.Read the product description carefully or ask the seller which items are included.
Are there any special installation notes or precautions?
Always unplug the refrigerator before servicing. Handle the plastic housing gently to avoid cracking mounting tabs. Make sure mating surfaces and seals are clean and dry to prevent leaks. Reconnect wiring harnesses securely and check ice maker alignment so ice flows freely. After reassembly, allow the unit to run and test ice production and dispensing; observe for leaks or jams.
Is it better to buy OEM DA97-06473B or an aftermarket replacement?
OEM parts like DA97-06473B guarantee proper fit, material compatibility and match the original design. Aftermarket replacements can be less expensive but may have fit or durability differences.For long-term reliability and to maintain factory fit,OEM is recommended-especially for complex assemblies where fit and tolerances matter.
how can I test the ice-route assembly after installation to ensure the problem is resolved?
Reassemble the ice bin/ice maker and restore power. Allow the ice maker to cycle (this may take several hours for new ice), then test by dispensing ice or manually advancing the ice maker (if your model has a test or advance function).Verify there are no jams, ice flows smoothly through the route, and no water leaks. If problems persist, recheck alignment, fasteners and wiring, or consult a technician.
In Retrospect
The DA97-06473B Samsung Assembly CASE ICE ROUTE;GUGGENHEIM A OEM serves as a critical component within compatible refrigerators by guiding and protecting the pathway through which ice is transported from the ice maker to the dispenser or storage bin. Its proper fit, seals and internal geometry help prevent ice jams, minimize leaks and reduce undue stress on adjacent mechanisms, contributing to consistent dispensing performance, temperature control and overall appliance reliability.
Because symptoms such as irregular dispensing, unusual noises, leaking or ice buildup can arise from multiple causes, accurate diagnosis is essential to determine whether the assembly case is the root issue. When diagnostics indicate the DA97-06473B assembly is worn, cracked or otherwise compromised, replacement with the correct OEM part restores intended fit and function, reduces the risk of repeat failures and helps maintain manufacturer specifications. Proper installation and post-repair testing-performed by a qualified technician or according to manufacturer instructions-further ensure safe, lasting operation.
the DA97-06473B Samsung Assembly CASE ICE ROUTE;GUGGENHEIM A OEM plays a defined role in ice management within the refrigerator system, and thoughtful diagnosis followed by timely replacement with the appropriate OEM component supports appliance performance, reliability and longevity.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
