241816602 Frigidaire Refrigerator Motor-AUGER is an electromechanical auger motor assembly designed to drive the helical auger in a refrigerator ice-dispensing system. It is a low-speed, high-torque motor with an integrated gearbox and mounting interface, built to operate in low-temperature freezer environments and to rotate the auger shaft that feeds ice from the ice bin or ice maker to the dispenser chute.
Inside the appliance, the auger motor couples directly to the ice-bin auger and works as part of the ice dispensing subsystem. It receives actuation commands from the dispenser control circuitry and coordinates with door or paddle switches, the ice maker assemblyand any associated clutch or coupling hardware. Mechanically it must resist icing and jammingand electrically it must tolerate the control voltage, pulse signalsand any thermal or current protection provided by the refrigerator control board.
In this article you will learn how the 241816602 auger motor functions, where and how it is typically installedand which refrigerator systems it interfaces with. The discussion covers compatibility considerations (mechanical fit, electrical connector and control signal requirements), common failure symptoms (no dispense, motor hums, intermittent rotation, seizure from ice bridge), practical troubleshooting steps (verify control signals, check continuity and resistance, inspect for mechanical obstructions, test coupler and gearbox)and replacement considerations (matching part numbers and mounting details, verifying torque and shaft orientation, and post‑installation checks). This details is intended to assist technicians, engineersand appliance owners in diagnosing, testingand replacing the component safely and effectively.
Table of Contents
- Functional Role of the Auger Motor in Frigidaire Ice dispenser mechanisms
- How the 241816602 Frigidaire Refrigerator Motor-AUGER Works Inside the Appliance
- Common Failure Symptoms and Diagnostic Indicators of Auger Motor Malfunction
- Replacement Considerations, Compatibility, and Installation Procedures for Auger Motor Assemblies
- Q&A
- In Conclusion
functional Role of the Auger Motor in Frigidaire Ice dispenser Mechanisms
The 241816602 Frigidaire Refrigerator Motor-AUGER provides the rotational drive that advances ice from the storage bin into the dispenser chute.This motor is a low-speed, gear-reduced drive that supplies short, controlled bursts of torque under command of the refrigerator control board; those bursts are timed to move a small amount of ice per dispense cycle and then stop to avoid bridging.In practical terms the motor couples to the auger shaft with a splined or pressed fit and uses a specific connector and mounting flange, so electrical interface, shaft diameterand mounting orientation determine compatibility with a given Frigidaire model.
- Primary function: rotate auger to transport ice from bin to chute.
- Common failure symptoms: no ice dispensed, motor hum with no shaft rotation, intermittent operationor stripped drive/gear noise.
- Compatibility checks: confirm connector pinout, mounting tab alignment, shaft diameter and rotation direction before replacement.
For troubleshooting and replacement, apply the manufacturer-specified supply from the dispenser control board and observe whether the motor responds with a smooth, low-speed rotation; a persistent hum without rotation typically indicates internal gear or shaft seizure while intermittent pulses can indicate an electrical or board-level fault. When replacing the unit, match mechanical and electrical interfaces rather than relying solely on visual similarity-correct shaft length, spline countand connector type are required for reliable operation. Basic bench tests include measuring continuity of the winding, confirming the connector delivers the expected control voltage during a dispense requestand checking for mechanical binding in the auger assembly before final installation.
| Item | Description |
|---|---|
| Function | Provides gear-reduced rotational torque to advance ice from bin to dispenser. |
| Failure indicators | No rotation,humming sound,or grinding indicative of internal gear or shaft damage. |
How the 241816602 Frigidaire Refrigerator Motor-AUGER Works inside the Appliance
The 241816602 Frigidaire Refrigerator Motor-AUGER is the low-speed, high-torque drive unit that rotates the auger inside the ice-bin/dispenser assembly to deliver measured ice to the dispenser chute. Mechanically, the motor contains a small gear reduction set that converts motor speed into torque sufficient to overcome packed or bridged ice; electrically it is controlled by the refrigerator’s dispenser switch and main control board through the cabinet wiring harness. When evaluating compatibility, technicians should verify the mounting footprint, shaft diameter and spline profile, and the electrical connector pinout to ensure proper engagement with the existing auger and harness rather than relying solely on model family names or visual similarity.
In operation the motor is intended for intermittent duty and will stall if the auger is blocked or if the internal plastic gears are worn; common failure modes include stripped gear teeth, bearing seizure, burnt windings from repeated stallsand connector/circuit faults upstream. Troubleshooting typically involves checking for voltage at the motor connector during a dispense request, inspecting the auger and housing for ice bridges or foreign objectsand verifying mechanical freedom by turning the shaft manually with the motor disconnected. Practical replacement decisions hinge on matching mechanical interfaces and confirming that the control board supplies the correct drive signal-if the motor receives proper voltage but does not turn,replacement is appropriate; if it does not receive voltage,the fault likely resides in the control or wiring.
- Key replacement checks: mounting pattern, shaft/spline fit, connector pinoutand evidence of gear or bearing wear.
| Item | description |
|---|---|
| Function | Rotates the ice auger to feed ice from the bin to the dispenser chute. |
| Mechanical interface | Spline-mounted shaft and specific mounting holes-must match bin housing. |
| Electrical interface | Low-voltage control signal from dispenser switch/control board via multi-pin connector. |
Common Failure symptoms and Diagnostic Indicators of Auger Motor Malfunction
The 241816602 Frigidaire Refrigerator Motor-AUGER is the direct-drive actuator that turns the ice auger to deliver ice from the bin to the dispenser. Functionally this motor converts the dispenser control board’s command into rotational torque transmitted through a gearbox and auger shaft; therefore failures can present as electrical faults, mechanical bindingor gearbox wear. Compatibility is model-dependent, so confirm the refrigerator model and part number before assuming the motor is at fault. Technicians should also inspect the auger, bite plateand ice chamber for packing or obstructions that can produce the same symptoms as a motor defect.
- No dispense and no audible activity – possible open circuit, failed drive signal, or blown fuse/relay.
- Motor hums but will not rotate - typical of a stall condition caused by frozen ice, stripped gearsor seized bearings.
- Intermittent rotation or stopping under load – indicates worn brushes (in brushed motors), intermittent connector/wiring faultsor degraded bearings.
- Unusual grinding or metallic noise - suggests gearbox tooth damage or bearing failure inside the motor assembly.
Effective diagnostics combine electrical measurement and mechanical inspection: confirm the dispenser control issues a voltage at the motor connector during a dispense command, check winding continuity and insulation to chassis with a multimeterand measure running current with a clamp meter to detect excessive draw consistent with stalls or bearing drag. A practical workflow is: clear visible ice, manually rotate the auger to check for binding, observe motor behavior unloaded versus under normal loadand isolate the harness to check for corrosion or intermittent contacts. These steps separate control-board or wiring faults from true motor/gearbox failures and help determine whether replacement of the motor assembly or repair of mechanical obstructions is required.
| item | Description |
|---|---|
| Voltage at motor during dispense | Presence of command voltage indicates motor is being driven; absence points to control-board, relayor wiring fault. |
| Running current | Elevated current during operation indicates stall, jamor bearing/gearbox failure; near-zero current suggests open winding or poor connection. |
Replacement Considerations, compatibility, and Installation Procedures for Auger Motor Assemblies
The 241816602 Frigidaire refrigerator Motor-AUGER is the drive assembly that turns the auger screw inside the ice bin, translating rotational torque into consistent ice feed for the dispenser. In typical installations the motor includes a reduction gear train and a keyed or splined output that mates to the auger shaft, plus an OEM wiring harness and mounting flange that register with the ice-chute housing. Technicians should evaluate both electrical and mechanical interfaces: identical part numbers ensure proper connector pinout, shaft profileand mounting hole alignment, while cross-referencing the refrigerator wiring diagram confirms control-signal requirements and any interlocks or microswitch feedback used by the dispenser control board.
Replacement requires careful handling of the mechanical fit and verification of electrical continuity. Before beginning, disconnect power and remove any cams, retainers, or gaskets that locate the motor to the chute so the auger can be withdrawn without bending the shaft; when reinstalling, ensure the splines fully engage and the gasket compresses evenly to prevent air leaks or binding. If the motor hums without turning, inspect the auger for ice jams and check motor winding continuity with a multimeter; verify correct voltage at the connector before replacing the assembly. After reassembly, run a short functional test through the dispenser controls to confirm torque under load and listen for abnormal noise that indicates misalignment or damaged gears.
- Compatibility checks: confirm part number, connector pinoutand shaft profile against the appliance schematic before ordering.
- Pre-install checks: inspect auger and housing for obstructions, replace deteriorated gasketsand note orientation of retaining clips.
- Installation steps: power off,remove retaining screws,seat motor splines,secure flange,reconnect harness,and test under controlled power.
| Item | Description |
|---|---|
| Part | 241816602 Frigidaire Refrigerator Motor-AUGER – OEM auger drive assembly for selected Frigidaire ice dispensers |
| Function | Provides reduced-speed torque to drive auger screw and meter ice to the dispenser mechanism |
| Interface | OEM mounting flange and splined/keyed output; verify connector pinout and harness compatibility with the refrigerator model |
| Troubleshooting | If motor hums but does not rotate: check for jammed auger, damaged splinesand motor winding continuity; verify control voltage at connector |
Q&A
What is the 241816602 Frigidaire Refrigerator Motor-AUGER and where is it located?
The 241816602 is an OEM auger motor assembly used in Frigidaire refrigerators that have an automatic ice maker and a door-mounted ice dispenser. It is indeed mounted behind the ice bin/ice chute inside the freezer door and drives the auger (spiral) that moves ice from the bin into the dispenser chute.
what are the common symptoms that indicate the auger motor has failed?
Common symptoms include: the dispenser switch activates but ice does not dispense, the motor hums or clicks without turning, grinding or metallic noises when dispensing, intermittent operation, or visible stripped/broken plastic gears. Before replacing the motor,check for ice jams and stuck/frozen ice in the auger housing.
How can I test the auger motor to confirm it needs replacement?
Start with simple checks: unplug the refrigerator and remove the ice bin to look for jams.If no jam is present, access the motor wiring harness and visually inspect for damage. With the unit powered and dispenser cycle called, check for voltage at the motor harness according to the service manual (use a meter and follow safety precautions).Also measure motor winding continuity with an ohmmeter-an open circuit indicates a failed winding. If the motor receives proper control voltage but does not turn, the motor or its gearbox is highly likely bad and should be replaced.
Can I repair the auger motor gearboxor do I need to replace the whole 241816602 assembly?
Most auger motors on modern Frigidaire refrigerators are sold as complete sealed assemblies (motor plus gearbox) and are not designed for field gearbox rebuild. If the internal gears are stripped or the motor windings are open,replacing the entire 241816602 assembly is the recommended and safest option.
How do I replace the 241816602 auger motor (basic steps and safety)?
Basic replacement steps: 1) Unplug the refrigerator and shut off the water supply (if applicable). 2) Remove the ice bin/cover and any trim to access the motor. 3) Disconnect the electrical connector and remove the mounting screws/clips that secure the motor. 4) Remove the old motor and install the new assembly,making sure the auger shaft and seals align correctly. 5) Reattach wiring and covers, restore powerand test the dispenser. Always follow the refrigerator’s service manual for model-specific instructions and wear gloves/eye protection.
Do I need any special tools or lubricants to install the new motor?
No special tools are usually required beyond common hand tools (screwdrivers and possibly nut drivers). If the service manual recommends lubricating the auger shaft or seals, use a food-safe (NSF-rated) lubricant sparingly. Do not use petroleum-based greases that are not rated for food-contact applications or that can degrade plastic components.
How do I know if the 241816602 is the correct replacement part for my refrigerator?
Confirm compatibility by checking the refrigerator’s model number (usually on a tag inside the fridge or freezer) and cross-referencing it with the part number in the manufacturer’s parts list or a trusted parts supplier.While 241816602 is a common Frigidaire auger motor part number, always verify fit and connector type against your specific model before purchasing.
Are there troubleshooting steps to try before replacing the motor to avoid unnecessary cost?
Yes. First,clear any ice clogs by defrosting the bin and checking for broken ice pieces. Test the dispenser switch and wiring harness for continuity and proper voltage during a dispense cycle (consult a wiring diagram). Reset the control board by unplugging the fridge for 1-2 minutes. If the motor only hums, tapping lightly to free a stuck gear might temporarily help, but persistent mechanical noise or no rotation typically means replacement is necessary.
In Conclusion
The 241816602 frigidaire Refrigerator Motor-AUGER is a purpose-built component that powers the auger mechanism in compatible refrigerator ice-dispensing systems. its primary role is to rotate the auger shaft that moves ice from the storage bin to the dispenser chuteand its reliable operation directly affects consistent ice delivery and user convenience. Although it does not impact cooling, a functional auger motor is essential for preventing jams, minimizing wear on related componentsand maintaining overall dispenser performance.
Because symptoms such as no ice, intermittent dispensingor unusual motor noise can stem from multiple causes-mechanical blockage, wiring faults, defective controls, or a failing motor-accurate diagnosis is important before replacing the part. When testing confirms the auger motor is at fault, installing the correct OEM 241816602 replacement and following proper installation and testing procedures helps restore reliable operation and avoids repeated failures. If there is uncertainty about diagnosis or safe installation, consulting trained service personnel ensures the repair is done correctly and preserves appliance safety and longevity.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
