241734001 Frigidaire Refrigerator Ice Bucket is a removable ice storage assembly used in frigidaire refrigerators equipped with automatic ice-making and dispensing systems. It is a molded plastic bin designed to collect and hold cubed ice produced by the ice maker; in dispenser-equipped models the assembly often includes interfaces for an auger drive, lidand alignment features that engage the dispenser mechanism. The part number identifies the specific geometry, mounting pointsand any integrated features (such as sensor mounts or drive couplings) that distinguish it from other ice storage components.
Inside the appliance the ice bucket functions as the intermediary between the ice maker module that harvests ice from the mold and the user-facing dispenser or internal shelf. It interacts mechanically with the auger and motor assembly when the dispenser is actuatedand it can interface with optical or mechanical full-bin sensors, door interlocksand the refrigerator control board.Proper fit and alignment are critically important to prevent jams, ensure reliable ice delivery, and allow sensors and switches to report accurate status to the control electronics.
In this article technicians, engineers, and appliance owners will find a technical overview of the ice bucket’s function, guidance on model compatibility and how to verify part-number versus refrigerator model, common failure symptoms to look for (such as dispensing jams, sensor faults, misalignmentor leaking), basic troubleshooting steps to isolate mechanical versus electrical issuesand practical considerations for replacement including correct installation, handling of associated components (auger, motor coupling, sensors)and testing after service. The intent is to provide concise,usable technical context to support diagnosis and repair decisions rather than consumer-facing marketing information.
Table of Contents
- Function and Role of the Ice Bucket in Refrigerator Ice Production,Storage,and Dispensing
- How the 241734001 Frigidaire Refrigerator Ice Bucket Integrates with the Ice Maker,Evaporator,and Sensor Systems
- Common Failure modes and Diagnostic Indicators for the Ice Bucket Assembly
- Compatibility Matrix,Replacement Considerations,and Step‑by‑Step Installation Procedure
- Q&A
- To Conclude
Function and Role of the Ice Bucket in Refrigerator Ice Production,Storage,and dispensing
The 241734001 Frigidaire Refrigerator Ice Bucket is the molded-storage and interface component that receives ice from the ice-maker module and presents it to the dispenser or user. Functionally, the bucket provides a controlled reservoir that prevents ice bridging against the ice-maker outlet, aligns with the dispenser auger or chute, and often contains mounting tabs, drive coupling featuresor sensor cutouts that allow the fridge’s control system to detect a full condition. Proper mechanical fit and orientation are required for the ice-maker to deposit cubes into the bucket reliably and for the dispenser mechanism to engage without binding.
During normal operation the ice-maker ejects cubes into the bucket where geometry and, in some models, a rotating auger or paddle reduce bridging and feed ice to the dispenser. Common functional failures related to the bucket include misalignment (causing jams or incomplete dispensing), cracking or deformation (leading to leaks or contamination)and worn coupling interfaces (preventing the auger from turning). Technicians replacing this component should verify model compatibility,inspect mounting tabs and the drive interface for wear,and test the bucket in situ to confirm that the ice-maker shutoff sensor and dispenser engagement operate as intended.
- Primary roles: ice collection, anti-bridging geometry, dispenser interface
- Symptoms of failure: dispensing jams, continuous ice production, visible cracks or warped mounting points
- Maintenance/repair notes: confirm OEM part number, inspect drive-coupling and sensor cutouts, clean interior to prevent clumping
| Item | Description |
|---|---|
| Material | Rigid food-safe molded plastic with smooth interior to reduce ice adhesion |
| Compatibility | designed for specified Frigidaire refrigerator models; confirm fit by part number before replacement |
How the 241734001 Frigidaire Refrigerator Ice Bucket Integrates with the Ice maker, Evaporatorand sensor Systems
The 241734001 Frigidaire Refrigerator Ice Bucket functions as both an ice storage container and a mechanical interface between the ice-making assembly and the dispenser. It is molded with specific mounting tabs, an auger coupling recessand a sensor aperture so the control board and dispensing motor can read ice level and transfer torque reliably; these features are matched to the manufacturer’s ice maker module rather than being universal. In operation the bucket receives ice from the freezer’s harvest cycle, positions that ice for the auger or dispensing arm, and presents a consistent optical or mechanical surface for the ice-level sensor to detect, allowing the ice maker to stop production when the bin is full and to engage the auger only when the bucket is correctly seated.
- Alignment tabs and mounting points: ensure repeatable seating and proper sensor alignment.
- Sensor aperture/notch: accommodates optical windows or mechanical bail arms used by the control system.
- Auger coupling recess: transmits drive torque without excessive play to prevent jamming.
- Ice chute/drain features: guide fractured ice away from the evaporator area and control melt runoff.
| Item | Description |
|---|---|
| Sensor interface | Clear window or notch that allows optical sensors or bail arms to detect ice level. |
| Auger coupling | Recessed cavity sized to accept the drive spindle and transfer torque to the auger. |
The bucket does not contact the evaporator directly, but its placement and condition influence ice bridging and frost migration from the evaporator to the storage area; excessive frost buildup on the evaporator or a cracked bucket wall can alter how ice piles and how sensors detect level, producing symptoms such as continuous harvest cycles or auger stalls.Practical service checks include verifying that the bucket seats flush against its stops, cleaning the sensor window of frost and scale, measuring sensor switch or optical sensor continuity with a multimeter, and inspecting the auger coupling for wear-replacing the 241734001 Frigidaire Refrigerator Ice Bucket when mounting features or the sensor aperture are damaged will often restore proper interaction between the ice maker, evaporator-related frost behaviorand sensing systems.
Common Failure Modes and Diagnostic Indicators for the Ice Bucket Assembly
The ice storage component designated 241734001 Frigidaire Refrigerator Ice Bucket performs two primary functions: it contains frozen water produced by the icemaker and provides a mechanical interface to the dispenser or auger assembly. Proper function depends on dimensional tolerance at the rim and mounting tabs, material integrity of the plastic shell, and unobstructed ice flow paths; small deformations or broken tabs will cause misalignment with the auger, increased motor torqueor intermittent dispensing. Compatibility is persistent by the bucket’s mounting geometry and sensor fittings on specific Frigidaire models, so physical fit and correct engagement with the auger/sensor assembly are diagnostic priorities when unexpected behavior appears.
- Visible cracks or hairline fractures in the bucket wall or mounting tabs causing water leakage or loss of secure seating.
- Ice bridging or clumping inside the bucket leading to intermittent dispensing or complete jams.
- dispenser motor stalls or draws higher current when engaging the bucket-indicator of increased mechanical load or auger slip.
- Bucket does not fully engage with auger spline or sensor-resulting in “no ice” errors despite ice present.
- Odor,discoloration,or visible biofilm indicating sanitation issues that can alter ice release characteristics.
| Item | Description |
|---|---|
| Broken mounting tab | Prevents secure seating; causes misalignment and auger coupling disengagement under load. |
| Ice bridging | Large ice lumps form within the bucket cavity, reducing flow and increasing dispenser motor torque. |
Diagnose failures by combining visual inspection with functional tests: remove the bucket and check mounting features and rim flatness, then operate the dispenser while measuring motor current or listening for abnormal rattle or stutter. For example, a motor that hums without turning usually indicates auger slippage from a fractured spline or incorrect bucket seating; conversely, intermittent dispensing with normal seating often points to internal ice bridging or contamination. When evaluating compatibility or replacement,compare the bucket’s mounting tab spacing and sensor cutouts to the refrigerator’s chassis-repair is limited to cleaning and minor edge reshaping,so replace the bucket if structural tabs are damaged or the part fails to meet original dimensional engagement.
Compatibility Matrix, Replacement Considerationsand Step‑by‑Step Installation Procedure
The 241734001 Frigidaire Refrigerator Ice Bucket is a molded ice collection and delivery assembly that interfaces directly with the ice maker/auger system and the refrigerator door dispenser. Its primary function is to receive ice from the ice maker, allow the auger to engage and transport portions of ice to the dispenserand protect the auger drive from obstructions. Technically, fit depends on the bucket’s mounting tab spacing, cutouts for the auger shaft and sensor openingsand overall envelope dimensions; buckets with mismatched tab geometry or shaft clearances will cause misalignment, auger binding, or sensor false-trips. Typical failure modes that affect compatibility include cracked or deformed mounting tabs, worn auger bearings, and broken sensor brackets-each condition can be verified visually and by checking that the auger rotates freely with the bucket in place.
When considering replacement and installation,verify the part cross-reference and the physical measurements against the refrigerator’s service manual rather than relying only on model names. For installation: remove power, drain and empty the bucket, release the retaining tabs or screws, inspect the auger coupling and sensor contactsand seat the replacement so that the bucket tabs fully engage the chassis catches; after restoring power, execute a manual auger rotation and a test dispense cycle to confirm clearance and sensor behavior. Use basic hand tools (screwdriver, pliers) and, if present, gently clean or replace any foam seals that interface with the door to prevent air infiltration and icing at the bucket interface.
- Power off and remove ice from bucket
- Release retaining tabs/screws and unclip bucket from chassis
- Inspect auger shaft, sensor bracket, and mounting tabs for wear
- seat new bucket, ensuring tabs and auger cutout align; reattach fasteners
- Restore power, run a manual auger test and one dispense cycle
| Item | description |
|---|---|
| Part number | 241734001 - molded replacement ice bucket for select Frigidaire models |
| Compatibility | Verify against service manual/model cross-reference and check tab spacing and auger cutout dimensions |
| Key Checks | mounting tab integrity, auger shaft clearance, sensor/bracket alignment |
Q&A
What is the Frigidaire part 241734001?
Part 241734001 is an OEM ice bucket (ice bin) assembly used in certain Frigidaire/Frigidaire Gallery and Electrolux refrigerators with automatic ice makers. It is the removable container that stores and delivers ice from the freezer ice maker to the dispenser or access area.
How do I know if 241734001 is the correct replacement for my refrigerator?
Verify compatibility by checking your refrigerator model number (usually on a plate inside the fridge or freezer) and cross-referencing it with the Frigidaire parts list or the parts seller’s compatibility tool.You can also match the old part number printed on the existing ice bucket or consult the refrigerator’s parts diagram. If in doubt, provide the appliance model number to an authorized parts dealer or Frigidaire customer support.
How do I remove and install the 241734001 ice bucket?
General steps: 1) Turn off the ice maker (use the on/off switch or raise the shutoff arm) and remove ice from the bucket. 2) If present, press any release tabs or lift the bucket slightly to disengage it from the mounting rails; then pull it straight out. 3) To install, align the bucket with the guides/rails and slide it in untill it seats and any retention tabs click. 4) Lower or turn the ice maker back on. Note: exact release mechanisms vary by model; consult your service manual for model-specific instructions and disconnect power if you will be working on or around electrical components.
What tools are needed to replace the ice bucket?
Most replacements require no special tools - the bucket typically slides in and out by hand. If plastics or trim pieces must be removed first, a Phillips screwdriver and a flat plastic trim tool may be helpful. Always use non-marring tools on plastic trim and consult the service manual if screws fasten the assembly.
how should I clean the 241734001 ice bucket?
Empty the bucket and wash it by hand with warm water and mild dish soap. Rinse thoroughly and dry completely before reinstalling. Do not use abrasive pads or harsh chemicals (bleach unless properly diluted and rinsed); most OEM plastic ice buckets are not dishwasher-safe and could warp or crack if exposed to high dishwasher heat.
My ice bucket is cracked or broken - can I repair it or should I replace it?
Small cosmetic cracks can sometimes be temporarily sealed with food-safe silicone, but because cracked buckets can harbor bacteria and may leak or fail structurally, replacement with the OEM part is the recommended permanent solution. Use the correct Frigidaire part number (241734001) or a verified compatible OEM replacement.
Ice is not dispensing even though the ice maker is making ice - could the bucket be the problem?
Yes,possible causes related to the bucket include: jammed or compacted ice inside the bucket,the bucket not seating correctly so the auger or dispenser motor isn’t engaging,a broken drive coupling/actuator in the bucket,or a misaligned bucket sensor/actuator. Also check for frozen ice bridges, freezer temperature (should be about 0°F / -18°C)and the dispenser motor/auger assembly. diagnose by removing the bucket, inspecting for broken components and ice jamsand confirming the motor engages when the bucket is properly seated.
how can I be sure I’m buying a genuine OEM 241734001 and not a poor aftermarket copy?
Buy from authorized Frigidaire/electrolux parts dealers or the manufacturer’s official parts store when possible. Genuine OEM parts typically carry the Frigidaire logo, part number molded into the plasticand come in branded packaging. Compare the physical part (dimensions,mounting points,connector locations) to the original and check seller return policies and reviews. if the listing does not explicitly state OEM/Frigidaire, ask the seller for verification.
To Conclude
The 241734001 Frigidaire refrigerator ice bucket plays a straightforward but important role in everyday appliance performance. As the receptacle for ice production and storage within compatible Frigidaire models, it helps ensure hygienic containment, smooth dispensingand proper interaction with the surrounding components of the ice-making system. A correctly functioning ice bucket supports consistent ice quality, prevents blockages or misfeedsand contributes to the overall reliability of the refrigerator’s ice-making and dispensing features.
Accurate diagnosis and timely replacement are critically important when the ice bucket shows signs of wear, damageor improper fit. Common indicators-such as cracked or warped plastic, persistent ice jams, misaligned sensors or mounting pointsor contamination that cannot be cleaned-warrant a careful inspection. Using the correct replacement part (for example, part number 241734001 for compatible Frigidaire units) and following manufacturer installation guidance or professional repair procedures helps restore normal operation, avoids strain on adjacent componentsand reduces the likelihood of repeat issues.
Maintaining or replacing the ice bucket when necesary is a cost-effective step toward preserving appliance performance,food safety,and user convenience. Routine checks and an evidence-based approach to repair ensure the refrigerator’s ice system continues to function as intended, prolonging the service life of the appliance and supporting consistent performance for household use.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
