WH13X10029 GE Washer 2 In 3 Out Water Valve is⤠an electro-mechanical inlet âvalve assembly used in laundry appliances too control â˘and⢠route⣠incoming water. It is âa multi-port âsolenoid valve that accepts two â¤supply lines (typically hot⢠and cold) andâ provides three controlled â˘outlets to⢠the âwasher’s internal plumbing; the valve contains solenoid coils, valve seats/diaphragms, âand standardized electrical connectors and mounting points that allow it to be âdriven by the machine’s⤠control board.
Inside the appliance, this valve’s roleâ is to direct and metre water⢠flow âaccordingâ to the selected wash cycle, temperature â˘selectionand⤠dispenser routing. It âinterfaces directly with the household water supply, âŁthe washer’s internalâ hoses, the electronic âcontrol module (or timer)and associated sensors such as fill-level or pressure â¤switches; correct operation ensures proper water volume, temperature mixingand delivery â¤to⤠the wash tub or dispenser while preventing backflow and leaks⣠when de-energized.
In the following article âŁreaders will âfind a technical description of â˘the valve’s function and plumbing/electrical interfaces, guidance on model compatibility and identifying the correct replacement, common failure symptoms (no fill,⤠continuous fill, incorrect temperature,â leaksor intermittent operation), step-by-step troubleshooting checks (electrical continuity and⢠coil voltage, inlet pressure, â¤hose conditionand control signals)and practical replacement considerations such as port orientation, connector⢠type,⢠sealingand âpost-installation tests.The material is⣠intended to help⤠technicians, engineersand appliance owners diagnose problems and make informed choices about repair or replacement without⣠marketing language âor unverifiedâ claims.
Table of Contents
- Function and Role of the 2âIn/3âOut Water Valve in Washer Fill and Cycle Control
- How âthe⣠WH13X10029 âGE Washer 2 In 3 Out Water Valve Works Inside the Appliance: Internal Flow âPaths, Solenoidsand Electrical Interface
- common Failure Symptoms and Diagnostic âProcedures for Flow loss,â Stickingâ Portsand Electrical Faults
- Compatibility, Replacement Considerationsand Installation Procedures for WH13X10029â and Equivalent Valve Assemblies
- Q&A
- To Conclude
Function and âŁRole of the 2âIn/3âOut Water â˘Valve in Washer Fill âand Cycle â˘Control
The WH13X10029 GE Washer 2 In 3 Out Water Valve is âa âŁsolenoidâactuated valve assembly that âŁcontrols the delivery âof hot and cold âwater to multiple machine circuits. âŁIt âaccepts two inlet lines (hot and cold)â and⣠directs âwater throughâ three âdiscrete outlets underâ commandâ of the washer⢠control board; each outlet â˘correspondsâ to a different fill path such as the â˘main wash tub, a rinse lineor a dispenser circuit. Theâ valve contains âindividual poppet/seat assemblies and solenoids that open⢠or close⢠specific outlet passages when⢠energized, so â¤correct electrical connector orientation,â port alignmentand âmounting location must match⢠the washer model for proper â˘compatibility⤠and⣠sealing.
During a cycle theâ control board energizes the appropriate solenoids to achieve timed orâ mixed temperature fills (for example, a blended warm fill by sequencing hot and cold outputsorâ a coldâonly rinseâ by energizing the cold âoutlet). âCommon service⢠observations âinclude a noâfill condition (noâ click or no water), continuous fill (stuck open poppet)or âinternal leakage between ports. Technicians commonly verify valve function âbyâ listening for solenoid clicks, checking coil continuity, confirming control board output voltage during a commanded âŁfilland inspecting inlet screens and âoutlet hoses; because the manifold and âsolenoids are integrated, replacement of the WH13X10029 â˘assembly is typically the practical repair rather than individual âcomponent rebuilding.
- Features: two inlet ports, â¤three outlet ports, solenoidâactuated poppets⢠for selective routing.
- Common failure symptoms: no fill, slow fill, continuous fill, crossâport leakage, clicking without water flow.
- Field diagnostics: listen forâ solenoid â˘actuation, measure coil âcontinuity, verify controller output,â inspectâ screens âand âŁhose connections.
| Item | Description |
|---|---|
| Inlet ports | Two (hot âand cold)⣠– feed into internal manifold |
| Outlet ports | Three â¤discrete outlets for wash, rinse and âŁdispenser/auxiliary lines |
| Actuation | Solenoidâdriven poppet valves controlled by âwasher âelectronic controller |
| Typical issues | Stuck poppet, coil failure, internal leakage, clogged âinletâ screens |
How the WH13X10029 GE âWasher â2 In 3 Out Water Valve Works Inside the Appliance: Internal Flow â¤Paths, â¤solenoidsand âElectrical Interface
The WH13X10029 GE Washerâ 2 âŁin 3 Out Water Valve is a multi-port control assembly that directs⣠hot and⣠cold inlet water through built-in passages to threeâ separate outlet ports used by wash, rinse,â andâ auxiliary fill functions.Inside the molded valve body, âŁeach outlet is sealed by a plunger or diaphragm that â¤is held closed until its corresponding coil is energized; energizing a coil lifts âthe seal⣠and allows theâ selected inlet manifold to pressurize the chosen outlet channel. The valve’s internal flow paths are arranged so a single inletâ can feed⣠multiple outlets without cross-contamination when seals are functioning correctlyand the â¤physicalâ orientation of inlets and outlets âŁmust match the â¤washer’s plumbing during replacement. Electrical â˘actuation is provided by âŁindividual coils on â˘each port, â¤with âthe washer’s control board completing the âŁcircuit for only the required outlet atâ any time.
- Solenoids: âŁeach outlet has an âindependent âcoil thatâ the controllerâ switches on for the desired â˘fill.
- Internal seals: âŁdiaphragms or poppetsâ isolate ports to prevent âŁcrossflow when de-energized.
- Electrical interface: multiple âquick-disconnect terminals on a single connector, one wire perâ coil âplus a common return in some harnesses.
- diagnostics: â˘a â˘failed coil shows open circuit or stuck plunger; hydraulic symptoms include no â˘fill,continuous fill,or incorrect temperature.
| Item | Description |
|---|---|
| Inlets | Two⤠supply âŁportsâ (hot and cold) routed âinto the manifold. |
| Outlets | Three controlled ports for wash/rinse/auxiliary fills. |
| Coils | Three independent actuators âŁcontrolled by⢠the washer’s control board. |
| Connector | Multi-pin quick-disconnect harness; wire colors varyâ by model. |
For practical â˘servicing, technicians checkâ coil continuity with a multimeter and observe valve⤠behavior during a manual fill âcycle toâ isolateâ electrical from⣠hydraulic failures; a coil that âmeasures open âor a plunger that does not move when energized indicates replacement.When installing aâ replacement WH13X10029â GE Washer⣠2 In 3 Out â¤Water âValve, match the inlet/outlet orientation, verify the wiring âharness pinout, replace O-rings â¤or gasketsand â˘perform wet⢠tests at low âpressure to confirm thereâ is no âŁcrossflow or âleakage before â˘returning the washer to normal service.
Common Failure Symptomsâ and diagnostic Procedures for âFlow â¤Loss, sticking⤠Portsand Electrical Faults
The âŁWH13X10029 â¤GE Washer 2 In 3 Out Water valve is âa multiâport solenoid assembly that directs two inletâ feeds to three separate fill paths; symptoms of failure typically include âcomplete or partial flow loss, crossâfeeding between hotâ and cold, âŁcontinuous⤠fillingor intermittent â¤operation when the control calls for a specific port. Mechanical failure usually shows as slowâ fill or no âfill despite correct inletâ pressure, while sticking ports⢠ofen cause â¤the wrong⢠temperatureâ mix or simultaneous⤠filling of multiple compartments.â Electrical faults present âas open or shorted solenoid â˘coils, noâ drive signal from the control board, â¤or intermittent continuity âŁthat âcorresponds with erratic valve behavior; in practice, a machine that only fillsâ cold often points⣠to the hot solenoid or hot⤠inlet path âbeing â¤obstructed or mechanically âstuck rather than a software issue in âthe controller.
Diagnostic procedures follow a systematic separation ofâ plumbing, mechanicaland electrical causes. â¤Start with âa visual inspection of inlet screens âand hoses, then verify inlet water⣠pressure and observe valve behavior during a fill cycle: if the control board outputs âthe correct driveâ signalâ but no flow occurs, the problem is mechanical (clogged ports, diaphragm wear, âor a seized spool); if no drive voltage appears at the valveâ connector, trace wiring and test âthe control.â Practical tests include listening⣠for solenoid clicks â˘during actuation, using a multimeter toâ measure â˘coil resistance and connector voltage while âcycling the machine, benchâtesting solenoids with a currentâlimited supply per service specificationsand disassembling the valve to inspect diaphragms andâ Oârings for mineral⤠deposits. Replace the valve âŁwhen âcoilsâ are open/shorted, diaphragms are tornor ports are excessively corroded; document voltage and resistance readings to differentiate control faults from valve failures.
- No fill or slow fill: check inletâ screens, âwater pressureand valve port blockage.
- Wrong temperature or crossâfeed: inspect diaphragms/ports for sticking and⢠verify individual⣠solenoidâ actuation.
- Continuous⢠fill: confirm control signal termination and inspect valve seating/damaged diaphragm.
- Intermittent operation: measure coil⢠continuity âŁand testâ for intermittent âŁconnector voltage under load.
| Item | Description |
|---|---|
| Symptom | likely cause⣠/ Recommended test (visual, pressure, continuity, applied drive) |
| No⤠flow with control drive⤠present | Blocked inlet/port or failed diaphragm – inspect â˘screens,â remove valve and check internal passages |
| No âŁdrive âto valve | Wiring or control âboard fault – measure connector voltage during fill cycle and traceâ harness |
| Solenoid open⢠or shorted | Electrical failure – measure coil resistance; replace valve if out of spec âŁor shows intermittent continuity |
Compatibility, Replacement Considerations, â¤and Installation Procedures âfor âWH13X10029 and âŁEquivalent Valveâ Assemblies
The WH13X10029 GE Washer 2 âIn 3 Out Water Valve is a multi-solenoid⣠valve assembly that routes hot and âcold water to multiple machine paths (fill, â˘wash, rinse) under control of the washer’s â¤electronic board. Each solenoid opensâ a⢠passage from â¤one of the⣠two inlets to one of â¤three â¤outlet ports, â˘and the assembly typically contains integral screens and â¤check diaphragms⣠to âprevent backflowâ and debris ingress. Functionally, techniciansâ should verify coil voltage and connector pinout against the machine harness before replacement: âmost domestic GEâ washers use 120 VAC coils and â˘a keyed âmulti-pin connector, but some model variants and aftermarket equivalents differ in mounting flange geometry, port orientationand flow characteristics, which can⣠effect fit and timing of fillsâ in the control program.
Replacement and âinstallation require both mechanical and electrical verification to â˘restore reliable operation. Before reinstalling âthe valve, inspect and clean inlet screens, confirm gasket condition âor âreplace sealing gasketsand check coil resistance⣠and insulation to detect degraded solenoids; if one coil is faulty while the⢠valve body isâ intact,â coil â¤replacement can⤠be a â˘lower-cost repair provided the replacement coil matches âthe original specifications. After mounting âand reconnecting the harness, perform a controlled test cycle to exercise each â¤outlet and observe fill rates andâ leaks; document any differences in flow or timing versus the original valveâ as âthese can âŁindicate an incompatible aftermarketâ assembly or partial obstruction.
- Isolation: âshut off water âŁand power, then⤠relieve âpressure by⢠running a drain orâ opening âŁa faucet.
- Disassembly: remove access panel, label harness wires, detach inlet/outlet hosesandâ retain mounting hardware and gaskets.
- Inspection:⢠clean inlet âŁscreens, measure coil⢠resistanceand âcompare port⣠sizes andâ mounting hole locations to the âreplacement part.
- Installation: seat new gaskets, align valve ports correctly to the manifold, torque mounting screws evenlyand reconnect the harness with secure âclips.
- Verification: runâ diagnostic fill cycles,measure seconds-per-gallon fill rates,and perform a leak check under normal and pressurizedâ conditions.
| Item | Description |
|---|---|
| Ports | 2 inlets (hot/cold) and 3 outlets (wash/rinse/aux) with⤠internal check diaphragms |
| Coil âŁVoltage | Typical household specification: 120⤠VACâ per solenoid (verify match to washer model) |
| Connector | Multi-pin keyed harness; confirm pin mapping âbefore swapping |
| Common Failures | Leaking valves, stuck diaphragms, open⤠coils, clogged inlet⣠screens |
| Service Tip | Measure coil continuity and âperform âcontrolled fill⣠tests to â¤validate replacement compatibility |
Q&A
What is the WH13X10029 â¤water valve and what does “2 â˘in 3 out” mean?
The WH13X10029 â˘isâ a GE OEM inlet water valve assembly âused â¤on âmany GE â˘topâload washers. “2⢠in 3 out” means the valve has two⣠waterâ inletsâ (hot and cold)⤠and three outlet ports -⣠typically a hot outlet, a cold outlet and a mixed/warmâ outlet (the valve opens combinations ofâ the hot and cold âports âto deliver hot,⢠cold or warm fills to â¤theâ tub).
What âare the commonâ symptomsâ of⢠a failingâ WH13X10029 âvalve?
Common signs include no fill or partial⣠fill, only hot or⤠only cold water coming into the washer, slow or intermittent fill, a⤠continuous flow or dripping when the washer is off, â¤and audible humming or buzzingâ from the valve. Leaksâ at the valve or âhoses are anotherâ sign a diaphragm or seal has failed.
How can I âŁtest the valve electrically and mechanically?
For electrical testing: â˘unplug the washer, remove the valve âwiring harness and use a multimeter to checkâ each solenoid coil for continuity. Most GE solenoids âwill show continuity⤠(resistance varies by model – typically⤠a few hundred to a thousand ohms). With the washer powered andâ a service tech operating controls, measure the voltage at the valve connector whenâ a fill is requested; it should âŁshow the control voltage specified in the service manual âŁ(commonly ~120 VAC on⣠many GE machines). For mechanical testing: turn âoff water, disconnect the outlet hoses and briefly energize the appropriate solenoid to âŁverify which outlet opens (do this only if you areâ qualified and have removed excess water). Alwaysâ follow safety â¤procedures: disconnect power before removing the valve or probing wiring.
How⢠do I replaceâ the WH13X10029 valveand what precautions should I âtake?
Replacement steps: unplug the washer and âshut off hot and cold waterâ supply valves;⣠relieve pressure by running âa drain or opening a cabinet⤠drain hose; disconnect inlet hoses and remove mounting screws or clips holding theâ valve; â˘unplug the wiring harness and label wires if needed; remove the valve and install the new one,â making sure seals/gaskets are âcorrectly seated;⢠reconnect hoses and â˘wiring, â¤turn water on and âŁcheck for leaks. âPrecautions: always cut power before working on electrical parts, useâ new Oârings/gaskets, handâtighten hose fittings and then give a small additional turn (do not âovertighten),⣠and checkâ forâ leaks before returning the washer to normal service.
How do I know if WH13X10029 is the correct replacement âfor my GE washer?
Confirm compatibility by matching the part number â¤on the old valve or the part number listed⤠in your washer’s parts list/service⣠manual. Also âŁverify âphysical aspects: inlet/outlet spacing, mounting â¤tab locations, electrical âŁconnector⣠type,⣠and number/color coding⣠of ports. If in doubt, provide your âwasher’s model number to âa parts supplier âor consult GE service âdocumentation âŁto verify âthe âcorrect OEM part.
Why is my washer only filling with cold (orâ only hot) water even though the valve looks OK?
if the washer fills onlyâ with cold or hot, possible⢠causes include âa â¤failedâ hotâ (or cold) solenoid on the valve, a blocked inlet hose â¤or screen/strainer, kinked supply hose, a âwiring orâ control⣠board fault that⢠isn’t energizing âthe correct solenoidorâ a âclogged water line/adapter. Inspect inlet strainers/screensâ inside the valve⤠for debris, check continuity/operation of âŁthe solenoid, verify⢠the control is â¤sending voltage to the correct valve terminal during fill,⣠and ensure supply hosesâ and shutoff valves â¤are⢠fully open.
Can I⤠use an aftermarket valve instead of the OEM⢠WH13X10029?
Aftermarket valves are available and may be less expensive,but OEM parts are recommended⣠to ensure correct fit,flow characteristics and longâterm reliability. If you choose an aftermarket valve, verify⣠that itâ matches the OEM in inlet/outlet spacing, portâ configuration (2 inâ /â 3â out), mounting styleand electrical connectorâ type. Also ensureâ it includes necessary gaskets/seals and is rated for your washer’s supply voltage.
To âŁConclude
The WH13X10029 âŁGE⤠Washer 2 â˘In 3 Outâ Water Valve â˘plays a centralâ role in controlling water delivery and distribution within âŁthe washing â˘machine. By regulating hot and cold inlet flow to multiple outlets that feed âthe tub and dispenser, â˘this valve⤠directly affects fill behavior, water temperature, rinse performance â¤andâ overall cycle â˘reliability. Itsâ correct function is therefore integral to both⣠appliance performance and the prevention⢠of water-related damage.
Accurate diagnosis is essential â¤when valve-related symptoms appear-such as failureâ to fill,continuous filling,incorrect water temperature,or visible leaks-toâ avoid unnecessary ârepairs⢠andâ to address the root cause⤠promptly. testing solenoids,⢠checking electrical continuity andâ connectionsand inspecting hoses andâ sealsâ are âŁpractical diagnosticâ steps; when in doubt, a serviceâ manualâ or âqualified technician can⢠ensure the problem is âidentified correctly⣠and safely.
When replacement is required, installing the correct⣠WH13X10029 valve (or anâ approved equivalent)⤠and⣠following⣠properâ installation and âtesting procedures restores intended function and âreliability. Proper replacement, âŁattentive reassemblyand â¤post-installation âŁtesting minimize the risk ofâ recurrence and help⤠maintain appliance safety â¤and longevity. For complexâ cases or â˘where warranty and safety considerations apply, professional service provides the most reliable⤠outcome.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
