WX14X10005 GE Washing 4’ Polymer coated Water Inlet Fill Hose 2 Pack is a replacement inlet hose assembly intended for use with residential washing machines and similar laundry appliances. The component consists of 4-foot flexible hose sections with a polymer coating over the hose braid and factory-installed fittings sold as a two-piece set; as an appliance plumbing component it provides the pressurized water path from the household supply to the machine’s internal inlet ports.
Inside the appliance system the inlet fill hose interfaces directly with the household water supply and the washer’s water inlet valve(s), and it is part of the broader fill and level control subsystem. when the control board or mechanical timer calls for water, the inlet valve opens and water flows through the hose into the tub or dispenser; the hose thus sees cyclical pressure, occasional temperature variation, vibration, and exposure to detergents or external abrasion. Proper hose selection, routingand connection are critically important for maintaining consistent flow, preventing leaks, and avoiding undue stress on the valve and cabinet penetrations.
This article will explain the hose’s function and typical submission, outline compatibility considerations (length, fitting typeand coating/material), describe common failure symptoms to watch for (external abrasion, swelling, leaks at fittings, restricted flow)and cover practical troubleshooting and replacement considerations for technicians and appliance owners. Topics include inspection points, how the component interacts with inlet valves and supply pressure, criteria for selecting a replacement hoseand safety practices to follow during diagnosis and replacement to minimize the risk of water damage.
Table of Contents
- Function and Role of the Water Inlet Fill Hose in GE Washing Machines
- How the WX14X10005 GE Washing 4′ Polymer Coated Water Inlet Fill Hose 2 Pack Operates Within the Washer’s Inlet Valve and Water Path
- Common Failure Symptoms, Wear Modesand Leak Detection Procedures for inlet Fill Hoses
- Replacement Considerations, Model Compatibilityand Installation Best Practices for Inlet Fill Hoses
- Q&A
- The Conclusion
Function and Role of the Water Inlet Fill Hose in GE Washing Machines
The WX14X10005 GE Washing 4′ Polymer Coated Water Inlet Fill hose 2 Pack serves as the flexible conduit that delivers household water from the shutoff supply to the washing machine’s inlet assembly. Each hose in this 2-pack is four feet long and uses a polymer coating intended to resist abrasion, chafing, and external corrosion that can accelerate failure in confined utility spaces. In normal operation these hoses transmit incoming supply pressure to the water inlet valve, so their internal diameter, material adaptability, and integrity directly affect fill rate and the responsiveness of the washer’s fill-control systems. The two-hose pack is convenient for replacing both hot and cold connections to ensure matched performance and reduce the risk of mismatched materials or age-related failure on one side of the machine.
- Common symptoms of hose-related issues: visible bulging, wet spots or dripping at connections, slow fill timesand intermittent loss of flow.
- Practical checks: inspect polymer coating for abrasions, verify swivel fittings turn smoothlyand replace the rubber washers when reinstalling to ensure a leak-free seal.
| Item | Description |
|---|---|
| Length | 4 feet |
| Material | Polymer-coated flexible tubing (designed for abrasion resistance) |
| Fittings | Standard residential inlet thread (typically 3/4″ GHT – verify model compatibility) |
| Pack | Two hoses (suitable for replacing both hot and cold lines) |
Functionally, a properly installed inlet fill hose maintains consistent flow characteristics under the range of household pressures and temperatures and prevents external damage that can lead to sudden leaks. A kink, internal collapseor degraded coating will reduce effective flow area and extend fill times, which can trigger diagnostic faults or uneven cycle operation; conversely, a leaking hose can cause water damage and erratic pressure signals to the washer’s controls.For technicians and appliance owners replacing these hoses, confirm thread type and orientation, hand-start threads then tighten with an appropriate wrench to avoid cross-threadingand test under full supply pressure while observing all connections for leaks before returning the appliance to service.
How the WX14X10005 GE Washing 4′ Polymer Coated Water Inlet Fill Hose 2 Pack Operates Within the Washer’s Inlet Valve and Water Path
WX14X10005 GE Washing 4’ Polymer Coated Water inlet fill Hose 2 pack functions as the flexible conduit between the home water supply and the washer’s inlet valve assembly. Each hose connects to the supply shutoff and the washer inlet using standard threaded fittings and a compression seal; the hose itself does not regulate flow but must withstand mains pressure and deliver an unrestricted flow to the inlet valve when the valve is energized. The polymer-coated exterior provides abrasion resistance and basic corrosion protection for the braided/reinforced inner tube, helping maintain integrity where the hose bends or contacts chassis edges. Technicians should verify the inlet thread type, inlet orientationand available routing space before installation to confirm compatibility with the washer model and to ensure the 4’ length provides adequate reach without kinking.
Within the washer’s water path the hose simply transmits supply water to the inlet valve solenoids; when a fill command is issued the valve opens and the hose delivers pressurized water into the valve body where screens and flow passages direct water to the tub or dispenser. Diagnostic distinctions useful in practice: a collapsed, kinkedor internally degraded hose will cause restricted flow or intermittent filling, while a properly functioning hose that allows full mains pressure and volume points the fault toward the inlet valve, valve solenoidsor internal inlet screens. during service, inspect hose ends and the polymer coating for cuts, deformitiesor bulges, hand-start fittings then secure with a wrench to avoid overtightening, and consider that the hose can damp mechanical vibration and help reduce water-hammer transmission compared with uncoated or brittle alternatives.
- Length and form factor: 4′ per hose, flexible routing for rear and side inlets.
- Connection: standard female hose threads common to residential washer inlets (verify before replacement).
- Construction: polymer-coated exterior over a reinforced supply tube for abrasion and corrosion resistance.
- Common service symptoms: leaks at fittings, reduced fill rate from kinks/clogs, visible exterior damage indicating replacement.
| Item | Description |
|---|---|
| Length | 4 feet per hose; sold as a 2-pack |
| Material | Polymer-coated exterior with reinforced inner supply tube |
| Connection | Standard residential inlet thread – confirm match with appliance inlet |
| Service role | Conveys mains water to inlet valve; does not modulate flow |
Common Failure Symptoms, Wear Modesand Leak Detection Procedures for Inlet Fill Hoses
The WX14X10005 GE Washing 4′ polymer Coated water Inlet Fill Hose 2 Pack is a replacement inlet hose assembly designed to deliver pressurized water from the household shutoff valve to the washer’s internal fill valve. The hose combines a braided reinforcement for burst resistance with a polymer outer coating that reduces abrasion and chafing where the line passes through cabinets or against metal fittings. This part is compatible with washers that use the standard female inlet thread and similar supply spacing; confirm thread size and inlet orientation before installation. In typical installations the hose carries cold or hot mains water at household pressures and undergoes repeated flexing during service, so routing, support, and proper connector engagement directly affect long-term performance.
failure modes include abrasion of the outer coating, braid fatigue at high-stress bend points, O-ring or ferrule degradation at the connectors, and thermal or chemical aging that produces embrittlement or pinhole leaks. Common symptoms are wetness at or near the hose crimp, visible fraying of the braid, bulging or soft spots in the hose body, reduced or intermittent fill flowand mineral build-up or corrosion at the threaded fittings. Diagnostic checks begin with a visual and tactile inspection, followed by a pressurized observation during a fill cycle; use a soap solution or paper towel to localize slow leaksand verify that inlet washers and connector seats are intact. If the hose shows cracking, persistent seepage, or deformation at the fittings, replacement is recommended rather than repair becuase internal damage can be concealed under the polymer coating.
- Visual check: inspect polymer coating, braid integrityand connector threads for corrosion or deformation.
- Operational test: run a fill cycle and watch for leaks under pressure; check both ends and along the length.
- Leak localization: apply a soapy water solution or paper towel along the hose to find slow or pinhole leaks.
- Fitting inspection: shut off water, relieve pressure, disconnect and inspect inlet washers, O-ringsand ferrules.
- Replace when any cracks, bulgesor persistent leaks are detected; match thread size and material compatibility.
| Item | Description |
|---|---|
| Typical wear location | Bend points and crimped connector areas where flex fatigue and abrasion concentrate. |
| Diagnostic indicator | Visible seepage, wet residue after a fill cycleor soap-bubble formation under pressure. |
Replacement Considerations, Model Compatibilityand Installation Best Practices for Inlet Fill Hoses
The WX14X10005 GE Washing 4′ Polymer Coated Water Inlet Fill Hose 2 Pack is an OEM-style inlet hose assembly designed to deliver household water to the washer inlet valve while resisting external abrasion and corrosion. the polymer-coated exterior provides a protective barrier over the flexible inner tube and fittings, reducing chafing where the hose passes behind the appliance; the hose length and fitting geometry must match the appliance inlet orientation to avoid strain. Confirm the appliance’s inlet thread and valve type before replacement-many washers use a standard appliance inlet thread, but some models require right-angle or specialized fittings-so compatibility checks prevent leaks and premature stress on the valve or hose ends during operation and service.
Replace the hose if you observe leaks, bulging, surface cracking, significant mineral buildup at the fittingsor a loss of structural flexibility; these symptoms indicate compromised internal layers or seals. For installation:
- Shut off the water supply and relieve pressure, then disconnect the old hose and inspect the inlet valve and threads for damage.
- Fit the new hose, ensuring the rubber gasket or washer seats correctly; hand-tighten the coupling and finish with no more than a 1/4 turn with a wrench to avoid deforming plastic fittings.
- Route the hose to avoid kinks, sharp edgesand heat sourcesand secure it so it cannot rub against cabinet edges during use.
- Pressurize the connection and inspect for leaks under load for several minutes; recheck after the first wash cycle.
| Item | Description |
|---|---|
| Length | 4 feet (per hose) |
| Material | Flexible inner hose with polymer coating for abrasion and corrosion resistance |
| Intended use | Washing machine water inlet; verify thread type and valve compatibility with appliance |
| OEM Part | WX14X10005 GE Washing 4′ Polymer Coated Water Inlet Fill Hose 2 Pack |
Q&A
what is the WX14X10005 hose and what is included in the 2-pack?
WX14X10005 is an OEM replacement water inlet (fill) hose sold for GE washing machines. The listing is a pack of two 4-foot polymer-coated inlet hoses – one intended for the hot water inlet and one for the cold – so you get both hoses needed to connect a washer to the household supply valves.
What size and type of fittings do these hoses have? Will they fit my washer and supply valves?
These hoses use the standard 3/4‑inch female inlet fittings used on most residential washing machine supply valves and appliance inlets. They will fit the vast majority of GE washers and othre brands that use the common 3/4‑inch supply valves. Always confirm your washer’s inlet thread and the supply valve size in your owner’s manual before buying if you have a non‑standard installation.
Is the polymer coating critically important? What are the benefits compared with plain rubber hoses?
The polymer coating covers the braided inner hose and provides extra protection against abrasion, chafingand cosmetic corrosion. Compared with plain rubber hoses, polymer‑coated braided hoses are typically more resistant to wear, less likely to kinkand offer improved durability and a longer service life.
Can these hoses be used for both hot and cold water?
Yes – the pack contains two identical 4‑foot hoses intended for use on the hot and cold inlets. They are built to handle normal household hot and cold water temperatures. Make sure you attach the hose from the hot supply valve to the washer’s hot inlet and the cold to the cold inlet.
How do I install the inlet hoses and what torque should I use?
Turn off both water supply valves and run the washer to relieve pressure. Remove the old hoses (have a towel or bucket for residual water). Verify rubber gaskets are in the hose fittings (replace if missing). Thread the new hose onto the washer inlet by hand, then hand‑tighten the supply valve end; finish with a quarter turn using pliers – do not overtighten. Turn the water back on, check carefully for leaks at both endsand tighten slightly if needed. Follow the washer manufacturer’s installation guidelines.
What pressure and temperature are these hoses rated forand are there any limits I should know?
Polymer‑coated braided inlet hoses are designed for typical residential water pressures and temperatures. While exact ratings can vary by manufacturer, these hoses generally handle standard household pressures (commonly up to around 100-150 psi at room temperature) and normal hot‑water temperatures used for laundry. For precise pressure/temperature limits, check the packaging or GE’s specification sheet. if your home has unusually high water pressure, install a pressure regulator or consult a plumber.
How often should I replace these hoses or inspect them for problems?
Inspect hoses every 6-12 months for signs of wear, kinks, bulges, cracking, corrosion at the fittingsor leaks.Many manufacturers and plumbing professionals recommend replacing washing machine inlet hoses every 3-5 years as a preventive measureor instantly if you observe any damage or leakage.
Do these hoses come with washers/gasketsand can they be used on other appliances?
Most OEM inlet hoses include the rubber sealing gaskets inside the female fittings; however, always verify the presence of gaskets before final installation and replace them if aged or missing. These hoses are intended for washing machines and other appliances that accept the same 3/4‑inch inlet fittings; they are not suitable for appliances that use different connector sizes or specialized fittings (such as, some dishwashers or water filtration equipment). When in doubt,check the appliance inlet specification.
The Conclusion
The WX14X10005 GE Washing 4′ Polymer Coated Water Inlet Fill Hose 2 Pack serves a essential role in delivering household water to the washing machine while protecting the connection against abrasion, corrosion and premature deterioration. Its polymer coating and OEM-compatible fittings are designed to provide a reliable, watertight pathway that helps maintain proper water flow, appliance performance and minimizes the risk of leaks that can lead to property damage.
Timely and accurate diagnosis of inlet-hose condition is important to preserve appliance reliability and prevent water-related incidents. Regular visual inspection for cracks, bulges, mineral buildup or visible wearand monitoring for leakage during operation, will indicate when replacement is warranted. When issues are identified, fitting an appropriate replacement like the WX14X10005 two-pack-selected for correct length and compatible fittings-or engaging a qualified technician ensures the repair restores safe, dependable operation.
using a quality, OEM-compatible inlet hose and replacing it promptly when diagnostics reveal deterioration are practical, low-cost measures that protect the washing machine and surrounding property. Routine checks and correct replacement procedures support long-term performance and reduce the likelihood of unexpected failures.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
