WB08T10002 GE Oven âCooktop Lamp 40W 120Vâ Bulb is⣠an âappliance âillumination lamp⣠specified â˘for use in âGE⢠oven and cooktop assemblies; it isâ a 40-watt, 120-volt lamp intended to provide⢠interior lighting in âŁhigh-temperature cooking environments.â As a âpurpose-built appliance lamp, it is⢠designed to fit âinto âthe oven/cooktop lamp holder and⤠to withstand theâ elevated âŁtemperatures and cyclic thermal stresses that occur during â˘normal oven and cooktop⣠operation.
Inside theâ appliance⢠the lamp âprimarily â˘provides interior visibility for the âcooking cavity âand interactsâ electrically and mechanically with the lampâ socket,⤠wiring harness, door switch or control logic (depending on â˘model), âand âŁany protective glass or lens assemblies. âBecause it operates in a⣠hot environment, compatibility âwith the socket type, â¤voltage,â wattageand heat-rating of surrounding â¤components is vital; incorrect⤠lamps âor damaged âsockets can â¤cause⤠intermittent operation, overheatingâ of the âŁsocket assembly, âŁor premature lamp failure. The lamp’s⢠behavior is âtherefore relevantâ not only âfor user convenience but alsoâ for safe,⤠reliable appliance operation and serviceability.
In this article you will âfind â˘a technical overview of the â˘lamp’s function and typical installation locations, guidance on compatibility and how to â˘verify âcorrect⤠replacement parts, common⤠failure symptoms â¤to recognizeâ (for⣠exampleâ no illumination, flicker, âŁblown filamentor damaged glass), basic⣠troubleshooting⢠steps â˘to isolate electrical versus lamp faults, âand â¤practical replacement considerations such âŁas matching âelectricalâ ratings, inspecting⢠theâ socket and wiring,⢠safeâ handling and power-disconnect proceduresand⤠notes on OEM versus equivalent part selection.
Table of Contents
- Function and Operational Role of the Cooktop⤠Lamp â˘in GE Ovens
- How the WB08T10002 GE Oven Cooktopâ Lamp 40W 120V⤠Bulb Integrates with the Oven’s Electrical, thermaland Control Systems
- Common Failure symptoms,⢠Visual Indicatorsand Diagnostic Tests for Cooktop Lampâ faults
- Compatibility,â Replacement⣠Specifications, Installation Procedureand â˘Post-Installation Testing
- Q&A
- Closing Remarks
Function and Operational Role of the Cooktop Lamp â¤in GE Ovens
Theâ WB08T10002 GE⤠Oven Cooktop Lamp 40Wâ 120V â˘Bulb â˘is a small⤠incandescent illumination source⤠designed to provide focused light onâ the cooktop area â¤withoutâ affecting â˘cooking controls. Electrically it presents a nominal âŁload⢠of 40⤠watts⢠at 120 volts â(approximately â0.33 âŁAâ steady-stateâ current)and its filament-based design produces both âvisible light â˘and a modestâ amount of radiant heat. The lamp is installed â¤into a sealed âor shielded lamp holderâ located under the cooktop surface⣠or⣠within âŁthe range trim; the⢠enclosure andâ any protective lens â¤areâ integral to keeping nearby thermoplasticâ components and wiring within their temperature ratings while allowing â¤the lamp to perform under elevated ambient temperatures commonâ in ranges and âovens.
For service and⤠compatibility,⢠replace only with a lamp thatâ matches the original âpart specification and physical fit to avoid overloading the lamp circuit âor âraising enclosure temperatures. â˘Common service symptoms that âŁindicate lamp âor holder issues include âintermittent âoperation, visible darkening of â˘the bulb envelopeor no light despite 120 V present atâ the socket; these symptoms typicallyâ point toâ filament â˘failure, a degraded lamp⢠holderor a âfaulty switch. â¤Technicians â¤commonly verify lamp function by measuringâ socketâ voltage with⣠the control activated, confirming continuityâ of the bulb filamentand inspecting⤠the⤠assembly â˘for heat-related degradation. âPractical examples: installingâ a higher-wattage lamp can accelerate surroundingâ material aging and cause tripped⣠thermal cutouts, whileâ using the correct WB08T10002 bulb preserves intended â¤illumination level and thermal âmargin in the â¤cooktop assembly.
- Key features: 40 W⤠power, 120 V nominal â˘supply, filament incandescent source, âinstalled in an enclosed âcooktop lamp housing.
- Common failure indicators: flicker, darkened âbulb surface, âopen â˘filamentor loss of light with voltage present.
- Service notes: match wattage/voltage and physical fit; â˘isolate power before replacement and inspect holder and⢠wiring for heat âdamage.
| item | Description |
|---|---|
| Wattage | 40 W |
| Voltage | 120 V |
| Nominal current | â0.33⤠A |
| Typical âlocation | Sealed cooktop lamp housing / trim under âŁthe cooktop âsurface |
How the â˘WB08T10002 GE Oven Cooktop Lamp 40W 120V Bulb integrates with the Oven’s electrical, âThermaland â¤Control Systems
The WB08T10002 GE â¤oven â¤Cooktopâ Lamp 40W 120V Bulb is a 40-watt,⤠120-volt incandescent-style appliance lamp that connects âŁinto the oven’s dedicated light âcircuit and socket assembly. Electrically it draws approximately 0.33 â¤A at nominal voltage and âis typically wired toâ the ovenâ chassis through a â¤two-conductor harness and socket; activation is handled by the âoven âlight switchâ or⣠the oven control board â(some⤠models energize the lamp automatically when the door is opened). Compatibility â¤depends âŁon matching the voltage,wattage,and socket type⤠and⢠using a lamp⢠rated forâ elevated ambient temperatures found inside the oven cavity; installing a⤠bulb with âŁa lower temperature rating or âincorrect wattage⤠can âcause premature failure or overstress the lamp â˘housing and wiring. â¤For technicians,a âsimple verification is to measureâ line voltageâ at the socket⢠when the lamp shouldâ be on to isolate âlampâ versus circuit failures before replacing âcomponents.
Thermally theâ lamp âŁoperates âwithin a heat-resistant⤠enclosure⤠and typically âŁbehind theâ oven’s inner glass, so its ownâ heat âoutput is minor compared with heating elements but⣠can âproduce⤠localized thermal loading near nearbyâ sensorâ probes or⤠insulation. Control systems ânormally isolate the lamp circuit from⢠heating elements âwith âseparate relays or switches, so a âlamp fault should not directly affect bake/ â¤broil functions; however, âa⤠short or wiring fault in the lamp circuit can âblow â˘a fuse or trip a safety device that affects other circuits. âŁWhen considering LED replacements, choose high-temperature â˘appliance-rated LEDs and âverify they do not interfere with â˘control-board diagnostics⢠or require additional load âcompensation. Commonâ practical⢠troubleshooting steps include checking for âŁa â˘failed â˘filament, corroded socket contacts, faulty doorâ switchorâ blown thermalâ fuse; a multimeter and visual âinspection ofâ the housing â¤and wiring typically resolve whether the issue is the WB08T10002 component or â˘an⢠upstream control/electrical fault.
- Electrical âload and wiring: 40W at 120V (~0.33 A)â with a dedicated âŁlamp⤠harness andâ switch/relay control.
- Thermal environment: mounted behind â˘heat-resistant glass, designed for elevated oven âcavity temperatures.
- Control⢠interaction: isolated from heating elements⢠but tied âinto door switchesâ and the controlâ board forâ on/off behavior.
- Compatibility considerations:⤠socket âŁtype,wattage/voltage match,and⣠high-temperature rating â¤are required for safe operation.
| Item | Description |
|---|---|
| Rated power | 40⢠W |
| Ratedâ voltage | 120 V AC |
| Nominal current | ~0.33 A |
| Typical mounting | Socket inside lamp housing behind oven inner glass |
Common âŁFailure Symptoms, Visual Indicatorsand Diagnostic Tests for Cooktop⤠Lamp Faults
The WB08T10002 GE Oven âCooktop lamp 40W 120Vâ Bulb is a lowâvoltage âincandescentâ illumination component âdesigned âto provide localized lighting inside â˘the cooktop/oven cavity; it must â˘be replaced⤠with⢠a lampâ that matches the⤠120 V â˘rating, 40 W power drawand the correct â¤base type â¤for safe operation. Common failure symptoms include a complete loss of light (open filament), âintermittent flicker (poor⣠contact at the socket or a partially âfractured filament), noticeably reduced lumen â¤output (filament thinning or âinternal blackening)andâ visible âglass⤠or base damage. Visible blackening or a sagging âfilament inside â¤theâ bulb usually indicates⤠endâofâlife caused by tungsten migration,â while scorching or⤠melted socket insulation points toward overheating or incorrect â¤wattage âŁselection for theâ appliance enclosure. Forâ practical âtroubleshooting, a failed lamp should be compared against a knownâgood⣠replacementâ to isolate whether the issue isâ the lamp or the oven’s supply/switching circuit.
- Visual checks: cracked glass, âfilament discontinuity, blackened interior, corroded âŁor bent center contact in the socket.
- Continuity test: with power removed,â measure⣠filament resistance with a multimeter (expectâ cold resistance roughly â¤25-40â Ί for a âtypical 40 W âŁincandescent; hot⤠operating âresistance⤠â 360 Ίand operating currentâ â 0.33 A).
- Voltage test: with the circuit energized and bulb removed, verify ~120⢠VAC at theâ socket toâ rule out wiring, door switch,⣠or control⣠faults (use appropriate insulated âŁprobes âand safety PPE).
- Functional substitution: â¤fit a knownâgood 40W/120V⢠bulb⤠to⢠separate lamp failure from electrical âŁfaults; if the good bulb works, replace the original âlamp.
- Inspect surrounding components: âcheck the lamp holder, door interlock switchand any thermal cutouts for continuity or intermittentâ contactâ if symptoms persist.
| Item | Description |
|---|---|
| Expected operating current | â 0.33 A (40 W / 120 âV) |
| Hotâ operating⢠resistance | â âŁ360 Ί (calculated from V²â / P) |
| cold filament âresistance (multimeter) | Typically ~25-40 Ί; significantly higher or open = filament â˘break |
Interpreting diagnostic results: an intact continuity reading combined with noâ voltage at theâ socket indicates a supply, switchor wiring fault;⢠voltage âpresent âat theâ socket⤠with an open âfilament â¤confirmsâ lamp failure and justifies replacement.⣠Intermittent lamp operation that reproduces under gently âmanipulating the â˘socket usually indicates â˘mechanical contact fault or âŁdegraded âcenter contact tension and may beâ resolved by socket replacement rather than repeatedly replacing â˘bulbs. Disconnect power âbefore performing continuity checks,and âŁwhen measuring live voltage use a suitable voltmeterâ and insulated tools; replacing â¤theâ lamp with one â¤that âmatches the⣠original âspecification âprevents overheating ofâ the lamp âŁhousing and reduces risk â¤of premature â¤failure.
Compatibility, Replacement âŁSpecifications, Installation âProcedure, âandâ post-Installation Testing
The WB08T10002 â¤GE⢠Oven âŁCooktop Lamp â40W 120Vâ Bulb is an appliance-grade incandescent lamp engineered to⣠provide cavity illumination whileâ tolerating⢠thermal cycling, âŁvibrationand proximity to food vapors common âin oven and cooktopâ enclosures. Its 40 W, 120â V rating⣠matches the original⢠equipment specification⣠for the models that list thisâ part; the⢠lamp usesâ a heat-resistantâ envelope andâ a base designed for⣠enclosed appliance sockets rather than general-purpose household fixtures. Compatibility depends⢠on socket form factor,⤠clearance behind the protective lensand⣠the fixture’s rated⢠maximum â¤wattage – verify the⤠appliance parts list âŁor lamp socket dimensions before replacingâ to ensure fit and thermal compatibility with the lamp housing and lens assembly.
- Disconnect âmains power and allow the appliance to cool completely.
- Remove the⢠protective lens or âcover, then extract the old⢠lamp and⣠inspect theâ socket for corrosion or degraded insulation.
- Install âthe⢠WB08T10002 lamp, avoiding contact with the â¤glassâ envelope if possible, reseat the cover/gasketand â˘restore power.
- Perform post-installation âchecks: confirm steady illumination, verify the door/light switch âoperates correctlyand observe for⤠flicker or overheating duringâ a short run.
During installation, confirm mechanical clearance so the lamp⤠does âŁnot contact food or insulation and that the cover gasket provides a sealâ against grease; âa loose lens or degraded gasket can accelerate lamp failure. For diagnostics, âuseâ a⤠multimeter to check for ~120 V âŁat the socket ifâ the new lamp doesâ not lightand verify continuity of the door âswitch âandâ wiring harness.⣠After installation,a practicalâ test is to run the oven light⣠through⣠normalâ cyclesâ and â˘observe âŁthe lamp for stable brightnessâ and absence⢠of arcing or discoloration; persistent⤠dimming or âintermittent â˘operation indicates socket damage or intermittent supplyâ and warrants replacing the socket âor contacting⤠a technician.
| Item | Description |
|---|---|
| Part | WB08T10002 â¤GE â˘Oven Cooktopâ Lamp 40W 120V Bulb |
| Wattage / Voltage | 40 W, 120â V (incandescent appliance lamp) |
| Typical âconsideration | Appliance-rated envelope and base; â¤verify socket compatibility â¤and lens clearance |
Q&A
What is the WB08T10002 bulb?
The WB08T10002 is a 40 watt,â 120 volt appliance/incandescent⣠lamp sold âas a âreplacementâ lightâ for certainâ GEâ ovens and⣠cooktops.⤠It is designed andâ rated for use âinside an oven or â¤appliance⣠light âcavity where higher ambientâ temperatures occur and âisâ intended to be used with the oven’s protective âlampâ cover.
How do⣠I â˘know âif this bulbâ willâ fit âmy oven?
Compare the⢠part number on your⣠existing bulb or the âbulb âcover/owner’s manual with WB08T10002. Also verify⢠the⣠required voltage âand wattage (120 V, 40 W) and that the⣠physical shape â˘and baseâ match your socket. If⤠the part âŁnumber isn’t printed on yourâ oldâ bulb, consult âyour⤠oven’s model-specific parts listâ or the manufacturer’s⤠website to confirm⢠compatibility.
What is the âcorrect procedure⤠to replace the WB08T10002 bulb?
Allow the oven âto cool completely, then switch power to the appliance âŁoff (at the controls or breaker) for safety. âŁremove âthe protectiveâ lamp coverâ (usually by âunscrewing or releasing clips), gently unscrew the old bulb counterclockwise â˘using a cloth or glove, installâ the new â¤40 âŁW/120 âVâ bulb, âreplaceâ the⢠cover, restore⢠powerand test. Avoid⤠touching the â˘glass with bareâ hands while hot âor â¤when using â˘halogen-style bulbs; for an incandescent oven lamp this is less critical but still best practice.
Can I replace the WB08T10002⢠with âan âLED bulb?
Only âif âthe LED âis specifically⢠rated for âoven/appliance high-temperature⤠use and matches âŁthe socketâ typeâ and electrical specs. âMost general-purpose LED⣠bulbs are not âdesignedâ for the high temperatures insideâ an â˘oven and will fail âor âbe unsafe. If âŁyou want âan LED,purchase an oven-rated âLED replacement explicitly âspecified for use inside ovens âand confirm the â˘base and voltage match.
Why does the oven bulb â˘burn âŁout frequently?
Frequent failure can be caused by vibration⣠from⣠the oven âdoor or âracks,⢠a loose⤠or corroded socket causing arcing, âŁexcessive oven temperatures (faulty⣠thermostat or broil element), moisture⤠gettingâ intoâ the âlamp cavityor âusingâ the incorrect bulb type. âŁInspect the socket and lamp cover, make sureâ the⤠bulb is properly seated, âand verify⣠the oven is heatingâ normally. âIf problems persist, have â¤a technician inspect the lamp circuit and âcontrols.
Is the WB08T10002 safe to â˘use near the âbroiler or âon⤠the âcooktop?
The bulbâ is designed for use in the â¤oven light or appliance â¤light housing â¤with theâ protective âcover in place. â¤It is ânot intended to be directlyâ exposed to open flames, direct broiler contactor placed where itâ would âbe in direct⣠contact with food or liquids. Follow the appliance manufacturer’s instructions regarding lampâ placement and protective covers.
What wattage and voltage should Iâ use as a replacement?
Replace⣠with⤠the same electrical rating: 40 watts and 120 volts, unless the appliance manufacturer’s âdocumentation specifies otherwise. Using â¤aâ higher-wattage âbulb can overload the socket, generate excessive heatand damage wiring orâ the lamp housing. âŁA lower-wattage bulb will reduce illumination⤠but is generally safe ifâ it fitsâ and is the correct voltage.
Where âcan I buyâ a replacement WB08T10002 bulb and is âit an⤠OEM part?
WB08T10002 is sold⤠as⣠an OEM replacement âŁfor GE appliances and is available from GE partsâ dealers, â¤authorized appliance parts retailersand â¤many âŁonline stores.⤠You⢠may also⤠use an equivalent bulb⢠fromâ a âŁreliable⤠supplier as long as it matches the OEM specifications (40 âW, 120 V and designed⤠for appliance/oven use).
Closing Remarks
The WB08T10002 âGE Oven Cooktop â¤Lampâ 40W 120V bulb plays â¤a small but important ârole in everyday appliance use â˘by providing reliable, âfocusedâ illumination for⢠monitoring cooking progress âand maintainingâ a safe, functional cooktop â˘or oven environment. Designed âto match the electrical and thermal⤠requirements of the appliance,the âcorrect bulb supports visibility for tasksâ such as checking browning,spotting spills,and ensuringâ even,safe operation without â˘introducing â¤undue stress to the fixture or wiring.
When lighting issues⢠arise, careful âdiagnosis and timely âreplacement are essential â¤to preserve performance andâ safety. âConfirming compatibility with the âappliance, inspecting the âŁlamp and socketand â˘following â¤manufacturer guidance or seeking⢠qualified âservice when⣠needed will reduce the risk of âimproper installation or electrical problems. Routine checks andâ responsible replacement of the WB08T10002 or an approved equivalent help maintain the⣠appliance’s âŁfunctionality and contribute to a safer⣠cooking environment over time.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
