137311900 Frigidaire Washer Pumpâ is a âspecific drain pump assembly usedâ in Frigidaire âŁwashing machines; it is an electromechanical component that combines a smallâ electric motor, an impeller âŁand aâ molded housing to move wash and rinse water out of âthe âŁtub and into theâ household drain. As a⤠mechanical subsystem ofâ the appliance,⣠the pump typically â¤mounts⤠to â¤the base or⣠sump area of the washer⤠and âŁprovides the⤠hydraulic â¤flow âand pressureâ required during drain and spin cycles. the component is identified âby â˘its â˘part ânumber to ensure âproperâ fit,⣠electrical characteristics and mounting alignment when⢠servicing or replacing the unit.
Inside the â˘appliance the pumpâ interfaces directlyâ withâ the tub/sump, drain hose and âexternal plumbingand it⢠is controlled âŁindirectly âŁby the âwasher’s main â˘control board and âŁwater-level â˘or pressure sensingâ systems. Whenâ the âcontrollerâ issues a drain command the⣠pump motor receives power through the wiring⢠harness and discharges water throughâ the outlet â˘port; in âaddition, theâ pump can affect otherâ operationalâ subsystems such â˘as spin speed and cycle progression because incomplete drainage will⢠prevent âcertain âcycle âŁtransitions. Theâ pump⤠must also maintain a â¤seal âagainst theâ wet chamber to prevent leaks andâ protect âadjacent electronics and structural components.
In this article readers will âŁfind a technical⣠overview of the 137311900 pump’s function â¤and typical installation âŁlocations,â guidanceâ on confirming model⤠compatibility and electrical specifications, common failure symptoms to⤠watch â¤forâ (such âŁas âno-drain, humming, intermittent âŁoperation or leaks)and structured troubleshooting checks such as visual inspection, obstruction clearingand basic âelectrical tests. The articleâ will also cover practical replacementâ considerations – including gasket and âhoseâ clamp âcondition,correct mounting orientation and torque,and safety precautions such as disconnecting power and water before âserviceâ -⣠so⢠technicians,engineers and informed appliance owners can â˘make accurate⣠diagnostics âŁand âreplacement decisions.
Table of âContents
- Function⢠and Role ofâ the Washer Drain Pump â¤in Frigidaire Laundry Appliances
- How theâ 137311900 Frigidaire âWasher Pump Works: Motor, Impellerand Drainageâ Circuit
- Common⤠Failure âSymptoms⢠and Measurement-Basedâ Diagnostics for Pump Faults
- Compatibility, Replacement â˘Considerations, âand âStep-by-Step Installation for the Pump
- Q&A
- Wrapping Up
Function and Role of âthe â˘Washer âŁDrain Pump in Frigidaire Laundry Appliances
The 137311900â Frigidaireâ Washer Pump is⣠an electric motor-driven âdrain⣠assembly that âremoves wash and rinse â˘water from the â¤tub during drain andâ spin âŁphases. It uses an⣠impeller housed in â¤a molded pump body to convert motor torque into hydraulic⤠flow; when theâ washer’s âcontrol board applies power the impeller forces water through the tub outlet and drain hose.Proper component replacement requires matching the pump’s mechanical mounting, electrical connector pinout, âimpeller orientation âand⣠hydraulic characteristics â(flow rate vs.head) âto the specific Frigidaire model to âmaintain designed drain performance and preventâ overloading the motor orâ creating back-pressure â¤in âŁthe plumbing.
- Common symptoms âof a failing pump:⤠no drain,slow âdrain,loud grinding or buzzing,or external leaks from the âpumpâ housing âŁor seals.
- Basic diagnostics: verify electrical⤠supply to theâ pump⣠during the⢠drain cycle,check⢠motor â˘winding continuity,inspectâ and clear foreign⢠debris from the impeller and filter,and⣠confirm the â˘impeller rotates freely âwhen the motor is unpowered.
- Compatibility âchecks: â¤confirm mountingâ flange, hose diameter, connector âtype and the pump’s hydraulicâ capacity match theâ appliance before âinstallation.
| item | Description |
|---|---|
| Part | 137311900 Frigidaire washer Pump⤠– motor âand impeller âdrain assembly |
| function | Evacuates tub water during drain and spin âŁcycles by convertingâ motorâ rotation into â¤flow |
| Installation note | Verify electrical connector, mechanical fitand hydraulic capacity âfor the â¤specific washer model |
In service situations, technicians should isolate the pump electrically and mechanically before testing:⢠measure voltage⣠at⢠the connector â˘with the appliance â¤in a âdrain program, thenâ check motor continuity with â˘aâ multimeter and inspect theâ housing for trappedâ garments or hard debris. âA humming â¤motor âwithâ no âimpeller movement âŁtypically indicates a âseized rotor or jammed⤠foreign object; noisy bearings or persistentâ leaks warrant replacement rather than repair. Forâ appliance owners,â simple preventive maintenance-clearing the pump access âfilter and ensuring â˘drainâ hoses are â˘free of kinks-reduces âtheâ likelihood of premature â¤pump failure and helps maintain reliable operation.
How âthe â137311900 frigidaire Washer âPump âWorks: Motor, Impeller,â and drainageâ Circuit
The 137311900 frigidaire Washer â¤Pump âis a compact, sealed singleâphase electric motor assemblyâ that drivesâ aâ molded centrifugal impeller to âŁevacuate wash⤠water from the âtub through the discharge hose. The pump mounts to the washer base with a⤠direct âmechanical interface⢠and⤠a molded inlet that aligns⣠with â˘theâ tub drain; electrical power â¤is supplied from the âwasher control board via a âŁdrain⣠relay or triac so⣠the pump⢠runs only during drain and spin cycles. Internally the motor shaft âcarries a small plasticâ impeller inside a âvolute housing; a shaft seal âand integrated strainer protect the motor âfrom bulk âŁdebris and moisture. Correct⣠fitment requires matching the mechanical flange, electrical connector, âŁand discharge orientation supplied onâ compatible Frigidaire models, so the â¤137311900 unit is â¤used were OEM dimensional and electrical â¤specifications are required for reliable⤠installation.
Functional behavior â˘and⣠commonâ failure modes are straightforward to diagnose: the motor should spin freely and produce a steady flow out the âŁdischarge; ârestricted flow, reduced speedor complete failure âŁmost âfrequently⤠enough results âfrom impellerâ damage, debrisâ jams in the â¤voluteor âloss âof the startâ circuit in the motor. A⣠humming⤠motor with no â¤rotation â˘frequentlyâ indicates a seized impeller orâ a failed start winding while visible damage to vanes causes âŁcavitation â¤and poor drainage.⤠Technicians typically verify â¤continuity âand winding â¤resistance, inspect⢠the volute for foreign objects,â andâ confirm that â¤the control board is supplying mainsâ voltage during the⤠drain â¤command (e.g., ~120 V AC in North American machines)⤠before replacing â¤the pump. â˘Replacing the assembly restores correct hydraulic performance when the motor and impeller areâ the root âcause; âif symptoms âpersist, check â¤downstream hoses, clampsand check valves for â¤restriction or backflow.
- Key behaviors: â¤intermittent ârun âŁonly â¤during drain cycles, direct âmotor drive toâ centrifugal impeller, protected by⤠strainer and shaft â˘seal.
- Symptoms of failure: no⢠drain, slow drain, humming, loud âŁgrinding,â or leaking at pump housing.
- Practical â˘test: âmeasure windings, âŁvisually âinspect volute, confirm control voltage⢠before bench powering.
| Item | Description |
|---|---|
| Motor â¤type | Sealed singleâphase âŁelectric âmotor designed for intermittent duty in washer drain âcycles |
| Impeller | Molded centrifugal impeller; âplastic vanes sized for⣠lowâhead, highâflow drainage |
| Electrical interface | Connector âto washer control (drain relay/triac); operates âonâ appliance mains (model dependent) |
| Common faults | Debris jam, impeller damage,â shaft seal failure, âmotor start winding failure, electrical â˘connector⣠faults |
Common Failure Symptoms and Measurement-based â˘Diagnostics for Pump Faults
The drain pump on many â˘Frigidaire washers âis a⢠small centrifugal motor-impeller assembly that evacuates tub⢠water through âa âmolded housing; replacement units such as⤠the 137311900 âFrigidaire Washer Pump share the same electrical connector and mounting footprint used across several Frigidaire âtop-load models, â˘but verify harness type and mounting tabsâ before installing. Failure modes⤠are primarilyâ mechanical (blocked or broken impeller, worn bearings, sealâ failure) âor⤠electrical (openâ windings, short to ground, â¤or âloss of⢠drive voltage). Mechanical faultsâ typically âpresentâ as â˘reducedâ flow or grinding noises, while electricalâ faults produce no-spin or a constant hum; compatibility checks⢠should include âŁconnector pinout, mounting orientationand âŁdrain hose alignment to avoid⣠improper â˘installation that can mimic pumpâ failure.
Use measurement-based diagnostics âŁto separate mechanical from electrical causes:⤠confirm the controllerâ is commanding the pump â˘(measure expected drive âvoltage at âŁthe âpump connector during⢠a drain âŁcycle), then check the motor windings with a multimeter for continuity and insulation. A âworking pump will â¤show a low-resistanceâ winding and⤠no continuity â˘between windingâ and chassis ground; a completely open â¤winding indicatesâ a burned âmotor, while â¤a short-to-ground âŁindicates insulation âŁfailure. If voltage is present but the rotor⣠does not turn âŁand the â˘winding resistance is within ârange, âŁinspect the impeller and pump housing for âdebris or seized bearings. If the pumpâ draws excessive current when powered, that suggests mechanical bindingâ or âinternal friction â¤rather than an â¤electronic control âfault.
- No⤠drain or slow drain
- Continuous humming with âno ârotation
- Loud grinding, rattlingor vibration
- Water leakage from pump area or connector
- tripping the⢠household circuit or trippingâ washerâ motor protector
| Item | Description |
|---|---|
| Continuity | Low resistance âacross pumpâ motor leads âindicatesâ intactâ windings; open = failed winding. |
| Resistance | Typical⤠static winding resistance is approximately 10-50â Ί (varies by motor); consult âmodel â˘service data⢠for exactâ spec. |
| Applied voltage | Measureâ at connector⢠during drain⢠command; âtypically nearâ mains voltageâ (commonly ~120⤠VAC in North America). |
| Insulation | No âŁcontinuity between â¤winding and chassis ground; any continuity indicatesâ leakage and requires â¤replacement. |
| Current draw | Normal running current isâ modest; aâ marked increase âon⣠start or during â¤run implies mechanical binding⢠or defective bearings. |
Compatibility, Replacement Considerationsand step-by-Step Installation for the Pump
The 137311900 âfrigidaire Washer⤠Pump serves as the drain/recirculation assembly thatâ evacuates⢠wash and rinse⤠water from the⣠tub â˘and routes it to the⣠household drain.â Functionally, the⢠unit combines an impeller, motor, âŁand molded housing;â compatibility depends on âmatching the housing inlet/outlet⤠locations, mounting flange pattern,â electrical connector typeand â¤hose diameters rather⤠than just â¤the part number. â¤when selecting a replacement,⤠inspect the old â˘assembly for the number of electrical âleads, connector styleand the orientation of⢠the discharge âŁport; aftermarket substitutions with â˘different â˘motor âspeed, impellerâ geometryor misaligned outlets can cause insufficient draining,â vibrationor leaks⢠even if the pump physically fits the mounting points.
| Item | Description |
|---|---|
| Nominal supply | 120 V AC â˘typical in North american models – verify⣠label on chassis |
| Connector | Two- or three-pin quick-disconnects; âŁconfirm terminal âŁspacing and keyed orientation |
| Hose âinterface | Standard⤠washer âhose diameters; check diameter and clamp type before reuse |
Installation requires intentional sequencing toâ avoid damageâ and⣠ensure a watertight âresult:⢠disconnect power ⢠at the breaker and drainâ residual water beforeâ loosening hoses,⣠remove clamps and wiring in âa manner that preserves terminal orientation labels, then unfasten mountingâ screws and extract âthe old⤠pump while supporting its weight. During â¤reassembly, verifyâ the pump â˘housing gasket andâ impeller rotate freelyorient the⣠discharge âcorrectly to avoid⣠kinking hosesandâ torque âfasteners to manufacturer recommendations; after reconnecting wiring and clamps, restore power briefly to run a short drain cycle and check forâ leaksâ and properâ flow.
- Turn off power at⢠the â˘breaker âand unplug machine if⢠accessible.
- Open the service âpanel âand position âtowels to âcatch residual water.
- Disconnect âŁinlet/outlet âhoses and remove clamps; note hose locations.
- Label âand â˘disconnect electrical connectors from the pump motor.
- Remove mounting⤠screws and extract the pump assembly.
- Install new pump, âalign ports, secure âmountingâ screws, â˘and reconnect â˘hoses with new clamps⣠if â˘needed.
- Reconnect electrical âterminals in original orientation and ârestore â˘power for testâ cycle.
- Inspect for leaks âand abnormal noise; re-torque clamps and âfasteners if necessary.
Q&A
What is⢠the 137311900 Frigidaire washer⢠pump and âŁwhat does it⢠do?
The 137311900 isâ an OEM drain pump⤠assembly âusedâ on many âFrigidaire washing â¤machines. its primary job isâ to remove water â˘from⣠the â¤tubâ during the â¤drain and spin âportions of⤠the wash⣠cycle⣠by pumping water out through the drain âhose to your householdâ drain.
whatâ are common symptoms â¤that the 137311900 pump is failing?
Commonâ signs include: washer does not drain or drains slowly,standing water in⣠the tub,loud grinding âŁor rattling â˘noises during drain,the pump leaks,or washer displays drain-related error codes. The âŁpump motor may also hum⤠without moving â¤water if the impeller is jammed orâ the motor windingsâ areâ failing.
Howâ canâ I safely test whether the pump is bad?
First unplug âŁtheâ washer and drain anyâ water from âthe tub. Inspect the pump and hoses âforâ visible clogsâ or damage. Use aâ multimeter to check âfor electrical⢠continuity across âthe pump terminals-continuity⣠indicates⣠the motor windingsâ are intact; an open â˘circuit indicates a⣠failed motor. âOnly experienced technicians⢠should test for live voltage (usually â˘120 VAC)⤠while the machine âis running; if you⣠do, take safety precautions âto avoid shock.
What should I check before replacing the pump?
Before replacing theâ pump, clear and inspectâ the⢠drain hose, standpipe,â and any access filter/trap âfor blockages. Remove the pump and â˘check⤠the impeller for trapped objects (coins,⤠socks,â glass)⢠and try to â˘spin it manually. Also verify that â¤the washer’s drainâ solenoid/lid switch and control board âare sending⢠power â¤to theâ pump,becauseâ anâ electrical⢠fault⣠elsewhere can â˘mimic a bad⤠pump.
howâ do I⢠replace âthe 137311900 pump (basic steps and tools)?
General replacementâ steps: unplug the washer and turn off water. Access⣠the pump (typically via âthe⣠front or⤠rear â¤lower âaccess panel), âplace a shallow pan⣠or towels to catch residual âwater, âdisconnectâ electrical connectors âŁand âŁdrain⤠hoses, remove mounting fasteners, swap in the â˘new pump, reconnect hoses âand⣠wires,â secure theâ panelandâ run a short drain/spin â˘cycle to test. Tools commonly⤠needed: âscrewdrivers,â pliers, nut âdrivers,â and âhose clamps. Always follow the washer’s service âmanual for model-specific instructions and safety precautions.
Why is the pumpâ making loudâ grinding or⢠rattling noises and can I fix it without replacing it?
Noisy⣠operation is often caused âby foreign objects caught in the âimpeller, a damaged impelleror worn âmotor bearings. If the ânoise âisâ fromâ debris, you can often clear it â¤by removingâ the pump and âextractingâ theâ object.â If the impeller or motor bearings â¤are damaged, the pump usually⢠needs replacement âbecause â¤those components â¤are â¤not⣠typically serviceable separately.
Is the⤠137311900 pump compatible with my specific âFrigidaireâ washer model?
Compatibility â¤depends on the washer model. â¤always check theâ washer’s âexact model and⢠serial â˘number andâ cross-reference with Frigidaire’s parts âlist âor âanâ authorized parts supplier. Part numbers are⣠sometimes superseded âor listed under different OEM numbers, so verify compatibility⤠before purchasing.
How long does a drain pump⤠like âtheâ 137311900 typically last and is it worthâ replacing?
Drain pumps can last many years â(often âŁ5-12 years) depending on usage, water quality,⢠and whether â˘foreign objects enter the pump. Replacing â˘a failed pump is typically more cost-effective than replacing the â¤entire washer,especially if the machine is or else in good â¤condition. âConsider the age⣠of theâ washer,cost of â¤the part and labor,and whether⢠other components are⣠near⣠end-of-life whenâ deciding.
Wrapping Up
The 137311900 Frigidaire washer pump⣠is a key component in âŁthe⢠appliance’s drainage system, responsibleâ for removing water at⢠the end of wash and rinse cycles. âItsâ reliable operation supports overall wash performance, prevents standing water⤠and âŁpotential leaksand⢠contributes to the longevity and efficiency of the⤠washer. Failures or⣠restrictions in âthe pump can produce audible symptoms, incomplete drainsor fault codes, making it a common âŁfocus during troubleshooting of drainage-related issues.
Accurate diagnosis is essential⣠before replacing the 137311900 Frigidaire âwasher pump: distinguishing between a failed⢠pump, aâ clogged hose â¤or filterandâ electronic âor control issues⢠avoidsâ unneededâ parts replacement and additional⢠labor. âŁWhen replacement⤠isâ required,using⢠the correct pump model â˘or an â¤appropriate manufacturer-recommended alternative,following safety procedures⤠(power and waterâ isolation),and verifying proper installation and testing afterward⤠will help restore performanceâ and reduce âthe ârisk of repeat faults.For â¤complex problems⢠or whenâ safetyâ andâ warranty considerationsâ apply,consultation with a qualified service â˘technician is âŁadvisable.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
