316580611⣠frigidaire âIgnitors Harness is a specific wiring assembly used in Frigidaire gas â˘cooking appliances; it is indeed a connector and insulated lead set that⣠links the ignitor element â˘to the appliance control and gas valve circuit.â As a targeted electrical component, the harness consists of terminals, highâtemperature insulation and strain relief features designed to operate in the elevated temperaturesâ and confined routing typical of ovens, rangesâ andâ broilers.
Inside the appliance the ignitor harness provides the electrical path⢠that allows the control system to energize⣠the hot surface or spark ignitor and therefore initiate gas flowâ through âŁthe safety valve.â It directly interfaces with the ignitor element, control board/ignition module and gas valveand must⣠maintain low â˘resistance connections and⢠thermal integrity to ensure reliable â¤ignition timing and safety interlocks. Improper routing, insulation failure, connector⢠corrosion or damaged terminals can interrupt currentâ flow âor create⣠intermittent contacts, âŁwhich in turn produce delayed ignition, failed âignition cycles or⤠fault codes reported âby⣠the⢠control⢠system.
In this article âŁyou will find a technical⢠overview⤠of the part’s function âand construction,⢠guidance on model compatibility and identifying the correct replacement, a list of common failure symptoms âto⣠observeand stepâbyâstep troubleshooting checks including visual inspection, continuity and voltage measurements. the article will also cover practical replacement âconsiderations such â¤as heatârating, connector pinouts, âproper â˘routing and securing methods to restore reliable operation and maintain appliance safety.
Table of Contents
- Function and Role of the Ignitor Harness inâ Frigidaire Gas Rangeâ Ignition Circuits
- How the 316580611 âŁFrigidaire Ignitors Harness Works Inside the â˘Appliance
- Common Failure Symptoms and Electrical Diagnostic Indicators âfor ignitor Harness Faults
- Replacement Considerations âand Step-by-Step Installation procedure for⢠ignitor Harness âAssemblies
- Q&A
- Wrapping Up
Function and⤠Role of the âIgnitor Harness in âŁFrigidaire Gas âŁRange Ignition Circuits
The 316580611 Frigidaire Ignitors⤠Harness is a purposeâbuilt wiringâ assembly that⢠links the range’s control/spark module to the burner ignitors â¤and anyâ associated safety switches. In⢠typical frigidaire⢠gasâ ranges âthis harness routes the âcontrol and ground âconductors, âlocates â˘keyed connectors for each electrodeand uses heatâresistantâ insulation toâ withstand proximity âto the cooktop. Functionally, âthe harness does not generate the⣠ignition spark itself; ârather it provides⢠the correct electrical paths and connector â¤interfaces so the spark module and theâ electrodes can operate with⢠correct timing, polarityand isolation from â¤other â¤circuits.
Technicians and appliance owners moast â˘often replace the harness when connectors âŁshow melting,corrosion,or intermittent continuity that causes weak or no â¤spark at one âor more âŁburners. Troubleshooting should⢠include aâ visual⤠inspection for brittle âinsulation and connector damage, a continuity check between â¤mating âpinsand verifying the⤠spark âŁmodule output atâ the harness â˘connector⢠while⢠the control is calling for ignition. Practical compatibility considerations: ensure the replacement harness â˘matches the original connector layout andâ wire count for âyour modeland confirm routing keeps wires away from burner âheat and âmoving parts to prevent early failure.
- Common symptoms⤠of harness issues: no âspark âŁat one or â¤more⤠burners, intermittent ignitionor visible⢠connector overheating.
- Typical checks: visual inspection,continuity test,and verifying proper âŁconnector seating â˘with the spark module and âelectrodes.
- Replacement âŁguidance: match connector type and wire routingâ to the original assembly to maintain safe operation.
| Item | description |
|---|---|
| Wire count | Varies by model; typical harnesses contain multiple conductors for each electrode and common ground/return paths |
| connector type | Keyed plastic male/female plugs âthat match the spark module â¤and⢠ignitor terminals |
| Common failure modes | Heat degradation, â¤connector corrosion, â¤broken strands⤠at crimp pointsand insulation charring |
| Recommended tests | Continuity acrossâ pins, secure connector fitand visual inspection for heat or mechanical damage |
How the 316580611 Frigidaire âIgnitors harness Works Inside the⣠Appliance
The 316580611 Frigidaire Ignitorsâ Harness is a short âassembly of high-temperature insulated conductors and â¤rapid-disconnect terminals that routes mains-level current from theâ appliance control/safety circuit to the oven ignitor. Inside the appliance⤠it provides a secure mechanical and electrical â¤connection between the ignitor element âand âthe gas valve/current-sensing â˘circuit; the harness itself does â¤not â˘create âignition but must conduct sufficient amperage without excessive voltage drop so the ignitor can drawâ the current required to trigger â¤the gas valve. The harness uses matched connector housings andâ wire âgaugeâ to maintain OEM polarity and thermal tolerance,â so compatibilityâ depends on connector shape, pin spacingand insulation⣠temperature rating rather than only wire length or color code.
Electrically, âthe harness behaves as âa low-resistance path whose integrity affects ignitor warm-up time and âvalve⤠sensing. During a normal ignition cycle⢠the ignitor draws high current⣠as it âŁheats; if the harness has corrosion,loose terminals,or melted insulation the resulting increased âresistance can reduce current,extend heat-up time,or prevent the valve from sensing adequate current and opening. Technicians diagnose harness problems by visualâ inspection⢠for heat damage,⢠continuity âchecks across each âconductorand wiggle testing at the connector under power-off conditions. For replacement, select a harness matching the originalâ connector type â¤and wire âŁgauge; in practice⣠replacing a charred orâ open conductor âharness with the âcorrect 316580611 â¤part restores the intended current path and typically resolves intermittent âor non-ignition faults.
- Connector type: quick-disconnect âterminals matched to ignitor and â¤valve pins
- electrical behaviour: low-resistance path critical for ignitor current sensing
- failure⤠signs: open continuity,creasedâ resistance,heat-discolored insulation
- Service note: verify pin layout and insulation temperature rating âbefore swapping
| Item | Description |
|---|---|
| Function | Conducts â˘mains current fromâ control/safety circuit to the⢠ignitor and maintains proper sensing for the gas valve |
Common âFailure Symptoms and Electrical Diagnostic Indicators for⢠Ignitor Harness Faults
The⢠316580611 â˘Frigidaire â¤Ignitors harness is a short wiring assembly that routes control output⤠and supply â¤voltage from â¤the oven control or wiring harness to the ignitor assembly.⣠Its âprimary function is â˘to âpreserve low-resistance connections and proper polarity so the ignitor receivesâ the required current to heat or arc as⣠designed.Common failure modes âinclude open conductors from chafing or broken crimps, high-resistance joints from corroded â¤or⣠overheated terminalsand meltedâ or deformed insulation at high-currentâ connector points.In practice,a degraded harness âŁwill present the same symptoms as a failing⢠ignitor: long glow times,intermittent ignition,orâ complete failure âto light,so technicians should verify harness condition and compatibility against⤠the oven model âand OEM part number⣠before replacing the ignitor itself.
Electrical diagnosis focuses on continuity, resistanceâ under load, â¤and presence of supply voltage at the harness connector âŁwhenâ the control âcalls for ignition. A good harness will show⣠continuity between its mating âpins with very lowâ resistance â˘(typically under â˘a⤠few ohms⤠for âshort leadâ lengths); an open circuit or readings that drift with motion indicate âbroken conductors or intermittent crimps. With âŁthe range powered and a call for heat, you âshould measure â˘near-supply voltage at âthe harness connector (many gas ignitors expect ~120 VAC) and âconfirm the âvoltage does not collapse under loadâ – aâ large voltage drop under â˘load⢠points to high-resistance âconnections in the harness.â Practical checks include a âŁwiggle test to reproduce intermittent âŁfaults, visual inspection for⢠burn marks at terminalsand verifying there is no continuity⣠to chassis ground (which â¤would indicate a short). Always remove power âfor insulation and continuity checks,and follow safe â˘procedures for live-voltage measurements.
- No glow or no ignition despite control calling forâ heat
- Intermittent operation âor ignition only when â¤harness is moved (intermittent continuity)
- Long pre-heat/glow time before flame (voltage drop/high resistance)
- Visible connector corrosion, melted insulationor burnt terminals
- Continuity to chassis ground indicating shorted⤠conductor
| Item | Description |
|---|---|
| Continuity | Low resistance acrossâ harness pins indicates intact conductors; open = broken âwire |
| Resistance under wiggle | Fluctuating or increasing resistance when manipulated suggests intermittent crimps or broken â¤strands |
| Voltageâ at call | Near â˘supply voltage at âconnector when controlâ calls for ignition; collapse under load indicates high-resistance path |
| Short to ground | Continuity between conductor and chassis ground denotes insulation failure or⣠conductor contact with frame |
Replacement âŁConsiderations and Step-by-Step Installation Procedure for Ignitor Harness Assemblies
The 316580611 Frigidaire Ignitors Harness is a factory-style wire assembly that â˘provides the electrical path betweenâ the oven control or ignitor module and the hot surface âignitor. It is designed to carry âthe ignition current⢠and withstand elevated temperatures and vibration near the burner chamber; therefore the assembly is specified by⤠conductor gauge, âinsulation temperatureâ rating, connector type and retention features. Technicians diagnose harness failure by checking for open circuits, high resistance at crimped terminals, brittle or melted insulationand corrosive connector pins-symptoms⣠commonly presenting as no ignition, âlong ignition⣠cyclesor intermittent operation. verify compatibility by â¤matching connector shapes, âpin count,⤠harness length and⤠mountingâ points to the appliance model rather than relying solely on part âŁnumbers, âas â¤minor variations âŁinâ terminal orientationâ or âharness routing âcan prevent correct installation.
Replace the harness following a âcontrolled procedure to avoidâ damaging the ignitor âor introducing unsafe âŁconditions: disconnect power⤠and shut offâ gas âsupply, removeâ access⣠panels to expose the ignitor and wiring,â document the routing and connector positions, detach â¤the old harness âat both the ignitor and control endsand transfer any clips or heat shields to the new assembly. When installing, maintain original routing to keep wires clear of sharp edges and high-temperature surfaces, use⣠proper⢠crimped âor soldered terminations where ârequiredand secure â˘strain reliefs so âconnectors cannot pull âfree during service. After reassembly, ârestore power andâ perform functional checks-observe initial current draw at the ignitor, confirm reliable glow âand âŁflame establishmentâ over multiple âcyclesand⣠scan for fault codes to âvalidate correct operation.
- Pre-replacement checks: continuity⣠test, âvoltage⣠at âconnector during ignition, âvisual insulation andâ connector inspection
- Tools typically required: multimeter, nut drivers, pliers,â replacement clips/heat-shrink as needed
- Post-install âtests:⤠ignition cycle⣠observation, leakage/current âmeasurement,â secureâ mounting verification
| Item | description |
|---|---|
| Wire gauge | Typically âŁ18-16â AWG for ignitor current; verify against OEM specification |
| Connector âtype | Flat spade âor Molex-style⣠terminals;â match shape and latch to control/ignitor |
| Typicalâ resistance | Harnessâ should showâ near 0 Ί; any high â˘resistance at terminals â¤indicates corrosion or poor crimp |
Q&A
What is theâ Frigidaire part 316580611 ignitor âharness and âwhat does it do?
Theâ 316580611 ignitor⣠harness is a wiring âassembly used in gas ranges and⣠ovens that connects the oven ignitor (glow bar or hot surface ignitor)⣠to the oven control and gas valve. âŁIt provides the electrical â˘path and mechanical connector(s) that allow the⢠control to send power to the ignitor during a bake or broil cycle so the gas valve will â˘open once the ignitor reaches the required temperature.
How do I know ifâ the ignitor harness (316580611) is the cause of my oven notâ lighting?
Common signs the harness is bad include visible charring, melted âŁinsulation, broken or corroded connectors, intermittent ignitionor a complete⢠failure to âenergize the ignitor.To isolate the harness, visuallyâ inspect⤠it first, â¤then âcheck for continuityâ with a multimeter. You can also observe âwhether the control sends voltage to the âignitor connector during a call â¤for heat – if voltage is present but â¤the ignitor does not heat, the ignitor itself may be⢠bad; if no voltage is present⢠at the harness,⣠the harness âor control/wiring upstream may be the issue. Always disconnect power and follow safety precautionsâ before testing.
Is⢠the 316580611 harness compatible âwith my âFrigidaire or â¤Kenmore model?
Compatibility depends⤠on âŁthe appliance model and connector style. The 316580611 âis a specific OEM part number used on a range â˘of Frigidaire-built ovens; âmany compatible models are listed â˘by the manufacturerâ or parts â˘suppliers. The safest approach is toâ compare your âŁappliance model number and â˘the harness connectors/length to the part listing or contact⢠Frigidaire/authorized parts dealer. Do not rely solely on visual â˘similarity – confirm withâ modelâ cross-reference to ensure⣠a correct fit.
Can I test the harness with a multimeterand âwhat⢠should I measure?
Yes. With power off and the harness disconnected,use the multimeter to check continuity â¤between the harness ends and to look⤠for open circuits â˘or short to ground. If you need to test operation during â˘a heat call, you can (carefully) measure for lineâ voltage at⤠the harness connector while the oven is calling for⤠heat – this verifies the controlâ isâ supplying power.â If the control supplies voltage but the ignitor does not â¤draw current or heat, the â¤ignitor is likely faulty. Never probe live terminals without proper training⤠and takeâ precautions to avoid shocks or damaging⣠the control board.
How tough is it to replace âthe 316580611 âignitor harnessand what tools do I need?
Replacing the âharness âis generally a moderate⣠DIY job for someone comfortable with appliance repair. required tools typically include a screwdriverâ set or nut drivers, pliers, wire connectors (if splicing)and⢠a multimeter.Steps:⤠disconnect power (andâ gas if necessary), remove the oven access panel or drawer, disconnect the old harness fromâ the ignitor and control/valve, route and secure the â˘new harness away from⣠hot components and moving parts, reconnectand test. Follow the appliance’s âŁservice âmanual for exact disassembly and safety instructions.
should I âŁreplace the harness or the ignitor if the oven won’t light?
Both components should âŁbe evaluated. If the harness shows visible damage (melted âinsulation, burned connectors) or fails continuity tests, replace âthe harness. If the control is supplying proper âvoltage⣠to⣠the harness but the ignitor does not glow âor draw rated current, âreplace the ignitor. Often âtechniciansâ replaceâ the damaged component⤠only, but if either part is old âand heat-damaged, replacing both can prevent â˘repeat failures.
How muchâ does a replacement 316580611 ignitor harness typically cost and is⣠it covered under warranty?
Retail⤠pricesâ for an OEM replacement ignitor harness typically range from a âmodest⣠parts fee to⢠around several tens of dollars, depending âon supplier âand whether it’s OEM or aftermarket. Warranty⣠coverage depends on theâ appliance’s warranty âŁperiod and the cause of failure; check your appliance âwarranty documentation or⤠contact Frigidaire/customer service. âŁIf a repair was recently performed⤠by an authorized service provider, âŁparts and labor may carry âŁa âŁshort service warranty.
Wrapping Up
the 316580611 Frigidaire ignitor harness serves as a criticalâ electricalâ connection between âthe oven or range ignitor and the appliance’s wiring system, enabling reliable transfer âof electrical current ânecessary for consistent ignition. As a small but essentialâ component, the harness helps ensure proper ignition timing, supports efficient appliance operationand contributes to overall safety by⤠maintaining âsecure, âŁcorrosion-resistant connections within the ignition circuit.
Accurate diagnosis isâ vital whenever â¤ignition problems occur, âsince symptoms⢠such as intermittent âlighting or failure â˘to âigniteâ can result fromâ a variety of â˘causes including the ignitor, â˘control boardor wiring harness itself. â¤Assessing the condition of⤠the 316580611 harness-through visual inspectionâ andâ appropriate electrical testing by a qualified technician-helps âdetermine whether repair or replacement is warranted. â˘When replacement is necessary,installing the correct,compatible harness⤠restores reliable performance,reduces âŁthe risk of recurring faults,and helps⣠maintain â˘the âappliance’s safe operation.
Maintaining attention âto proper diagnosis and using the correct replacement parts preserves appliance longevity and user âsafetyâ whileâ minimizing downtime. For best results, homeowners and service professionals should follow manufacturer guidance âand safety⤠practices to ensure âthe 316580611 ignitor harnessâ performs as intended within the Frigidaire ignition system.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
