316112005 Frigidaire āOvenā Range Anti Tip Bracket Kit is a mechanical safety assembly designed to secure a freestanding or slide-in electric or gas range to the floor or wall and ā¤prevent the appliance from tipping forward. The kit typicallyā¤ consists of a metal bracket, mounting hardwareand fasteners sized to interface with the range’s rear chassis and the installation surface; it is a structural componentā rather than āan electrical or electronic part.
Inside the appliance system the anti-tip bracketā provides a fixed attachment āpoint that ā¤resists momentsā£ generated when the ovenā¢ door is opened orā when concentrated weight āis placed on the ā£open door.It directly interacts with the range cabinetā (rear leg or āchassis),ā¤ the floor or wall substrateand the leveling system; correct installation requires coordinationā with ā£the range’s adjustable feet so the bracket engages ā¢at the designedā¢ height.ā£ properly installed, the bracket controls load paths and prevents forward rotation of the appliance under asymmetric loads, which is significant for user safety and āfor maintaining alignment with surrounding cabinetry and venting interfaces.
In the following article ā¢readers will find a technical overview of the bracket’s function, typical mounting ā¢locations, ā¤and model compatibility notes; common ā¢failure modes and symptoms to watch for (loosened or missing fasteners, excessive forward movement ā¤when the door is openedor improper engagement due to incorrect leveling); step-by-step troubleshooting ā¢and inspection checks; āand practical replacement ā¤considerations such as selecting correct fasteners for ā¤the substrate, verifying engagement height, torque recommendationsand installation safety practices.The intent is to provide technicians, engineersand appliance owners with the information needed to assess, installand verify an effective anti-tip installation in accordance with manufacturer instructions and applicable codes.
Table of Contents
- Functionā and Safety Role of the ā£AntiāTip ā£Bracket in Oven Range Stabilityā¢ and load Transfer
- How the 316112005 Frigidaire Oven Range Anti Tip Bracket Kit Integrates with the Range Chassis and Operates During Use
- Common Failure Symptoms, Mechanical Wear Modesand Visual Inspection Criteria for AntiāTip Bracket Assemblies
- Replacement Considerations, Installation Proceduresand Torque/Anchoring Specifications for AntiāTip Bracket Kits
- Q&A
- In retrospect
Function and Safety Role of the ā¤AntiāTipā Bracket inā Oven range Stability and Load Transfer
The 316112005 Frigidaireā£ Oven Range Anti Tip Bracket Kit is a mechanical restraint that secures the rear of the range to the structure so overturning loads are transferred away from the appliance chassis into the building framing. When an external moment is āapplied – forā¤ example,heavy cookware on an open door or a userā leaning on the oven door – the bracket ā£engages the range’s rear foot or frame and converts the overturning moment into shear and bending loads in the fastener and the wall stud. Proper engagementā requires the bracket to be positioned so the range pivots against it before the front feet lift;ā this ensures the intended load path directs forces ā£into a structural anchor ratherā¢ than into drywall or the appliance body alone. Verify compatibility withā the appliance by checking theā model’s āmounting provisions and follow the manufacturer’s guidance on anchorā type and orientation ā¤during installation.
From a practicalā£ and safety standpoint, the antiātip bracket is a small componentā with ā£a critical role: it does not reinforce the range for lateral seismic forces or substitute for correct leveling, but itā prevents sudden overturning from typical operational loads. Installers should use fasteners that achieveā embedment intoā framing (for example, lag screws into aā£ stud) and avoid relying on drywall anchors alone; misapplication is the moastā£ common cause of reduced āperformance. After installation, a simple functional check-pulling forward on theā range toā confirm the rear edge bears on the bracket-verifies engagement. For older or modified installations,ā confirm whether a wall- or floor-mounted bracket is requiredand inspect for corrosion, loose fastenersor deformation that would indicate replacement of the kit or refastening āto meet the original design intent.
- Primary ābehavior: arrests forward rotation by transferring momentā to building framing
- Anchorageā£ requirement: fastener embedment into stud or equivalent structural member
- Typical failure modes: improper fastener type, poor alignmentor corroded hardware
- Verification: physical engagement test and periodic inspection
| Item | Description |
|---|---|
| Primary function | Transfer overturning loads from rangeā rear to building framing |
| Typical install anchor | Lag screw āinto wall stud or equivalent structural member |
| Common failure mode | Attachment to drywall ā£only, misalignmentor loose/corroded fasteners |
| Verification test | Pull-forward test to confirm rear edgeā¢ contacts bracket and resists ātipping |
How the 316112005 Frigidaire Oven Range Antiā¤ Tip Bracket Kit Integrates with the Range ā¢Chassis and Operates During Use
The 316112005 Frigidaireā Oven Range Anti Tip Bracket Kit is a small but structurally significant component that mechanically marries the range chassis āto the building structure. Theā bracket fastens to the rear chassisā¤ flange or the range’s rear leveling leg andā to a floor or wallā structural member, creating a direct load pathā¤ for overturning moments. In normal operationā¤ the bracket sits passively under theā rear of the range; when a tipping event is initiated ā¢(such as, an open door loaded off-center), the bracket intercepts rotation and transfers compressive and ā£shear loads into the anchor fastener and the building āsubstrate instead of into the appliance hinge or cabinet sheetmetal.
- Mounting: attaches to rear chassis flange or leveling leg and to floor/joist or masonry.
- Loadā¤ path: converts āoverturning moment into shear/compression through fastener and substrate.
- adjustability: slotted geometry ā£accommodates ātypical range height/legā¢ variations.
- Materials:ā formed āsteel with corrosion-resistantā£ finish to preserve strength at the contact āinterface.
- Included hardware: lag screw or anchor sized for common installation substrates.
During everyday use the bracket remains ā£unloaded; under a tip event it engagesā¤ quickly as the chassis rear bears against the bracket lip, producing a predictable ā¢reaction that limits rotation to a few ādegrees and prevents progressive overturning so long as the fastener and substrate are adequate. Practical examples include a heavy pot āplaced on an open door or a child ā¤climbing on the door: in those cases the bracket’s role is to āstop the center āof gravity shift from exceeding the base footprint. Compatibility depends onā¢ the chassis geometry – the bracket is designed for Frigidaire rangesā¤ with a rear anti-tip tab or accessible ā¤leg – āand installers must secure the kit to a structural member. Secure anchoring toā a joist or proper concrete anchor is required; improper fastening, āmissing hardwareor ā¤excessive clearance at the interface will reduce or eliminateā the bracket’s ā£effectiveness.
| Item | Description |
|---|---|
| Primary function | Resist overturningā¢ moments by anchoring rear chassis to building structure |
| Typical attachment | Rear chassis flange or leveling leg to floor joist or masonry anchor |
| Failure modes to inspect | Loose fastener,substrate pull-out,excessiveā bracket deformation,or incorrect alignment |
Common Failure Symptoms,Mechanical Wear Modes,and Visual Inspection Criteria for AntiāTip Bracket Assemblies
The 316112005 Frigidaire Oven Range Anti Tip Bracket Kit is a stamped-steel bracket and hardware set ā£that provides a mechanical stop to prevent a freestanding range from rotating forwardā when the door is opened or a load is applied to the cooktop. The bracket captures the range rear frame or leveling leg and transfers bending and shear loads into the structural anchor (floor or wall). Proper function depends on correct ā¤orientation and fastening: the bracket must seat fully against the range frame and be secured to an appropriate substrate with the supplied or equivalent fasteners; compatibility varies by Frigidaire model and installation type, so verify fitment and mounting details against the range’s service documentation before installation. In operation the assembly is ā¤passive-its performance is persistent by the bracket geometry,ā integrity of ā¤welds or bendsand theā strength of the fastener-to-substrate connection rather thanā by moving parts.
- range shifts or rocks forward when the oven door is opened (indicates loose or failed anchoring).
- Visible bending, hooked ādeformationorā¤ fractured ā¢material at the bracket stopā£ point (mechanical yielding or overload).
- Cracked welds or separations at formed bends ā(fatigue or impact damage).
- Elongated or stripped mounting holes,ā¢ loose or missing fasteners (fastener failureā¤ or over-torque ā¢during installation).
- Severe ācorrosion or pitting that reduces cross-section or causes fastener threads to ālose engagement.
- Anchor or substrate āpull-out, āwhere the bracket remains intact but the floor/wall anchors have failed.
| Item | Description |
|---|---|
| Visual deformation | Any āpermanent bend, hooked distortionor gap between bracket and frame-replace bracket if deformation prevents full engagement. |
| Fasteners | Missing, ālooseor stripped screws/anchors-reinstall with correct hardware and verify engagement into structural material. |
| Corrosion | surface rust can be cleaned; replace bracket if pitting compromises metal thicknessā or fastener threads. |
| Anchor substrate | Concrete, woodor stud backing must hold torque; replace anchors orā reinforce ā¢substrate if āpull-out is observed. |
| Engagement gap | Bracket must capture the range frame without āexcessive ā£gap; excessive clearance indicates deformation or incorrect installation. |
Inspection should combine a tactileā£ testā and visualā¢ assessment: apply forward pressure at the countertop or door edge to detect movement, verify that the bracket sits flush āagainstā the rear frame, inspect welds and bends for hairline cracksand confirmā¢ thread engagement of all āfasteners. If inspection reveals fractures, significant bending, elongated holes, missing hardware, ā¤or anchor pull-through, replace the bracket and associated anchors rather than attempting repair; minor surface corrosion and paint loss can be cleaned and recoated but mustā¢ not mask structural defects. For reinstallation use manufacturer-specifiedā¤ hardware or equivalent rated fasteners and follow the service manual for recommended orientation and anchoring practiceā£ to restore designed load transfer.
Replacement Considerations, Installation Proceduresand Torque/Anchoring Specifications for AntiāTip Bracket Kits
The 316112005 Frigidaire Oven ā£Range Anti Tipā£ Bracket Kit is a retrofit component designed to arrest forward rotation of a freestanding rangeā by capturing the appliance’s rearā£ leveling leg or chassis flange. When selecting a replacement, confirm the range rear foot geometry and the mounting substrate: the bracket can be installed into cabinetry, a hardwood floor or concrete, but the required fastener type andā¤ anchor depth differ.replacement considerations ā¢include ensuring the bracket aligns withā£ the range’s rear leg travel, verifying there is sufficient clearance behind the rangeā£ for full engagementand confirming thatā any existing blocking or cabinet structure can accept the specified fastener without causing distortion of the bracket or the appliance frame.
- Preāinstallation āchecks: measure rear leg location, inspect floor/cabinet substrateand verify bracket orientation.
- Fastener ā¤choice: select wood screws or lag bolts āfor solid ātimber/blockingand mechanical or epoxy anchors for concrete.
- Tightening procedure: graduallyā¤ tighten to specified torque values-snug first, final torque with a calibrated wrench.
- Functional test: level āthe range,slideā into position,and push forward ā£to verify the antiātip bracket fully captures the rear foot.
| Item | Description |
|---|---|
| Wood/block mounting | #12 wood screws or 1/4″-5/16″ lag; final torque ~60-80 inālbā¤ (5-7 ftālb) |
| Concrete/ masonry | 3/8″ wedge or sleeve anchor; installationā torque ~30-50ā ftālb depending on anchorā¤ type |
| Sheet ā¢metal/cabinet faces | Provide internal blocking; do not rely on thin panel alone |
During installation, tighten fastenersā in a controlled sequence: snug each fastener so theā¤ bracket seats flat, then apply the specified final torque to prevent loosening under load. Useā¤ a calibrated torque wrench for the final pass and avoid driving screws by feel; do not overtighten sheet metal surfaces, as that can deform the bracket or stripā threads. After installation, restore appliance ā£position and verify engagement by pulling the range āforward against the ācabinet; repeat torque verification after the first week of use or after any heavy movement. For older āor nonāstandard ranges, consider fabricating aā small adapter plate orā adding blocking so theā¤ bracket captures a solid surface rather āthan thin trim.
Q&A
What is the 316112005 Frigidaire Oven Range anti Tip Bracket Kit and what partsā comeā in the kit?
The ā£316112005 isā an OEM ā¤antiātip bracket kit made for Frigidaireā¤ ranges. It typically includes a stamped steel antiātip bracket and the fastenersā£ needed for ā£common installations (wood screws/lag screw and masonry ā£anchor orā£ toggleā¢ anchor). Kits vary slightly byā vendor, so check the partsā£ list that comes with the kit to confirm exactly which anchors are included.
Why do āI need to install an antiātip bracketā on my ārange?
The antiātip bracket prevents the range from tipping forward when āweight is applied āto an open oven door or when someone leans on the cooktop – a major childāsafety and injury hazard. Manufacturers require an antiātip device be installed and many ā¢building codes also require it. Installation is a safety requirement, not optional.
Which Frigidaire models is part 316112005 compatible with?
316112005 is designed for many Frigidaire freestanding and slideāin ranges,but it is not universally compatible with every model. Always check your specific appliance model number against the Frigidaire parts list or the installation āmanual.ā If in doubt,contact Frigidaire/Amana/your dealer with your ā£appliance model number to confirm fit.
How do I install the antiātip bracket? What tools and steps are required?
Basic steps: 1) Disconnect power (and gas, if applicable)ā and pull the range forward. 2) identify the recommended mounting location (usually on the floor at the rear or on a rear wall cleat) following the ā¤range installation instructions. 3) Use a stud finder and mark mounting points; for wood subfloor or floorā joist use the lag screw, ā¤for concrete or tile use the masonry anchor supplied.4) ā£Fasten the bracket securely so it cannot pull out. 5) Slide the ā¤range back until āthe rear leveling leg or rearā¢ foot engagesā¤ in the ā¢bracket. Tools typically needed: drill/driver, appropriate drill bits for wood/masonry, socket orā wrench for lag screw, stud finder, tape measure and ālevel. āAlways follow the manufacturer’s printed instructions included with the kit.
How can I verifyā the antiātip bracket is installed and engaged ācorrectly?
Visually confirm the bracket is āfastened solidly ā¤to āthe floor/wall and that the rear leveling leg or rear foot of the range sits fully into the bracket when the range is pushed back into place. Carefully attempt a light forward tilt of the top ā¢front of the range (oneāhand pull) – ā¤the rangeā£ should not tip forward.ā Doā¢ not perform aggressive ā¢or ā£fullābody tipping tests. If unsure,pull the range out and reācheck fastenerā£ tightness and anchorage.
Can I use ā¢this kit ā¤on tile or concrete floorsand what anchors should I use?
Yes – you can mount the bracket āto tile or concrete, but you must use appropriate masonry anchors (concrete ā¢anchors, sleeve anchorsor toggle anchors) rated for the loads. The kit often supplies a basic masonry anchor;ā ifā¤ your substrate is ā¤different āor the provided anchor is notā¤ suitable, use an appropriately sized masonry fastenerā¢ and drill the correct diameterā pilot hole. Follow the anchor manufacturer’s rating and installation instructions.
Do I have to remove or adjust the bracket if I move the range to āanotherā location?
If you move the range, you must either remove andā¤ reinstall the bracket in āthe new location or install a ā¢new bracket suited to the newā floor/wall conditions. Before ā¢moving the range, disconnect power and gas, ā¤then carefully unhookā¢ or removeā¢ the range from the bracket (support ā¤the appliance while doing this). Reinstall the antiātip device āatā the new siteand never operate theā¢ range without an approved antiātip device properly installed.
What if the bracket or hardware gets damagedā – can I replaceā only ā¢the broken parts?
Yes. Damaged brackets or hardwareā¢ should be replaced immediatly. you can ā¤order replacement 316112005 OEM brackets and often the corresponding fasteners separately. If you cannot obtain the OEM parts, replace with an antiātip deviceā rated forā£ ranges that matches the āoriginal mountingā£ configuration and load ācapacity. Do not attempt to operate the appliance with a compromised antiātip device.
In Retrospect
The 316112005 Frigidaire Ovenā Range Antiā¤ Tip Bracket Kit serves ā¢a straightforward but critical safety function: it secures ā¤the range to the floorā or wall to prevent forward tipping during normal use or when the oven ādoor is opened. As aā£ simple mechanical restraint, the bracket playsā£ an critically important role in reducing the ā£risk ofā scalds,ā£ crush injuries and property damage byā maintaining appliance stability and ensuring the range remains ā£positioned as intended.
Proper diagnosis and timely replacementā¢ of the antiātip ābracket are essential to āmaintain that āsafety āfunction. Regular inspection for wear,damage,corrosion or loosened fasteners-and verification that ā¢the range does not rock ā£or shift-will identify when service is needed. When replacement is required, using the correct kit (such as the 316112005 designed for compatible Frigidaire models) and following manufacturerā installation instructions or engaging aā¤ qualified technician helps ensure āthe bracket performs as intended.
maintaining ā£a secure antiātip installation is a lowācost precaution with meaningful safety benefits. Routineā¢ checks, adherence to installation guidelines and prompt replacement when defects are found help preserve appliance safety and give users reasonable assurance that the range willā remain stable during everyday operation.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
