137006900 âFrigidaire Washer â˘Strike is âŁa â¤replacement strike piece used in âFrigidaire washing machines; it is indeedâ the mechanicalâ mating surface that âŁthe door or â¤lid latch engages when âŁthe appliance is closed. as a strike component, it is typically a⢠small,⢠fixed â˘bracket or⢠plate made ofâ metal or reinforced plastic that provides⣠a reliable contact point⢠for the latch or interlock mechanism to capture and hold the âŁdoor in âthe closed âŁposition.
Inside the appliance, the strike functions asâ part of the â˘door/lid retention and safety interlock system. It interacts directly with âthe latch or lock actuator and âindirectly with electrical components such asâ the door-lock switch, lid switchor control boardâ that â˘monitor closed-door status.Proper⢠engagement of the strike is required for the controlâ electronics to permitâ fill, spinor motor operation;â misalignment, damageor wear on the strike can prevent the latch from seating and thereby inhibit â˘normal cycle initiation âfor safety reasons.
In this article readers will find a technical overview of the âstrike’sâ function and typical mounting locations, guidance on compatibility and OEM identification, common failure symptoms to recognize (for example, door not latching, start inhibitor intermittent cycle starts), diagnostic approaches toâ isolateâ strike versus lock-electronics faultsand practical replacement considerations such as dimensional checks, alignment, fastener conditionand inspecting associated latch/lock components. The goal âŁis to equip technicians,â engineersand experienced appliance owners with the context needed to assessâ whether the 137006900⤠strike â˘is implicated in a serviceâ issue and⤠what factors⣠matter whenâ replacing âit.
Table of Contents
- Function and Role of the Door Strike in Frigidaire Washer Locking and Safety Systems
- How the 137006900 âFrigidaire âWasher Strike Operates Within the Door Lock Assembly â¤and Controlâ Circuitry
- Common Failure Symptoms and Diagnostic Procedures for a Defective⢠Washer Strike
- Compatibility, â˘Replacement âConsiderationsand Step-by-Step Installation Requirements for⢠the 137006900 Strike
- Q&A
- In Summary
Function and Role of the Door Strike in Frigidaire Washerâ Locking andâ Safety systems
The 137006900 Frigidaire Washer Strike â is the mechanical keep that receives the door latch and provides the precise engagement surface⤠requiredâ for the washer’s door lock system to register a closed and locked condition. In this role the â˘strike aligns the door with the interlock assembly,â transmits the retention force during highâspeed spinand ensures âthe actuator or microswitch within the lock assembly is actuated reliably. When the strike is worn, crackedor misaligned the lock may notâ engage, the control will inhibit âmotor start or display a âdoorâ errorand the⤠door may open under torque; these behaviors reflect a mechanical or⢠positional fault rather than an electrical control failure in many diagnostic scenarios.
Technically, the strike â˘functions as part of a mechanical-electrical interface: itsâ geometry and mounting determine switch actuationâ timing and the â˘load path â¤that prevents door deflection. Service technicians typically verify correct striker height, fastener torqueand matingâ surface⤠condition before⢠replacing the â˘lock module – a loose or deformed strike can simulate lock failure. Common practical checks include visual â˘inspection for plastic fatigue, measuring alignment⣠relative to the âŁlatchand confirming that correction of striker position restores normal switch continuity and cycle operation.
- Common symptoms: door will not latch, washer will ânot start, intermittent door-open errorsor door release during âŁspin.
- Typical failure â˘modes: plastic breakage, surface wear altering actuation point,⢠or mounting screw loosening causing misalignment.
- Service actions: inspect strike geometry, adjust⣠mounting position, replace with matched part number when damaged.
| item | Description |
|---|---|
| Part | 137006900 Frigidaire Washer Strike – replacement striker/keep for âcompatible⢠Frigidaire front-load doors |
| Primary function | Provide retention andâ accurate actuation interface forâ door lock âmicroswitch or interlock |
| Common symptoms | Door⢠won’t latch/start, â¤door error codes, intermittent lock âengagement |
How the â137006900 Frigidaire Washer Strike âOperates Within the⤠Door Lock Assembly⤠and Control Circuitry
137006900 Frigidaire Washerâ strike is the mechanical â˘interface that⣠the door uses to âŁengage the door lock assembly and provide the control âcircuitry with a positive closed-door signal. When the door closes, the strike’s geometry âaligns with the lock⤠housing so that a plunger, latch pawlor âmicroswitch inside âthe lock assembly is depressed or captured. That â˘action either completes an electrical circuit or allows an internal actuator to move to the locked position; the control board senses⤠that âcircuit closure or âinterlock state and proceeds with⤠the selected programme. The strike itself is passive-its correct function âŁdepends onâ precise fit, correct engagement depthand intact mounting tabs so thatâ the electromechanical components in⣠the âŁlock assembly can respond reliably.
Technicians should⤠treat âthe strike as both a mechanical âalignment⤠piece and⣠a âcompatibility itemâ when replacing failed⢠components. Common symptoms of âstrike failure include incomplete switch actuation, intermittent door-ajar errorsor physical movement of the door that prevents âthe lock from capturing the strike; these problems are âŁdiagnosed by visual inspection,⤠verifying that the strike⢠engages the lock plungerâ cleanlyand performing continuity checks on the lock⢠switches with â˘the door closed. Replacement requires matching the mounting pattern and actuator interface-using the correct part number reduces the risk of misalignment-but basic troubleshooting steps such âas checkingâ for cracked plastic, deformed engagement surfacesor loose mounting âscrews will often identify issues before ordering a new strike.
- Symptoms: washer â¤won’t⢠start, â˘door-ajar âor lock â¤error codes, loose or broken strike tabs.
- Rapid checks: visual alignment, manual actuation of âthe lock while monitoring switch continuity, verify secure mounting.
- Replacement consideration: ensure matching geometry and mountingâ points to⣠avoid improper switch actuation.
| Item | Description |
|---|---|
| Mechanical role | Provides the physical interface that captures or depresses the lock’s internal actuator when the door closes. |
| Electrical interface | Enables microswitch or interlock state that the control board reads as âdoor closed/locked.â |
| Troubleshooting test | Inspect for damage/alignment, then âverify switch continuity⤠or control signal when the strike is engaged. |
Common Failure Symptoms and Diagnostic Procedures for⢠a Defective Washer Strike
The 137006900 Frigidaire⣠Washer Strike is the fixed⣠receiver that the door latch or lock assembly engages toâ secure the washer door during a âcycle. Functionally it provides a precise mechanical interface: correct geometry andâ mounting ensure the latch âŁplunger or hook fully captures the strike and allows the interlock or microswitchâ to register a closed door.Compatibility depends on the strike’s tab spacing, thicknessand screw hole pattern; a visually⢠similar part can still fail to â¤engage if the mounting â˘flange or offset differs by a few millimeters. Typical failure modes are plastic deformation of the strike face, fractured mounting tabsor wear that increases clearance so â¤the latch does not reach the âinterlock travel, causing door-fault conditions⤠even though the lock assembly itself might potentially be âfunctional.
- Door will â˘not lock⢠orâ “door” error displayed despite functional lock âactuator
- Washer stops mid-cycle with door unlocked or latch onlyâ partially engaged
- Visibleâ cracks, worn latch contact surface,⢠or⣠broken mounting tabs
- Intermittent operation reproduced by flexing the strikeâ or jiggling the door
| Item | Description |
|---|---|
| Visual inspection | Check⣠for cracked⤠plastic, worn catch surfaceand proper alignment with âŁlatch â˘hook |
| Electrical/continuity test | With power removed,⢠verify interlock continuity⢠and observe changes while actuating the latch |
| Mechanical engagement âtest | Manually⤠close door and confirm full⢠capture ofâ latch; measure⢠gap â˘and mounting offsets |
Diagnostic procedure starts with a visual inspection and mechanical âengagement test: disconnect⤠power, â˘open âŁthe âaccess panel, âŁand observe the strike whileâ the door is âclosed to⣠confirm fullâ travel and clean â¤contact without â˘binding.If⢠the⤠strike appears intact but the system reports a door-fault, use a âmultimeter to check continuity across the interlock or⤠latch switch while manually actuating theâ latch; a drop in continuity or intermittent signal while flexing the strike indicates a fractured contact or mounting fatigue. For repair, replace the strike with a part that matches the original â¤mounting dimensions and material; if âsymptoms persist after replacement, confirm the latch actuator and wiring harness are within specifications and that âthe strike alignment relative to the latch hook meets manufacturer tolerances.
compatibility, Replacement considerationsand Step-by-Step Installation Requirements for the 137006900⢠Strike
The 137006900 Frigidaire Washer Strike is a mechanical latching component that engages the door/lid âinterlock⤠and âprovides the final physical retention⤠required âfor⤠the washer to enter a spin or wash cycle. It converts⤠the actuator movement of the âlatch assembly into⤠linear plunger motion that holds â¤the door closed andâ permits the interlock switch to register a closed condition. Technicians â˘see failures as excessive plunger play, â¤broken plastic ears, worn cam surfacesor misalignment that⣠prevents the⣠interlock micro switch from closing; these symptoms âtypically produce no-start conditions,⤠door-open errorsor intermittent locking. Verify compatibility by comparing the part number, mounting-hole spacing,⤠plunger length⤠and traveland actuator geometry to the original strikeâ before replacement, because variations in plunger throw or mounting geometry can prevent proper engagement even if theâ part superficially looks the same.
- Pre-replacement⤠checks: confirm âŁOEM part number⤠or âmeasure mounting hole spacing and plunger travel; inspect surrounding brackets and grommets for wear.
- Tools and safety: âdisconnect â¤mains power, have a hand screwdriver set, small socket or nut driverand a multimeter âfor continuity checks.
- Installation sequence: remove trim/panel to access strike, remove mounting fasteners while supporting the â˘striker, â¤fit new strike ensuring⤠plunger âŁaligns with latch hook,â secure fasteners without over-torquingand perform electrical and functional tests.
| Item | Description |
|---|---|
| Typical reference | Screw type: #8 self-tapping or M4 sheet-metal fasteners; torque: snug to⣠~12-25â in¡lb (hand-tighten until seated, avoid stripping); âplunger travel: typically â6-12 mm – verify againstâ OEM; ensure mounting-hole spacing and â¤actuator orientation match original. |
Installation requires aligning âŁthe strike so⢠the plunger â˘fully inserts intoâ the lid latch pocket âwithout binding and so the interlock switch is actuated at the correct point âof travel. After mechanical installation, check switch continuity withâ a multimeter while manually depressing â¤the plunger to confirm the âcontrol sees a closed⢠circuit; then run a short diagnostic or cycle to confirm theâ washer transitions to the âlocked state and clears any âŁdoor-lock error codes. If the replacement strike does not permit âfull engagement or requires abnormalâ force to latch, remove it and compare dimensions – a shim, different screw length,â or selecting the correct OEM strike isâ preferable to âŁforcing alignment, whichâ can stress plastics and create premature failures.
Q&A
What is the 137006900 Frigidaire washer⤠strike?
The 137006900 is an OEM replacement â”strike” (latch keeper) âused on certain Frigidaire washers. It is indeed the stationary part mounted in the washer cabinet that the lid/door latch engages with to hold the lid/door closed while âthe machine runs. The strike itself is a mechanical piece (usually⤠plastic or metal) and does not containâ electrical components.
What symptoms indicate the strike is bad or needsâ replacement?
Common symptoms are the lid/door not staying fully closed, the washer refusing⣠to â˘start or immediately tripping theâ door-lock error, intermittent locking where the âlatch does not âŁengage reliablyor visible⤠damage such as cracks, broken tabsor âmissing mounting points on the strike. You may also hear the lock actuator click without the lid actually locking-this can indicateâ a damaged or misaligned strike.
How do I check whether the âstrike âor the lid-lock assembly is the problem?
Visually inspectâ the strike for cracks, wear âŁor âdeformation and check that it lines up cleanly with the latch â¤on âthe lid/door. manually close the lid and observe whetherâ the⢠latch fully engages⤠the strike. If the strike looks intact but the lock actuator does not click or the control reports a door-lock error, â¤the lid-lock (electrical actuator/switch)â may be faulty. If the âactuatorâ clicks but locking still âŁfails, the strike is highly likely the problem.
Is the 137006900 âŁstrike difficult to replace,⢠and what tools are needed?
Replacement is typicallyâ straightforward â˘for someone comfortable âwith basic appliance repair.common tools: screwdriver or nutâ driver setand⢠possibly a putty knife or trim tool to release clips. You must unplug the washer (or turn off power) before starting. Access usually ârequires opening the top panel or removing a small âŁtrim piece to reach the strike screws.Remove the old strike, âfit the new oneand fasten securely, then test operation.
Will replacing âthe strike always fix a door-lock problem?
No. If the âissue is withâ the lid-lock actuator,wiring,door-lock switch,or the control board,replacing the strikeâ alone will not âŁfix it.⣠Replacing the strike fixes â˘problems caused by âa âphysically broken or misaligned⤠keeper. If the strike âŁreplacement does not restoreâ reliable locking, you shouldâ test the lid-lock assembly and wiring for faults or error codes.
Are âthere multiple versions of the â¤strike and how do I make sure 137006900 fitsâ my washer?
Yes-strikes vary by model and year. Always verify compatibility by⤠matching your washer’s model number (usually on a sticker behind the âdoor or on the cabinet frame) against the part listing. Check the parts diagram for your exact model or consult an âauthorized Frigidaire parts âdealer to confirm that⣠137006900 isâ theâ correct replacement for your machine.
Where⣠can I buy the 137006900 part⢠and is aftermarket acceptable?
You can buy⢠the 137006900 from authorized â¤Frigidaire parts âŁdistributors, major appliance parts retailersor reputable online âŁsellers. Aftermarket âstrikes are available and âoften less expensive, â¤but quality â˘can vary.â Prefer OEM âwhen possible for fit and durabilityor buy⢠from a reputable aftermarket brandâ and verify return â¤policy in case fitment⢠issues â˘arise.
Any tips for installation and final testing after replacing the strike?
Before reassembly, check alignment⣠by manually closing â¤the lid several times to ensure smooth engagement. Tighten mounting screws snugly but avoid over-tightening plastic bosses. Reconnect power and run a short cycle or a diagnostic/door âtestâ if your⣠washer has one â¤to confirm⢠reliable locking. â˘Ifâ youâ see any door-lock error codes after⢠installation, âŁre-check alignment âand⣠inspect the lid-lock actuator and wiring âharness for damage.
In â¤Summary
The 137006900 Frigidaire washer strike is a small but essential component that helps secure âthe washerâ door and engage the door-latching mechanism, contributing âŁto safe operation, proper cycle initiation, âand reliable sealing during use. Because it interfaces directly with the door latch and safety interlock system, wear, damageor misalignment of the strike can lead to door-related errors, interrupted cycles, âorâ reduced performance, making its role important â¤to both functionality and user safety.
Accurate diagnosis is key when troubleshooting door or cycle-start issues: careful âinspection of the strike and surrounding⣠hardware, evaluation of⢠alignment and wearand assessment of related â˘components will indicate whether repair or replacement is⣠appropriate. When⢠replacement âis necessary, using âŁthe âcorrectâ 137006900 part â˘or an equivalent OEM-specified âcomponentâ and following manufacturer âguidance-or engaging a qualified service⣠technician-helps ensure compatibility, restoreâ proper operationand maintain safety and warranty considerations.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
