The 137221600 Frigidaire â¤Washer Drain â˘Pump is an electric drain-pump assembly used in âŁfront- adn top-load washing machines to evacuate wash â˘and rinse water from the tub. It is âŁindeed a compact electromechanical component â˘typically comprising a small motor, an impeller or rotor, a molded housing with inlet and outlet portsand electrical terminals; it mounts to the washer chassis or tub and connects to the drain hose and control system.
Within the appliance,â the⤠drain pump’s primary role is to move water from the wash tub to the household drain during drain and spin cycles.It⤠interfaces directly⣠with âthe tub⣠outlet and drain hoseand indirectly with the control board (which supplies power âand timing), the water-level sensing system (which triggers drain events)and mechanical seals âor filter assemblies that prevent debris â˘from reaching the â˘impeller. Proper operation depends on correct electrical supply, unobstructed fluid flowand intact seals andâ mounting hardware; its hydraulic âŁcapacity and orientation determine âdrain time âand reliability under varying load⢠conditions.
In this article readers will find a⢠technical overview âof the pump’s function and typical construction,guidance on compatibility and how to confirm correct part selection for specific Frigidaire models,common failure â¤symptoms (for example noâ drain,noisy operation,intermittent operation,leaks,or motor hum),and systematic troubleshooting steps including⣠electrical checks,inspection for blockages,and verification of control signals. It will also cover practical replacement considerations-mechanical fit, electrical connector type, sealing/gasket requirementsand post-installation testing-along with safety precautions to follow when working on the⢠washer.
Table⣠of â˘Contents
- Function and Role âof the Drain Pump in⢠Frigidaireâ Washer Water-Managementâ systems
- How âthe 137221600 Frigidaire Washer Drain Pump Works Inside the Appliance:⢠mechanical Operation, Electrical drive and Control Interfaces
- Common Failure Symptoms, Error Codes and Diagnostic Indicators for the Drain Pump âŁAssembly
- Replacement Considerations and Installation Procedure: Tools, âfastening, Seal Integrity and Verification
- Q&A
- Wrapping Up
Function and Role of the Drain Pump in Frigidaire Washer Water-Management âŁSystems
The 137221600 Frigidaire Washer Drain Pump is a centrifugal pump assembly that evacuates wash and rinse water from the tub by converting⣠electrical drive into â¤rotational motion at an â¤impeller. It mounts to the washer base and interfaces mechanically and electrically with âthe chassis, â˘drain âhoseand control board; âreplacementâ requires matching the pump’s connector orientation, mounting holesand outlet position to ensure proper clearance and hose alignment. In operation the pump receives a drain command from â˘the machine controller, draws⤠current through its motor windingsand forces water out âŁthrough the drain hose while âinternal check-valves⤠or lip sealsâ prevent backflow and tub flooding when idle.
Typical pump behavior includes a continuous lowâlevel mechanical noise during operation â¤and steady flow through the â¤drain hose; commonâ failure modes are electricalâ winding faults, seized or clogged impeller, failed shaftâ seal causing leaksand intermittent connector or controller faults. Technicians commonly isolate failure by â¤checking for audible motor operation during a drain cycle, confirming continuity â˘at the pump âŁterminals, removing debris from the inlet and impeller areaand verifying the control board supplies expected drive voltage. Replacement âwith the correct OEM pump avoids misalignment⣠and electrical mismatches; if replacement does not restore draining, systematically check the drain hose routing, pump inlet filter/trapand control outputs.
- No⢠drain and no audible motor: verify harness continuity and control-board outputâ to theâ pump.
- Motor⣠hums but no water: inspect impeller for debrisâ or mechanical seizure.
- Visible leak at pump âŁhousing: suspect âshaft seal failure or cracked housing-replace pump.
- Intermittent operation: check connectors, wiring for corrosion or⣠intermittent shorts and confirm âcontroller timing.
| Item | Description |
|---|---|
| OEM Part | 137221600 Frigidaire Washer Drain Pump – pump assembly with specifiedâ mounting and connector configuration |
| function | Removes waterâ from tub during âdrain cycles and âprevents backflow when idle |
| Typical motor type | Small AC/DC centrifugal⤠motor with molded impeller (varies by model family) |
| Common symptoms | No drain, humming without flow, visible leaksor intermittent â¤operation |
| Service checks | Audible operation during drainâ command, continuity at terminals, impeller and inlet inspection, verify control-board drive |
How the 137221600 Frigidaire Washer Drain Pumpâ Works Inside the Appliance: mechanical Operation, Electrical Drive and Control Interfaces
The 137221600 Frigidaire Washer Drain Pump is a compact pump assembly that removes wash and rinse water â¤from the tub by converting rotational energy into flow. Mechanically,â the unit uses â˘a small electric motor â¤directly coupled to â¤a âmolded plastic impeller in a sealed⤠volute; âthe rotating impeller produces pressure that forces water out through the discharge port. mounting geometry, inlet screen position and the âsealing gasket determine how the pump integrates withâ the washer’sâ plumbingand common mechanical issues-debris on â˘the impeller, worn bearingsor a damaged seal-manifest as reduced flow, grinding noiseor leaks. âIn practice, â¤a⢠technician inspecting a âŁnon-draining machine should check the impeller for obstructions and verify thatâ the discharge hose and tub trap are clear before assuming motor failure.
Electrically, most âinstallations of this drain âŁpump use âa⢠singleâphase AC motor (typical North American line voltage 120 VAC)â that is switched on and off⣠byâ a relay or solidâstate switch on theâ washer control board; these pumps are generally openâloop devices without a tachometer, so the control strategy⣠is simple timeâ or event based.â The âcontrol board mayâ include current sensing to detect jammed conditions (elevated current) or an open circuit (no current). Compatibility when replacing theâ pump requires matching the mountingâ flange, electrical⤠connector type and voltage rating, as well as verifying hose diameter and discharge â¤orientation⤠to avoid fitment or strain issues.⣠Common diagnostic traces include: a⣠humming pump with no flow (impeller jam or failed start circuit),a noisy pump (bearing wear),intermittent⢠operationâ (poor connector or control board relay),and visible leakage (seal failure).
- Symptoms to observe: hummingâ without flow, excessive âvibration/noise, visible leaks, intermittent or no âoperationand continuous ârunning⢠after cycle end.
| Item | description |
|---|---|
| Voltage | Typically 120 VAC singleâphase âfor North American models |
| Drive | Directâdrive motor to a centrifugal impeller⣠(no gearbox) |
| Control interface | Switched by relay/triac on washer control board; âŁsimple on/off operation,⤠often with current sensing |
| Common failure modes | Impeller blockage, worn âbearings, seal leaks, electrical open/short or⢠failed relay |
Common âFailure Symptoms, Error Codes and Diagnostic Indicators for the Drain Pump Assembly
The 137221600 Frigidaire âWasher Drain Pump is the electromechanical assembly responsible for evacuating wash and rinse water from the tub⤠through the drain hose. It couples a small AC motor âto a molded impeller inside a sealed housing; operational behavior includes rapid âstart/stop during the drain cycle, free rotation of the impeller when⤠power is removedand noâ continuous â¤run outside of active drain âstages. This pump is âan OEM-design replacement used on specific âFrigidaire washer platforms-confirm chassis,⤠connector styleand drain housing fitment against the service parts âŁlist before installation to ensure mechanical and electrical âcompatibility.
Common failure signs and diagnostic indicators point to either hydraulic restriction, mechanical seizure, electrical faults âŁin the pump motoror control/wiring issues upstream. Typical troubleshooting steps are: visually inspect and clear foreign objects from the pump inlet âand lint trap; verify pump shaft turns⤠freely by hand; measure continuity â across the motor windings and ⢠measure voltage at the pump connector during a drain command (line voltage expected on âmost U.S. models). If the pump âhas continuity and correct voltage but does⣠not turn, the pump motor is defective; if there isâ voltage absence,⣠the âfault is likely in the control board, â¤relayor wiring. The list below âsummarizes the â¤most common symptoms âyou will encounter during diagnosis.
- Washer stops mid-cycle or displays a drain-related fault while water remains⤠in the tub.
- Audible humming or⤠grinding during drain (indicator of jammed impeller or bearing failure).
- Intermittent draining or very slow drain due to partial blockage in pumpâ housing orâ hose.
- Immediate open circuit on winding measurement or noâ mechanical rotation when⣠power applied (pump motor failure).
| Item | Description |
|---|---|
| Continuity | Motor windings âshould show⢠continuity; a complete âopen circuit requires pump replacement. |
| Voltage at connector | Line voltage present during drain command indicates pump should run; no voltage points to control/relay/wiring fault. |
| Mechanicalâ inspection | Check for debris in inlet, â˘damaged impeller bladesand seized shaft; these are âcommon non-electrical⤠failures. |
| Compatibility check | Verify connector type,⤠mounting bossesand hose alignment against service parts data before ordering. |
replacement Considerations and installation Procedure: tools, Fastening, Seal â¤Integrity âand Verification
The 137221600 Frigidaire Washer âDrain Pump is a sealed, impeller-driven assembly that â¤evacuates wash water from the tub and routes it out through the âdrainâ hose. When selecting a replacement, confirm the pump’s flange shape, mounting hole pattern, electrical âconnector typeand â˘drain-hose diameter to â¤ensureâ mechanical and electrical compatibility; mismatches can cause misalignment, âundue strain on hose clampsor⣠poor sealing. Inspect the pump housing and mounting grommet for cracks⣠or compression set,and replace the rubber gasket or anti-vibration mount if worn,as a compromised âŁsealâ or a warped housing will permitâ leaks or air ingestion that degrades pump performance. Typical failure modes include impeller damage from debris, motor winding⣠faultsand seal leakage-each requiring âdifferent verification steps after installation to confirm restored function and leak-tight integrity.
- Essential tools⣠and items: Phillips/flat drivers, nut drivers, slip-joint pliers or hose clamp pliers, multimeter, small pick for gasket seating, replacement grommet or clampand a drain pan.
- Critical installation/verification steps: âŁdisconnect power and drain the⢠tub, transfer any inlet/outlet fittings or grommets to the new pumporient and seat the pump so the⣠impeller shaft is unobstructed, âtighten fasteners evenly (avoidâ over-torquing), secure âhose clamps at theâ corrugation or smooth section specified, â˘then â˘run a short drain cycle while â˘checking for leaks and abnormal noise.
During assembly, ensure the pump⤠body compresses the gasket evenly and that the âelectrical connector’s locking tab is fully engaged to prevent intermittent connections; use strain relief for wiring so harness movement does⣠not⤠load the connector.⢠After securing fasteners and hose clamps, perform a functional⤠verification: a â¤dry â˘test with no water should show the motor drawing normal current and⤠the impeller free of binding, followed by a wet drain test to confirm flow rate and absence of leaks. For leak-prone installs, retighten clamps after the first test âcycle and visually recheck âthe grommet and mating face; verify no leaks before returning the⤠appliance to⤠service to prevent water damage and electrical hazards.
| Item | Description |
|---|---|
| Mounting fasteners | Sheetâmetal or machine screws matching factory pattern; tighten⢠firmly without distortion |
| Hose diameter | Commonly â16-20 mm (about 5/8″-3/4″); use correct clamp size and seating |
| Electrical connector | 2-3 pin locking plug; ensure terminals fully engaged and insulation â¤intact |
Q&A
What is the Frigidaire part 137221600 and what does it do âin my washer?
Part 137221600 is a drain pump assembly used on certain Frigidaire (and related Electrolux-designed) washing machines. Its job is to remove water from the tub during âthe drain and spin âportionsâ of the cycle by drawing water through the âtub outlet and expelling it out â¤the drain hose to your household âplumbing.
How can I tell if the drain pump (137221600) â¤is failing or needs replacement?
Common signs of a failingâ drainâ pump include: washer not draining orâ leaving water in the drum, loud grinding or rattling noises during⤠drain, humming without â˘draining (indicates a jammed impeller or seized motor), frequent error codes related to⤠draining, â¤and visible leaks from the pump â¤housing or seals. Before replacing, always check for clogs âŁin the drain hose, pump inletand anyâ coin/felt traps.
How do â¤I âtest the 137221600 drain⣠pump before replacing it?
First, disconnect âpower and remove access to the pump. Manually inspect and remove debris from âthe impeller area. Use a⤠multimeter to check the pump motor â˘for electricalâ continuity across its âŁmotor terminals (no open circuit). During a â¤drain cycle, if safe,⢠measure for line voltage at the pump connector-if voltage is present⢠but the motor does not run, the pump⤠is bad.â If there is no voltage, the problem may be the control board, timer or wiring. Do âŁnot test live circuits unless you are qualified and âtake proper âsafety âprecautions.
Can I replace the⤠Frigidaire 137221600 drain pump myself? What tools and safety steps areâ required?
Many owners â¤can replace this pump themselves if they are pleasant with basic⢠appliance â¤repair. Typical tools: screwdriver set,pliers,bucket/towels,and possibly a nut driver.Safety steps: unplug the washer, turn off the water,⤠drain any standing water into a bucket, note wire/hose locationsâ or⣠take pictures, remove the access panel, disconnect electrical connector and hoses (be prepared forâ residual water), remove mounting screws and install the new pump in reverse order. Ensure all hose clamps and gaskets are seated and power up only after reassembly. If unsure, hire a qualified technician.
How do I knowâ if the pump is compatible with my washer model?
Compatibility is âŁsteadfast by your washer model number and the âmanufacturer’s parts list.Check your washer’s model tag (usually on the door frame or back), consult theâ Frigidaire parts diagramor enter the model and part number on⢠a reputable parts website to confirm fit.Avoid guessing by part numberâ alone; several pumps â¤can look similar but have different mounting orientations, connectorsor impeller designs.
My washer pump hums but doesn’t pump water. Is the pump repairable or âŁshould I replace it?
Humming often indicates the motor is⤠receiving power but the impeller is jammed or the motor bearings are seized.â Sometimes you can free â˘debris and restore operation, âbut if the motor is worn, bearings are bador â˘the impeller isâ damaged, replacement is⢠recommended. Because pump assemblies are relatively inexpensive and critical to reliable operation, replacement is usually âthe most practical fix.
what preventative âŁmaintenance can extend the life of part 137221600?
To prolong pump life: avoid overloading the washer, remove coins and⢠large debris from pockets before âŁwashing, use a â˘mesh⣠laundry bag for â¤small items, periodically âŁinspect⣠and clean the âŁdrain filter or trap if your model has oneand run a maintenance cycle⢠with no clothes using a washer cleaner to keep hoses and passages clear. Replacingâ worn or cracked drainâ hoses and keeping the drain pathâ free of obstructions also reduces strain onâ the pump.
Where can I buy a replacement 137221600 pump âand is⤠it better to buy OEM or aftermarket?
You can buyâ the pump from Frigidaire-authorized âparts dealers, major appliance parts⢠retailersor online marketplaces. OEM (original equipment manufacturer) parts guarantee fit and specification matching; aftermarketâ pumps can beâ less expensive but vary in quality. When buying, verify the seller’s â¤return⢠policy and warranty; a short warranty (30-90 days) is common for aftermarket parts, while â˘OEM parts often carry longer coverage through the dealer.
Wrapping up
The 137221600 Frigidaire Washer â˘Drain Pumpâ plays a central role in the appliance’s ability to remove âwater efficiently at the end of wash and rinse cycles. As the component responsible for evacuating standing water,â maintainingâ properâ water flow and pressureand preventing backups or leaks, its⢠condition directly impacts cycle completion,â machine longevityand overall laundry performance. Using the correct part number ensures compatibility with the intended⣠Frigidaire models and helps preserve â˘design tolerances and electrical characteristics specified âŁby â˘the manufacturer.
Because symptoms such⢠as incomplete draining,unusual noise,persistent standing water,or related error codes can⢠originate from several causes,accurate âdiagnosis is âimportant before replacement. Inspecting hoses,filters,and electrical connections and confirming pump failure with âappropriate âtests can prevent unnecessary parts changes. When replacement is required, installing the â¤correct 137221600 Frigidaireâ Washer drain Pump and following safe, manufacturer-recommended proceduresâ restores proper operation and helps avoid collateral damage to the washer. Timely,â well-documented ârepairs are the most practical way toâ maintain performance and minimize longer-term repair⣠costs.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
