WR17X11267 GE Refrigerator Funnel Ice Dispenser is a molded funnel or chute assembly used in GE refrigerators with through-the-door ice dispensers; it is indeed a structural, non-electrical component that directs ice from the ice-making module or bin to the external dispense opening. The part is typically fabricated from a cold-resistant polymer and includes mounting tabs, flanges and sealing surfaces that locate it within the freezer door or dispenser cavity. As a mechanical guide, it provides the primary pathway for ice pieces and also forms part of the interface between the ice storage area and the door-mounted dispenser.
Within the appliance the funnel functions as a flow-control and alignment element: it channels ice to the dispenser opening, maintains proper clearance with the auger or agitator, and helps prevent ice bridging or backflow into the ice maker. It interacts directly with the ice maker/bin assembly, the dispenser actuator or paddle, any adjacent door sealsand the auger or motor-driven dispensing mechanism. Because it is exposed to repeated freeze-thaw cycles, mechanical abrasion from iceand the stresses of door movement, common service concerns involve wear at mounting points, cracks in the funnel body, and degraded seals that can allow ice jamming or air leakage into the ice storage area.
In this article readers will find a detailed explanation of the funnel’s function and typical installation locations,guidance on model compatibility and how to verify the WR17X11267 number against refrigerator models,common failure symptoms to recognize (visible damage,ice buildup,repeated dispenser motor overloads,or misalignment),step-by-step troubleshooting checks to isolate the funnel as the cause,and practical replacement considerations including access procedures,fastening methods,sealing surfaces to inspect,and basic post-replacement tests. The aim is to give technicians, engineersand appliance owners the technical context needed to diagnose funnel-related dispenser issues and to perform safe, correct replacement when required.
Table of Contents
- Functional Role and System Integration of the Funnel Ice Dispenser in GE Refrigerators
- How the WR17X11267 GE Refrigerator Funnel Ice Dispenser Operates: Mechanical Action, Ice Flow Pathand Seal Interfaces
- Common Failure Modes, Wear Patternsand Diagnostic Tests for the funnel Ice Dispenser
- Compatibility, Approved Appliance Models, Replacement Considerationsand Installation Procedures for the Funnel Ice Dispenser
- Q&A
- To Wrap It Up
Functional Role and System Integration of the Funnel Ice Dispenser in GE Refrigerators
The WR17X11267 GE Refrigerator Funnel Ice Dispenser is a molded funnel assembly that directs ice from the storage bin into the dispenser chute while isolating the dispensing pathway from the fresh-food compartment. Functionally, it provides a controlled feed area so cubes or crushed ice are routed cleanly into the auger or chute and engages with the dispenser door/flapper to prevent backflow of air and moisture. The funnel’s internal dimensions, lip geometryand sealing surfaces are designed to minimize bridging and jamming of irregular ice shapes and to maintain alignment with the dispenser actuator and any optical or microswitch sensors used to detect dispense events.
In system terms the funnel is a passive mechanical interface that must maintain dimensional accuracy and secure mounting to work reliably with the auger motor, dispenser actuator, and surrounding housing. technicians should inspect the funnel for cracks, warped mounting tabs, or deformed sealing edges when diagnosing intermittent jams, chopped ice at the chuteor false sensor trips; small deformations can cause misalignment that produces symptoms similar to motor or sensor failure. Replacement is ofen the correct remediation when the funnel shows physical damage or persistent deformationand verifying fitment and engagement with the dispenser door during reassembly prevents recurrence.
- Visual check for cracks or wear at mounting tabs and sealing lip
- Confirm alignment with the auger shaft or dispenser paddle and actuator arm
- Test for proper sensor activation or door closure after installing replacement
- Replace when deformation causes repeated jams or inconsistent dispense
| Item | Description |
|---|---|
| Part | WR17X11267 – molded funnel that channels ice from bin to chute |
| Function | Guide and isolate ice flow; maintain alignment with actuator and sensor elements |
| Common failure symptom | Ice bridging/jamming, chopped ice exit, false sensor trips, poor door sealing |
How the WR17X11267 GE Refrigerator Funnel Ice Dispenser Operates: Mechanical Action, Ice flow Pathand Seal Interfaces
The WR17X11267 GE Refrigerator Funnel Ice Dispenser directs ice from the ice maker’s auger or cutter into the user-accessible chute and cup, using a molded funnel shape to control trajectory and minimize chipping. Mechanically, the funnel mounts beneath the dispenser door and aligns with the auger/dispense train so that when the drive motor and clutch cycle, ice fragments or cubes are guided through the funnel’s tapered throat into the service opening. The part’s geometry and internal deflectors reduce turbulence and prevent cubes from striking the door or sensorand its low-temperature engineered plastic resists impact and stress from repeated dispensing cycles. In compatible GE refrigerator models the funnel also provides the mechanical interface for the dispenser actuator or door sensor so correct seating is required for reliable dispense sequencing.
The funnel’s seal interfaces control both water containment and the mechanical engagement between the dispenser mechanism and the refrigerator interior. A compressible foam or rubber gasket at the mounting flange forms a vapor- and drip-resistant barrier to the cabinet, while a molded lip around the throat prevents ice from wedging between mating surfaces; an actuator rod or micro-switch boot often uses a small O-ring or bellows to keep the electrical switch dry. Common operational issues-ice bridging at the funnel throat,water leaks onto the door,or failure to trigger the dispenser cycle-are typically traceable to worn or misaligned seals,cracked snap-fit tabs,or improper seating against the housing. For troubleshooting, inspect the mounting tabs and gasket for compression set, verify the funnel is fully seated so the actuator engages the switch, and check for hairline cracks in the throat that can alter flow dynamics and promote jams.
- Noisy dispense or grinding: possible misalignment or fractured internal ribs.
- Water on door or floor: damaged/missing gasket at funnel flange.
- Intermittent dispense: actuator not engaging due to improper seating.
- Frequent ice bridging: worn throat lip or excess moisture in ice production.
| Item | Description |
|---|---|
| Material | Low-temperature impact-resistant thermoplastic (molded),with rubber/foam seal elements. |
| Primary interfaces | Auger/dispenser outlet, dispenser housing flange, actuator/micro-switch interface. |
| Typical failure modes | Seal compression set, snap-fit tab breakage, throat abrasion causing jams, hairline cracking. |
Common Failure Modes, Wear patterns, and Diagnostic Tests for the Funnel Ice Dispenser
The WR17X11267 GE Refrigerator Funnel Ice Dispenser is a molded funnel and gate assembly that directs ice from the bin into the dispenser chute while sealing the bin from warm air and moisture. Typical wear patterns include brittle cracking of the thin plastic walls from impact or age, abrasion on the mating surfaces where crushed ice contacts the funneland deformation or breakage of mounting tabs that maintain alignment with the auger and actuator. Frost or mineral buildup on the inner surfaces can create ice bridges and increase friction, while misalignment of the funnel relative to the auger or paddle can cause partial jams, noisy operationor inconsistent dispensing. Compatibility considerations are mechanical: the funnel must match the refrigerator’s bin geometry, tab locationsand actuator clearance to function correctly; cosmetic differences can still affect performance if the interface dimensions differ by a few millimeters.
- Intermittent or complete ice jams during dispense
- Visible cracks, missing or loose mounting tabs, or distorted flange faces
- Noise or scraping when the auger runs
- Water or ice accumulation at the funnel/chute interface
| Item | Description |
|---|---|
| Cracked funnel | Through-cracks or fractured walls allow ice bridging and reduce sealing; replacement required when structural integrity is lost. |
| Worn or broken tabs | Loose or missing mounting features cause misalignment with the auger and actuator, producing jams or grinding noises. |
| Frost/mineral buildup | Surface deposits increase friction and can create temporary bridges; resolve with defrost and cleaning or replace if surface is scored. |
Diagnostic testing begins with a powered-down, emptied ice bin and visual inspection for through-cracks, tab integrity, and surface scoring.Perform a manual actuation check by operating the dispenser actuator (or moving the funnel gate by hand) to verify smooth travel and correct clearance to the auger; any binding, excessive playor contact during movement indicates wear or misalignment. Functional tests include running the auger motor with the funnel installed (power on, observing from a safe distance) to confirm unobstructed ice passage and listening for abnormal noisesand using a multimeter to verify continuity on any integrated switches.Practical examples: remove the funnel and attempt a dry-run auger test to isolate the jam source, or defrost and clean the funnel to determine whether deposits alone caused binding.Always disconnect power before disassembly and replace the funnel if you find a through-crack, missing mounting features, or permanent deformation that prevents consistent alignment with the auger or actuator.
Compatibility, Approved Appliance Models, Replacement Considerationsand Installation Procedures for the Funnel Ice Dispenser
WR17X11267 GE Refrigerator Funnel Ice Dispenser is the molded funnel component that channels ice from the ice maker assembly into the dispenser chute and helps prevent bridging and misfeeds.Its functionality is primarily mechanical: the funnel must align precisely with the auger, dispenser chute, and any actuator or sensor cutouts so that ice flows freely and does not contact rotating parts.Fit is the key compatibility criterion-matching mounting tabs, screw locationsand clearance envelopes determine whether the funnel will work in a given GE refrigerator model; technicians should confirm the model-specific parts list or exploded view before substituting the funnel, as different ice-maker families within GE refrigerators use different funnel geometries even when the ice maker appears similar.
When replacing the funnel, inspect surrounding components (auger, bin, door actuatorand any seals) and look for cracks, deformation, or buildup that could impair function; replaced funnels are commonly installed when recurring jams, false sensor activationsor shredded ice are observed.Basic installation procedures involve removing the ice bin and any retaining screws, verifying the orientation and seating of the funnel against the auger and chuteand confirming actuator/sensor alignment before reassembly; after installation, cycle the dispenser and run several dispense cycles to verify smooth flow and absence of interference.Practical considerations include using the correct fastener torque to avoid distortion, replacing adjacent seals if hardenedand confirming that replacement funnels are listed for the refrigerator’s model family to avoid repeated failures.
- Preparation: disconnect power, remove ice bin, document fastener locations.
- Removal: unfasten retaining screws/clips, lift out the old funnel, inspect auger and bin for damage.
- Installation: seat new funnel, align actuator/sensor cutouts, secure fasteners without over-torquing.
- Verification: restore power, run multiple dispense cycles and visually check ice flow and clearances.
| Item | Description |
|---|---|
| Function | Directs ice from the ice maker to the chute while minimizing jams and contact with moving parts. |
| Compatibility | Requires exact match of mounting features and clearances; verify against the refrigerator model’s parts list. |
Q&A
What is the WR17X11267 funnel ice dispenser and what does it do?
The WR17X11267 is a plastic funnel/chute assembly used on GE-style refrigerator freezers to guide ice from the ice bin or auger into the dispenser opening in the freezer door. It does not make ice or drive the auger - its purpose is to channel dispensed ice cleanly through the door and to help prevent jams and spills.
How do I know if the funnel (WR17X11267) is the cause of ice-dispensing problems?
Symptoms that point to a damaged funnel include visible cracks or missing pieces, ice falling out of the door instead of into the cup, frequent jams where ice packs up at the doorand gaps that allow light or drafts. If the auger motor runs and the ice maker is producing ice, but ice is not getting into the cup or spilling, inspect the funnel for damage or misalignment before replacing motors or switches.
How do I remove and replace the WR17X11267 funnel assembly?
General replacement steps: unplug the refrigerator or shut off power, open the freezer door, remove the ice bucket if presentand locate the screws or plastic clips that secure the funnel to the door inner liner. Remove the fasteners,gently pull out the old funnel (take care not to damage wiring or sensors),fit the new funnel into place,resecure with the original fasteners,reinstall the ice bin,and restore power. Because mounting details vary by model, consult your refrigerator’s service manual or the OEM instructions for model-specific steps.
What tools do I need to replace the funnel and how long will it take?
Typical tools are a Phillips-head screwdriver and possibly a nut driver (commonly 1/4″ or 5/16″), plus a flashlight. Expect 15-30 minutes for a straightforward replacement if there are only a few screws and no additional components to remove. If the door panel or wiring must be disturbed, allow more time and consult the service guide.
can I clean the funnel rather of replacing it, and how should I clean it?
If the funnel is simply dirty or has ice buildup, you can clean it. Remove loose ice and wash with warm (not boiling) soapy water, rinseand dry thoroughly. Avoid abrasive pads or harsh chemicals that can scratch or weaken the plastic. If the funnel has cracks, warping, or missing sections, cleaning will not restore proper function and replacement is recommended.
Where can I buy a genuine WR17X11267 and how do I ensure compatibility?
Buy from authorized GE Parts dealers,major appliance-part retailers,or the manufacturer’s parts website to ensure you get the OEM part. To ensure compatibility, check the part number printed on the old funnel or verify the refrigerator model number against the parts lookup on the manufacturer site. Many third-party sellers list compatible models, but cross-check with the OEM listing when possible.
Will replacing the funnel fix a jammed dispenser that won’t turn the auger?
Only if the jam is caused by the funnel being cracked, dislodged, or obstructing the auger. If the auger motor does not run at all, the problem may be electrical (motor, switch, controlor wiring) rather than the funnel. Diagnose by listening for the auger motor, checking dispenser switchesand ensuring the motor has power. Replace the funnel if it is physically blocking or misdirecting ice; otherwise continue electrical troubleshooting.
any safety tips or cautions I should follow when working on the ice dispenser/funnel?
Always disconnect power to the refrigerator before starting work. Remove ice and dry the area to avoid slipping and to prevent short circuits. Handle replacement parts gently to avoid cracking new plastic. If you must remove the freezer door panel or electrical connectors, label connectors and fasteners so you can reassemble correctly, and consult a qualified technician if you are not cozy with the procedure.
To Wrap It Up
The WR17X11267 GE refrigerator Funnel Ice Dispenser serves a focused but essential role in the ice delivery system, guiding ice from the storage bin through the chute to the dispenser. As a small mechanical component, it helps prevent jams, controls ice flow for consistent dispensingand contributes to overall user convenience and appliance reliability. Proper function of this funnel supports hygienic handling of ice and reduces wear on adjacent parts by ensuring smooth, predictable movement of ice pieces.
As symptoms such as dispensing jams, irregular ice flowor unusual noises can stem from this funnel or from related components, careful diagnosis is critically important to identify the true cause before replacing parts. When replacement is required, using the correct WR17X11267 part and following recommended installation and testing procedures helps restore performance and avoid repeated failures. For complex diagnoses or if safe access to internal components is limited,consulting an authorized technician will ensure the repair is done correctly and preserves appliance safety and longevity.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
