137353300 Frigidaire Washer Lid Lock â˘Switch is an electromechanical interlock assembly designed to detect and secure the lid position on⤠compatible âtop-loading Frigidaire â¤washing machines. As a discrete safety and control component, the part typically combines â¤a mechanical actuator with one or more electrical contacts or a small solenoid and is mounted at the lid catch to register âlid closedâ and â˘engage the lock duringâ specific âcycle phases.
Inside the appliance, theâ lid lock switch functions as both a safety interlock â˘and a control input:⢠it prevents the lid from being opened during high-speed spin or automatic cycle steps that âcould present a hazardand âit supplies the âwasher control board with the lid-status signal required to progress through âprogram states.The switch interfaces directly with the washer’s control module and associated â¤wiring harnessand indirectly with motor and brake control circuits âŁ(via the controller) âbecause the controller will not initiate or continue certain operationsâ unless a⤠closed/locked âsignal is â¤present. Mechanically,the assembly is located atâ the lid strike⣠area and must reliably operate under repeated âŁmechanical actuation and exposure to moisture and detergents.
This articleâ will âexplain the 137353300â switch’s function and typical electrical/mechanical characteristics, outline which Frigidaire models and part familiesâ it is compatible with, âand describe common failure symptoms such as intermittentâ operation, a stuck actuatoror open/shorted contacts. It will also provide practical diagnostic âstrategies âŁforâ technicians and owners â¤(visual inspection, continuity andâ voltage checks at the harnessand simple functional tests), troubleshooting guidance to distinguish switch failures from control-board or âŁharness faults, â¤and âreplacement considerations including â¤fitment, connector⢠orientationand verification steps after installation.
Table of Contents
- Functionalâ role, safety interlocksand system integration of âthe lid lockâ switch
- How the 137353300 Frigidaire Washerâ Lid Lock Switch operates: mechanical, electricaland⣠controlâboard interfaces
- Common failure modes and diagnostic â¤symptoms associated with lid lock switch faults
- Replacement âŁconsiderations, âmodel⤠compatibilityand stepâbyâstep installation guidance
- Q&A
- Closing Remarks
Functional role, safety interlocksand system integration of the lid lock switch
The 137353300 âFrigidaire Washer Lid Lock switch combines⢠a mechanical⤠latch and an electrical contact element⢠to enforce the â¤washer’s safety âinterlock during⢠agitate andâ spin cycles.⢠Mechanically, the latch engagesâ with a strike on the lid to prevent openingâ under rotation; electrically, an integrated microswitch âor contact set provides a closed/open status signal to the main control board and âaccepts the lock-enable âcommand from the⤠controller. Technicians should treat the⣠part as both a physical locking device and a sensor: correct function requires proper âŁalignment of the lid strike,intact mounting tabs,and anâ electrical connector that matchesâ the âwasher’s harness and control logic level.
- Primary behaviors: âŁsecures lid mechanically, reports lid-closed â¤state to the controland remains latched until the controller⣠releases it.
- Common symptoms of failure: washer⣠will not⢠enter spin, displays a lid or lock⣠erroror the latch remains stuck âŁ(either⢠open⤠or⢠closed).
- Typical tests:⢠verify continuity⢠of the switch with the lid engaged, confirm the control sends the âlock-enable signal during the spin phaseand visually inspect for â˘broken âlatch components or misaligned strike.
in⤠system integration, the lid âlock switchâ acts as a hard⤠interlock in â˘the safetyâ chain-control firmware will not apply power to the drive motor for high-speed operations unless it detects the locked âstate. If the switch â˘fails to assert, the⤠controller suppresses spin to prevent uncontained loads or user injury. When replacing the component, match theâ mechanical mounting and connector pinout to the original⤠part; use a multimeter to confirm contact continuityâ and, âwhere⣠applicable,â observe the presence âof the controller’s lock-enable⣠voltage⣠or logic signal whileâ commanding a spin cycle. Replacing the part⢠without correcting alignment or debris in â¤the strike area often results in repeat failures, so verify both mechanical⤠and â¤electrical interfaces before â˘concluding â¤the repair.
| Item | description |
|---|---|
| Function | Mechanical latch plus electrical interlock/signal⤠toâ the control board |
| Connector | Model-dependent harnessâ (commonly 2-3 pins); confirm pinout before installation |
| Failure modes | Stuck latch, burned contacts, misalignment,⤠or broken⤠mounting tabs |
How the 137353300 Frigidaire Washer Lidâ Lock Switch operates: mechanical, electricaland controlâboard interfaces
The 137353300 Frigidaire washer Lid Lockâ Switch is a combined mechanicalâ interlock and electricalâ switch assembly that secures the lid during agitateâ and spin â˘cycles and provides the control board with⣠lid-state feedback. Mechanically, âthe assembly uses a spring-loaded plunger or latch that⤠mates with a strike on the cabinet lid; âwhen the control board energizesâ the lock âŁactuator the âplunger⤠movesâ into the strike and resists forced opening. Wear, debris,â or misalignment of the plunger or strike will âprevent full engagement and will typically produce⤠a⤠lidâlock or lidâerror code⤠rather than a mechanical failure that allows âthe washer⣠to spin with the lid open.⢠Replacement compatibility requires matching the actuator geometry and connector positionâ so⣠the lid strike and mounting points line â¤up correctly onâ the cabinet.
Electrically, theâ part⤠contains multiple contacts that present at least one lid-closed/detection circuit and a lock/actuator⢠circuit toâ theâ machine controller. The âcontrol board issues a lock command⣠and âmonitors a sense circuit to confirm the âlock has engaged;⣠if⤠the âboard doesâ not see the expected âchange⢠in contact state it âwill halt progression to high-speed âspin. For practicalâ diagnostics a âtechnician can observe the control board drive signal during a lock command â¤and measure continuity across the switch’s terminals in both locked⣠and⤠unlockedâ positions to determine whether the fault is in the switch, âŁwiring,⤠or the board.â When installing a replacement, verify that terminal pinouts,⤠cable connector⣠typeand âthe actuator travel match the âoriginal so the control logic andâ mechanical interface behave as intended.
- Mechanical latch/plunger that engages lid strike
- Multi-contact switch for lid-detect and locked-stateâ feedback
- Electrical connector matching⢠control-board harness and pinout
- Mounting âpoints and âŁactuator geometry critical for âŁproper alignment
| Item | Description |
|---|---|
| Mechanical | Spring-loaded plunger/latch that physically preventsâ lid⣠opening while engaged. |
| Electrical | Multiple⣠contacts providing closed/locked sensing and an actuator circuit to the⣠control board; drive voltage âŁand sensing method vary by model-refer to⢠theâ washerâ wiring diagram. |
Common failure modes and diagnostic symptoms associated with lid lock switch faults
The 137353300 Frigidaire Washerâ Lid Lock Switch combines a mechanical latch and one or more electrical âswitch contacts that tell the washer control â˘board when the lid is closed and secured. In normalâ operation the control board energizes a latch or âreads âa â¤closed-contact feedback signal before allowing high-speed agitation or spin; a fault in â¤the latch, the microswitch contacts,⤠orâ the harness can interrupt that signal and prevent the machine from advancingâ through itsâ cycle. âtechnicians should note that this⤠part is a direct-replacement assembly for âŁspecified Frigidaire top-load models, so âfailures can be isolated to the assembly itself, the mating connectoror wiring rather than to unrelated components such as the motorâ or control board logic.
Diagnosing lid-lock problems requires âŁboth mechanical â˘and âelectrical checks: visually inspect the latch for broken plastics, foreign debrisor⣠bent actuators, then perform a continuity or resistance check âon the switch terminals while â¤manually operating the latch to â¤confirm âŁconsistent contact closure. Also verify the harness and connector forâ corrosion, burnt pins,⤠or loose crimpsand observe for intermittent faults that only appear during â¤vibration or temperature âŁchanges. If the⤠microswitch contacts are open, intermittentor if the latch binds⤠mechanically even though the control board isâ commanding â˘a lock (audible click with no feedback), replacement âof the 137353300â assemblyâ is the â¤practical remedy⢠because it ârestores⢠the âcorrect mounting, connector pinout,â and mechanical⣠geometry required by the washer.
- Washer will not start or advance cycles; lid-lock indicator stays on⢠or machine⢠displays a door/lid error.
- No spin or agitation even though other components appear to run.
- Lid⤠remains locked âafter cycle completes or will not lock at all despite an audible actuator â˘click.
- Intermittent operation: symptoms occur only under vibration,⢠after a warm-up periodor after reseating the⤠harness.
| Item | Description |
|---|---|
| No start âŁ/ door error | Controlâ sees open circuit; â¤check continuity across switch when latched and inspect harness connector. |
| Audible click but no lock feedback | Actuator poweredâ but microswitch contact failed-verify continuity during actuation; replace âassembly if contact is open. |
| Stuck locked or mechanical binding | Inspect latchâ forâ debris, â¤broken â˘teethor misalignment; replacement recommended if actuator â˘cannot fully âtravel. |
Replacement considerations, model compatibilityand stepâbyâstep installation guidance
The 137353300⢠Frigidaire Washer lid Lock Switch isâ an electromechanical interlock âthat confirms the washer lid is latched and provides the control board with âa⤠definitive closed/openâ signal during wash and spin cycles. Technically, the component contains one or â¤more switch contacts and a mechanical latch or solenoid interface so âŁthe⢠board â˘can inhibit drum rotation or enable high-speed⣠spin only when the contacts indicate a secured lid. Typical failure⣠modes include âintermittentâ continuity,â bent actuator⤠tabsor â¤corroded connector pins;â these⢠failures produce symptoms such as refusal to⣠start,⣠repeated lidâlock error codesor⢠a washer that⣠pauses midâcycle. Before â˘replacing the part, compare the OEM part number, connector⢠pin count, mounting hole pattern,⢠and actuator âgeometry to ensure physical and electrical compatibilityand verify⣠that replacement âunits use the same switching arrangement (normally⣠open vs.normally closed) â˘required by the machine’s control logic.
- Disconnect power â to the washer at the breaker and, âif the tub containsâ water, stabilize or drain the load⢠to prevent spills.
- Document âor photograph the connector and actuator orientation, then remove the lid or access â¤panel screws to reach the switch assembly.
- Unplug the wiring harness and â˘remove the mounting fasteners; swap the â˘old switch for the new unit, confirming theâ replacement’s⤠pins andâ latch⢠fit without forcing the assembly.
- With the new switch installed, check continuity acrossâ the appropriate terminals with a multimeter while manually actuating the latch to âŁconfirm open/closed behavior before reassembly.
- Reassemble panels, restore powerand âŁrun a âshort âtest cycleâ or the washer’s diagnostic routine to confirm⤠normal locking behavior and absence ofâ error codes.
Practical considerations include using a âmultimeter to measure resistance values-closed contacts shouldâ read near 0 Ί-while the control board’s wiring harness â˘should beâ inspected for heat damage that can mimic a⢠switch failure. â˘If the replacementâ uses a different mounting bracket or connector, adaptors or minor âbracket âfabricationâ might potentially⢠be â¤necessary, but avoid modifying the control harnessâ wiring;â rather, use a factoryâstyle harness adapter or source the exact OEM connector. For technicians, keeping a reference photo and checking the washer’s service manualâ for diagnostic LEDâ patterns or â¤error code⢠interpretation speeds âverification and avoids repeated disassembly.
| Item | Description |
|---|---|
| Typical terminals | 2-3 pins; check âfor NO/NC âcontact arrangement |
| Expected continuity | Closed â 0-5 Ί, Open = OL (infinite) |
Q&A
What⢠is the Frigidaire part 137353300 lid â˘lock⣠switch?
137353300 is the OEM lid lock (door interlock) assembly â¤used on⤠certain Frigidaire washing machines. It electrically and mechanically secures the lid âduring portions of the cycle so the⢠washer will lock, runand spin safely. The assemblyâ contains the switch contacts⢠and⢠the latch/sensor that detects whether the⣠lid is closed and locked.
What symptoms indicate the lid lock switch has failed?
Common signs include: the washer will not start or will not progress past the âdoor/lid â¤lockâ step, the washer starts but the lid won’t lock, âthe spin cycle won’t beginor intermittent operation where the lid works sometimes and not other times. You may also notice error codes or indicator â¤lightsâ related â¤to the door/lid on some⤠models. Physical symptoms include⢠a broken or stuck⢠latch or visible damage to the lock assembly.
How can I test the 137353300 âlid lock⢠switch â˘safely?
Always disconnect power before testing. Remove the access panel⢠to reach the â¤lock and unplug the harness. With a multimeter set to continuity or ohms, check the switch terminals for the expected change when the lock â¤is manuallyâ actuated (lid closed vs. open).The switch should â˘show continuity in the locked position and open in the unlocked position (or vice versa depending on the terminal pair). âŁIf unsure⢠which⢠terminals to test,⣠consult â˘the service manual for your model. Do not probe live circuits unless you areâ experienced and take proper safety precautions.
Can I â˘replace the â˘lid lock âswitch myself â˘and whatâ are the basic steps?
Yes, many ownersâ can â˘replace it.⢠Basic steps:â 1) Unplug the washer â(turn off power at the breaker if â¤needed). 2) Access the lock (top or front panel dependingâ on model) â¤by removing screws/fasteners. 3) Disconnect the wiring harness from theâ old âlock and remove any mounting screws. 4) Install the new 137353300 unit, reconnect the harnessand âreassemble panels.5) Restore power andâ run aâ short cycle⤠to verify operation. âFollow⣠theâ service manual âŁfor your specific model and⢠if â˘you’re notâ cozy working with electrical appliances, hire a technician.
How do Iâ confirm the 137353300 is compatible with my washer model?
Find your washer’s full model⤠number (usually on a sticker inside âŁthe door âframe, behind the top panelor on the back). Cross-reference â˘that model number with âŁthe Frigidaire parts list or with the seller’s compatibilityâ chart. do not relyâ solely on photos – check that 137353300 is listed for â¤your exact model or that âŁthe seller confirms compatibility before buying.
Should Iâ buy the OEM 137353300 or⣠an aftermarket replacement?
OEM â˘(Frigidaire) parts like⤠137353300 â˘are⢠built to original specifications and generally offer reliable fit and function. Aftermarket parts can be less expensiveâ but quality varies;⣠some will work⤠fine, others may have fitment or durability issues. âŁIfâ you wont the best assurance of a correct âŁfit and warranty support, choose the OEM part. If cost is a concern, buy from âa reputable aftermarket âsupplier with good return/warranty policies.
How much does the lid lock switch replacement typically cost?
Part-only prices⢠for the⢠lid âlock assembly typically range from about⤠$20 to $80 USD depending on source and whether it’s OEM or aftermarket. If you hire âa technician, labor will add to the cost-expect an additional service call/labor charge. Prices vary by region and supplier, so check multiple vendors and factor in shipping orâ service fees.
If replacing the lock â˘doesn’t fix â¤the âŁproblem, what else should Iâ check?
Check the wiring harness and connectors for corrosion,⢠loose âŁpinsor⤠broken wires. Verify the lid strike/hinge alignment so the lock can engage properly. if wiring and the new lock are good but the washer still won’t lock or advance, the control board or timer may be â¤faulty â(it may not be sending the lock signal). âRun the washer’s diagnostic mode if available to see if the control is commanding the lock. If you’re unsure, have a â˘qualified technician diagnose further to avoid replacing unnecessary⢠parts.
Closing⣠Remarks
The 137353300 Frigidaire Washer Lid Lock switch serves as a âcritical safety and controlâ component, ensuringâ the washer lidâ remains⣠securely⣠locked⢠during wash and spin cycles âand communicating lid status to the machine’s control system. Properâ functioning of this switch helps prevent accidentalâ lid opening,enables cycle completion,and reduces the risk of âwaterâ spillage orâ mechanicalâ damage,making⤠itâ an integralâ part of reliable washer operation.
Accurate diagnosis and âtimely replacement of a failing lid⤠lock⣠switch are important to restore both âsafety and functionality.⢠Diagnosing the issue-through observation â¤of error âcodes, continuity testingand visual inspection-helps confirm that the switch is the root cause â˘before replacement. When replacement is necessary, using the correct 137353300 part, following â¤the⢠manufacturer’s installation instructionsand observing electrical safety âprecautions will help ensure a⤠proper and lasting repair. If uncertainty remains, consultation with a qualified service technician can prevent misdiagnosis and improper â¤installation.
attention⤠to the condition and âŁcorrect replacement of the 137353300 Frigidaire âWasher Lidâ Lock âSwitch supports safe operation, reliable performanceand reduced downtime. prompt, âinformed action when âproblems arise helps maintain the washer’s intended performance and prolongs the appliance’s useful life.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
