WD24X10062 GE Dishwasher drain Tube Assembly âis a âmolded drain hose and fitting assembly⤠used to carry âwastewater from the dishwasher sump and drain pump to the household drain or disposal. As a plumbing component of the appliance, it typically consists of a âflexible or semi-rigid hose section⣠with⣠integral fittings, clamps and sometimesâ a check âvalve or molded connector âŁdesigned⢠to⢠mate â¤with the dishwasher’s drain pump outlet and the home plumbing âconnection.
Inside the dishwasher system⤠the drain tube assembly interfaces directly with the drain pump, âsump, filter basketand any installed air âgap or disposer connection. Its primary⤠role is to provide⤠a low-resistance, sealedâ path for pumped wastewater so that the pumpâ can evacuate the tub withoutâ leaks or backflow. Proper⤠routing, secureâ connections and the presence of a high loop or air gap are critical to prevent siphoning or âcontamination â¤of the wash chamberand the tube’s material⣠and geometryâ influence hose âlongevity, clog susceptibility and ease of service.
This â˘article explains theâ WD24X10062 part’s function and⣠typical installation context,how to verify compatibility with specific GE âmodels,common failure â¤symptoms to watch for (for example â¤leaks,slow draining,gurgling or persistent water in the tub),and diagnostic checksâ technicians can perform to isolate tube-related faults. It also covers practical âtroubleshooting steps and replacement considerations such⢠as verifying part numbers and fitment,â inspecting mating components⤠(pump âŁoutlet, clamps, airâ gap/disposalâ connection), recommended routing and securing practices, â¤and verification tests âŁto confirm a âaccomplished⣠repair.
Table of âContents
- Function⣠and Role of the Dishwasher Drain Tube in Wastewater Ejection, AirâGap Management,â and backflow Prevention
- How the WD24X10062 GE Dishwasher Drain âTube Assembly Works Inside the Appliance: Flow Path, Connection Interfaces, âand Sealing Mechanisms
- Common Failure âSymptoms âand âDiagnostic Indicators of Blockage, Leakand⤠Venting Faults
- Replacement Considerationsâ and Installation⤠Procedure forâ WD24X10062 GE⤠Dishwasher Drain Tube Assembly: Tools, Fitmentandâ Leak Testing
- Q&A
- In Conclusion
Function â¤and â¤Role of the Dishwasher⤠Drain Tube in Wastewater Ejection, AirâGap âmanagement,â and Backflow Prevention
The WD24X10062 GE Dishwasher Drain Tube⢠Assembly is aâ flexible drainâ hose that âchannelsâ pump-discharge âŁwater from the dishwasher âŁtub to the household drain orâ garbage disposal while accommodating the required routing â˘andâ connection geometry. The âassembly matches the pump outlet and standard drain fittings⤠on âcompatible GE modelsand its âinner diameter, material flexibilityand âreinforcement determine flow capacity, âresistance to kinkingand âthe ability to maintain a reliable seal under the âcyclical pressure pulses produced by the drain pump. Proper sealing â˘at⢠both â¤the dishwasher and drain ends and⣠maintaining a continuous downwardâ slope are necessary âto avoid standing water in the tub or recurrent drainage cycles causedâ by partial siphoning.
Drain⢠tubes do not substitute for an externally installed⢠air gap or a proper high loop; the drain hose must be routed to work with either âan atmospheric air gap device or a roofed high⣠loop above the sink tailpiece to⣠prevent contaminated backflow. If âthe tube is â¤connected directly to a disposal inlet without an⣠air gap and the garbage disposal or householdâ plumbingâ develops a blockage, wastewater â˘can be forcedâ back âinto theâ dishwasher â¤during a downstream pressure event. Common failure modesâ to watch for include cracks, softening from chemical exposure, internal âobstructionsand clamp⤠failure-each of which impairs âŁejection⢠performance and increases âthe risk of⣠backflow.⤠Technicians should verify secure⤠clamps, correct routing heightand hose integrity during diagnosis and replacement.
- Compatibility â˘check: confirm pump outlet diameter and clamp type â˘before installation.
- Routing: maintain a â˘high loop or connectâ to an air gap âat the required elevation.
- Inspection: âŁlook for âŁcracks, brittlenessor internal â¤debris when⤠performance issues âarise.
- Disposal connection: âensure knockout on disposal is removed and âa proper seal is made.
| Item | Description |
|---|---|
| Part number | WD24X10062 â¤GE Dishwasher Drain Tube Assembly |
| Inner diameter | Typically 5/8″-3/4″ (verify againstâ model specifications) |
| Material | Flexible reinforcedâ polymer âŁresistant to detergents and âŁheat |
| Typical features | Pre-formed ends for pump and tailpiece connection; clamp retention surfaces |
How the WD24X10062 GE Dishwasher Drain⤠tube â¤Assembly Works Inside the appliance: Flow Path, Connection Interfacesand Sealing âŁMechanisms
The⣠WD24X10062 GE Dishwasher Drain Tube Assembly functions as the conduit that evacuates used wash water⣠from the dishwasher sump and âpump assembly to the âhouse drain or garbage disposal. During the drain⢠cycle the pump forces water âinto the⢠discharge port⤠and throughâ this tube; the tube’s interior surface and diameter â¤are âdesigned to minimizeâ flow restriction and to resistâ detergent, heat âŁand repeated â¤flexing. Typical installationsâ route theâ tube âupwardâ to an air gap or over a high loop before descending âto the sink drain to prevent backflowand the material and shape âof â˘the assembly accommodate bends required by âcabinet andâ plumbing layout while preserving an unobstructed flow path to reduce theâ risk â¤of clogging or⣠standing water in the hose.
Connection interfaces are normally a molded hoseâ end â¤that fits a pumpâ discharge spigotâ or âdisposal inlet and is secured with aâ mechanical clamp or crimp. Sealingâ is achieved by âa tight interference fit at⢠the hose barbâ plus a corrosion-resistant clampor byâ a molded grommet or O-ring where the tube seats into a housing; these redundant⢠sealingâ methods prevent leaks under the transient pressures produced by the pump.â Practical service considerations include ensuring the âtube is routed with a continuous downhill slope after the high loop, replacing worn âclamps with stainless-steel âworm-drive clamps, inspecting for soft â¤spots or cracks that indicate âchemical/thermal degradationandâ confirming the assembly’s fit to the OEM pump/disposal interface âto avoid misalignment â˘that leads to leaksâ orâ premature failure.
- Key features: flexible⤠routing, chemical resistance, smooth bore for debris passage.
- Common interfaces: pump hose â¤barb, disposal/sink nipple,â clamp or grommet seals.
- Maintenance tips: check clamps, remove kinks, replace âifâ hardened or cracked.
| Item | Description |
|---|---|
| Flow âpath | From âŁpump âŁdischarge through⤠tube toâ air gap/disposal with a high loop to â¤prevent backflow. |
| Connection âŁinterfaces | Hose barb and clampor molded grommet/O-ring into pump/disposal fittings. |
Common âFailure Symptoms and Diagnosticâ Indicators of⢠Blockage, Leakand Venting Faults
The WD24X10062 GE Dishwasher Drain Tube â˘Assembly conveys wastewater from âthe tub to the household âdrain and participates in the system that âpreventsâ backflow⤠and siphoning. A partial â˘or full blockage increases hydraulic backpressure, causing longer pump run-times, audible⤠cavitation or humming from the drain pumpand standing water in the sump; leaks present as dripping⣠at âhose joints, â˘wet cabinet bases,⤠or stainsâ beneath the â˘dishwasher and commonly â˘result from loose clamps, damaged fittingsor abrasions in the tube material; venting faults-such as a clogged air gap, âincorrect high-loop âroutingor an absent air gap-produce gurgling at âthe â¤sink, intermittent or slow âdrainageand occasionalâ siphon-back into â˘the tub. Confirm that the⢠replacement assembly matches the appliance’s⤠routing, â¤length,⣠and connection type because mismatches affect the installation andâ venting behavior.
- Slow or incomplete drain â¤- typically causedâ by partial obstruction in the tube, âŁtrapor disposer inlet.
- Water on floor or⣠cabinet â-⣠localize to tube run and fittings⤠to find clamps, splitsor punctures.
- Gurgling⢠or backflow into âsink – indicates air gap blockage, improper high-loopor negativeâ pressure in the drain line.
- Pump humming âwith ânoâ discharge – suggestsâ a sealed-off hose or internal blockage at the pump outlet.
- Foul odor fromâ dishwasher – stagnant water trapped in⣠a sagging section â˘ofâ the tube or a clog at the âoutlet.
diagnose faults by combining visual⤠inspection with âsimple flow and electrical checks: run a drain-only â˘cycleâ while observing hose routing and connection points for âleaks or movement, remove the trap/filter to⣠confirm free flowand â˘measure âpump current âfor overload that indicates restricted flow.⣠For practical troubleshooting, â˘disconnect the drain tube at the⢠pump outlet (catching residual water) to verify âif the⢠pump âcan expel water directly; if it can, the blockage or venting fault is downstream.Use a dye test or paper towelâ around joints to detect âŁslow â˘leaksand ensure the assembly is secured âwith proper clamps and âŁrouted withâ a high-loop or air gap to⤠prevent siphoning.
| Item | Description |
|---|---|
| Slow drain | partial obstruction in tube/trap or âŁdisposer âinlet restricting flow. |
| Leak at connection | Loose⤠clamp,degraded gasket,or tube cut; inspect and â¤replace â¤clamp or tube as needed. |
Replacement Considerations â¤and Installation⣠Procedure for âWD24X10062 GE Dishwasher drain Tube assembly: Tools, fitmentand Leak Testing
The â˘WD24X10062 GE dishwasher Drain Tubeâ Assembly â¤functions as âtheâ flexible conduit that routesâ wastewater from the dishwasher sump to the household drain â˘or disposer, â¤and must preserve internal â˘flow â˘characteristics⣠while resisting kinking, high âŁtemperaturesand exposure to detergents and grease.â This part typically uses barbed connections and⤠a clamped⣠joint to⤠the pump outlet and the drainâ stub; â¤matchâ the connector diameter, barb profile,â and overall length to the original â¤assembly to âensure proper sealing and routing. Verify the WD24X10062 â˘GEâ Dishwasher⤠Drain Tube Assembly against the appliance’s service manual or OEM part number before replacement,⤠and âinspect the routing path used by the factory-recreating âthe high âŁloop or âair gap location is necessary⣠to âprevent siphoning â¤and to â˘maintain proper drain performance.
Replacement requires â¤basic hand tools and attention⤠to fitment details to prevent leaks and â¤flow restriction.After ⣠shutting â¤off power and water, remove lower access panels and the⢠lower rack to reach the sump and drain connection; release the old clamp(s), detach âthe tubeandâ clean âthe pump â¤spigot and drain stub of debris before installing the new tube. secure theâ new tube âwith⤠appropriately sized hose clamps or â¤OEM-styleâ spring clamps, route it so there are no tight bends or contactâ with the heating elementand perform a leak test by running a drain-only or short wash âcycle while observingâ all connections for seepage. If the dishwasher drains slowly after installation,⢠check for internalâ obstructions, incorrect routing that creates a low loop, â¤or a partially collapsed tube at⢠tight âbends.
- Inspect connector diameter, clamp type,â and length before install.
- Maintain a âŁhigh loop/air gap to âŁprevent backflow.
- Tighten clamps âuntil snug;⣠avoid over-compression âthat deforms the â¤tube.
- Run at least one short cycleâ and inspect âŁforâ leaks⤠at both ends.
| Item | Description |
|---|---|
| Common tools | Flat-head screwdriver or nut âdriverâ for â¤screw clamps, âŁpliers for spring clamps, utility light |
| Fitment check | Measure innerâ diameter âat barbed⣠ends, compare length and routing clips to original |
| Leak test | Run a drain âcycle and â˘inspect â¤connections; âŁcheck under unit and at⤠disposer junction |
Q&A
What is⢠the WD24X10062 drain tubeâ assembly?
WD24X10062 is an â˘OEM GE dishwasher drain tube assembly (replacement drain hose) used to⣠carry âwastewater from the dishwasher â˘to the sink drain, garbage disposer⤠or air gap. It is indeed sold as a direct-fit replacement part for â˘many GE built-in dishwasher models. Always verify compatibilityâ with your dishwasher model ânumber before ordering.
What âsymptoms indicate theâ WD24X10062 needs to be replaced?
Common â¤signs⤠include visible cracks or⢠splits in the hose,persistent leaks under the âdishwasher,water left in the tub â˘after a âdrain cycle,foul⢠odors that âcome from the hose,or a soft/crumbly hose âŁmaterial. âReplacing the⢠hose is recommended if youâ see â¤damage,hardening,or repeated clogging.
How do I remove and install the WD24X10062 drain tube â¤safely?
Turn off powerâ to the dishwasherâ at the breaker and âshut off the hot water supply. pull the â¤dishwasher forward (support â˘it) and âremove âthe toe-kick if needed.â Place towels to⤠catch âwater. Locate the drain hose connections at the âdishwasher âpump and at the âŁsink/air gap/disposer. Loosen the âhose⢠clamps â¤(screw or spring clamps) and detach the hose-expectâ some waterâ to spill. Install the ânew hose by seating it fully âŁon the pump outlet and on the sink/disposer/air gap fitting, then tighten the clamps⢠securely. â˘Reposition the dishwasher, restore âwater and⤠powerand run a â˘short drain â¤cycle to check for leaks.
What tools and materials do I need â˘for replacement?
Basicâ tools: flathead or âPhillips screwdriver (for worm-gear clamps), hose clamp⢠pliers or âregular pliers (for â¤spring clamps), adjustable pliers, towels/absorbent âŁrags. Optional: flashlight, âbucketandâ work gloves. If the replacement kit does notâ include clamps,purchase appropriately sized stainless steel worm-gear⤠clamps.
how should the âdrain tube be routed? Do I need an air gap or aâ high âloop?
The âdrain âhose must be routed so backflow into the dishwasher is âprevented. Either⤠connect to a factory-installed air gap on the âcountertop or create a high loop by securing theâ hose as high⢠as possible underâ the countertop before it âdrops to the sink drain/disposer.â Follow âlocal plumbingâ codeâ and theâ dishwasher manufacturer’s⣠instructions-do not âŁallowâ the âhose to sag or be âkinkedand use clips or⢠straps to⢠secure it.
Can I â¤clear a cloggedâ WD24X10062 or âshould â˘I replace it?
Minor clogs â¤can often be âcleared by detaching⣠the⢠hose and flushing it with water, using a long flexible âbrushor⤠running water⢠through âŁfrom the pump end. Avoid caustic⣠chemical drain cleaners (they can âdamage hoses).Replaceâ the⣠hose if itâ is damaged, âhardened,⤠or continues to clog frequently-replacement âŁis usually the⤠more reliable long-term fix.
Does the⣠WD24X10062 kit include âclamps âand⢠fittingsor do I âneed to reuse the old ones?
Contents vary by seller. Some replacement assemblies include new clamps and fittings;⢠others are just the hose. Inspect your â˘kit before starting: ifâ clamps are missing⢠or old clamps are âcorroded/damaged, install new⢠stainless steel âworm-gear âŁor âquality spring clamps to ensure a leak-free seal.
Isâ it okay to use an aftermarket hose instead of the WD24X10062 original â¤GE part?
Aftermarket drain hoses can work if they match the âOEM âhose in diameter, length and fitting type,â but⣠OEM parts âŁ(WD24X10062) are recommended⢠to âensure fit⤠and material compatibility. Ifâ you choose an⢠aftermarket hose, verify â˘the inner/outer diameters and that â˘it’s rated for dishwasher â˘drainâ use; always check for leaks and proper routing â¤after installation.
to sum⤠up
The WD24X10062 GE dishwasher drain âtube â¤assembly plays a centralâ role in channelingâ wastewater from the âtub to the âdrain pump and ultimately out of the appliance. As a dedicated connection point within theâ dishwasher’s fluid path, it helps⤠maintain proper drainage, âprevents backflowand reduces⢠the risk of leaks and water damage when intactâ and âŁcorrectly installed. Because it interfaces directly with moving parts⤠and frequentâ temperature and pressure changes, âthe assembly is subject to âwear, âclogging, âand deterioration over⢠time, which can compromise overall âŁdishwasher performance.
Accurate diagnosis of drainage problems âis essential before replacing the drainâ tube assembly. âŁSymptoms such âas âstanding water after âa cycle,⢠drainageâ error codes, â¤unusual noises during pump operationor visibleâ cracks and blockages warrant inspection of the drain tube along withâ related components (pump, filters, hosesand⤠air âŁgap). âReplacing the WD24X10062 assembly when inspection confirms damage or failure restores proper drainage⢠and helps prevent secondary issues,⤠such as âpump overload orâ cabinet âŁwater damage.
when replacementâ is required, using âthe correct âpart â˘and following manufacturer-recommended procedures helps ensure safe, reliable operation â¤and compatibility withâ the dishwasher’s plumbing and pump system.⢠Routine checksâ for⤠obstructions, secure connectionsand signs of⣠wear can⤠extend âthe â˘life â¤of the âassembly and âsupport consistent dishwasher performance, while professional service or reference to officialâ service documentation canâ assist âin more complex diagnosesâ and installations.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
