WX14X10005 GE Washing 4′ Polymer âCoated Water Inlet Fill âHose 2 Pack is a replacement âset of two fourâfoot flexible water⣠inlet âhoses used to connect the household âŁwater supply to a frontâload⤠or topâload washing machine. The assembly consists of flexible â˘inner tubing⤠with a protective polymer coatingâ and factoryâfitted threaded ends âdesigned to mate with the supply shutoff valves and the appliance inlet ports; it is intended to carry potable water at typical residential pressures and⣠temperatures.
Inside the appliance system these hoses serve â¤as the primary conduit for hot and cold water into the washer, delivering⢠flow to the machine’s inlet valve(s) and filling circuits. They therefore â˘interact directly with the supply â¤shutoff, threaded fittings, inlet valve solenoids, water level/pressure sensing componentsand the machine⣠cabinet; their⢠condition affectsâ flow rate, âŁfilling timingand leak containment. The polymer coating⢠reduces external abrasion and limits corrosion exposure to the braided hose core, while hose integrity and âproper connections are critically âimportant for safe, predictable â˘operationâ and toâ prevent water damage from drips or ruptures.
In this article readers âwill find a technical overview of the hose’s function and common physical and dimensional compatibility considerations,symptoms â˘that indicate hose failure (for example visible cracks,bulging,seepage at fittings,reduced or intermittent filling,or⢠water on the floor),and a methodical approach to troubleshooting whether the âhose or another system element is at fault. The article will also cover practical⣠replacement âconsiderations – correct length âŁand endâfitting type, pressure and temperature ratings, inspection of washers and fittings, recommended installation⤠precautions (shutting off the supply,⣠relieving pressure, proper torque on fittings)and⣠factors to consider âwhen selecting a replacement to ensure reliable service without overstatement of performance.
Table of Contents
- Function and Role âof the Water Inlet â˘Fill Hose in Washing Machine Water Supply and Safety â¤Systems
- How theâ WX14X10005 GE Washing 4′ Polymer coated Water Inlet âŁFill Hoseâ 2 Pack Integrates with the âŁInlet Valve, Pressure Switch, â¤and Internal water⣠Pathways
- Common Failure Symptoms and Diagnostic Indicators âfor Leaks, â˘Restricted Flowand Pressure Irregularities
- Compatibility⢠Matrix, Replacement Considerations, Step-by-Step Installation Proceduresandâ Post-Installation Troubleshooting
- Q&A
- The Way Forward
Function and â˘Role of the Water Inlet Fill Hose in Washing Machineâ Water âSupply and Safety âSystems
WX14X10005 GE âŁWashing 4′ Polymer Coated Waterâ Inlet Fill Hose 2 pack â is a replacement inlet hose assembly designed âto deliver householdâ water to the washing machine inlet valve while providing a durable external barrier. The hose consists ofâ a flexible reinforced inner core that âŁtransmits pressurized water and an outer polymer coating that resists abrasion, chemical attackand external âwear. In operation the âinner core flexes andâ accommodates machine movement and vibration; the polymer coating âacts as secondary containment against pinhole leaks andâ wear from rubbing against chassis âedges or other components. The 4-foot length provides additional routing adaptability for appliances set away from wall valves or in stacked/laundry closet configurations.
Compatibility âand safe behavior⣠depend on correct matching of connector geometry, âroutingand periodic inspection. Theâ hose uses the common 3/4-inch female connector geometry found on⢠most âresidential washer⢠inlets, but technicians â¤should verify âŁthread form and inlet gasket condition before installation. Proper installation practices include⢠routing to avoid kinks, supporting the hose to prevent static bending at⤠the fittingsandâ tightening the nut to a hand-tight plus partial-turn rather â˘than high torque to avoid deforming the ferrule or washer. Replace the hose âif you⤠observeâ bulging, softâ spots, cracking in the outer coating,â persistent mineral buildup at⢠connectionsor visible rust⤠on metal fittings;⢠after installation, pressurize the⤠line and inspect all joints for leakageâ for at least one full âwash cycle.
- primary function: convey pressurized supply water âto the washer inletâ valve while allowing âŁmovement and vibration absorption.
- Safety feature: polymer âŁcoating provides an outer barrier to abrasion and secondary leak containment.
- Installation checks: verify connector type, avoid⣠over-tightening, routeâ without sharp bendsand test under pressure.
| Item | Description |
|---|---|
| length | 4 feet (per hose) |
| Coating | Polymer outer âŁlayer for abrasion and corrosion resistance |
| Fittings | Standard 3/4-inch female connector geometry (verify before installation) |
| Pack quantity | 2 hoses |
How the WX14X10005 GE Washing 4′ Polymer â¤Coated Water Inlet Fill Hose 2â Pack âŁIntegrates â˘with the Inlet Valve, Pressure Switchand âInternal Water Pathways
The WX14X10005⤠GE Washing 4′ â˘Polymer Coated⢠Water Inlet Fill Hose 2 Pack â˘serves as the physicalâ conduit between the household supply and the washing machine’s inlet valve assembly. Itâ uses standard threaded connectors to attach to the supply and the machine inlet; correct matingâ and a compressive seal at those⢠joints are necessaryâ to⣠prevent leaks and pressure loss. The polymer coating reduces external abrasion, wear from ârepeated handlingand galvanic reaction at the hose exterior, âŁwhile the internal hose wall must remain flexible and unobstructed âto preserve nominal flow⤠rates. Using the supplied length and fittings maintains compatibility with typical GE washer inlet geometries without requiring adapters âin most installations.
The hose does not contain control components, but⣠its⣠hydraulic behavior âdirectly affectsâ the inlet valve, the machine’s internal⣠water pathwaysand âŁthe pressure sensing system. When the inlet valve solenoid opens, the âhose must deliver sufficient volumetric flow so internal passages fill within the expected time window; reduced flow from kinks, sedimentor collapsed liners can cause extended fill times or fail-to-fill faults because the â˘pressure/air-actuated âŁlevel switch does not see the⣠expected pressure rise. Practical maintainance examples include inspecting⢠the hose screen (or theâ valve inlet screen) for mineral buildup, replacing a partially crushed hose to⢠restore â¤fill rateandâ verifying torque and washer condition at threaded joints to eliminate leaks that can mask as inletâ valve failures.
- Common symptoms tied to hose issues: slow âfill, intermittent filling,â leaks at fittingsor erratic level switch behavior due to delayed pressure rise.
- Quick⣠checks: verify hose routing for kinks, inspect âinlet screens for sediment, âŁand confirm secure threaded connections âŁwith appropriate sealing⢠washers.
| Item | Description |
|---|---|
| Hose | Delivers water from supply to inlet⢠valve; polymer coating protects external surface and handling durability. |
| Inlet valve | Electricallyâ actuated, meters hot/cold into internal pathways when energized; requires adequate â¤supply pressure and flow. |
| Pressure/level switch | Detects waterâ level âvia air pressure⣠in the internal âtube; dependent on timely â¤increase in pressure âproduced by unobstructed inlet flow. |
Common Failure Symptoms⤠and Diagnostic Indicators for Leaks, Restricted Flowand Pressure â˘Irregularities
The⣠WX14X10005 GE Washing 4′ âŁPolymer Coated Water Inletâ Fill Hose 2 Pack serves â˘as the supply connection between theâ household water âlines âand â˘the âŁwasher inlet valve; its polymer coating â¤protects the exterior braid from abrasion and corrosion but âdoes not prevent internal obstructionâ or valve-related failures.Leaks typically âŁpresent as visible⤠moisture at the hose⤠ends, wet floor near the washeror pressure loss at the inlet valve and commonly stem from degraded end fittings, collapsed inner linersor abrasions through the braid. Restricted flowâ andâ pressure irregularities are⢠usually caused by kinking,internal collapse â˘from age,accumulated mineral deposits,inline debris trapped at âthe connection,or partial closure of isolation valves; these â˘conditions reduce flow rate,increase fill time,and can produce audible âwhistling or sputtering at âthe inlet valve âevenâ when the external â¤hose appears intact.⤠The hose is intendedâ for standard residential washing machineâ inlets, so compatibility checks should include confirming correct threaded fittingsâ and âŁseating of the rubber washers at each end.
Diagnosis begins with a systematic inspection and isolation of variables: visually inspect the⤠full hose length âfor bulges, pinholesor abrasion marks and flex theâ hose while observing for leaks under pressure. Measure inlet pressure with a gauge or⤠time a known fill volume to quantify reduced flow; compare the result to expected⢠householdâ supply behavior to determine whether the issue is the hose, the shutoff valveor âthe washer inlet valve/solenoid. If internal blockage is suspected, remove and flush the hose into aâ bucket⣠to check for debris andâ restore unrestricted flow; if external damage or hose collapse⢠is evident, replacement with a⣠component such as the WX14X10005 setâ is appropriate. Useful⤠diagnostic cues and quick checks are summarized below.
- Visible leak: Water at fittings, soaked insulationor continuous dripping-inspect end fittings and washers for deformation orâ thread damage.
- Slow fill/reduced flow: Extended fill time âŁor low⣠flow rate-flush âhose,â measure pressureand check for kinks or internal collapse.
- Intermittent pressure/whistling: â Sputtering sounds or pressure âfluctuation-indicates debris, partial valve openingor hose lumen restriction.
- No external signs âbut poor performance: Remove hose and run supply into â¤a bucket to isolate washer valve vs. hose issues.
| Item | Description |
|---|---|
| Length | 4 feet (per hose in the 2-pack) |
| Construction | Inner waterway withâ braided reinforcement and â˘polymer exterior coating |
| Typical supply pressure | Approximately 40-60 psi for normal household operation; deviations can indicateâ supply or valve issues |
Compatibility Matrix, Replacement Considerations, Step-by-Step Installation Proceduresandâ Post-Installation âTroubleshooting
The WX14X10005 GE Washing 4′ Polymer Coated Water Inlet Fill Hose 2 Pack â˘functions as the water supply connection âbetween the household shutoff and the washing machine inlet valve. This style of hose typically combines a flexible âinner âhose (often braided for pressure resistance) with a polymer-coated outer jacket⣠to resist abrasion and corrosion where the hose contacts the appliance cabinet. For compatibility and⣠replacement decisions,â verify the washer inlet thread and orientation against the hose ends (most âresidential washers use a 3/4″ garden-hose threaded inlet), confirm the required length (4′) provides slack â˘without kinkingand inspect the sealing washer âtype and inner diameter to match flow requirements. If a âŁmodel-specific OEM part number â¤is required, cross-reference WX14X10005 â¤with â˘the machine’s parts list âor model compatibility chart before installation rather than assuming universal fit.
Installation and commissioning⣠areâ straightforward â¤but require attention to sealing â¤and routing to avoid post-installation leakage⢠or flow restriction: isolate the water supply, relieve residual pressure, swap the old hose while retaining or replacing the rubber sealing washers, hand-thread âboth fittings⤠to avoid cross-threading â¤then tightenâ to a firm snug⣠with a wrench (avoid over-tightening), â˘and check for leaks under full supply pressure. Common issues after installation include smallâ drips at the threadedâ fittings (usually cured by reseating âor â˘replacing the sealing washer), reduced fill â˘rate â¤causedâ by kinks or internal collapse, âŁand intermittent leaks from a damaged hose jacket; if a leak persists after verifying fittings and âŁwashers, the hose or the inlet valve should be inspected and replaced as necessary. The checklist â˘below and⢠the quick technical reference âtable can be used during selection and troubleshooting.
- Pre-install checks: verify thread size, âsealing washer conditionand⣠hose âlength/route.
- Installation steps: shut off supply, depressurize, hand-thread, wrench-snug,â test under âpressure.
- Troubleshooting symptoms: drips at fittings, âslow fill, visible bulging or â˘abrasion on jacket.
| Item | Description |
|---|---|
| Length | 4 feet (sufficient for most standard washerâ placements; confirm routing) |
| Connection | Standard 3/4″ garden-hose thread (verify against âappliance inlet) |
| Material | Polymer-coated outer jacket over⤠a flexible inner hose (abrasion and âcorrosion resistance) |
Q&A
Will this WX14X10005 4′ polymer-coated inlet hose fit â˘my washing machine?
Most modern washing⣠machines (including many GE models) use the standard 3/4âinch female appliance inletâ thread and will accept a 4′ inlet hose. âTo be sure this hose will âfit yourâ machine, confirm your washer uses⣠a 3/4″ female inlet, verify that 4 feet of hose length is sufficient âfor â¤your installationand crossâcheck your machine’s parts list or owner’s manual for the WX14X10005 part number if you want an exact OEM match.
what size and type of connectors âdoes⤠this hose⤠use?
The hose uses standard â3/4âinch female swivel⢠nuts (standard appliance â˘inlet thread) on each end designed⢠to mate with typical washing machine inlet valvesâ and household âŁwater shutoff valves. It also requiresâ a 3/4″ rubber âsealing washer at each end to make a watertight connection.
How âdo I install the 4′ polymerâcoated inlet hose?
Turn off the water supply and run âthe washer to relieve pressure, then disconnect theâ old hoses. Inspect⢠the threaded inlet and the shutoff valve for debris. Fit a new rubber washer â˘into each hose nut if not alreadyâ installed, handâstart the hose nut⤠onto the inlet, then handâtighten. Finish with a firm quarterâturn to halfâturn with pliers if âneeded-do not overtighten. Open the shutoff valve, check for⤠leaks at both endsand retighten slightly if a small leak âappears.
what does â”polymer coated” mean âand âwhat are⤠the benefits?
“Polymer coated” indicates an⣠outer protective polymer jacket over the inner waterâcarrying tube (which mayâ be reinforced). The coating â¤resists abrasion, corrosion and scuffing, âhelpsâ prevent kinksand improves âdurability and appearance compared with uncoated rubber hoses.
Can I use both hoses for hot and cold waterand are they interchangeable?
Yes. The two hoses in the 2âpack are intended forâ the hot and cold inlets and are generally interchangeable. Ifâ the hoses are colorâcoded or labeled, use the appropriate one for theâ hotâ (red) and cold (blue) valves, âŁbut functionally either hose⢠will work on either â¤inlet.
What water pressure and temperature⢠can these hoses handleand how frequently enoughâ should I replace them?
These hoses are made for normal household water pressure âand temperatures used for laundry.â If⢠you have unusually high inlet pressure â(for example consistently aboveâ 80-100â psi),⢠install⣠a pressure regulator or consult⣠product specifications. As a practical safety guideline, inspect â¤hoses periodically and replace them at the first sign of âŁwear, âleaks, bulgingorâ every 3-5 â˘years âas preventive maintenance.
Do these hoses comeâ with sealing washersand⤠can I⢠reuse the â˘old ones?
Many replacement inlet âŁhoses⣠include new rubber sealing washers preinstalled or includedâ in the⤠package; if not, use new 3/4″ flat rubber washers.It’s bestâ practice to replace old washers rather than reuse them to ensure a reliable, leakâfree⣠seal.
Is this an OEM GE âpart and can I use âthese hoses on other brands?
WX14X10005 is the identifying part number âŁassociated with⤠GE inlet hoses. If âthe listing identifies the part number and GE branding, it is an OEM GE replacement. Because the hose uses the standard 3/4″ appliance fittings, it is âalso compatible with many other brands and models that use â¤the same standard inlets-just verify threadâ size and length before installing.
The â˘Way Forward
The WX14X10005 GEâ Washing 4’â Polymerâ Coated Water Inlet Fill Hose 2 Pack serves a straightforward but critical role in household laundry appliances: it delivers and âcontrols the incoming water supply to theâ washer while its polymer coating and construction reduce the risk of abrasion, corrosion and premature failure. As a purpose-built replacement part available in a convenient two-pack, it helps maintain consistent water flow, minimize âleak-related damageand support reliable machine performance over time.
Routine inspection and accurate diagnosis of inlet-hose condition are critically important to avoid unexpected leaks â˘or operational issues. Signs of bulging, cracking, mineral⣠buildup âor intermittent filling should prompt timely replacement with the correct part number and properâ connections. When in doubt, follow manufacturer guidance orâ consultâ a qualified technician; ensuring correct installation and safe shutoff of power and water âduringâ replacement helps protect the appliance âand the household from water damage⢠while preserving long-term functionality.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
