241850615 Frigidaire Ice Maker Fill tube Assembly is a service replacement component used in automatic ice-making systems; it is a molded fluid-transfer assembly that routes metered water from the refrigerator’s water inlet to the ice maker’s fill cup or mold. The assembly typically comprises a rigid thermoplastic tube, sealing grommet(s) and mounting features that position and seal the water passage through the freezer liner or cabinetand in some designs includes insulation or a small heater element to reduce the risk of freeze-up in the tube.
Inside the appliance, the fill tube assembly interfaces directly with the water inlet valve, the ice maker module (fill switch and mold)and the freezer surroundings maintained by the evaporator.Its primary function is to deliver a controlled volume of potable water to the ice mold while maintaining a watertight seal where the tube penetrates the cabinet. Because it spans the cold zone of the freezer, the fill tube is subject to thermal stresses, condensation and potential ice blockage; it therefore interacts indirectly with defrosting and airflow patterns and must maintain a secure mechanical and hydraulic connection to prevent leaks or under/over fills that impair ice quality and appliance reliability.
This article will describe the 241850615 fill tube’s functional design and typical installation locations, outline model-compatibility considerations and identifying OEM versus aftermarket optionsand list common failure symptoms such as leaks, inconsistent fill volumesand frozen or blocked tubes. It will provide a technician-oriented troubleshooting workflow-visual inspection, pressure and flow checks, detection of freeze-upsand isolation tests of the inlet valve-plus practical replacement considerations including access and removal procedures, sealing and alignment best practicesand verification steps to confirm correct operation after service. Safety and basic preparatory steps (power and water isolation,sanitization of the water system) will also be covered to support a proper and reliable repair.
Table of Contents
- Function and role of the Ice Maker Fill Tube Assembly in Ice Production and Water Delivery
- How the 241850615 Frigidaire Ice Maker Fill Tube Assembly Operates and interfaces with Refrigerator Water and Control systems
- Common Failure Symptoms and Diagnostic Indicators of a Defective fill Tube Assembly
- Compatibility, Replacement Considerations, Installation Procedures and Troubleshooting for the 241850615 Frigidaire Ice Maker Fill tube Assembly
- Q&A
- Insights and Conclusions
Function and role of the Ice Maker Fill Tube Assembly in Ice production and Water Delivery
241850615 Frigidaire Ice Maker Fill Tube Assembly is the molded conduit that delivers metered water from the refrigerator water inlet/valve directly into the ice maker mold. Its primary function is to provide a leak-free, correctly positioned path so the ice maker’s fill mechanism can deposit the precise volume of water into each cavity; misalignment, cracksor blockages in the tube change fill volume or cause leaks. The assembly mounts to the ice maker housing and seals against the fill boss or cupand it must match the valve outlet and ice maker inlet geometry on the appliance to maintain proper flow characteristics and prevent siphoning or backflow into the cabinet area.
- Common failure symptoms: no ice,underfilled or overfilled trays,visible leaks at the joint,or frost buildup indicating a cracked or disconnected tube.
- Rapid checks: verify water supply pressure, inspect tube for cracks or kinks, confirm secure seating at both the valve and ice makerand look for ice or scale blockage inside the tube.
- Replacement guidance: confirm OEM part number and mounting orientation; small differences in length or bend angle affect fit and fill accuracy.
Technicians should treat the fill tube as a flow-control component whose geometry and sealing surfaces determine delivery behavior rather than as a simple hose. when diagnosing, measure actual fill time or volume during one ice cycle and compare to manufacturer specifications to separate valve issues from tubing problems. In practice, swapping in the correct replacement assembly restores predictable fill behavior if fittings and valves are intact; if leaks persist after replacement, inspect the valve seat and mounting tabs for deformation. For model compatibility,always cross-reference the appliance model and serial group to ensure the replacement assembly aligns with the ice maker mounting points and connector type.
| Item | Description |
|---|---|
| Function | Directs and seals water flow from inlet valve to ice mold to achieve correct fill volume |
| Typical material | Rigid or semi-rigid plastic with optional insulating sleeve |
| Common failure modes | Cracks, disconnection, internal blockage, incorrect fit causing leakage or improper fill |
How the 241850615 Frigidaire Ice Maker Fill Tube Assembly Operates and Interfaces with Refrigerator Water and Control Systems
The 241850615 Frigidaire Ice Maker Fill Tube Assembly is a molded plastic conduit that delivers pressurized household water from the refrigerator’s inlet valve to the ice-maker fill cup or mold. Mechanically, the fill tube provides a sealed path and a controlled discharge orifice; the ice maker control module energizes the refrigerator water inlet solenoid valve, which pressurizes the line and forces water through the fill tube for a measured duration. the assembly typically interfaces to the valve or quick-connect tubing with a 1/4″ push-fit or barbed connection and mounts to the evaporator housing so the outlet aligns precisely over the mold; improper alignment,degraded seals,or a tube that has become brittle can cause underfill,overfill,or leakage.
- Common symptoms: reduced volume in ice cubes,continuous dripping,or no fill (can indicate frozen tube,clogged passage,or faulty valve).
- Operational constraints: freeze-back of the tube near the evaporator if not properly insulated or routed; requires adequate inlet water pressure (~20-60 psi typical) for repeatable fills.
- Testing/repair context: verify valve activation with a multimeter or 120/240 VAC (model dependent),measure fill duration and pressure,and inspect physical seating and O-rings during replacement.
| Item | Description |
|---|---|
| Connection size | Typically 1/4″ push-fit or barbed to match refrigerator inlet tubing |
| Material | Rigid molded plastic (resistant to freezer temperatures; subject to embrittlement over long service) |
| Failure modes | Freeze blockage, cracks/leaks at joints, misalignment over mold, or internal clogging from mineral deposits |
Compatibility depends on the refrigerator model and the way the original fill tube routes across the evaporator; the assembly is intended to match the OEM mounting points and outlet orientation so the ice maker’s control timing yields the correct volume. In practical repair scenarios, technicians should confirm water inlet valve operation and line pressure before replacing the fill tube-replacing the tube alone will not resolve a non-energized valve or an electronic control failure. During installation, ensure the tube is free of kinks, secured to the mounting bossesand that any retention clips or foam insulation are reinstalled to prevent ice buildup and maintain consistent fill performance.
Common Failure Symptoms and Diagnostic Indicators of a Defective Fill Tube Assembly
The 241850615 Frigidaire Ice Maker Fill Tube Assembly channels metered water from the fill valve to the ice mold and provides a sealed path that minimizes conductive heat transfer and prevents ice build-up along the bore. Proper function requires correct alignment with the ice maker inlet, intact fittings at both ends, and an unobstructed internal diameter; failures typically arise from mineral scale accumulation, physical crackingor loss of seal at the connection points, each of which alters fill volume and timing. as an OEM-style replacement, compatibility depends on matching the ice maker’s mounting and inlet geometry-installing an incorrectly sized tube can introduce strain on the valve, cause misalignment of the fill portor create a path for water to bypass the mold.
Visual and operational diagnostics focus on the symptoms produced during the dispense/fill cycle and on direct inspection of the tube and fittings. Technicians should compare observed fill duration and cube size to expected behaviour for the model, watch for visible leaks or frost inside the tubeand verify that the tube remains free of scale or ice bridges; these checks help distinguish tube-related faults from fill valve, water-supplyor control-board issues. Practical examples include an or else-functional fill valve that cycles without producing ice (consistent with a clogged or frozen tube) and persistent water pooling in the freezer after a fill cycle (consistent with a split or lose connection).
- No ice production while the fill valve actuates – suggests internal blockage or freeze-up
- Underfilled or hollow cubes and extended fill times - indicates partial occlusion or low flow through the tube
- Water pooling in the freezer or around the ice bin – points to a cracked tube or failed connection
- Intermittent fills, gurglingor air in the line – can indicate loose fittings or pressure/venting problems
- Visible frost or ice inside the tube – evidence of inadequate insulation, freeze-upor reversed drainage
| Item | description |
|---|---|
| Typical symptom | No fill, slow fill, overfill, or leaks observed during ice-maker cycles |
| Common root causes | Scale buildup, mechanical damage to the tube, improper mating to inletor freeze blockage |
| Quick diagnostic checks | Inspect tube for cracks/frost, observe fill valve operation, measure fill duration, confirm outlet alignment |
Compatibility, Replacement Considerations, Installation Procedures and Troubleshooting for the 241850615 Frigidaire Ice Maker Fill Tube Assembly
The 241850615 Frigidaire Ice Maker Fill Tube Assembly is the molded plastic or flexible conduit that carries metered water from the refrigerator inlet valve to the ice maker mold. Its primary function is to deliver a controlled volume of water for each harvest cycle while resisting freezing inside the freezer cavity; some service variants include a heated sheath or integration points for a defrost trace to prevent internal icing. Verify compatibility by matching the inlet fitting diameter, retention clip locations, overall tube length and any required heater connection to the ice maker assembly and freezer liner – physical fit and mating geometry are more critically important than brand name alone. Replacement should use an assembly with identical connection style (barbed,push-fit,or threaded) and the same heater/insulation characteristics when the original part was specified to resist freeze-up in low-temperature compartments.
- No fill or underfill: check for a clogged or crushed tube, low inlet water pressureor a partially failing inlet valve.
- Continuous fill: inspect the valve and the ice maker fill cup alignment; a stuck valve diaphragm or incorrect control signal can cause overfill.
- Ice buildup on or inside the tube: indicates loss of heater function or routing that allows static cold pockets; install a heated tube variant if specified by model.
- Leaks at connections: confirm proper seating, replacement of any quick‑connect fittingsand secure retention clips to prevent movement during door cycles.
Installation procedure: isolate water and power, remove the ice bin and any interior trim to access the tube path, disengage retention clipsand disconnect the tube from the inlet valve and the ice maker using the correct release technique for the connector type. Route the replacement so there are no sharp bends or kinks, restore clips at the original attachment points, reconnect the water and run a controlled fill test while observing for proper volume, cycle timingand absence of leaks.Troubleshooting commonly requires measuring static water pressure at the valve, verifying valve actuation with an applied 120/240 V or specified control voltageand inspecting for internal obstructions or freezing within the tube; if the tube repeatedly freezes, replace it with the heater-equipped variant and confirm thermostat/temperature settings in the freezer compartment.
| Item | Description |
|---|---|
| part number | 241850615 - OEM fill tube assembly for select Frigidaire models |
| Material | Molded polymer tubing; some variants include an electric heat trace and thermal insulation |
| Connections | Inlet valve end and ice maker end – barbed or push-fit; verify clip retention and sealing method |
| Common failure modes | Blockage from mineral deposit, mechanical compression/kinking, heater failure (if equipped)or connector wear |
Q&A
What is the 241850615 Frigidaire ice Maker Fill Tube Assembly and what does it do?
The 241850615 is the plastic fill tube assembly that routes water from the refrigerator’s water inlet/valve to the ice maker mold. It directs the measured water shot into each ice tray cavity so the ice maker can produce cubes. The part is typically mounted at the back/top of the freezer compartment and mates to the ice maker and the water inlet path.
What are common signs the fill tube is failing or blocked?
common symptoms include: little or no water entering the ice mold, ice cubes that are small or misshapen, visible leaks or water pooling in the freezer, a cracked or brittle tube visible behind the back panelor a tube frozen shut (ice blockage) that prevents fills. Inspecting the tube visually and checking for frozen obstruction often confirms the issue.
Is the 241850615 fill tube compatible with my Frigidaire or other-brand refrigerator?
241850615 is an OEM Frigidaire part used on a range of Frigidaire/frigidaire Gallery/Frigidaire Electrolux (and some kenmore) models, but compatibility varies by model. Always verify by entering your refrigerator’s model number on Frigidaire’s parts site or the parts retailer’s compatibility checker before ordering.
Can I replace the fill tube myselfand what safety steps should I take?
Yes, a competent DIYer can usually replace it. Critically important safety steps: unplug the refrigerator (or switch off the breaker) and shut off the water supply before starting. Typical steps are removing the freezer back panel, detaching the old tube from clamps or fasteners, installing the new tube and clamps, restoring power and water, and testing for proper fills and leaks. If you’re uncomfortable with electrical or plumbing work, hire a qualified technician.
What tools and materials are required to replace the fill tube?
Common tools: Phillips and flat screwdrivers, nut driver or socket set (usually 1/4″-5/16″), pliersand possibly a Torx driver depending on model. You may also want a hair dryer or warm cloth to thaw a frozen tube during removal, and a towel to catch water. Replacement clamps or small zip-ties and the correct OEM tube are recommended for a secure fit.
How can I prevent the fill tube from freezing or clogging again?
Preventative steps: ensure the fill tube is routed away from the evaporator airflow and properly seated in its clips, use an insulating sleeve if available, keep freezer temperature within recommended range, maintain good door sealsand periodically check for ice buildup behind panels. If the water supply pressure is to high or the tube is cracked, replace it-leaks and siphoning can cause re-freezing.
Will replacing the fill tube definitely fix an ice maker that won’t fill?
Replacing the fill tube will fix problems caused by a cracked, disconnectedor frozen tube.However, if the cause is a faulty water inlet valve, clogged water line, a bad ice maker fill solenoid/ice maker moduleor an upstream shut-off valve or filter issue, replacing just the tube won’t resolve it. Troubleshoot the water valve and supply if replacing the tube doesn’t restore proper fills.
How much does the 241850615 fill tube cost and should I expect additional repair charges?
The OEM fill tube itself is inexpensive-typically in the low tens of dollars (often around $10-$35). If you hire a technician, labor will add to the cost; typical service calls and labor for a straightforward replacement often range from about $80 to $150 depending on region and shop rates. If other components (water valve, ice maker) need replacement, total cost will be higher.
Insights and Conclusions
The 241850615 Frigidaire ice maker fill tube assembly plays a focused but essential role in refrigerator operation by delivering the precise amount of water from the household supply to the ice maker at the correct point in the fill cycle. Properly functioning fill tubes help ensure consistent ice production, reduce the risk of leaks or water intrusion into the freezer compartmentand contribute to overall appliance efficiency and ice quality. As this part is designed to interface with Frigidaire ice-making systems, correct fit and material compatibility are critically important for reliable long-term performance.
Accurate diagnosis of symptoms such as reduced or absent ice production,visible leaks,or frost buildup around the fill area is important before deciding on replacement. Visual inspection, basic functional checks of the water supply and ice maker cycleand understanding common failure modes can prevent unneeded parts changes. When the fill tube is determined to be the source of the problem, replacing it with the proper assembly restores intended operation, helps avoid secondary damage from water exposureand supports continued appliance reliability.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
