241850615 â˘Frigidaire⣠Ice Maker fill Tube⣠Assemblyâ is a molded fluid conveyance component designed âŁtoo deliver potable water from the ârefrigerator’sâ water inlet to theâ ice maker mold. As aâ fill tube assembly, it typically consists of a â¤rigid⢠or semi-rigid plastic tube, mounting features and a sealing grommet âor flange; its primary purpose âis â¤to provide âa controlled, sealed path for water into theâ iceâ tray while passing through the â¤freezer âwallâ or cabinet partition.
Within⢠the appliance,the â¤fill tube interfaces directly with the water inlet valve,the ice makerâ module âŁ(or ice âmold),and the cabinetâ sealing system. It must maintain a⢠proper orientation and seal âto prevent leaks, avoidâ air intrusion,â andâ minimize heat âŁtransfer that could causeâ the tube to freeze or the mold to overfill. âTechnically, the component is part â¤of the â¤refrigerator’s waterâ delivery subsystem and affects fill âtiming, fill volumeand reliability; its performance âcan be influenced by water pressure, tube routing, insulationâ at the wall âpenetrationand the condition of â˘the âmating grommet andâ valve.
In this⢠article readers will find a focused technical overview of the part’s function âand typical applications, âŁguidance on compatibility andâ identification, common failureâ symptoms (for example no-fill, overfill,⣠slow fill, freezing or leaks)and diagnostic checks âa technician or owner can perform. the piece will⣠also â¤cover troubleshooting priorities-visual inspection,â verification of water supply and pressure, examination of mating components-and practical replacement⤠considerations such as sealing, routingand â˘safety steps (power and water isolation) to⢠ensureâ correct⣠installation and reliable operation.
Table of Contents
- Function âand Role âŁof the Ice Maker â˘Fill Tubeâ in Water Delivery and Freeze⤠Cycle
- How âthe â˘241850615 Frigidaire Ice Maker Fill Tube Assembly Works Inside the Appliance
- Common Failure Symptoms and Diagnostic Indicators of Fill Tube Blockage,â Freeze âor Leak
- Replacement Considerations, âCompatibility â˘with âAppliance Models, âŁand Installation Procedures
- Q&A
- In⤠Retrospect
Functionâ andâ Role of âthe⤠Ice maker Fill Tube in Water Delivery âand freeze Cycle
The 241850615 Frigidaire Ice Maker Fill Tube âŁAssembly⤠is⣠a molded plastic conduit that routes potable water from theâ refrigerator’s water âŁinlet valve directly âintoâ the ice mold during the fill portion âof the cycle. âŁWhen the ice maker’s control opens the inlet solenoid, water flows through this tube; the tube’s internal diameter, length and outlet geometry determine fill rate âand droplet âdelivery, â˘which in turn âcontrol the cube size and the fill duration requiredâ before the freeze cycle begins. The âassembly also incorporates mounting features and a sealing interface to â¤the valveâ and ice maker body to prevent âleaks and to inhibitâ backflow⢠or siphoning; therefore a correct physical match â˘to the valve portâ and ice maker housing is required for reliable operation and to avoid over- or⣠under-filling âissues.
- Common failure âmodes:â mineral âclogging (small cubes/slow fill), cracks or splits (leaks and â˘frost buildup),⢠and âmisalignment (overfilling or water â˘spilling into evaporator).
- Compatibility ânotes: designed⣠as an âŁOEM Frigidaire fit; mismatched tubes may require different seals âor trimming toâ achieve proper length and orientation.
- Diagnostic tips: observe a timed âfill,⤠inspect for iceâ inside âŁthe tubeand check seals at the valve connection.
| Item | Description |
|---|---|
| Material | Molded polymer (typical PVC/nylon blend) resistant to cold and potable water âchemicals |
| Inner diameter | Small â¤bore sized to meter water for the ice maker; âaffects⤠fill time and â¤cube âsize |
| Primary function | Deliver measured water to the ice mold and âŁprevent backflow orâ uncontrolled drainage |
During service or replacement,⣠verify that the âtubeâ seats fully âat the valve âand into⤠the ice maker housing and that any anti-siphon bends or insulating⤠sleeves are retained; improper⣠seating or âa tube that protrudes into the mold can create freezing âobstructionsâ or premature ice formation â¤inside the âtube. For practical troubleshooting, remove â¤andâ visually inspect the tube for mineral scale or ice â¤blockages and perform âŁa timed⣠volume check while the valve is actuated; replacing the 241850615⣠Frigidaire Ice Maker Fill Tube â˘Assembly is a common âcorrective action â¤when flow restrictions or âphysical damage âare â˘found, but ensure matching port⤠dimensions âand mounting points to restore correct operation.
How the 241850615â Frigidaireâ Ice â˘Maker Fill Tube Assembly Works⣠Inside the Appliance
241850615 âFrigidaire⣠Ice Maker Fill Tube Assembly is âthe moldedâ conduit that channels metered household âwater from the refrigerator’s inlet valve into â¤the ice mold during the ice-maker’s fill cycle. âŁIt mounts through the freezer liner,typically sealed with a rubber grommet âŁand retained by⤠a clip,and delivers water to the fill cup or nozzle⢠positioned⤠over the⢠mold. During a normal fill â˘event the ice-maker control opens the water âvalve for a timed interval and the fill tube must âprovide âŁan unobstructed, properly oriented flow path; misalignment, âcracks, mineral buildup,⤠or aâ poorly seated grommet will cause â˘underfill, overfill,⤠or leaking into âŁthe freezer cavity. The assembly’sâ geometry and sealing surfaces are engineered to fit⢠a range of Frigidaire âice-maker modules, so⢠replacement should match the original part number to ensure correct fit and function.
The fill tube’s âbehavior in service is âmechanical and hydraulic:â it is passive and ârelies on âŁthe inlet⤠valve timing â¤and water pressure âto meter volume. Commonâ failure â¤modes are physical damage (cracks or âsplits), internal blockage fromâ mineral scale or iceand âloss ofâ the sealing â¤grommet â˘that prevents backflow or freezer condensation from⢠entering the cabinet. â˘For diagnostics,inspect the tube for visible damage,check that the grommet formsâ a⣠continuous seal âŁin the liner,and confirm the water⢠valve energizes only for the âintended fill duration. If freezing within the tube is suspected, âwarming the âtube and checking⢠the inlet pressure and valve operation⣠will âŁdistinguishâ obstruction from control faults; brittle or deformed tubes should be replaced rather than patched to restore reliable⣠operation.
- Key features: molded water channel, grommet seal, retentionâ clip/nozzle âinterface.
- Symptoms of âŁfailure: no ice production, partial fills, continuous water floworâ water pooling in the freezer.
- Troubleshooting steps: â¤inspect tube/grommet,clear mineral deposits,verify valve actuation and fill timing,replace if â¤cracked or deformed.
| Item | Description |
|---|---|
| Function | Directs timed water⤠flowâ from â˘inlet âvalve to ice mold |
| Mounting | Inserted through freezer liner âandâ sealed with⣠a rubber⣠grommet |
| Common â˘issues | Cracks, blockages, grommet failure⣠causing leaks or misfills |
Common Failure Symptoms and Diagnostic âŁIndicators of Fill Tube âŁBlockage, Freezeâ orâ Leak
The â241850615 frigidaire Ice maker Fill Tube Assembly is âthe⣠molded conduit that delivers metered â¤water⤠from the appliance âwater inlet/solenoid valve to the ice maker fill cup. In normal operation the fill tube provides⣠an âunobstructed, small-diameter path and a sealed connection atâ both âends so âthe ice maker âreceives⤠a⣠repeatable⤠volume â˘of water during each harvestâ cycle. Blockage âcommonly presents⤠as reduced cube size,⢠hollow or misshapen cubesor intermittent⤠fills and â¤is often caused by mineral âscale, trapped debris, a kinked or crushed tubeor âlocalizedâ freezing at the tube âŁinlet were cold air penetrates the line.â leaksâ typically appear at connection points or from hairlineâ cracks in aged thermoplastic material and produce visible pooling or iceâ accumulation inside the freezer compartment;⢠compatibility with a⢠particular Frigidaire ice maker requires a correct mating geometry⢠at the valve âŁand fill cup interfaces, so symptoms can â˘differ if the assembly isâ misaligned or â˘substituted with an⣠incorrect part.
Diagnostic â¤indicators isolate whether the fault âis a restriction, an ice blockage, âor a leak by correlating fillâ volume, soundand⤠visual⣠evidence. A technicianâ can quantify the problem by observing fill âtiming and volume during a â¤fill â˘cycle (short orâ stopped⣠fills pointâ to obstruction; continuous trickle or overfill âŁpoints to valve/float issues), probing the tube for frost or soft spotsand inspecting fittings for cracks or loose clamps. Common, observable symptoms and straightforward checks includeâ listening for the⤠solenoid⢠while measuring fill duration, warming a suspected frozen section⤠briefly to restore flowand disconnecting the tube at the ice âmaker to verify full âflow⣠from âŁthe â¤valve; these actions help determine whether to clean, heat, replace the tubeor address⣠the valve or water â˘supply upstream.
- Reduced or partial fills – smaller orâ hollow cubes â¤indicating partial blockage or kinking.
- Intermittent fills or no fills â¤- possibly â¤frozen section or debrisâ obstructing flow.
- Continuous flow⢠or overfill⠖ often a valve or fill-cup seating issue rather⢠than the tube itself.
- Visible moisture,⢠frostor pooling – evidence of âa leak or freeze-related rupture at a joint.
| Item | Description |
|---|---|
| Reduced fill volume | Likely partial blockage from scale/debris or a kinked âtube; inspect and clear or replace. |
| Frost on tube | Indicates cold-air intrusion and localizedâ freezing; warm and âŁinsulate the section or replace if damaged. |
| Visible leak at connection | Loose or âcracked fitting; tighten â¤clamp or replaceâ tube and checkâ mating⣠surfaces. |
Replacement Considerations,⢠Compatibility with âAppliance â˘Modelsand installation Procedures
The â241850615 frigidaireâ Ice Makerâ Fill Tube Assembly⢠routes water from the refrigerator’s inlet valve to⤠the ice maker âmold andâ acts as the controlled âŁconduit that meters each fill cycle. The assembly is typically a molded thermoplastic tube with a âŁshaped outlet⣠andâ mounting flange âthat must âalign with â¤the iceâ maker inlet port andâ freezer liner; incorrect orientation or âdamaged seals will alter fill volume, cause â˘leaksor permit air intrusion that produces spongy or partial cubes. Verify fit by matching âthe OEMâ part⣠number andâ the âphysical interfaceâ (mounting âtabs and inlet diameter) to the âappliance’s service diagram before â˘replacing the assembly, as the same basic fill-tubeâ design is used â¤acrossâ several Frigidaire-derivedâ platforms but can differ â¤in flange geometry⣠and⣠connector â˘style.
Replacement âand⢠installation require isolating water and power,removing theâ ice maker â¤or â¤its â¤shroud â˘to gain⢠access,and confirming the mating surfaces âare â˘clean and free of iceâ or debris. during installation, seat âthe âŁfill⣠tube evenly against the liner or retainer clip, secure any retaining fastenersand restore âŁwaterâ pressure âbriefly while observing the joint for leaks; perform a test fill cycle and allow â¤several freeze/melt âcycles to confirmâ correct volume⤠and that âno frosting on the âexterior of the tube indicates âŁpoor insulation or exposureâ to the evaporator.Typical inspection âpoints and symptoms thatâ indicate⣠replacement include:
- Visible âcracks,splits,or brittleness in the tube material âor flange area.
- Frost buildup or ice⢠bridging⤠at⢠the tube exit, indicating poor sealing or misrouting.
- Slow or⣠incomplete fills despite correct water â¤pressure,suggesting blockage or partial collapse.
- Water pooling on the freezer floor or under âthe âice⢠makerâ during/after âfill cycles.
| Item | Description |
|---|---|
| 241850615 | OEM fill⣠tube for select âŁFrigidaire ice makers – molded thermoplastic conduit with â¤factory-specific âflange âŁand retaining features |
| Common failureâ modes | Cracking, freeze damage, internal obstruction, seal wear |
| service notes | Confirm flange geometry and inlet connection before purchase; purge air after reconnection and verify fill volume over several cycles |
Q&A
What is part⣠241850615 (Frigidaire âŁice maker fill tube assembly)â and what does it do?
241850615 is the⢠fill tube assembly usedâ on certain Frigidaire refrigerators.The fill tube carries pressurized water from the refrigerator’sâ water supply line to the ice maker fill â˘valve/nozzle so the ice maker âcan fill the ice mold. Itâ also provides a sealed connection through âŁthe âfreezer evaporator compartment andâ often â¤includes a rubber grommet or seal where it passes the cabinet liner.
What symptoms indicate the fill âtube⤠assembly might be⤠failing or damaged?
Common symptoms â˘include visible⣠water leaks in the⣠freezer, water pooling under or around the ice maker, the ice maker not â˘filling or⢠only partiallyâ filling, water spraying⢠or dripping from the fill âareaor a fill tube âthat has frozen solid and stopped delivering water. Physical inspection may reveal cracks, brittle plastic, â˘or a missing/damaged seal.
How do I check whether 241850615 is compatible with my refrigerator model?
Check the⢠refrigerator model number⢠(usually on a⣠sticker inside the fresh⢠food or freezer compartment or on⢠the cabinet wall) and⣠compare it against the part’s compatibility list⣠from Frigidaire or âan authorized partsâ dealer.⣠You can also⤠enter your model number âŁon Frigidaire’s⤠official â˘partsâ lookup or contact customer support to confirm compatibility before purchasing.
Can I replace the fill tube assembly myself,⣠and what are âthe basic steps?
Yes, many technicians and experienced owners can replace it.â Basic steps:â 1) unplug the ârefrigerator⤠and â¤shut off the water supply; 2) remove⢠shelves/ice bucket â¤and take off âŁthe freezer evaporator âcover or âpanels to access the fill tube; 3) disconnect any clips or screws holding the tube and⣠remove it from its grommet; 4) remove the old tube and grommet,install the new tube (ensure the â˘grommet/seal seats properly),and reattach â˘clips/screws; 5) ârestore the evaporator cover,turn the â˘water back â˘on,plug theâ fridge in,and check for leaks while cyclingâ the ice maker.Follow the âmodel-specific service instructionsâ and â˘observeâ electrical and âplumbing safety precautions.
What tools and time should I expect âfor the replacement?
Typical tools: nut driver or socket set (commonâ sizes 1/4″-5/16″),Philips/flat â¤screwdriver,pliers,and possibly Torx âdrivers for âpanel screws. You may also needâ towels or a smallâ container for residual water. âFor an experienced⤠DIYer, the job usually takes â˘30-90 minutes âdepending on access. If you’re unsure, hiring â¤an appliance âŁtechnician is recommended.
How⣠can I â˘tell âif a no-fillâ problem is caused by the fill tube â¤freezing versusâ a bad water inlet valve or frozen water line?
To diagnose: listen for the ice maker’s fill cycle and check if the inlet valve âclicks; if the valve opens but no âŁwater⣠appears,inspect the fill tube âŁfor ice buildup (visible âunder the evaporator cover). Temporarily defrosting theâ tube (shut off water and⢠run⢠a shortâ defrost cycle or use âŁa hair dryer briefly⤠while avoiding electrical parts) can confirm aâ frozenâ tube. If the valve doesn’t actuate or there is no water pressure at the fill tube whenâ the valve is energized, the water inlet valve or supplyâ lineâ is likely âthe⢠problem. A multimeter can âtest valve âŁcoil continuity and âan inline pressure check can âconfirm supply pressure.
Will âŁreplacing⣠the fill tube stop leaks,⢠or do I need to replace other âparts too?
replacing a â˘cracked or damaged â¤tubeâ and its grommet will stop leaks caused by those components, but you should inspect related parts: â¤the â¤rubber seal/grommet, mounting clipsand the connection âto the waterâ inlet valve. If the water inlet valve â˘is leaking or delivering excessive pressureorâ if clamps/seals are âŁdeteriorated, you may need to⤠replace those parts as well. After replacement, carefully check for leaks during the first â˘fill cycle.
Is 241850615 an OEM Frigidaire⢠partand where can âŁI â˘buy it? How much does itâ cost?
Yes-241850615 is soldâ as an âOEM Frigidaire fill tube â˘assembly. You can buy it from Frigidaire’s parts website, authorized appliance parts dealers, âor reputable online retailers. Prices vary by seller and region but commonly range from approximately $15 â˘to â˘$60 for theâ partâ alone.⣠If you’re unsure, buy from a⢠seller that âŁaccepts returns and verify compatibility with â˘your model number.
In Retrospect
The 241850615â Frigidaire Ice Maker Fill Tube Assembly⢠plays a âcentral ârole in delivering controlled water⤠flow from âŁthe household supply to the iceâ maker mold. As aâ precision component of the â˘refrigerator’s ice-making system, it ensures proper fill volume, prevents âwater leaksand helps âmaintain âconsistent ice⣠production and quality. âWhen functioningâ correctly, âthe fill⢠tubeâ contributes to efficient appliance performance and minimizes the risk of freeze-relatedâ blockages âŁor water damage.
Accurate diagnosis⢠is⤠essential before replacing âthe fill tube: â¤symptoms â¤such as no ice, underfilled ice trays, â˘visible leaks, âunusual ice shapesorâ intermittent water flow can indicate a damaged or obstructed âtube, but may also stem from related components like the âŁinlet valve⣠or âwater supply line. Evaluating the entire⤠water-delivery âpath, verifying proper water pressureand identifying⣠signs of physical damage or blockage willâ help determineâ whether replacement of the 241850615 assembly is necessary.
When⤠replacement is warranted, using âŁthe⣠correct part â¤and following proper installation âand alignment â˘practices restores âreliable operation and reduces the likelihood of subsequentâ leaks or malfunctions. For complex diagnoses, uncertain installation stepsor â¤if âthe refrigeratorâ is â˘under warranty, consultation⢠with a qualified service â¤technician is recommended. Regular âinspection and timely⤠replacement of⤠worn components support long-term âperformance and protect against avoidable ice-making failures.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
