137392700 Frigidaire Dryer Heating Element Assembly âisâ an electric resistance heating component designed for use in frigidaireâ electric clothesâ dryers. The assembly typically consists⣠of one⤠or more resistive heating coils mounted in a âmetal housing with electrical terminals and mountingâ features; â¤some assemblies also integrate or âinterface with thermal⤠cutouts, âhighâlimit thermostats or terminal blocks depending on the⢠dryer model. As⣠a discrete replaceable unit, it provides âthe primary source of âheat used during the dry â˘cycle.
Within the⤠appliance,â the âheating element assembly converts electrical energy into heat and forms a key â¤partâ of â¤the dryer’s heating âsubsystem,⤠interacting directly with â¤the â¤line⤠power supply, the âtimer/control⢠electronics, the cycling and highâlimit thermostats, the thermal fuse, theâ blower and the drum/airflow path. properâ operation â˘depends not only onâ the⤠integrity of⣠the âresistive coils but also on adequate airflow across âthe element for cooling and heat distribution; â¤restricted venting or a failed thermostat can cause overheating, premature elementâ failureor safety⣠device interruptions. The element therefore plays a⢠central role⣠inâ temperature regulation, safety⤠cutoff behavior and overall drying performance.
In this article readers⢠will gain a technical overview of the 137392700 heating element assembly including âits functional principles and â¤how toâ verify âŁcompatibility with specific Frigidaire dryer⣠models. The discussion will âcover common failure symptoms (no heat, reduced heat, tripped thermal fuses, visible damage or shorting), stepâbyâstep troubleshooting techniques (continuity and âinsulationâ checks, verifying associated thermostats and fuses, âand âŁconfirming correct âsupply voltage)and âŁpractical replacement considerations (power⣠isolation, part verification, correct mounting and terminal connections, âand postâreplacement tests includingâ airflow â˘and vent inspection). The⤠focus is on providing⢠technicians,⣠engineers and appliance owners with the information needed to diagnose⢠issues and perform safe, effective repairs⢠or replacements without marketing claimsâ or âunverified performance assertions.
Table of Contents
- Function andâ Roleâ of the âHeating Element assembly âin the Dryer’s Thermal Management⣠System
- How the 137392700 Frigidaire Dryer Heating Element Assembly Works âInside the Appliance: Integration with Thermostats, Thermal Fusesand Airflow
- Common Failure Symptoms⢠and Diagnostic Indicators for Heating Element faults (open/short, overheating, intermittent⢠operation)
- compatibility, Model⤠Fitment, Replacement considerationsandâ StepâbyâStep Installationâ and troubleshooting âŁProcedures
- Q&A
- The Way Forward
Function â¤and Role âofâ the Heating Element Assembly in the Dryer’sâ Thermal Management System
The 137392700 Frigidaire Dryer Heating Element â˘Assembly is the primary resistiveâ heating component in the dryer’s thermal management system.⣠Itâ converts mains electrical energy into heat via â¤nichrome-style resistance coils housed in the heater box and works in concert âwith the timer âorâ control board, cycling â˘thermostats, âand thermal cutoffs to maintain the target drum temperature. in normal â˘operation the âcontrol logic supplies power toâ the element in controlled âŁintervals âwhile âthe exhaust â˘fanâ and drum airflow remove moisture; reduced airflow or obstructed vents âraises internal temperatures and âŁcanâ cause safety devices to open. â˘Technicians verifying this assembly commonly measure continuity and cold resistance across âthe element to confirm âcircuit integrityâ andâ compare observed resistance to the expected â˘range for the dryer’s voltage and wattage rating before proceeding⢠with replacement.
- Common symptoms of⢠element â˘or system issues: no heat (open element), intermittentâ heat (loose connection or â¤failing relay), excessive temperature trips (blocked airflow or failed thermostat).
- Key compatibilityâ and installationâ considerations: matchâ electrical rating (typically âŁ208-240â V), physical⤠mounting and terminal types,â and âŁany⢠integrated safety fuses or housingsâ included with the⣠assembly.
Understanding âtheâ assembly’s â˘role â˘helps isolate faults: âan open coilâ presents as infinite resistance on a multimeter and produces no⢠heat,â while a coil shorted to âchassis will typically blow fuses â¤or trip breakers. Replacement with theâ correct⤠part number preserves the designed⢠thermalâ response-incorrect wattage or mismatched terminals âcan cause under-drying, excessive cyclingor nuisance âtrips âŁof high-limit⣠devices. During service, verify supply âŁvoltage âŁat the element terminals, inspect â˘associated thermostats⣠and thermal cutouts â¤for proper operationand âconfirm exhaust airflow and lint removal to restore âreliable thermal⤠management after installing theâ new⣠137392700 Frigidaire Dryer Heating âElement assembly.
| Item | Description |
|---|---|
| Voltage | Typical household âelectric dryer supply: â208-240 V |
| typical power | Approximately 3,000-5,000 W⣠depending âon model |
| Approximate resistance | Common cold âresistance range:â ~12-20 Ί (varies with element âwattage) |
| Function | Resistive coil assembly that generates heat;â interfaces with thermostats,thermal cutoffs,and control⢠circuitry |
How the 137392700 Frigidaire Dryer Heating Element Assembly Works Inside the⤠Appliance: Integration with Thermostats,Thermal Fuses,and Airflow
The 137392700 Frigidaire Dryer Heatingâ Element Assembly is the resistive coil and âŁsupport frameâ that generates the âŁhot air⢠usedâ in⤠drying cycles; it⢠must work in concert with âŁthe dryer’s thermostats,thermalâ fuse,and the machine’s airflow âpath to maintain safe,consistent temperatures. â˘In most dryer designs â˘theâ element is âŁsupplied with line voltage⢠throughâ a series of control âelements: a cycling (operating) thermostat controlsâ on/offâ duty⣠to regulate set temperature, while a highâlimit thermostat and a thermalâ fuse are placed in series as safety cutouts that open at overâtemperature conditions.For â¤effective replacementâ and troubleshooting verify model âcompatibility, terminal layoutand harness connectionsand use a multimeter to âconfirm âcontinuity of the element âand âthe safety devices-an intact coil â¤withâ an openâ thermal fuse or âtripped highâlimit thermostat willâ still result in no heat being delivered to the drum.
From a functional standpoint the âheating âelement’s behavior is determined by both electrical control and convectiveâ cooling: the cycling thermostat senses exhaust âŁor drum air temperature âand interrupts power to maintain setpoints, whereas the highâlimit and thermal fuseâ interrupt power when air temperatures exceed safe thresholds. Restricted airflow increases⤠runâtimeâ and local temperatures⢠around the coil,⢠accelerating element stress and creating hotspots that can⤠cause coil⣠rupture or nuisance trips of the thermal fuse. âCommon field âtests include visually inspecting âthe element for breaks or sagging, measuring continuity across â¤element⣠terminals and across each thermostat/thermal â¤fuseand restoring proper venting to observe whether cycling behaviorâ returns to normal.
- Noâ heat: element open, âthermal fuse or highâlimit openor wiring fault.
- Intermittent heat⤠or long âcoolâdown intervals: restricted venting or failing cycling⣠thermostat.
- Thermal fuse frequently âblown: persistent âŁoverâtemperature from⤠airflow restrictionâ or shorted element.
- Multimeter checks: continuity on elementâ and closed state of thermostats/fuse⤠when âŁcold.
| Item | Description |
|---|---|
| Heating element | resistive coil assembly âŁthat converts â¤electrical energy into⢠heat. |
| Cycling thermostat | Controls element duty cycle⣠to⤠maintain operating temperature. |
| Highâlimit thermostat | safety cutoff⢠that âopens on excessive temperature but may reset when cool. |
| Thermal fuse | Oneâtime safety device in âthe exhaust path that opens âŁat unsafe temperatures. |
| Airflow/venting | Removes heated air; restrictions âincrease element onâtime and risk of â¤failure. |
Common Failure Symptoms and Diagnostic⢠Indicators for Heating Element faults (open/short, overheating, intermittent operation)
Theâ 137392700 Frigidaire Dryer Heating Element⤠Assembly is⣠the resistive coil âand supportâ structure that converts line voltage⤠into⣠heat for drying cycles. In normal operationâ the element presents a low ohmic load between its two⣠live â˘terminals and is insulated from⢠the cabinet and mounting frame; a discontinuity (open) in⤠the coil âresults in noâ heat,while insulation breakdownâ or contactâ to chassis (short-to-ground) can cause â¤circuit breakers or thermal⤠cutouts to tripâ and may create overheating conditions. physical⢠failure modes⣠includeâ broken coilâ windings, corrosion âat terminal⤠lugsand â¤degraded insulation from repeated thermal cycling; these affect âŁcompatibility only if replacement â˘assemblies⢠differ in terminal layout, mounting flangeor rated wattage, so matching the part â(137392700 Frigidaire âdryer Heating Element â¤Assembly) âŁto âŁthe âŁmodel-specific mounting and electrical ratings is necessary⣠for proper operation.
- No heat: dryer runs âbut âŁdoes not warm -â multimeter shows⤠open circuit â¤(OL) across element âŁterminals.
- Trippingâ breakers or blown thermal fuses:⤠suggests â¤a short to ground or reduced insulation resistance âbetween coil and chassis.
- Overheating or element glowing continuously: indicates failed thermostats or elements with reduced resistance or poor âairflow; check temperature â¤cutouts.
- Intermittentâ heating: often caused by loose terminal connections, âŁbroken internal leadsor intermittent contact in harnesses âŁ- replicate symptomâ while â˘probing.
- Visible damage:⣠distorted coil, burnt insulationor hot spots on the support âframeâ are direct indicators for replacement.
| Item | Description |
|---|---|
| Expected supply | typically 240 VAC across the element terminals in U.S.â single-phase dryers â(verify model supply). |
| Normal⢠resistance (coil) | Lowâ ohms â˘(roughly 5-30 Ί â˘depending âon element design); consult model specifications for exact value. |
| open-circuit indication | Multimeter reads OL or infinite resistance â¤betweenâ element⤠terminals – element is failedâ open. |
| Short-to-ground indication | Continuity or⤠very low resistance âbetween âŁany elementâ terminal and⤠chassis ground – insulation failure âŁpresent. |
For practical diagnostics,â measure element resistance⣠with the⢠dryer disconnected from power, then check forâ continuity to chassis to rule out shorts; âŁif the resistanceâ is in the expected low-ohm range but the⢠dryer still overheats or⤠cycles erratically, âinspect thermostats, high-limit âŁcutoutsand the control relay or timer contacts for intermittent switching. When replacing the unit, use an âassembly that âŁmatches⢠theâ original mounting pattern, terminal âŁspacingand wattage rating-incorrect fit orâ rating⣠can âproduce poor heat distribution, nuisance tripsor premature failure-also âŁverify â˘connector integrity âand strain relief to âreduce recurrence ofâ intermittent⣠faults.
Compatibility,Model âFitment,Replacement Considerations,and StepâbyâStep Installation âand Troubleshooting Procedures
The 137392700 Frigidaire Dryer Heating â¤Element Assembly is a resistive coil housed in a stamped metal enclosure that âŁdirects heated air into theâ drum while isolating the coil from the cabinet. In⢠normal operation the coil converts mains voltageâ into heat andâ works âin concert with the cycling thermostat, highâlimit â¤thermostat and thermal⢠fuse âŁto regulate temperature. Compatibility depends⢠on more thanâ the OEM number: confirm the dryer model/serial tag and verify the⣠mounting⤠bracket orientation, terminal style (spade/blade)and physical envelope âŁof the housing. Some frigidaire/Electrolux variants âŁshare the same element assembly, while others ârequire alternate housings due⣠to differences in blower offset, vent⣠locationor panel access; comparing the new assembly directly to âŁthe removed part prevents â¤misfit and âairflow restrictions that can cause premature failure.
Disconnect power before any service and use a multimeter to verify open âcircuits.⢠Typical installation steps are: removeâ the⢠appropriate accessâ panel, label and detach the âelement wiring, remove mounting fasteners and the old assembly, inspect adjacent thermostats and the thermal fuseâ for damage or âlint âaccumulation, fit the replacement⣠assembly making sure the gasket âŁand⢠airflow path are correct,â reconnect wires to the corresponding terminalsand perform a controlled test run while monitoring drum temperature and cycling. Common⣠failure symptoms and âinitial âŁchecks include:
- No⤠heat – check⢠element continuity and the thermal fuse; replace the fuse only after confirming âthe root âŁcause.
- Intermittent âŁor weak heat – verify cycling thermostat operation and inspect for partial coil shorts or high resistance connections.
- Overheating or tripping high limit -â confirm cycling thermostat placement and that theâ blower is moving sufficient⣠air;⤠checkâ for â¤lint blockage.
- Tripped breaker or blown fuses âon start – lookâ for shortedâ coil âŁstrands contacting the housing or damaged insulation âon terminal wires.
| Item | Description |
|---|---|
| Resistance (typical) | approx.10-30 Ί for⤠common 2-4 kW dryer â˘elements; use this as a diagnostic referenceâ rather than âa specification. |
| Connector âŁtype | Standard 1/4″ spade terminals on many Frigidaire models;⢠verifyâ before finalizing⣠purchase. |
| Mounting⣠considerations | Checkâ bracket orientation and screw locations; incorrect fit can alter airflow and thermostat âsensing. |
Q&A
What is the 137392700 Frigidaire Dryer Heating Elementâ Assembly âand which dryers does it fit?
The â137392700 is a⢠heating element âassembly â¤(the electric heating coil, housing and mounting⢠hardware) used as an⤠OEMâ replacement in many Frigidaire (and some Electrolux/Universal) electric dryers. It is indeed intended⣠for electricâ (not gas) dryer models. â˘To confirm fitment, match the part number to your dryer’s model⢠number âusing the manufacturer parts list or a parts supplier crossâreference before ordering.
What symptoms indicate the â˘heatingâ element assemblyâ is faulty?
Common â˘symptoms include: the dryer tumbles but produces no heat or â˘very low heat,a burning or metallicâ smell,visible break âor open coil when âinspected,or the dryer repeatedly trips the âŁcircuit breaker.Note: a blown thermal fuse â¤or blocked âvent can âcause⢠similar âsymptoms, so inspect these as well.
How do I test â¤the heating element assembly with a multimeter?
First disconnect power at the breaker.⣠Accessâ the⢠element and disconnect the element’s wiring. Set your âmultimeter âŁto âcontinuity or âthe⤠lowâ ohms range. Measure âbetween the element terminals – you should see⣠continuity â(typical resistance values⢠for â¤electric dryer⤠elementsâ commonly fall in the roughly â5-20 Ί range âdepending on wattage and design; ~10-15 Ί is common). An open (infinite) reading âmeans the⣠element coil â¤is⣠broken.Also check for a short to ground by measuring eachâ terminal to the metal housing – any continuity⣠there indicates theâ element âis shortedâ and⣠should âŁbe replaced.
Is theâ 137392700⢠compatible with gas dryers?
No.Theâ 137392700 âis an electric heating element assembly and is not used in gas⣠dryers. Gas dryers use a gas burner assembly and⢠ignition/valve⤠components;⢠replacingâ an electric element in a gas â˘dryer⢠is not applicable.
Can I replace the â˘heating element myself and⢠what safety precautions/tools are needed?
Yes, aâ competent diyer or technician can replace it. Safety: disconnect power⢠at âthe breaker (do not rely on the cord), wear gloves⢠and eye protectionandâ be careful of sharp sheet metal. Tools typically ârequired: âscrewdriver or nut driver set, pliersand optionally a multimeter for testing. âProcedure overview: unplug âŁpower,â remove â¤access â˘panel (rear⢠or âfront depending onâ model), noteâ and disconnect â˘wires from the element, remove mounting screws and take â˘out the old â˘element, install the new assembly, reconnect wires,⢠reassemble and restore power. Also check/replace thermal â¤fuses or thermostats â˘if they failed.
What commonly causes a dryer heating element to fail?
Typical causes⣠are: lintâ buildup that insulates/overheats the element, a short âŁwhere the coil âcontacts the metal housing, age and wire/coilâ fatigue, poor â¤ventilation causing overheatingor failures âin thermostats/controls that leave the element powered continuously. Regular cleaning of the lint screenâ and âexhaust âvent reduces premature failures.
If the âheating element tests good but the dryer still doesn’t heat âwell,what should I⣠check next?
Check⤠the thermal fuse andâ highâlimit thermostat (these oftenâ fail open),the cycling thermostat,the lineâ voltageâ at the dryer (electric dryers requireâ two hot legs),the timer or electronic control,the heating relay/terminal block,and⣠the exhaust vent for restriction. Also verify the household breaker(s) supplying the dryer âareâ not tripped and that⣠both hot legs âare present (240 V).’
How much⣠does the â137392700 cost and â˘isâ it an âOEM or⣠aftermarket part?
prices vary by seller⤠andâ region,⣠but expectâ a typical range of roughly $30-$120. The 137392700 âŁis sold as âan⤠OEM Frigidaire/Electrolux replacement part by many suppliers; aftermarket equivalents also exist. Check the seller listing to confirm⢠OEM vs â˘aftermarketand âreview warranty/return policy-OEM parts frequently carry â˘a limited warranty from the supplier or manufacturer.
Theâ Wayâ Forward
The 137392700 Frigidaire Dryer Heating element Assembly is a central component responsible for generating the heat required to effectively âand efficiently â¤dry laundry. Its condition directly influences cycle time,â energyâ use, garment care and âoverallâ appliance performance; a⤠compromised or failing heating elementâ can âlead to inadequate heating, prolonged drying, reducedâ efficiency and, âin⢠certain â˘specific cases, electrical or fire risks â¤if left unaddressed.
Proper⢠diagnosis⣠and replacement when necessary are essential⤠to ârestore safe, âreliable operation. Accurate troubleshooting – including visualâ inspection and electrical testing of âŁthe element and related thermal controls – helps identify the â¤trueâ cause of âheating problems âand avoids unnecessary parts â¤changes.When replacement⣠is required,â using the correct assembly and following recommended installation and safety⤠procedures (or engaging a qualified service technician) ensures compatibility, preserves â˘appliance performance and reduces the likelihood of repeat failures. Thoughtful, methodical âŁrepair âmaintains âŁboth efficiency and safety over âthe life of the dryer.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
