241860801 Frigidaire Refrigerator Ice Container Assembly is a refrigerator ice storage and interface component designed to collect, retain and deliver ice produced by the appliance’s icemaker. It is indeed a molded bin and assembly that typically includes the ice hopper, mounting points, sensor cutouts or mounts for level switchesand mechanical interfaces to the dispenser or auger drive; in some model variants the assembly also incorporates a lid, release mechanismor guide surfaces that control how ice moves from the icemaker to the user-accessible outlet.
Inside the appliance system the ice container serves as the intermediary between the icemaker harvest cycle and the dispenser/user. It interfaces mechanically with the icemaker chute,electrically with ice-level sensors or switches,and functionally with auger or paddle drives and dispenser actuators; it also affects airflow and temperature around the stored ice and can influence refreeze and clumping behavior. Proper fit and alignment are important to avoid jams, misfeedsor false sensor readingsand the container must be compatible with the enclosure geometry and control signals of the refrigerator model in which it is installed.
In this article readers will find technical coverage of the assembly’s intended function and common variants, guidance on model compatibility and part identification, typical failure symptoms to watch for (such as ice clumping, dispensing failures, sensor faults or clearance-related jams), basic troubleshooting steps to isolate container-related issues, and practical considerations for safe removal and replacement including checking mounting integrity, sensor connections and sealing interfaces. The material is presented to help technicians, engineers and appliance owners make informed diagnostic and replacement decisions without prescriptive repair instructions.
Table of Contents
- Function and Role of the Ice Container Assembly in Refrigerator Ice Production and Dispensing
- How the 241860801 Frigidaire Refrigerator Ice Container Assembly Operates Internally: Interaction with Evaporator, Auger and Sensors
- Common Failure Symptoms and Diagnostic Tests for Ice Container Assembly Faults
- Compatibility, Replacement Considerations and Installation Procedure for the 241860801 Ice Container Assembly
- Q&A
- In Retrospect
Function and Role of the Ice Container Assembly in Refrigerator Ice Production and Dispensing
The primary role of the 241860801 Frigidaire Refrigerator Ice Container Assembly is to receive ice from the icemaker, store it in a controlled chamberand present it to the dispensing mechanism in a way that prevents bridging and jamming. the assembly mounts directly beneath the icemaker output and either mates with an auger drive or a gravity-fed dispenser gate; correct axial alignment of the auger coupling and secure engagement of the mounting tabs are necessary for reliable feed. The bin also provides a measured volume for the icemaker’s bin-full switch or optical sensor to accurately control ice productionand its molded geometry guides ice toward the dispenser while minimizing friction points that promote ice clumping.
- Material and design reduce frost buildup and resist cracking from thermal stress.
- Interfaces: mechanical coupling for auger motors and position for bin-full sensors.
- Typical failure modes: cracked walls, warped mounting lugs, worn auger couplingor clogged drainage that cause misfeeds.
For technicians and appliance owners,assessing compatibility and function means checking physical fit,sensor continuity,and smooth operation of the feed path; replacing the container typically resolves issues where ice is not delivered consistently or the bin-full detection is unreliable. Practical examples include verifying that the auger shaft engages without binding after replacement, confirming the bin-full microswitch actuates at the correct ice level using a multimeterand inspecting drainage passages for trapped scale or debris that can freeze and obstruct flow.When selecting a replacement, match the 241860801 Frigidaire Refrigerator Ice Container Assembly to the refrigerator’s model series and inspect mounting lug dimensions and sensor/auger interface types to ensure plug-and-play compatibility.
| Item | description |
|---|---|
| Part | 241860801 Frigidaire Refrigerator Ice Container Assembly |
| Material | High-density polypropylene with reinforced mounting bosses |
| Interfaces | Auger coupling receptacle, bin-full switch/optical sensor position, mounting tabs |
| Typical capacity | Holds the last ice production cycle (varies by model, nominal 2-4 lb) |
How the 241860801 Frigidaire Refrigerator Ice Container Assembly Operates Internally: Interaction with Evaporator, auger and Sensors
the 241860801 Frigidaire Refrigerator Ice Container Assembly receives ice released from the evaporator during the harvest cycle and provides the mechanical interfaces and sensor mounting required for reliable dispensing. As the evaporator’s heater or hot-gas cycle frees the ice cubes, they drop into the container where an auger driven by a splined coupling rotates to move cubes to the dispenser chute. The assembly houses the bin-full and jam-detection sensors in fixed positions relative to the auger shaft; correct part fitment ensures those sensors see the expected obstruction and clear states. In practice, using this exact assembly maintains proper alignment of the auger drive, sensor actuatorsand mounting tabs so the ice maker control board receives accurate status signals; substituting a non-compatible bin often results in mis-trips, repeated harvest cyclesor physical jams at the dispenser door.
- Sensor type and placement that affect control signals and harvest timing
- Auger drive interface (splined shaft and clutch behavior)
- Mechanical mounting and alignment for evaporator-to-bin drop path
- Capacity and geometry that influence cube bridging and jamming
Electrically, the bin sensors present either open/closed or logic-level inputs to the refrigerator’s control board; a stuck or misaligned sensor will cause the controller to either skip dispensing steps or repeatedly run the harvest. The auger motor is typically protected by stall detection in the controller or an inline thermal cutout-if torque increases because of bridged cubes or a foreign object, the motor will either stall and trip protection or produce a steady draw and audible strain. Troubleshooting should start with verifying that the evaporator harvest completed (ice released), the ice follows a clear vertical path into the binand that the auger coupling engages smoothly; symptoms such as a humming motor with no rotation, intermittent dispenser feedor continuous harvest cycles point to sensor misalignment, auger drive wear, or an incompatible bin fit rather than the evaporator itself.
| Item | description |
|---|---|
| Auger drive | Splined coupling interface that transmits torque from the dispenser motor; requires correct axial alignment to avoid wobble and wear. |
| Bin Sensors | Binary or optical sensors mounted on the assembly that signal bin-full, emptyor jam conditions to the control board. |
| Evaporator Interface | Drop path geometry and mounting points that ensure ice released from the evaporator lands clear of the auger and sensor mechanisms. |
Common failure symptoms and Diagnostic Tests for Ice Container Assembly Faults
the 241860801 Frigidaire Refrigerator Ice Container Assembly is the structural ice storage and delivery interface that collects ice from the icemaker, interfaces with the dispenser/auger assemblyand secures into the freezer cavity. In normal operation the container must align with the dispenser drive, seat correctly on its guide rails, and maintain clearances to prevent ice bridging or mechanical interference; failures commonly arise from cracked walls, broken mounting tabs, worn bearing surfacesor incorrect seating that allow the auger to bind or the bin sensor to fail. Understanding the container’s mechanical interfaces and materials (rigid plastic shell, molded mounting bosses) helps technicians determine whether problems are caused by the bin itself or by related subsystems such as the auger motor, drive coupleror temperature control inside the freezer compartment.
- Ice bridging or clumping: ice accumulates and does not dispense cleanly.
- Mechanical binding or grinding noise: auger contacts the bin interior or mounting flange is misaligned.
- Dispenser motor runs but no ice dispenses: broken auger paddles, stripped coupler, or sensor misalignment.
- visible cracks or broken tabs: bin fails to seat securely or leaks water during harvest.
- Intermittent sensor detection: bin present/absent signals inconsistent due to damaged magnet or switch.
| Item | Description |
|---|---|
| Part Number | 241860801 Frigidaire Refrigerator Ice Container Assembly |
| Function | Ice storage, dispenser interface, mechanical mount to freezer cavity |
| Compatibility | Common Frigidaire models using removable ice bin assemblies - verify model number before replacement |
| Common Fault Modes | cracked shell, broken mounting tabs, worn bearing surfaces, sensor/magnet misalignment |
Diagnosing container faults begins with a visual and mechanical inspection: check for deformation of mounting tabs, wear on the auger boreand any plastic fragments inside the bin path. Perform a manual rotation test of the auger with the bin installed (power off) to feel for binding and note any contact points; if binding occurs only with the bin in place, the container geometry or seating is the likely cause. Electrical checks include measuring dispenser/auger motor current under load and verifying continuity of any bin-present switches or magnets with a multimeter; an abnormally high motor current or a motor that stalls under low torque usually indicates a mechanical obstruction or damaged auger rather than an electrical fault. Replace the 241860801 bin when structural damage or persistent misalignment is confirmedand re-evaluate related components (drive coupler, motor, sensor) to ensure full system compatibility and reliable operation.
Compatibility, Replacement Considerations and Installation Procedure for the 241860801 Ice Container Assembly
241860801 Frigidaire Refrigerator Ice Container Assembly is the molded bin that receives harvested ice from the icemaker, aligns the ice outlet with the auger/dispenser mechanism and provides mounting points for any level sensors or bail switches. Compatibility depends on the physical envelope (width, depth, mounting tab spacing), the location and type of the harness or sensor connectorsand the interface to adjacent components such as the auger housing or chute. Technicians should verify model and serial numbers against service parts lists and confirm that mounting tabs, screw bosses and sensor cutouts match the refrigerator model; examples include differences between counter-depth and standard-depth freezer liners that change how the container seats and engages the dispenser motor shaft.
The replacement and installation procedure follows mechanical verification, safe disconnection and careful mechanical alignment to avoid ice jams or sensor misreads. Typical replacement actions include removing the freezer shelf, disconnecting power, sliding out the old container, transferring any clips or sensors if requiredand seating the new container so that the auger shaft and sensor actuators engage without lateral preload. After reassembly,restore power and run at least one harvest cycle to confirm ice flow and actuator timing; if the dispenser motor stalls or the auger slips,recheck shaft engagement and clearance for frozen buildup. Practical issues encountered in the field include worn mounting bosses that require a retained clip transferand misaligned containers that allow warm-air ingress and lead to icing in the chute.
- Typical installation steps: disconnect power, remove shelf and old container, inspect mounting points and harness, transfer clips/sensors if needed, seat new container, secure fasteners, restore power and test harvest/dispenser.
| Item | Description |
|---|---|
| Dimensions | Model-specific; verify width/depth against service diagram for proper seating |
| Mounting interface | Tabs and screw bosses that align with freezer liner; sensor cutouts may vary |
| Material | Thermoplastic with reinforced bosses; tolerances affect fit and thermal expansion |
| Compatibility check | Confirm part number against Frigidaire parts list and visual match to existing container |
Q&A
what is the 241860801 Frigidaire Ice Container Assembly?
241860801 is a replacement ice storage bin assembly listed for some Frigidaire refrigerators. The assembly is the plastic bin that collects and holds cubes or crushed ice inside the freezer and, on dispenser-equipped models, provides the interface (bin lip, auger pocket or coupling area and sometimes a lid or chute) between the ice maker and the dispenser mechanism.
How do I confirm 241860801 is the correct part for my refrigerator?
Confirm compatibility by using your refrigerator’s full model number (found on the ID plate inside the fresh-food or freezer compartment) and searching that model on Frigidaire’s parts lookup, a reputable parts siteor an official dealer. The part number alone does not guarantee fit across all models; always match the refrigerator model to the part listing before purchasing.
How do I remove and install the ice container assembly?
General procedure: 1) Disconnect power to the refrigerator (unplug or switch off the breaker). 2) Open the freezer door and, if necessary, remove any shelves blocking access. 3) For most bins: lift the front slightly and pull the bin straight out; for other designs press release tabs or remove a retention screw(s) and then slide out. 4) Inspect the auger coupling or drive area for ice jams and clear if needed. 5) Position the new bin so the drive coupling/auger pocket aligns, slide it fully into place until it seats or clicks, reinstall any screws or shelvesand restore power. Refer to your model’s service manual for model-specific steps.
Do I need any special tools to replace 241860801?
Usually no special tools are required-many ice bins are tool-free and remove by hand using release tabs or a lift-and-pull motion. Some installations use one or two small screws or retainers (Phillips screwdriver or nut driver). Have a towel available to catch any spilled ice and a flashlight for visibility. if clips are brittle or screws are corroded, basic hand tools might potentially be needed.
How should I clean the ice container assembly?
Remove the bin and empty ice. Wash with warm water and mild dish soap using a soft cloth or sponge, rinse thoroughlyand air dry completely before returning to the freezer. Do not use harsh solvents, bleachor scouring pads that can damage plastic. Do not put most ice bins in a dishwasher unless the manufacturer specifically states it is dishwasher-safe-high dishwasher temperatures can deform the plastic.
What common problems indicate the ice container assembly is failing or needs replacement?
Signs include visible cracks or breaks in the bin (leading to ice spillage), warped edges preventing the bin from seating properly, a broken or worn auger pocket/drive coupling that prevents the auger from engaging, persistent ice jams around the bin/chute, or a bin that does not lock into place causing dispenser malfunctions. Physical damage or missing retention tabs are common reasons to replace the assembly.
Is 241860801 an OEM part and can I use aftermarket alternatives?
241860801 as listed by Frigidaire would be an OEM (factory) part if purchased from Frigidaire or an authorized dealer. Aftermarket parts may be available and can be less expensive, but quality and fit can vary. If you choose aftermarket, verify fit for your exact refrigerator model and check return policies and warranties. OEM parts typically offer the best fit and finish for factory compatibility.
I replaced the ice container but the dispenser still won’t work – what should I check next?
After confirming the bin is installed and seated correctly, check: 1) auger motor (listen for motor operation when dispensing); 2) auger shaft/coupling for broken teeth or slippage; 3) dispenser actuator and door switches for proper operation; 4) wiring harness connections between the dispenser, motor and control board; 5) ice maker output (is there ice available?) and any ice jams in the chute. If electrical tests are needed, disconnect power first and use a multimeter or call a qualified technician. If uncertain, consult model-specific diagnostics or a service technician.
In Retrospect
The 241860801 Frigidaire Refrigerator Ice Container Assembly plays a central role in the ice management system by providing secured storage,maintaining hygienic separation of ice from the refrigerator interior,and interfacing with the ice-making and dispensing mechanisms to support reliable delivery.As a purpose-designed component, it helps ensure consistent portioning and protection from contamination while contributing to overall appliance performance and user convenience.
Because symptoms of a failing ice container can overlap with issues in the ice maker, augeror dispenser, accurate diagnosis is important to identify the root cause and avoid unneeded repairs. When replacement is required, installing the correct assembly-preferably the specified OEM part-and following manufacturer guidance or qualified service practices helps restore proper function, preserve efficiencyand reduce the risk of additional damage. Proper assessment and timely replacement therefore help maintain food safety, appliance reliability, and the expected performance of the refrigerator’s ice system.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
